Search Documents

By Jonathan Heiner

Rio Tinto Bingham Canyon Mine started its South Wall Push Back (SPB) in 2011. This push back will mine through the only road to the pit bottom (the 10%). The pit bottom is the main ore sector for the mine and supplies about 80 to 90% of the ore. In late 2017 the mine set off a blast in SPB that created a small wedge failure on the high wall between SPB and the 10%. This wedge failure released a rock approximately 20 minutes after that blast that rolled down the wall landing on the 10% near and then contacting a light vehicle

Jan 1, 2019

By Jair Alarcón, Lucas Steffen, Leopoldo Muñoz

Flyrock is one of the most significant hazards associated with blasting in open pit mining, especially for blasting operations near communities. Flyrock can lead to severe injuries, fatalities, and property damage, compromising the license to operate. For this reason, defining exclusion zones is critical to ensure the safety of people and equipment. A very large radius will reduce the risk of flyrock; however, excessive exclusion zones can significantly impact the productivity of the operation and, in some cases, compromise the extraction of ore in critical sectors. Many mine sites use distances derived from pre-established standards, experiences from other mines, or still use simple methods for analysis, like recording blasts with a terrestrial camera and performing deterministic calculations to determine exclusion areas, applying an arbitrarily safety factor for people and equipment. In this paper we present a new approach that allows the calculation of the exclusion zone by measuring critical flyrock parameters with a high degree of accuracy through a new video analytics technology, this data then is used as input to calibrate probabilistic flyrock models to have more robust calculations, allowing optimized and safe exclusion zones. The proposed methodology leverages high-accuracy data and continuous monitoring to dynamically adjust D&B designs and exclusion zones, ensuring maximum safety without unnecessarily restricting operational efficiency. A case study is presented where the application of these new digital technologies allows precise prediction and control of flyrock trajectories, enhancing the accuracy of exclusion zone boundaries. In this case we successfully reduced the exclusion zone radius to 100m, allowing the ore extraction in a critical region close to the community safely. The study shows notable improvements in safety and productivity, including zero flyrock incidents and enhanced protection for nearby communities. The adaptive nature of these digital tools offers scalable solutions for various blasting environments. The paper concludes by recommending the integration of these tools into standard blasting protocols, highlighting the potential for widespread adoption in the industry to mitigate flyrock risks effectively.

Jan 21, 2025

By Cristian Castro, Patricio Gomez, Jason Furtney, Augusto Lucarelli

Understanding the effect of blast-induced damage on wall stability is critical to safe and economical operation of a large open pit mine. In this paper, a numerical modeling methodology is used to investigate damage to rock at distances of greater than 10 m (30 ft) from a blast. Two applications of the model are demonstrated. First, the method is applied at a zinc mine to investigate the effects of pit blasting on underground stopes. The model predictions are compared with the scaled distance formula. Next, the model is used to investigate a common problem in which unfavorable jointing creates a rock wedge on the bench above a blast. The numerical predictions of wedge stability are compared to the wedge energy model described by Wong & Pang (1992).

By Cristian Castro, Patricio Gomez, Jason Furtney, Augusto Lucarelli

Understanding the effect of blast-induced damage on wall stability is critical to safe and economical operation of a large open pit mine. In this paper, a numerical modeling methodology is used to investigate damage to rock at distances of greater than 10 m (30 ft) from a blast. Two applications of the model are demonstrated. First, the method is applied at a zinc mine to investigate the effects of pit blasting on underground stopes. The model predictions are compared with the scaled distance formula. Next, the model is used to investigate a common problem in which unfavorable jointing creates a rock wedge on the bench above a blast. The numerical predictions of wedge stability are compared to the wedge energy model described by Wong & Pang (1992).

Feb 1, 2020

By Steven Townend, Don Wadden

In today's global economy the need to stay competitive is essential for commercial survival and growth. To this end Inco is committed to continuous improvement in its operations. Various aspects of the mining process have been examined to find ways of improvement.

