Search Documents

By Donlad B. Lindsay

This report describes a field-test program to determine the effectiveness of a polymeric wall sealant to reduce the excape of naturally occurring radio-active gas radon from the walls of an underground uranium mine into the ventilation air. A 75-foot-long, dead-end drift with a surface area of about 6,000 ft2 was used as the test site in which the average natural radon flux from the normally dry rock was 16 fCi/cm2-s. The effect on radon emanation of wetting the walls with water to a depth of 3 inches was tested, after which the rock was completely covered with a coating of dry-mix concrete to provide a base for the sealant, an acrylic latex. Sealant was applied in two coats to about 0.25 mm thick. An overall reduction of average radon flux of about 75 pct was achieved. Radon production and other environmental values were measured continuously and automatically by a Bureau of Mines data acquisition system. A commercial microcomputer was programed to convert raw data to engineering units and to perform other useful operations while recording all data on magnetic diskettes. Direct measurements of radon flux from the rock surface were made by a charcoal adsorption technique.

Jan 1, 1981

By W. J. Kroll

This report is concerned with the many sidelines that were investigated incidental to developing a process to produce ductile Zirconium by members of the staff of the Bureau of Mines laboratory, Albany, Oreg. The results of the main investigation, concerning the production of malleable zirconium by reduction of chloride with fused magnesium under helium, have been described in previous publications. These should be taken as a background to facilitate understanding of this work. Literature on the metallurgy of zirconium has been summarized in a separate publication (2), and references are given in this report only when new publications have to be considered or old ones stressed. Most of the observations described in this report can be applied to the problems involved in making titanium with virtually no change. In general, titanium is easier to reduce than zirconium, since its affinities are lower. Also, its chloride is easier to handle and keep clean because it is a liquid at room temperature.

Jan 1, 1952

By Merwin H. Howes

In constructing the NORAD Combat Operations Center, controlled blasting techniques were employed to achieve smooth walls and to avoid shattering the rock beyond excavation lines. Extraordinary measures were taken to stabilize the rock to permanently preserve the openings. Rock stabilization was accomplished by means of reinforced concrete and gunite linings, rock boltings, installation of chain-link fabric, and epoxy resin and cement grouting. A particular zone of weakness at B vital location was supported by exceptionally thick reinforced concrete lining, rock bolts, and cement grout.

Jan 1, 1966

By H. F. Yancey

The Baum-type jig used so widely to clean bituminous coals has not been adopted for anthracite. If proved suitable for anthracite, its use might lower preparation costs in some plants. Cleaning trials on a Pennsylvania anthracite in a laboratory-size Baum-type jig were undertaken by the Bureau of Mines to provide indicative information that would be helpful in determining whether the cost of a full-scale installation would be justified. Clean coal surpassing standard anthracite specifications was obtained in all sizes from Stove through No. 5 Buckwheat. Recovery effi¬ciencies were acceptable down to 3/16-inch size, but there was excessive loss of coal in the finer sizes. Thus the fine refuse produced in a commercial plant might re¬quire retreatment. A comparative cleaning trial in a dense-medium pilot plant provided a recovery efficiency only l percent higher than obtained in jigging.

Jan 1, 1957

By A. J. Kauffman

This inventory of the industrial mineral resources of the Pacific Northwest indicates that each of the States comprising this great region annually produces nonmetallic materials valued at mans million dollars. Commodities or their products that have a large, localized market predominate. These include Portland cement, sand and gravel, stone, clay, and lime. The region's output of magnesite, vermiculite, pumice, and diatomaceous earth is outstanding. The magnesite deposits of Stevens County, Wash., are the largest and most important in this country. Mast of the domestic vermiculite production is obtained from deposits in Lincoln County, Mont. Oregon and Idaho rank third and fourth, respectively, as domestic pumice producers. Production data for diatomaceous earth show Oregon second and Washington fourth among the producing States.

Jan 1, 1952

By J. D. Davis

THE carbonizing properties of one medium- and and five low-volatile coals from West Virginia and one high-volatile A and two medium-volatile coals from Pennsylvania were determined by 800° and 900° C. BM-AGA carbonization tests and expansion tests in the sole-heated oven. Plastic properties of the coals and the yields and quality of their cokes and other carbonization products were determined. The low-volatile coals comprised a mine and a coke-plant sample of Pocahontas No. 6-bed coal from the. Black Eagle No. 1 mine, Wyoming County, W. Va.; a mine sample of Pocahontas No. 6 bed from the Louisville mine, Mercer County, W. Va. ; Davy Sewell bed was sampled at the Twin Branch mine, McDowell County, W. Va.; and Fire Creek bed was sampled at the Dunedin No. 1 mine, Raleigh County, W. Va. The medium-volatile coals were from the Fire Creek bed, Laurel Creek mine, Greenbrier County, W. Va.; Lower Kittanning bed, Springfield No. 4 mine, Cambria County, Pa.; and Upper Kittanning bed, Springfield No. 6 mine, Clearfield County, Pa. The high-volatile A coal represented the Upper and Lower Freeport beds, Kent Nos. 1 and 2 mines, Indiana County, Pa. In addition to the coals listed, high-volatile A coal from the Pittsburgh bed, Warden mine, Allegheny County, Pa., a standard blending coal, was used in blends in this investigation.

