Search Documents

By Gabriel Aguilera, Juan Arismendy

"As a separator machine, the hydrocyclone is one of the most commonly used equipment in different types of industries and particularly in mineral processing, hydrodynamic behavior allows efficient separation, but developing tests to optimize experimental equipment is expensive, therefore Computational Fluid dynamics (CFD) becomes a useful tool for optimizing the geometrical and operational parameters, and allows to analyze and understand the dynamics within the equipment. In the research was developed to simulate of 40 mm hydrocyclone where turbulence model was used Large Eddy Simulation (LES) for the continuous phase, for the generation of the air core and for the interaction of particles at low concentrations was implemented (mixture model), after the simulation was completed validation and comparation was done between simulation values and experimental."

Jan 1, 2014

By Massimiliano Zanin, William Skinner, Owusu Clement, Jonas Addai-Mensah, Daniel Fornasiero

This paper highlights the importance of pulp aeration in the selective separation of chalcopyrite from chalcopyrite/pyrite mixtures of varying pyrite content (20-80 wt.%). Laboratory batch flotation studies and oxygen demand tests were performed to predict the optimum amount of air required for the selective separation of chalcopyrite from pyrite. The pulp oxygen demand was shown to increase with increasing pyrite content but decrease with time as more air is introduced into the system. Complementary batch flotation tests showed significant improvement in chalcopyrite flotation under moderate pre-aeration of the pulp. However, a continuous decrease of chalcopyrite flotation was observed under highly aerated conditions. The amount of air required to achieve maximum chalcopyrite flotation recovery correlated positively with the mass fraction of pyrite in the pulps. The greater the wt.% of pyrite in the chalcopyrite/pyrite pulp, the longer the aeration time required. The optimum aeration time was established as the time before which the oxygen consumption rate constant reaches a bottom plateau. Surface analysis (XPS) indicated that the continuous decrease in pyrite recovery observed with increasing aeration time was due to the formation of more iron oxy/hydroxide on its surfaces, the same species accounting for the decrease in Cp recovery after prolonged aeration.

Jan 1, 2014

By M. Ito

Cobalt-rich ferromanganese crust and nodule ores from seamount areas contain volcanic and sedimentary rocks as substrate or nuclei and these ores require mineral processing to remove the substrate/nuclei rock before smelting. This paper reviews the results of jig separation and air table treatment for the coarse fraction and flotation and hybrid jigging for the fine fraction. Using these techniques substrate/nuclei rock was removed from the cobalt-rich ferromanganese oxide components. The mineralogical properties and metallurgical treatment methods including hydrometallurgical treatment of low grade ore is also reviewed.

Sep 1, 2012

By Xumeng Chen, Yongjun Peng, Dee Bradshaw

Regrinding rougher flotation concentrates has become a common practice when processing low grade and complex ores. It not only reduces the particle size and improves mineral liberation but also modifies particle surfaces and pulp chemistry due to the strong electrochemical reactions taking place during regrinding. Therefore, the floatability of minerals in the subsequent cleaner flotation is influenced by the regrinding conditions. This paper presents the effect of regrinding conditions on the mineral floatability from both industrial studies in the plant and fundamental studies in the laboratory. Different regrinding conditions were considered, including grinding media, the electrochemical properties of minerals, pulp chemistry (pH, Eh, DO), and breakage mechanisms in tumbling and stirred mills. Results indicate that the selection of regrinding conditions and mill types should not only depend on grinding energy efficiency and liberation but also depend on the surface properties and pulp chemistry produced for effective mineral flotation and separation at the cleaner stage.