Jan 1, 1994

By Scott G. Giltner, Alex Schwenk

This paper is an update on a paper presented at the 2022 ISEE conference. The original paper presented how the mine operator desired to open up ore reserves near several mine structures including two crushers, the conveyor belt drive and the concentrator thickeners. In order to open up additional ore for extraction (over 3 million long tons or 3 million tonnes) it was necessary to blast out two benches near the mine structures. Since the two benches have been successfully shot, the mine has now conducted nine production blasts in this area at distances as close as 116 m (380 ft) to the two primary crushers. These production blasts are full size production blasts consisting of up to 300 or more blast holes. For these blasts the two primary crushers were still the critical structures as they were the production life blood of the mine. If the crushers were shut down due to any damage from the blasting, the revenue of the mine would be adversely affected. As with the initial bench blasts, two issues provided an extra challenge to the blast design. The first was that the blast holes were still considered large diameter at 12¼ inches (311 mm) and 16 inches (406 mm). The second issue was that the bench heights were short, with the average varying from 34-40 ft (10.3-12.2 m). This combination of large diameter blast holes with a short bench provided an unfavorable geometry for the goals established by the mine management. The mine management established the following goals. 1) None of the mine structures would be damaged by fly-rock. 2) Minimize the blast vibrations at the crushers. 3) The last goal was to produce a muck pile that could be dug easily by hydraulic shovels. Electronic detonators were applied to achieve the necessary control of the blast and optimal fragmentation throughout the mine. UAV surveys of the blast area were also conducted to provide a 3-D representation of the free faces and bench surface. The 3-D point cloud produced from this was used to measure the shape of the free faces. Once the shape of the free faces was quantified, it was possible to establish proper placement of the crest holes and develop a custom explosive load for each blast hole. The results of the nine blasts have provided what the customer requested. The peak vibration level at the crushers for the nine production blasts was 1.6 in/s (40.6 mm/s) at a frequency of 18.9 Hz. There have been no fly-rock or blast vibration issues at any of the nearby mine structures. As a result, the mine has been able to maintain its production with no downtime. The muck piles have been well fragmented with reports from the shovel that they have all dug well.

Jan 21, 2025

By Chris Breeds, Larry Leone, Jerry Wallace

One of the Authors was recently retained to provide a professional engineering analysis of the potential impacts from underwater blasts used to enlarge intake tunnels at the Cheesman Dam near Denver in Colorado and to design Blast Protection Bags that could be installed in each tunnel to protect the 100- year old downstream valve structures.

Jan 1, 2012

By Adam T. Young

This paper will describe the process of using low density bulk emulsion as a means to maximize the production of an oversize or “rip rap” aggregate size range (8 inch to 72 inch) that the quarry customer has a market demand for. It will also discuss the pre-blast and post-blast metrics used during the product trials and evaluation.

Jan 1, 2017

A case history is presented where a variance was permitted by the court to change a 500 foot limit to 250 feet for blasting overburden at a surface coal mine in the proximity of a historic structure.

Jan 1, 1991

By Kirstin Girdner, Vicki Seppala, Tom BoBo, John Kemeny, Mike Higgins

Optimal blast fragmentation is fundamental to all phases of comminution. Changes in blast design may affect efficiency and productivity of downstream processes such as crushing, milling and leaching, resulting in cost savings or losses.

Jan 1, 1999

By William Yutmeyer, Meredith Hardwick

Since 1996 there have been at least two teams formed within the U.S. Government to develop a consistent set of risk-based standards to be used to govern safety. The first of these was the Risk and Lethality Commonality Team which developed risk criteria associated with protecting personnel during launches at the national test ranges. The second team titled the Risk-Based Explosives Safety Criteria Team (RBESCT) is the subject of this paper.

Jan 1, 2007

By Chapman Young, William L. Fourney, Richard D. Dick

During 1981 and 1982, an extensive oil shale fragmentation research program was conducted at the Anvil Points Mine near Rifle, Colorado. The primary goals were to investigate factors involved for adequate fragmentation of oil shale and to evaluate the feasibility of using the modified in situ retort (MIS) method for recovery of oil from oil shale.

Jan 1, 1985

By Alex Jankovich, Darren Thornton, Sarrna Kanchibotla, Cam Grundstrom

The Porgera joint venture and Dyno Noble have commissioned a joint project to optimise the drill and blast operations to increase the overall profitability of the mine. One of the aims of this project is to increase the throughput of semi autogenous (sag) mill by optimising the blast fragmentation, The work done so far clearly indicates that significant improvements in sag mill throughput can be achieved by optimizing the blast fragmentation. This paper discusses the planning, implementation and results achieved so far in this project.

Jan 1, 2001

By P Bellairs

The Hamersley Province is located 1OOOkm to the North of Perth .the Capital City of Western Australia and is of major economic significance due to the mining of extensive deposits of Haematitic Iron Ore for both domestic and export use. A small but significant proportion of the waste associated with these deposits presents problems due to its ability to spontaneously combust and react with explosives resulting in premature detonations.

Jan 1, 1996

By B Mohanty, R Deshaies

Initiation of small diameter explosives by sympathetic shock pressure in water has been investigated under controlled laboratory conditions. Changes either in the geometry of the donor explosive or its point of initiation can alter the essential characteristics (amplitude and duration) of the resulting shock pressure pulse. The pressure signatures from both spherical and cylindrical explosives donors have been studied, in water as well as in various explosive matrices. This paper summarizes the investigations carried out with both 'primed' and 'non-primed' slurry and emulsion explosive matrices with various types of voids. These measurements serve the basis for predicting distances in water for sympathetic initiation for both spherical and linear charges. It is shown that the explosive-detonator system in combination has a far greater probability of initiation due to sympathetic shock pressure than either the explosive or the detonator alone. Various explosive matrices with air bubbles and glass microballoons have been examined and the differing sensitivities to shock pressure explained on the basis of these measurements. It is also concluded that explosives containing air bubbles instead of microballoons would be significantly more prone to sympathetic initiation.