Jan 1, 1950

By Wilbur I. Duvall

In a review of so 40 papers on damage to residential structures resulting from blasting, only 3 were found that present data on the observed amplitude and frequency of the vibration levels produced by blasting together with an observed degree of damage to a residential structure. The data from these three reports have been analyzed statistically to determine if one of the quantities, displacement, velocity, or acceleration, is more reliable than the others for estimating the degree of damage to a residential structure. From this analysis the conclusion is drawn that a given degree of damage to a structure is most closely related to the magnitude of the particle velocity of the wave motion passing thru the earth at the structure location. On the average, only minor damage it observed for peak particle velocities of 5.4 inches per second, and major damage is observed for peak particle velocities of 7.6 inches per second. When the spread of the data is taken into consideration, the following statement can be made: Wave motions that have a peak particle velocity in excess of 2 inches per second have a fair probability of producing some damage to structures, whereas wave motions that have a peak velocity less than 2 inches per second have a very low probability of causing any damage. Therefore, the recommendation is made that vibration levels in the vicinity of residential structures should be maintained below a peat particle velocity of 2 inches per second. The above criterion for safe blasting is considered to hold over a wide variety of soil and rock conditions because the original data were obtained for a wide range of soil and rock conditions and on various types of residential structures. INTRODUCTION Ever since explosives were discovered and developed for mining purposes, there has existed the problem of what effects the air and ground vibrations resulting from blasting have on structures of various types. This problem is

Jan 1, 1962

By Jacqueline V. Rich

The relationship between surface and ground water quality and copper mining in the Globe-Miami area is investigated in this three-year study. Methods to prevent, minimize, mitigate, or treat polluted waters are identified and evaluated. Best Management Practices are incorporated in a recommended plan to manage the area's water quality.

Jan 1, 1983

By Donald F. Reed

In the Coastal Plain sedimentaries of northeastern Mississippi, high-alumina clays and kaolins, which are bauxitized locally to varying degrees, are found in many places along the contact between the Midway (Paleocene) and the Wilcox (Eocene) series. The trace of the contact extends from Tippah County, on the Tennessee border, south to Winston County, thence southeast to Lauderdale County, and into Alabama. Its length within Mississippi, disregarding sinuosities, is 185 miles (fig. 1). Commercial production of bauxite from the region has amounted to about 400 tons, shipped from one outcrop in Komper County. In December 1941 and January 1942, the Bureau of Mines and the Federal Geological Survey made a reconnaissance survey of the contact zone and selected the most promising areas for further study. In 1942, four areas in Benton, Union, and Pontotoc Counties were investigated by auger and rotary core drilling, and in 194, core drilling was done on five areas in Kemper, Noxubee, and Winston Counties. The present report records the work done by the. Bureau of Mines and the factual data obtained from the investigations of the nine areas in the two projects.

Jan 1, 1952

By Phillip N. Yasnowsky

This Bureau of Mines publication tabulates State taxes levied on nonfuel minerals that have the characteristics of a severance tax.

Jan 1, 1978

By R. S. Dean

[Methods s of preparing the manganese metal that has been used in chemical and metallurgical investigations have passed through a cycle. Most of the investigations made e before the turn of the century, used Moissan's pyrophoric man manganese.3/ This material was made b; electrolysis into a mercury cathode and distillation in vacuo. The material was essentially pure, and investigations in which it was employed (with proper precautions against oxidation) led to accurate results on tie intrinsic behavior of metallic manganese.]

Jan 1, 1941

By Guy Ervin, Delwin D. Blue, John E. Conley

"INTRODUCTION Extraction of alumina from various materials, such as low-grade bauxite and clay, by means of a lime-soda sinter has been the subject of a number ofinvestigations (1, 2, 3, 4, 5, 7, 9, 10, 11, 12, 13, 16, 17). 5/ in recent years, Although many of the details of these investigations are lacking, it is believed that there is one difficultly that frequently develops under certain conditions, namely, that of thickening or gelation of the slurry formed during extraction of the sinter. If gelation occurs even to a slight extent* Serious mechanical difficulties result, very low liquor recoveries are obtained, and the extraction step becomes virlually inoperable. Under 'favorable conditions, a solid gel is formed which can only be removed from the equipment with great difficulty. At the Eastern Experiment. Station of the Bureau of Mines in College Park, Md., a study of lime-soda processes was begun in November 1941. This work has included studies on low-grade bauxites, kaolin clay, and nodular diasporic clay. Gelation was most serous with kaolin clay and least with diasporic clay. As a part of the Bureau's investigation, a study was made of the effect of the pertinent variables on gelation. The results permit the selection of various sets of conditions at which gelation will not occur. These data are essential to the final selection of optimum conditions for the over-all process."