Jan 1, 2014

Under the AMIRA P9 project the three-product cyclone-an off-shoot of the conventional hydro-cyclone-that produces three distinct products has been developed. The three-product cyclone shows great promise as a classifier in mineral processing. Industrial and pilot plant trials performed to assess its performance in the classification of the UG2 platinum ore, indicate that the presence of an extra overflow product stream that captures the mid-sized particles, provides improved classification efficiency. To assess the split on component density, samples from the feed and product streams were screened and assays by size for chromite (? = 4.8) and silica (? = 2.65) were obtained. Results from tests performed using this type of hydrocyclone in a number of applications indicates that it can be applied successfully in circuit configurations where the conventional hydrocyc-lone is not suitable. Utilising the three-product cyclone to classify the UG2 platinum ore resulted in an intermediate overflow product stream containing the mid-sized low density silicates and relatively fine high density chromite particles while the finer overflow contained mostly fine silicates and chromite particles. The coarse chromite and silicates reported to the underflow. Due to the increased number of products, the method of using efficiency curves was extended to cater for the increased number of products in the three-product cyclone. Although significant differences in the classification performance of the three-product cyclone were noticed with variations in machine variables a consistent method of assessing the performance was applied. The efficiency curve was adopted and applied and separate efficiency curve properties were obtained for each product stream. The methodology was applied to the component data, and efficiency curve proper-ties for each key component were obtained and compared. This paper discusses the application of the efficiency curve to cyclones producing more than two products and extending the methodology to the different components in the feed.

Jan 1, 2014

By N. I. Tyushkova

On the basis of detailed studying of mineral structure of ore and treatment products it is established that the given ore refers to oxidized Pb-Zn vein-disseminated ores. Technological special features of the basic ore minerals and the reasons causing their obstinateness that is defined by following features are revealed, presence at dominating quantity difficult to float lead minerals: mimetesite (9.67%), green lead ore(0.48%); non float: bindheimite (2.16%) and plumbojarosite (0.36%) and high assay of oxides and hydrous ferric oxides; also thin, emulsive and submicroscopic segregations of the defined minerals in swamp ore. As a result of researches the scheme of gravitational-flotation treatment was conducted in semi-industrial scale. It allows to receive two concentrates from ore: a lead gravitational concentrate of mark ??-4 with the assay of 55.5 % of Pb and 0.77 % of Zn; and a Pb concentrate of mark ??-7 with assay of Pb of 40.97 % and Zn of 1.39 %. The total assay of Pb in concentrates makes 81 %. The efficiency offered by gravitational-flotation schemes is defined by possibility for recovery of big impregnated lead minerals under gravitation. The use of this method of gravitation has allowed to recover such mineral as beudantide and to exclude irrevocable losses of lead in tails which are connected with this mineral. Scientific value of the presented researches is connected with the fact the problem of extraction of the oxidized minerals of Bb and Zn is rather difficult and insufficiently studied. Keywords: flotation, oxidized forms of Pb and Zn

Sep 1, 2012

By J. C. van Dyk

In a previous study by Van Dyk, et al., (2006) and Van Dyk et al. (2006), a FactSage model was developed to understand the chemistry and interpret mineral matter transformation during a fixed bed counter-current gasification process. It was concluded that the FactSage model developed, compared with HT-XRD experimental results and that the FactSage thermodynamic modeling sup-plies insight into specific mineral reactions and slag formation. The specific value for Sasol in using FactSage, in combination with HT-XRD is that it can be used to analyze equilibrium conditions for reactions occurring between inorganic and organic materials together, as well as to provide insight into mineral transformation and slag formation. The purpose of the present study was to improve the current FactSage modeling approach, by combining specific zones in the gasification process. This can improve and speed-up the interpretation of mineral matter transformations and flow properties of reacted mineral matter in coal and assist in identifying and quantifying slag formation in the gasifier operation at temperatures not reflected by normal AFT analyses. The updated and improved FactSage model compared favorably with the original model as well as with HT-XRD results and thus will be able to supply results in a faster and more convenient manner. In the new FactSage model, supported by HT-XRD experimental findings, it is indicated that feldspar formation (including anorthite) correlated with slag formation at temperatures around 1000°C and no slag formation in the base case coal was observed in the drying and devolitilization zone, as was to be expected. Feldspar is one is the mineral species which has the lowest AFT causing the most slag-liquid formation and forms probably as a product between the SiO2, Al2O3 and Ca-containing species. In the gasification zone it was clear that slag-liquid formed at a temperature of 1000°C, with a decrease in the feldspar content. Mullite formation was also observed in the base case sample in the temperature range 1000°C and 1100°C. The decrease in the amount of SiO2 at 1100°C is related to the formation of mullite, but also that the slag-liquid phase also contains an amount of SiO2 in the molten form.