Jan 1, 1992

By B R. Spencer

Using bulk repumpable water gel explosives in underwater shooting results in even more benefits to the user than a "dryland" customer. It is nearly impossible to reshoot underwater, so a bad shot causes tremendous problems. The huge expense of operating drill boats, dredging buckets and clamshells makes shot loading, hookup and digging cycle times critically important.

Jan 1, 1990

By Jim Hall, Denis Rickman, Jon Windham, John Ehrgott, Stephen Akers, Byron Armstrong

With the growing concerns about terrorism world-wide, numerous agencies conduct experiments to investigate the effects of terrorist vehicle bombs. In many cases, the vehicle bomb of interest utilizes some form of ammonium nitrate/fuel oil (ANFO) as the explosive source. Due to the high cost of fullscale testing, it is advantageous to conduct at least some vehicle bomb experiments at reduced scale. Extensive testing has shown that ANFO is a non-ideal explosive, and its explosive output does not scale reliably at explosive masses below approximately 400 lb (182 kg). Most scale-model testing requires explosive masses 1 to 5 orders of magnitude smaller. Thus, scale-model testing is typically conducted with “ideal” explosives, such as composition C-4, which perform in a scalable manner at virtually any charge mass. The utilization of an ideal explosive to model ANFO requires the existence of an accurate means of equating the performance of the two explosives. The airblast equivalence of C-4 and ANFO has been well established. However, the cratering equivalence of these explosives is not thoroughly quantified. This is especially true for the case of an above-ground detonation, which is precisely the scenario of interest in vehicle bomb studies. A study has been conducted to better define the cratering equivalence of C-4 and ANFO for above-ground detonations. This paper presents a discussion of results from this research.

Jan 1, 2008

By Doug Wathen, Philip M. E Thomas

The City of Fort Myers needed to replace a 40-year old 42-inch storm sewer line in downtown Fort Myers with a new 54-inch line to accommodate population growth. The old line had to be kept operational while a new line was installed. the contractor spent two months using a drop ball, a hoe ram, and large rippers trying to break the three to four feet of rock that needed to be removed to accommodate the new pipe. Mechanical trenching was considered but was proven to be overly expensive. On very short notice, Ireco of Florida was asked to design and execute a blasting procedure that would allow this project to proceed. Nearby buildings were over 80 years old, three of them containing antique shops specializing in glass antiquities with attorney offices above them. High water table compounded problems with a 20-year old steel water main and clay drainage pipe 15 feet from the new sewer line. Holes had to be drilled within six inches of the edge of the existing pipe to four feet below the pipe on either side of the pipe and blasted. No interruption in the sewer line flow was to be tolerated.

Jan 1, 1996

Investigating blast vibrations typically utilises scaling and attenuation models for prediction of vibration amplitude over a range of charge weights and distances. A number of generalised relationships have been established from many years of far-field data analysis, where small changes in charge weight and ray-path distance are less critical. Under far-field conditions, small variations in local geology or geometry do not significantly affect the vibration scaling behaviour over an expected range of data. In the near to intermediate-field (less than 5 times the explosive charge length), small variations in wavepath and rock mass conditions between a blast and a monitoring point can greatly affect the outcome of vibration modelling. This case is especially true for underground blasting in sublevel open stoping, where the paths of blast-induced vibrations regularly encounter voids and preconditioned ground.

Jan 1, 2010

By Timothy D. Stark

Blasters are usually strictly liable for injury or damage caused by flyrock (trespassory invasion) and blast-induced vibrations (non-trespassory invasion). The application of strict liability to non-trespassory invasions has resulted in significant litigation that has hampered the use of blasting and the blasting industry. Stark (2002) proposes that blasters should not be held strictly liable for non-trespassory invasions but should be liable only if their conduct is proven to be negligent. This change in legal standard was proposed because improvements in blasting technology over the last thirty years allow blasting to be conducted without substantial risk of harm to property and thus the amount of harm imposed by a blast can be related to the level of care exercised by the blaster. It is anticipated that negligence standard will reduce the amount of litigation because a plaintiff will have a greater burden to overcome. To facilitate the acceptance of negligence standard by a court of law, this paper illustrates the application of the negligence and strict tort liability frameworks using actual cases in which a decision was rendered. It is evident from these cases that some of the successful claims under the strict liability framework would not have been successful, and probably not litigated, under a negligence framework, which could result in substantial cost savings to the blasting industry and consumers.

Jan 1, 2004