Aug 1, 1946

By J. P. Morris

"INTRODUCTION In the investigation being conducted by the Bureau of Mines concerning the production and utilization of sponge iron, it soon became evident that more information was needed regarding methods for determining the degree of reduction attained in the manufacturing process. Sponge irons made by different processes vary in physical characteristics and chemical composition, and a method of analysis that is suitable for one type is not necessarily applicable to all others. For example, the hydrogen-evolution method, which measures the volume of hydrogen evolved upon treating the sample with acid, accurately determines the oxygen content of some types of sponge iron. However, when the sponge iron contains combined carbon, hydrocarbon gases are also-evolved and large errors may result. Probably no single method will give accurate results in all instances, and for this reason it is desirable to have several reliable procedures available and to know the limitations of each.For measuring the degree of reduction, determination of either metallic iron or oxygen should suffice, although for practical application of sponge iron to the production of steel the oxygen content is more significant. After consideration of proposed methods of analysis in regard to their suitability for routine use and the probable influence of other substances, four procedures were chosen for investigation:(1) Mercuric chloride method.(2) Copper sulfate method.(3) Hydrogen-reduction method.(4) Hydrogen-evolution methods."

Sep 1, 1945

By J. H. Crary

This report summarizes the results of a one-year agreement for research on the electromagnetic environment in coal mines, which was conceived as the beginning of a long term cooperative program between ITS and the Bureau of Mines. The concepts on which it was originally based are a result of the report on mine rescue and survival by the Committee on Mine Rescue and Survival Techniques of the National Academy of Engineering, dated March 1970. This report drew particular attention to the need for improved communications during and following mine disasters. In particular, the outstanding problems identified were the location of, and communication with, trapped miners. Some tentative solutions, generally involving long-wave electromagnetic signals, were offered. Consideration of the problems of disaster location and communication soon leads to consideration of the communications techniques (or lack of them) for use under normal mining conditions. In particular, if a disaster communication and/or location system is to be readily available and operable under disaster conditions, it should also be usable during mining operations. In this way operators can become familiar enough with the system to operate it during disaster conditions, as well as provide a mechanism for regular testing.

Jan 1, 1972

By M. C. Irani

This study is a survey of supply and demand for minerals, metals, alloys, and compounds used by the chemical industries in the Ohio River Basin (ORB) area of Ohio, Pennsylvania, and West Virginia during 1967. Data for the study were obtained from completed questionnaires received from chemical manufacturers and from interviews with officials of chemical companies and mineral producers and distributors. The information includes kind, quality, quantity, values, sources, specifications, uses, and methods of transportation. Results of the study show that of the total value of mineral materials consumed by the chemical industry, manufacture of inorganic chemicals consumed 46 percent; fertilizers, 22 percent; and soaps and detergents, 19 percent. Fifteen commodities accounted for 91 percent of the total value of mineral materials consumed. Five of these--phosphates, potash, salt, sulfur, and titanium dioxide--accounted for 59 percent of the total.