Jan 1, 2014

By K. Haga

In this study, flotation tests were performed to investigate behavior of enargite and chalcopyrite ores from different sources synthetically mixed for separation of enargite. Flotation parameters including; pH, reagents concentration and type and flotation time were controlled to obtain an enargite concentrate with high As and chalcopyrite concentrate and final tailings with As content below 0.5 mass%. The copper ore bearing enargite mineral contained 5.87 mass% As and 16.50 mass% Cu while the chalcopyrite bearing ore contained 0.32 mass% As and 21.63 mass% Cu. The two ore samples were mixed at 7:3 (enargite: chalcopyrite) by weight ratio to prepare a mixed ore sample with arsenic content at 3.16 mass% and 18.25 mass% Cu for the flotation study. For enargite single ore flotation, the 38?75 µm size fraction showed that over 98% enargite was selectively recovered within 5 min at slurry pH of 4.0 and arsenic content in the final tailings was reduced to 0.22 mass%. In mix ore (enargite+chalcopyrite) flotation, 97% of enargite was first removed at pH 4 followed by chalcopyrite flotation at pH 8, and over 95% recovery was achieved in 15 min flotation time. Arsenic content in the final tailings was reduced to 0.1 mass%.

Sep 1, 2012

By V. V. Morozov, I. S. Barmin, A. V. Tugolukov, V. V. Polivanskaya

"It was presents the results of research on improving reagent regime and scheme of enrichment of slime classes of Apatite-Staffelite ores and tailings stockpile of Kovdorsky enrichment plant. It was investigated the regularities of flocculation in the processes of thickening and selective flotation apatite-bearing ores. It was established character of the influence of flotation reagents on the flocculation process. It was shown that the sodium silicate and soda ash have a stabilizing effect by thickening of sludges. Neonol and oleic acid have a coagulating or flocculating effect. It was tested the new regime flotation, involving an initial conditioning with using of reagent - dispersants before feeding the pulp into the flotation and subsequent conditioning with reagents having a coagulating effect. The flowsheet and reagent regime for enrichment of fine-grained tailings stockpiled was developed, which providing production of standard apatite concentrate and increasing the recovery of valuable components. There are presented results of the research of activities of strong organic surfactant on solubility of colloidal form fatty acid collector and aggregate stability of fine minerals in the process of thickening and flotation. Surfactants such as Neonol have been investigated for increasing the activity of the collectors. When using the process of thickening sludge fraction with flocculant Praestol 2540 and stadial conditioning of sludge were obtained concentrates containing up to 38.1% P2O5 at recovery. INTRODUCTION A feature of the Apatite-Staffelite ores of the Kovdorsky deposit is the presence of a large number of fine mineral particles and a reduced hardness of phosphate minerals (Beloborodov et al., 2010, Tugolukov et al., 2012). Formed in the ore-preparation process, sludges are lost with a discharge in the thickening operation. Sludge is characterized by an increased content of phosphorus pentoxide (P2O5). Losses of P2O5 at enrichment of the stale tailings of Kovdorsky GOK reach 14.0%. The high losses of P2O5 caused a profound study of the behavior of thin apatite classes under conditions of thickening and flotation."

Jan 1, 2018

By S. Serranti

The recycling of end-of-life concrete into new concrete is one of the most interesting options for reducing worldwide natural resources use and emissions associated with the building materials sector. The possibility to realize a larger re-use of silica aggregates from old concrete, strongly contributes to reduce environmental impact (reduced exploitation of natural resources, reduction of CO2 emissions, airborne dust production, etc.).To reach this goal, innovative processing techniques, as well as innovative sensing units and architectures have to be developed. In this perspective an analytical approach, based on hyperspectral sensing techniques, is proposed, discussed and critically evaluated in order to perform an automatic quality control assessment, finalized to maintain a high standard of concrete demolition waste, from the earliest stage of recycling to the further processing stages, according to the detected in-situ demolition waste characteristics. The paper deals with the analysis and the evaluation of the problems related to the integration of this approach with state-of-the-art demolition and building processes and procedures. Keywords: end-of-life concrete, recycling, hyperspectral imaging, NIR spectroscopy, quality control

