Search Documents

To provide cooler air to miners working in hot areas of mines, particularly new deep hardrock mines. Approach Air supplied to hot working areas of mines is cooled by passing it through a series of water sprays. How It Works Water nozzles mounted inside a section of ventilation tubing release cooling sprays of water into the air being blown through the tube. The prototype of the water spray cooler consists of six evenly spaced water sprays located inside a 10-ft. long section of 16-inch-diameter fiberglass ventilation tubing. See diagram. This section of rigid tubing is installed into one of the positive pressure ventilation tubing lines that conduct fresh air into working stopes. The intake manifold to the six water sprays is connected to the mine?s cool water line, and the water valve on the manifold is opened. Warm ventilation air being supplied to the stope passes through the water sprays, and is cooled by the lower temperature water.

Jan 1, 1979

By R. V. Ramani, J. M. Mutmansky, P. C. Luna, V. A. Marple, Honglin He, B. A. Olson

The development of a sampling instrument for the assessment of an underground coal miner’s exposure to airborne respirable coal mine dust on a continuous and real-time basis has been long identified as essential for timely initiation of control actions. A respirable dust dosimeter (RDD) which operates on the principle of increasing pressure across a filter media with increasing dust mass on the filter has been developed by the National Institute for Occupational Safety and Health. Comparisons of the performance of the RDD with an U.S. approved gravimetric respirable dust sampler (GRD) have shown that the RDD may meet the requirements for measuring miners’ exposures on a cumulative, near real-time basis such as mid-shift and end of shift exposures. Recently, the performances of the RDD and GRD were compared by conducting side-by-side area sampling experiments in a controlled experimental environment in the laboratory and in underground coal mines under normal operating conditions. In this paper, the results from the in-mine study are presented and discussed. The experimental design for the in-mine study included two mines in different coal seams in different geographic coal regions. To ensure a wide range of concentrations, the experiments were conducted in a continuous miner section in Mine 1, and a longwall face in Mine 2. Airborne dust sampling was conducted for four different shifts at each mine. In each shift, two samples of different exposure durations were collected from two different locations. Each sample consisted of the readings of three dosimeters and the exposed filters from the three paired GRD samplers. As a result, a total of 96 comparative samples were obtained, 48 for each mine. The data were analyzed for the precision of the RDD and GRD measurements and for the relationships between the differential pressure of the RDD and the mass of dust on the paired GRD filter. The analyses indicate that, on the average, the RDD and the GRD track the airborne respirable dust concentrations well, exhibiting both a high correlation between the two measurements and a reliable predictive relationship of one from the other. Details of the experimental design, data analyses procedures, results, conclusions and recommendations of the underground experiments are presented in this paper.

By Herbert H. Einstein

Instability of rock slopes often occurs in the form of excessive movement of bodies that are bounded by discontinuities. The well known limit equilibrium analysis for wedges and blocks suffer, however, from procedural simplifications and from the basic deficiency of limit eguilibrium analysis--the rigid body assumption. Thus, stability analysis for 2-and 3-plane wedges with a wide range of additional features regarding failure modes and external forces have been developed. The deficiency, due to the rigid body assumption, was corrected by an approach that includes the effects or the in-situ stress field and of the stiffness of discontinuities. The final step in making limit equilibrium approaches more valid was achieved with the method of artificial supports which makes it possible to identify among all possible failure modes the critical one and to determine the corresponding factor of safety. The analytical development includes the creation of appropriate computer codes and routines for programmable pocket calculators.

Jan 1, 1979

By M. D. Aldridge

The results of a two-year research effort aimed at improving communication systems in coal mines is reported. A review of communication methods presently used in coal mines is presented. Theoretical and-experimental results of a four pronged effort in the areas of (1) through-the-earth propagation, (2) paging system design, (3) improvement of wired telephone systems, and (4) carrier current systems are described. Auxiliary systems not included in the above are considered briefly. Various conclusions are drawn in light of practical constraints and the needs of the mining industry. The study clearly demonstrated the need for nine communications to be designed on system basis. The viability of new technology for providing reliable mine communication for improving mine safety and operating efficiency is shown.