Jan 1, 1970

By G. M. Kintz

"Methods and costs of rock-dusting bituminous coal mines have been discussed in various publications by the United States Bureau of Mines and others.3 This paper discusses the present methods and cost of dusting at the Swastika mine of the St. Louis, Rocky Mountain and Pacific Co., Raton, N. M.In the Swastika mine the recommendations of the United States Bureau of Mines with regard to rock-dusting are followed at least as well as in any mine in the States of Wyoming, Colorado, and New Mexico. This mine is located at Swastika, N. M., approximately 4 miles west of the town of Raton and is in the Raton coal seam. The mine is rated as gassy and produces approximately 1,000 tons of coal per day.A mining system known as the ""room-and-pillar with cut-offs"" is used which results in recovery of nearly 100 per cent of the coal. The mine employs approximately 250 men.Ventilation is maintained by a Sirocco fan so arranged that the air current may be reversed and exhausting approximately 130,000 cubic feet of air per minute at 3 inches water gauge. This fan is supplemented by two auxiliary fans for emergency use. Three main entries penetrate the hill in a straight line for approximately 8,000 feet. The haulage is through the center entry, which is also used as the intake in conjunction with a two-compartment concrete-lined shaft located at the end of the entries. The main return for 3,000 feet inby the fan is 12 feet wide and 7 feet high. For this distance the ribs have been reinforced by a wall made of coke-breeze blocks plastered over with cement. Solid concrete blocks are used for the top row of blocks of the wall. Steel 10-inch I-beams spaced 40 inches apart center to center are supported on these solid blocks and thus support the roof. The next 1,000 feet inby has the same area, but the cement blocks extend to the roof, as no crosspieces are needed. The airways are kept clean and well rock-dusted.A rather unique system is used to handle gas feeders along the intake and haulage entries. There these feeders occur in the roof or where gas is apt to collect in high points along the haulage, tin funnels as large as 3 feet in diameter are placed near the roof. From these a 2-inch or other suitable-sized pipe is run into the return through the wall of the nearest break-through. A valve on this pipe line controls the amount of air pulled. These devices keep the high places clear of any gas, even when strong feeders are encountered.Fifteen-ton electric trolley locomotives are used on the main haulage and approximately 30 roller-bearing oars, each having a capacity of approximately 3,000 pounds of coal, compose a trip. All loaded tripe carry steel drags on the last car, and automatic derails are located at advantageous points throughout the mine.All loaded trips are thoroughly sprinkled on the sectional partings and at the main parting. The track is sprinkled every idle day, or if needed, every day; from a large tank mounted on a truck hauled by a motor. Neither nozzle nor spray is used, as these were unsatisfactory. The water leaves the tank. through a 11/2-inch valve and is permitted to flow on the road through a horizontal 11/2-inch T. Water is obtained from filling stations located throughout the mine. It is stated by the officials that the use of this method of sprinkling permits the entire haulage roadbed to be wetted down in two hours."

Mar 1, 1930

By Richard A. Winters

There are no producing or developing mines or active mining claims in the Deschutes Canyon RARE II study area. Only two prospects were found; they have no identified potential for mineral resources. Thin diatomite deposits occur in the Pliocene Madras Formation. Development of sand and gravel deposits in the area could not favorably compete with similar deposits in the surrounding area which are closer to points of use. By mid-1982, active oil and gas lease applications covered about 25 percent of the area, a reduction from nearly 100 percent in early 1981. No holes were drilled for oil and gas exploration. INTRODUCTION Personnel of the Bureau of Mines, Western Field Operations Center conducted a mineral investigation of the Deschutes Canyon RARE II area during the summer of 1982. The area, about 10 mi (16 km) southwest of Madras, Oregon, covers 10,890 acres (4,407 ha) in the Crooked River National Grasslands (fig. 1). The Deschutes River has incised a deep canyon into the north sloping elevated lava plain near the transitional boundary of the High Lava Plains and the Deschutes-Umatilla Plateau geomorphic divisions (Baldwin, 1964, p. 20).

Jan 1, 1983

By Richard W. Lusignea

This report describes a program to evaluate the feasibility of determining roof features which occur in United States coal mines from changes in bolting machine drilling parameters. The ultimate purpose of this effort is the development of an instrumented roof bolting machine which can detect hazardous roof conditions and/or indicate when the existing roof control plan is inadequate. A survey of hazardous conditions occurring in United States coal mines is included, along with the slang expressions for these conditions, and their relative degree of hazard. Specific machine parameters are identified for detecting the specific roof conditions. Measurement concepts are proposed using readily available instrumentation in most cases. Various systems are evaluated and tradeoffs presented. An implementation plan is proposed for developing a prototype system and using it in an operating coal mine.

Jan 1, 1978

By Robert C. Merritt

This report describes laboratory as well as pilot heap leaching investigations of low-grade sandstone ores from Wyoming, New Mexico, and Colorado. Sodium carbonate-bicarbonate solutions containing sodium hypochlorite extracted up to 86, 54, and 16 percent U308 from Wyoming, New Mexico, and Colorado ores, respectively. Ammonium carbonate-bicarbonate solutions containing sodium hypochlorite were less effective at leaching these ores. Acid leach in replicate pilot plant testing resulted in U308 extractions of 96, 88, and 81 percent from the Wyoming, New Mexico, and Colorado ores. The development of cost-effective processes for extracting uranium from low-grade ore is essential to the assurance of a continuing domestic supply of uranium.

Jan 1, 1977

By Charles F. Jackson

Gold mining is a subject that not only appeals to the popular imagination but has vital importance to the world's economic structure. However, a discussion of the use of gold as a medium of exchange, and a basis for credit between nations and for monetary systems is not within the scope of this paper. The importance of gold in carrying on the commerce of the world, the present supply and rate of production, the probable trend of future production, the probable future requirements, and related subjects have recently received much attention from bankers and economists, and many articles on these subjects have been published. During slack periods of base-metal production due to falling prices, accompanied by scaling down of base-metal mining operations and often by the closing down of at least some mines, there usually result revival of interest in gold mining, search for previously undiscovered deposits, and reopening of some old gold mines.

Jan 1, 1932