Sep 1, 2012

By P. Radziszewski

In comminution research, ore breakage and wear are usually studied independently of one another. Much of this is due to the fact that wear is usually a slow process compared to ore kage. However, the abrasion wheel test used to determine the abrasive wear contribution to total steel media wear provides the opportunity to study not only abrasive wear and friction but also ore breakage. In this paper, we will explore the use of the abrasion wheel wear test device to study abrasive wear, friction and ore breakage using standard Ottawa foundry sand. We will look into the feasibility of applying the work index as well as t10methodologies to this test set-up. We will also look at how the work index results evolve with abrasive wear and friction. We will then discuss the merits of pursuing the use of this abrasion wheel test for not only wear characterization but also breakage characterization.

Jan 1, 2014

Mineral processing is an energy and water intensive activity. Mill comminution equipment usually has high energy requirements which necessitate extensive cooling to remove heat. Cooling requirements are typically 10% to 20% of the comminution energy. If there is an adequate supply of suitable water, open water-based cooling systems are the simplest, cheapest and most energy efficient cooling method available. This paper describes a method to determine the water demand for open water-based cooling systems at a plant and to determine whether the mine has sufficient water to meet that demand.

Jan 1, 2014

By P. Fawell, C. Castillo, C. Ihle

"The need to reduce fresh water consumption has pushed many Chilean mining companies to utilize seawater obtained from distant locations. At the same time, increasing amounts of fine particles in copper tailings raise new operational challenges, in particular, the thickening and transport of tailings featuring significant fine fractions, which are predominantly clays. In the present paper, we study the role of salinity – using seawater and NaCl – on the flocculation efficiency of copper sulphide tailings to which kaolinite was added. To mimic the water recovery stage in thickeners, flocculation has been induced in jar tests and the corresponding aggregate size distribution has been estimated from chord length distribution data obtained using a focused beam reflectance measurement (FBRM) probe, at various mean turbulence intensities. Results show that for constant flocculant dosing, a measurable influence of the salt on the resulting aggregation exists. For each case, resulting optimal turbulence levels are also reported, a particularly interesting feature when comparing flocculation efficiency of the coarse and fine fraction. INTRODUCTION The concentration of copper minerals through comminution and flotation is intensive in the use of fresh water. The need to reduce the consumption of fresh water and the environmental standards associated with increasingly demanding mining operations have driven improvements in the techniques of recovering water from tailings. The challenges are even greater when required to treat minerals with high clay contents. In Chile, kaolinite is one of the most important clays to consider due to its abundance in the tailings from many operations. The most common and highest throughput unit operation in the mining industry for the recovery of water from tailings is gravity thickening, with sedimentation of fine particles assisted by flocculation. Flocculation is the process of forming aggregates by contacting the suspended particles with a flocculant. The flocculant is typically a water-soluble synthetic long-chain polymer, where copolymers of acrylamide and sodium acrylate are the most common types used in the Chilean mining industry. The aggregation mechanism includes the following key steps: (1) flocculant distribution through the suspended particles, (2) flocculant adsorption onto particle surfaces, and (3) collisions between particles leading to polymer bridging to form aggregates, but concurrently (4) breakage of aggregates becomes a factor under prolonged shear (Gregory, 1988)."