Jan 1, 1973

By John E. Kelley

A method for measuring the spark-shower radiance of metals when abraded on a grinding wheel was developed by the Bureau of Mines for evaluating the sparking tendency of metals. The radiance was measured in units of emissive power per solid angle per area of the detector. Over 100 metals were tested and rated relative to commercially pure iron. The metals tested included elemental metals, iron binary and ternary alloys, iron-carbon ternary alloys, commercial steels, nonferrous alloys, and a few hard-metal compounds. Some alloys were synthesized; others were obtained commercially. Alloys that possessed good strength properties were emphasized for selection. The results indicate that the spark-shower radiance of plain carbon steels and carbon alloy steels was greater than that of pure iron. Certain elements, particularly vanadium and chromium, reduced the sparking tendency of iron. Stainless steels and particularly nickel alloys displayed low spark-shower radiance. Some metallic elements had much lower radiance than iron; others, much greater. Plain carbon steels, heat treated to a variety of hardnesses, gave radiance values that generally increased with increasing hardness. The effect on sparking tendency of an increase in hardness of an alloy steel was studied. The sparking tendency increased with an increase in hardness to a maximum, then decreased with a further increase in hardness.

Jan 1, 1974

[ ]

Jan 1, 2008

By J. E. Cleveland

The major health concern for uranium miners is the release of radon gas and the resultant ingrowth of the short lived daughters in the mine atmosphere. Present methods of control are the utilization of mine ventilation systems for dilution and control of ingrowth time to maintain working levels below those set by regulations. This study examined pressure cycling efforts on the radon emanation. The mechanical ventilation systems were altered to allow pressure changes throughout the mine to increase radon influx during the off shifts and thus deplete the sources of radon gas. Continuous radon working level and environmental monitors, developed by the Bureau of Mines, were employed to monitor radiation and physical parameters in the mine workings. The mine ventilation system was then varied to induce radon flows during off shifts, thus, depleting the radon sources during normal production shifts. Electro-static precipitators were also tested to determine radon daughter collection efficiencies. Both radon and radon daughter concentrations were monitored and evaluated. Major problems were found in the simple mechanical operation of cleaning these units.

Jan 1, 1982

By Donald B. Lindsay

A new concept was proposed for a personal warning device for use by miners who may be exposed to health hazards from inhalation of alpha-emitting radionuclides, especially radon-222 and its short-lived daughters. Two successive prototype models of the proposed instrument were designed, fabricated and tested. The Personal Alpha Alarm, in its final form, weighs less than 90 g (3 ounces), and can easily he mounted on a miner's safety cap. It is powered r, by electricity drawn from the cap-lamp battery, and consumes less than 100 n A at 4VDC. It is entirely passive and has no moving parts. Alpha-radiation originating in the air around it is detected by a 5 cm2-area semiconductor-type sensor that was developed especially for this purpose. The presence of alpharadiation in the air is communicated to the wearer by means of a small flashing light-a light-emitting diode-clipped to the brim of the safety cap. When the intensity of alpha-radiation exceeds a predetermined threshold, the flashing mode changes to a continuous illumination, thus providing an alarm signal to the wearer. Because the detector senses all alpha-emitters in the air, including 222Rn, it is not able to measure Working Levels accurately. For its intended purpose, however, which is to give a timely warning of excessive levels (several times the normal control level) of radon and/or radon daughters in an individual's air environment, the Personal Alpha Alarm is expected to be a useful instrument.

Jan 1, 1978

By Avery H. Reed

ALABAMA'S mineral industry continued to expand. This was a record year for many commodities, with expansion in almost all industries. New records were established for the production of native asphalt, fixe clay, miscellaneous clay, kaolin, bentonite, lime, scrap mica, salt, sand and gravel, crushed limestone, crushed marble, and tale. Among the States, Alabama ranked second in the production of bauxite, third in the production of scrap mica and native asphalt, and fifth in iron ore. The mineral industry of Alabama was dominated by the mining and processing of coal and stone, the manufacture of cement, and the production of crude petroleum, which together comprised 87 percent of the total value of production, compared with 86 percent in 1963. The iron ore industry continued to decline. This was the first year in which consumption of imported iron ore exceeded the consumption of domestic iron ore. The coal industry recovered from the slump caused by the abandonment of red iron ore mining by United States Steel Corp., and production expanded 17 percent, for the best year in coal mining since 1948. During the year, the one-billionth ton of coal was mined within the State.

