Search Documents

By Jeffrey E. Loney, Andrew F. McKnown

Recovery of contaminated groundwater migrating through bedrock can be very difficult due to the low transmissivity of many bedrock fracture systems. To overcome these difficulties, a system of controlled "trench" blasting has been used on several projects to assist in cutting off and collecting groundwater plumes in bedrock. By using a combination of trench blasting and presplitting techniques, linear "fracture" zones are created in appropriate locations to significantly increase flow into recovery wells and control plume migration.

Jan 1, 1995

By Lindsay Wade, Peter Dare-Bryan

Benches in surface mines often contain known areas of ore and known areas of waste, which must be mined selectively. When rock is blasted it not only fragments but is also physically, and non-uniformly, moved. Risks therefore exist of ore being lost if treated as waste and of mill feed being diluted by waste. Both possibilities carry serious fmancial implications.

Jan 1, 2001

By Norman S. Smith, Richard L. Ash

Relationships between the three design factors of borehole burden, spacing, and length that control rock breakage were examined by means of reduced-scale bench blasts in dolomite. A set of three indices were developed for analyzing the differences between fragment-sizing distributions obtained from various design combinations. It was found that the factors were interdependent and the indices were directly related to the common stiffness relationship for solid structures. The burden-spacing-length combinations that produced the best and poorest overall breakage, maximum and minimum overbreak, and least and most toe were determined.

Jan 1, 1977

By Qingshou Chen, Paul N. Worsey

It has been recently argued that rock strength has little effect on the final results of pre-split blasting and is of only minor importance when blasting rock in general. However, it can be shown that the maximum borehole separation for optimal perimeter blasting results with constant borehole and loading configuration is strongly dependent on the tensile strength of the rock.

Jan 1, 1986

By S A. Steyn, I P. Douglas

Duvha Opencast is a large South African dragline operation supplying coal to the Duvha Power Station which is operated by Eskom, the state power utility. For Duvha to remain competitive with other collieries, it has proved necessary to continuously examine and investigate methods of reducing costs. With explosives representing a major portion of the total working costs, blasting is an obvious area of investigation.

Jan 1, 1991

By Joseph A. Sohara, John J. Mullay, Curtis J. Keefer, Robert L. Schrepple

The desensitization of an explosive column by the action of a previous detonation (adjacent borehole, deck or detonating cord) is a vital concern to the explosives industry. Previous reports to this symposium and in other places have addressed this issue. However, this work has been mainly concerned with model or simulated conditions. No systematic study has appeared that utilizes an actual borehole environment. Thus the relation between this work and expected field performance is somewhat uncertain. The present paper attempts to partially resolve this difficulty.

Jan 1, 1990

By Kenneth Eltschlager

Post-blast assessment techniques using off-site data which includes location, seismograph and photographic data were discussed during the Blaster’s Weekend at this year’s ISEE Conference. Blast and property locations with commonly available GPS units allow for the spatial relationships surrounding the blasting to be documented. When distances are coupled with the charge weight per delay, the scaled distance can be calculated to any structure for either compliance with the rules, or to project limitations. When blasting seismograph data is obtained, the scaled distances are then able to be plotted against ground and air vibration levels for post-blast assessment purposes.

Jan 1, 2007

By Raymond M. Dixon, Dale L. Ramsey

Upon being introduced to the MAGNETIC COUPLING concept,Balsinger,Inc. wanted to conduct field trials to explore the potential of Magnetic Coupling in the U.S.. Although the Magnetic Coupling Concept has been widely used, the U.S. proposed blasting criterion not previously addressed by the system. Modification to the system assembly and blasting accessories had to be made to make the system adaptable to our specific requirements. The field trials and system modifications are the basis of this paper.

Jan 1, 1990

By J P. F Warkentin, A W. Bauer

Recently, significant improvements have been made in both blast design methods and blasting accessories. The introduction of extremely accurate blast delays now allows proper implementation of advanced blast designs. Thus the onus for future blasting improvements has moved from blast design to the need for ensuring that explosives quality is of the highest order. One measurement commonly used to assess explosive performance is the velocity of detonation (VOD).

Jan 1, 1991

By G Alan Foster

The presence of approximately 600,000 attorneys in the U.S.A. and the determination by the courts that blasting is considered an 'ultra hazardous' activity makes every practical blaster aware that at some time during his working life he will probably be faced with defending himself in court.