Jan 1, 2018

By B. McFadzean, P. E. Ngoepe, P. P. Mkhonto, J. Taguta

The adsorption of heterocyclic collectors such 2-mercaptobenzothiazole (MBT), 2-mercaptobenzoxazole (MBO), 2-mercaptobenzimidazole (MBI) and their derivatives on pyrite form a basis in understanding the flotation reactivity that may be applicable in a wide range of sulphide minerals. This study uses a computational and experimental approach to determine the heat of adsorption of MBT, MBO, MBI and modified MBT collectors onto pyrite surfaces. Computational calculations found that the adsorption energies were in the order: MBO > MBI > MBT. The heterocyclic collectors were adsorbed in their thiolate form on the surface. In the case of the pyrite (100) surface, the MBT adsorbed through the exocyclic sulphur atom, while MBO and MBI adsorbed through the exocyclic sulphur and N atoms onto the 5-coordinated Fe atom. The (111) surface was found to be more reactive and different adsorption mechanisms were predicted, where the MBT exocyclic sulphur atom bridged on the 5- coordinated Fe and surface 2-coordinated sulphur atoms, while the N atom adsorbed on the 5-coordinated Fe atom. In the case of MBO and MBI, dissociation of the exocyclic sulphur atom from the collector occurred with subsequent interaction with the surface 5-cordinated Fe and 2-coordinated S atoms. This resulted in the collector carbon atom adsorbing on the surface 2-coordinated S atom, while the N atom adsorbed on the 5-coordinated Fe atom. The adsorption of the modified MBT was found to be more exothermic than the MBT, which showed that introduction of a –CS2 group on the exocyclic sulphur atom improved the affinity of MBT on the surface, and was thus a better flotation collector. The computational results were supported by experimental enthalpy of adsorption measurements and microflotation tests. The chemistry of the heterocyclic thioamides is complicated by the fact that they can exist in a number of tautomeric and ionic forms at different pH’s. This is discussed in relation to the flotation and calorimetric data.

Jan 1, 2018

By Masanori Mori, Hajime Miki, Osamu Ichikawa, Tsuyoshi Hirajima, Mitsuru Sawada, Keiko Sasaki

For pretreatment of selective flotation, surface oxidation of chalcopyrite and molybdenite was applied by oxygen plasma then the minerals were washed by solution at pH 9 with oxygen bubbling. Surface characteristics of these minerals were investigated with AFM, XPS, zeta potential and contact angle measurements. Contact angle of chalcopyrite and molybdenite decreased a lot by plasma treatment. When they were washed with pH 9 solution with oxygen bubbling, contact angle of molybdenite increased whereas chalcopyrite one kept low. Adhesion force measurements indicated similar behavior. Result of flotation experiments indicated low recovery of both chalcopyrite and molybdenite after plasma treatment and only molybdenite recovery became higher after washing. Selective flotation of chalcopyrite and molybdenite could be achieved with this process. Possible mechanism of selective flotation was proposed from the results of XPS, AFM, etc.

Jan 1, 2014

By Seher Ata

This paper is concerned with the coalescence behaviour of two bubbles in dilute solutions of cetyltrimethylammonium bromide, methyl isobutyl carbonil and triton x-100. Two bubbles were produced at the tips of adjacent capillaries and the time elapsed between the first contact of the bubbles and film rupture was determined by means of a high speed camera. It was found that the amount of surfactant required to stabilise the bubbles increased in order of CTAB>TX-100>MIBC. The probability of coalescence decreased sharply with increasing surfactant concentration in CTAB and TX-100 solutions while with MIBC each bubble pairs resulted in coalescence, giving hundred per-cent coalescence probability.

Jan 1, 2014

By Brabcova Z.

This contribution deals with bubble adhesion on particle surface which consists of three steps ? the liquid film thinning, the film rupture and expansion of the three phase contact (TPC). Our attention is devoted to the third step ? to the description of the TPC expansion. Three-phase contact line expansion can be theoretically described using hydrodynamic and molecular-kinetic models. Both of these models were originally developed for the interaction of the bubble with horizontal plane in pure water. Our experiments deal mainly with the interaction of the bubble with the inclined plane in the solution of surface active agents. It was proved experimentally that molecular-kinetic model corresponds also to these conditions and this model was used for the description of the TPC expansion. The model is based on the theoretical description of the bubble contact angle on the three-phase interface. These contact angles change dramatically from 180o to equilibium (Young) contact angle close to 90o. Modificated ADSA method is used for the calculation of the contact angle. This method utilizes the Laplace equation of the capillarity; the bubble profile and the contact angle are evaluated using the set of experimental points around the edge of the bubble. The comparison of the experimental and calculated bubble profile shows a good agreement. The aim of the project is to describe the process of the TPC expansion during the adhesion of the bubble with the diameter up to 1 mm. Inclined planes were used instead of an experimental solid particle. Our experiments were provided in the solution of surface active compounds. The process of the adhesion was recorded using high-speed digital camera and images were evaluated using the image analysis software NIS-Elements. Calculations were performed using the MATLAB software. Keywords: bubble-particle interaction, adhesion, three-phase contact, contact angle