Jan 1, 1965

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 9,600 acres of the 12,350-acre Antelope Creek Wilderness Study Area (MT-065-266) in order to evaluate its mineral resources. Within this report, these 9,600 acres are referred to as the study area. The Antelope Creek Wilderness Study Area, Phillips County, MT, adjoins the north end of the Charles M. Russell Wildlife Refuge. Considered part of the Missouri River Breaks, the area straddles the edge of a thrust fault zone that has deformed the Mesozoic strata in the west half of the area. Shale, siltstone, and sandstone of Cretaceous Age are exposed in the area. Coal beds averaging 3.0 ft thick occur in the Judith River Formation. About 0.20 million short tons of coal were mined from the Judith River Formation adjacent to the west boundary of the area; no production is known in the study area.

Jan 1, 1986

By W. G. Phillips

This report presents results from a study whose objective was to evaluate noise control options for existing equipment used in metal and non-metal processing plants. This equipment performs 3 basic functions, crushing, grinding to a point where the product can be liberated from the waste, and agglomeration A the product. Specifically, the study was directed towards taconite processing since the extreme hardness of taconite results in high noise levels and in considerable maintenance of the processing equipment. Both of these factors make this process a very challenging noise control task. Plants processing other ores use similar equipment, consequently the results of these studies should he applicable to a wide variety of plants. The report presents the source diagnosis and potential retrofit noise control treatments for fine screens, mills, crusher sizing screens, and vacuum disc filters. Estimates are make of the noise reduction from each treatment. The report concludes with recommendations for future research on each piece of equipment.

Jan 1, 1978

By L. A. Haas

A kinetic study of the carbon deposition reaction was undertaken by the Bureau of Mines as part of a broad investigation of metallurgical reactions in the iron ore blast furnace. The disproportionation of carbon monoxide on iron pellets was investigated at carbon monoxide pressures between 0.5 and 2 atmospheres (absolute) and temperatures from 400° to 1,075° C. Gas flow in the range from 0.25 to 0.85 standard liter per minute was found to have little effect on the reaction velocity. The addition of nitrogen and helium to caron monoxide exerted only a dilution effect on the rate of carbon deposition. However, an addition of 1 percent hydrogen increased the rate about 100 times. Small amounts of carbon dioxide in the inlet gas exerted little effect on the rate of carbon deposition. The maximum rate for carbon deposition in the first 2 hours occurred at 550° C. The apparent molar activation energies at various stages of the reaction were found to vary from 13 kcal initially to 36 kcal during the latter stages of the reaction. The reaction rate behavior was tentatively explained by an adsorption step followed by the diffusion of iron through a shell of inactive iron carbide.

Jan 1, 1968

A mobile vacuum sweeper to remove loose coal and coal dust from underground coal mine workings was designed, built, tested, and evaluated. The design was based on an extensive test program. Pick up and conveying rates vs. air volumes, velocities, and nozzle shapes were determined for coal rubble in a laboratory pneumatic handling system. A gas/solids separation system was developed and tested in the laboratory capable of separating the solids loading from the vacuum system air stream to the very high degree required to preclude degradation of the ambient (mine) air. Two designs were made, one for belt conveyor and one for general district cleanup. The belt cleanup machine was chosen for test and demonstrated in an underground coal mine performing cleanup work in belt haulageways and on ribs.

Jan 1, 1975

By Clayton M. Rumsey

The U.S. Bureau of Mines conducted a mineral resource survey of the Cinder Cones Wilderness Study Area (WSA) (CDCA-239), 10 miles east of Baker, CA, in 1983. The 44,299-acre WSA is underlain by Precambrian granite gneiss, Upper Cretaceous or lower Tertiary Teutonia quartz monzonite, and Quaternary basalt flows and alluvium. This mineral survey included an examination of two volcanic cinder mines, five lode prospects, two volcanic cinder prospects, and reconnaissance sampling in and near the WSA. The seven prospects are in the WSA; the two volcanic cinder mines are adjacent. No mines are in the WSA. In 1981, there were 61 placer and 3 lode mining claims in the WSA. Sample results from two prospects within the WSA contained significant gold and silver values; however, the mineralized rock is of limited extent and no resources were apparent. Alluvial samples taken throughout the WSA contained only traces of gold. Two volcanic cinder cones within the WSA contain an estimated 30 million tons of cinders. There are sufficient cinders outside the WSA to satisfy demand in the foreseeable future. Stone, sand, and gravel deposits are not resources because similar material is closer to markets. No evidence of energy minerals or geothermal resources was found.