Jan 1, 1982

Increasingly specialized blasting needs require that the explosive energy available in a borehole be reliably known for representative blasting conditions. The underwater test, when properly performed, can yield such information and thus provide a reliable rating of explosives in terms of energy release. This paper reiterates the stringent experimental conditions to be satisfied, and data analysis and interpretation techniques to be followed to achieve this. This is supported by detailed experimental studies involving select parameters in both detonator and booster sensitive explosive compositions. The paper also illustrates the inadvisability of equating blasting performance with the commonly calculated energy values.

Jan 1, 2000

By Lewis L. Oriard

This paper describes the process of developing blasting specifications for 850 miles of new pipe trench running parallel to an existing high-pressure gas pipeline, often with as little as 14 ft to the existing pipeline trench. The primary method of preventing damage to the existing pipeline was the use of fracture (overbreak) control.

Jan 1, 1994

By Thomas L. Barkley, Michael A. Indihar

The new Cyprus Northshore Mining Co. has taken the previous blasting methods of Reserve Mining Co.'s mine in northern Minnesota and adapted them to a new competative Iron Ore Industry. Cyprus was challenged to develop new blasting methods to reduce costs and improve results over the previous mining operation. Many of the older procedures have been kept, but others have been changed in ways that bring the mine operation up to state of the art technology. In addition, unique ideas not previously tried in the North American Iron Ore Industry have been instituted. So far, this has reduced Cyprus's blasting costs by 70 percent.

Jan 1, 1991

By Ettore Contestabile, Cameron Thomas

Implosive-type electrical/mechanical connectors such as XECONEX have been used extensively for joining electrical transmission lines. This implosive action of explosives has also been applied to other forms of high energy metal working with excellent results. However, as with many other products, the inherent blast energy of these units has caused some environmental concerns especially when used in proximity to inhabited areas.

Jan 1, 1995

By Mark S. Stagg, Rolfe E. Otterness, Stephen Rholl

The Bureau of Mines is engaged in research to develop and test high explosive fracturing and rubblization techniques that will enhance ore body permeability and thus increase recovery during in situ mining. The natural permeability of many ore bodies is too low to allow successful in-place leaching. These deposits could be profitably mined if flow rates of leach solutions could be increased. Blasting represents a potentially low-cost and effective permeability enhancement technique.

Jan 1, 1991

By D. Bartley, R. McClure, W. Reisz

Ever since the 8ms criterion was developed in the early 60’s there has been an ongoing debate among many blasters as to its actual value in controlling ground vibration. The perpetuation of the myth surrounding the 8ms window can be partly attributed to its simplicity and convenience as a means for regulatory compliance. Unfortunately, the mindset that many blasters have adopted has hindered the development and use of more effective techniques and in many cases can actually be counter productive to vibration control.

Jan 1, 2006

Current research in comminution includes efforts to increase the efficiency of mineral processing systems and reduce the amount of electrical energy needed for size reduction. In most mining operations, comminution begins with blasting. Normally, blast design focuses on loosening material for excavation and sizing the product for efficient haulage. It is likely that blasting also results in internal damage to rock fragments within the blast pattern which may provide subsequent comminution benefits. If substantial comminution benefits exist, appropriate modification to blast pattern design may reduce the overall electrical energy needed for mineral liberation.

Jan 1, 1996

By D E. Siskind

The Bureau of Mines performed a comparative study of nine sites at eight surface coal mines to determine if the presence of near-surfaced underground abandoned workings resulted in the generation of adverse long-duration, low-frequency blast vibrations. Six of the nine sites had underlying workings, and two had thick layers of low-velocity unconsolidated surface material.

Jan 1, 1990

By Richard Arsenault

The production of oil & gas from wells requires method of flow from the producing formation into the well bore. Once the well is drilled it will have casing pipe installed to protect the integrity of the well formations and means of delivery to the surface. Once casing pipe is installed it will be cemented in by pumping cement through the annulus of the casing pipe down to the bottom of the well and allowed to flow outside the casing pipe up into the formation.

Jan 1, 2007

By C A. "Hawk" Hanger

"The paper that will be presented is an in-depth study of sequential blasting using standardnon-electric shock tube down hole timing along with surface M.S. connector timing.Included also will be a discussion on the advantages in fragmentation, digability, oredilution' and ground vibration versus the common practice of row by row blasting. Alongwith the written presentation, several visual illustrations will be included. The visuals willrefine the actual direction and predicted movement of the shot involved."

Jan 1, 1993