Sep 1, 2012

By Lucy van de Ruit, Megan Becker, Aubrey Mainza, Jenny Wiese

"UG2 chromitite ore is a complex, highly disseminated platinum ore from the Bushveld Complex in South Africa, with typical platinum group mineral (PGM) grain sizes below 15µm. The introduction of stirred mills to the platinum industry has enabled grinding to finer product sizes, which has improved liberation and recovery of the finely grained PGMs. However, reduction in particle size leads to an increase in chromite entrainment in the flotation concentrate, which has a negative impact on the subsequent smelting process. Factors such as particle size, froth structure, solids concentration and water recovery have all been identified as impacting entrainment, but whether particle shape also has a significant effect is unclear. The purpose of this study was to determine whether the recovery of chromite particles by entrainment during the flotation of UG2 ore is affected by particle morphology. A laboratory vertical stirred mill with inert ceramic media was used for grinding UG2 ore which was then floated in a batch flotation cell. Flotation feed and concentrate samples were analyzed using QEMSCAN to quantify the angularity and aspect ratio distributions of the particles. The stirred mill product was found to have relatively broad aspect ratio and angularity distributions, with the major mineral components (chromite and silicates) having very similar shape characteristics. Analysis of flotation feed and concentrate samples suggested that particle shape does not have a significant effect on chromite entrainment."

Jan 1, 2014

By M. E. Holuszko

This paper reports the results of induction time measurements carried out on the products of film flotation of galena and sphalerite particles from three different size fractions (38~75µm; 75~150µm; 150~212µm). As expected, the tailings (sinking fraction) from film flotation at any particular surface tension, had always longer induction times than the concentrates (floating fraction), for both minerals. The difference between the induction times of film flotation concentrate and tailings could be as little as 2.5 ms and 5 ms, and as large as 6 ms and 10 ms. These differences can be related to the different hydrophobic characteristics of these fractions, as expressed by (?c) and composition of the particular film flotation product. In addition, the induction times of the larger particle size fraction were shown to be longer than for the corresponding smaller particle size fraction, even though the average ?c(degree of hydro-phobicity) of these fractions appears to be very similar. Desliming, Cu activation and collector addition to the sphalerite samples was shown to decrease the induction time values significantly.

Jan 1, 2014

By Sanja Miskovic, Manjunath Basavarajappa

In this study, a coupled CFD-DEM (Computational Fluid Dynamics-Discrete Element Method) approach is used to simulate two-phase, solid-liquid flow within the flotation cell. Turbulence plays a key role in flotation cells and level of turbulence is affected locally by the presence of particles. Turbulence in the flow is modelled using Reynolds Averaged Navier-Stokes (RANS) based k-e model. Using particle transport and spatial distribution, mixing mechanism for differed sized particles are analysed. By including the effects of particle-particle collision, particle rotation, and particle translation, as well as the volume occupied by the particles in the fluid, CFD-DEM approach can be used to accurately predict the motion of particles in the turbulent solid-liquid flows with strong coupling. Electrical resistance tomography (ERT) is used to investigate the effect of impeller size, shape, off-bottom clearance and impeller speed on mixing and suspension behaviour inside flotation cell. The effect of flotation impeller design, impeller size, and off-bottom clearance on flow hydrodynamics is investigated. In the case of moderate and high solids loading (> 10 %w/w), energy is dissipated through inter-particle interactions and four-way coupling becomes important (Derksen 2003). The main goal of this study is to understand the effect of particle size and concentration on flow dynamics at high Re in highly turbulent systems using advanced modelling and measurement techniques. Experimental measurements obtained by ERT) system allowed detailed mapping of temporal hold-up profiles of the dispersed phase. Impeller size and off-bottom clearance are found have significant effect on the particle suspension characteristics.

Jan 1, 2014