Jan 1, 1985

By Duane L. Abata

This work, conducted under Bureau of Mines contract, deals with the development of a computer graphics software package that will: 1. display mine ventilation schematics and other representative Illustrations for a real-time data acquisition system under development by the Bureau, and, 2. utilize the Bureau-owned Minefire and Ventilation Code for display of ventilation on and contamination predictions. The software package has been written try operate on a 64K, Z-80 based microprocessor-computer. The project has been divided into two phases. The first phase dealt with the development of the graphics software The sec rind phase dealt with the retrofit of the Minefire and Ventilation Code to the Z-80 microprocessor-computer.

Jan 1, 1984

By William A. Hustrulid

A technical and economic evaluation of the potential for improving mining productivity through the use of underreamers in blastholes, specifically in relation to Minnesota taconite, Arizona surface copper and in situ mining operations is presented. Included are (1) a review of the drilling and blasting practices presently being used, (2) a discussion of current underreamer technology. (3) the presentation of a general economic cost model for underreaming, (4) the application of the model to surface taconite, surface copper and in situ mining, and (5) a summary discussion including required performance specifications, potential overall benefits, and recommendations for further development.

Jan 1, 1977

By J. C. Gerdeen

This project was a supporting effort with research contract H0230016 at White Pine Copper Company. Creep properties of White Pine rock were determined. These and properties for bolted joints were used in finite element analyses of sections of the White Pine Mine which included analysis of bed separations in the roof and sloping faults. In-situ experimental measurements were made of tension, compression, and bending of resin bolts by use of strain-gaged bolts. Evaluations of bolting effectiveness and comparisons of predicted and measured roof behavior are given.

Jan 1, 1976

By Fun-Den Wang

This report presents theoretical studies and experimental work dealing with the detection of dangerous roof and pillar conditions in underground mines through measure¬ment of temperature differences on the surface of the mine opening. The theoretical work is directed at modeling the circumstances where a loose slab of rock might be detected. The experimental work provides input data for the theoretical models. At the beginning of the project, little was known by the authors of the conditions that would permit detection of a loose slab of rock or coal by measuring the surface temperature differences. The U.S. Bureau of Mines had found that there were detectable surface temperature differences on the roofs and pillars of mines. The Bureau contracted with Colorado School of Mines to measure temperature profiles around mine openings in an effort to learn if the temperature differences they had detected were directly related to loose pieces of roof and pillar rock. The Bureau was principally interested in learning if loose rock could be found in coal mines by measurement of surface temperature differences with an infrared thermometer.

Jan 1, 1972

By P. B. Grote

The report provides a general description of DOM technology, sources for DOM technology, and identifies approaches and requirements for acquisition by the Enterprise of DOM technology by conventional means. The approaches identified assume the Enterprise enters into a contractual/ joint venture arrangement with an uncommitted and competent systems management firm at various stages of the DOM system acquisition process. The approaches provide for training through work/study as well as through direct participation in acquisition programs. The potential success of the alternatives are evaluated in terms of the likelihood of the acquisition of an ongoing Enterprise economic DOM operational capability. The study concludes that sources exist and that the Enterprise should under-take the development of its own technical capability through conceptual design prior to selecting its source for systems management expertise.

Jan 1, 1980

By H. P. Greenwald, Irving Hartman, H. C. Howarth

"INTRODUCTION A report of tests of seven small pillars formed from the Pittsburgh coal bed in the Experimental coal mine was given in Technical Paper 605 5/ Five additional pillars were tested between July 1939 and. October 1940. The data obtained, in the later tests permit an extension of the conclusions reached in Technical Paper 605, which appears to be important enough to the mining industry to justify a progress report that will explain briefly what it is and how it was obtained. Full detail of the tests will appear in a second technical paper, preparation of which is deferred so that results of pillar tests now under way my be included.DESCRIPTION OF TESTSExcept for minor improvements in operating details, the five additional tests were made as described in Technical Paper 605, pages 2 to 7. Briefly, the desired pillar was formed from the coal bed, by excavating a passage around it (no explosives were used), and enough material was removed from above to permit installation of the assembly used for applying pressure. Each pillar was tested resting on its original fireclay floor, which was restrained from lateral flow by a ring of concrete. Vertical and lateral movement of the pillars in two directions as measured carefully in all tests."

Jun 1, 1941