Search Documents

Domestic production of pyrite cinder reached 15.95 million tons in 2006. The pyrite cinder used in cement industry accounts for about 30% production. The remaining 70%, 11.17 million tons, was thrown away as waste, which brought serious environmental and resource problems. A new technology of composite pellet reduction-roasting and magnetic-separation (CPRM) has been developed to utilize pyrite cinder. Pyrite cinder sample, containing 45.56% Fe, 0.19% Cu and 1.45% S, was pelletized with addition of 5% composite agent in balling disc. Green balls after drying were reduced at 700~800 ? for 20min with 300kg/t pulverized coal injection in rotary kiln. After two stages of ball-grinding and four stages of magnetic separation, high grade magnetite concentrate with 66.23% Fe was produced, meanwhile impurities Cu and S was decreased to 0.048% and 0.053%, respectively. And iron recovery of 73.32%, desulphurization of 96.34% and decoppering degree of 74.73% were achieved. Key technique is that composite agent can accelerate reduction of Fe2O3 and transfer copper and sulphur into water-soluble inorganic salts, which can be removed during wet magnetic concentration. This new technology can be used to fully utilize pyrite cinder and produce high quality magnetite concentrates as feed for steel industry, which will help tackle the pollution problem of pyrite cinder and extend iron-bearing raw material sourcing for Chinese steel industry.

Jan 1, 2014

By Ö. Genç

In this paper, full-scale mill data collected from three different circuit configurations in cement plants demonstrated the size reduction performance of dry ball mills in relation with the ball size classification achieved by the classifying liners used in the grinding compartments. Findings indicated that, breakage rates at the last 2 ~ 4 meters of the mill are not sufficient to give reasonable size reduction ratios for the production of fines. Application of only damming rings without classifying liners resulted in inverse ball size classification which lead to reduction in size reduction performance thus specific breakage rates.

Jan 1, 2014

By J. J. Cai

The status of fossil fuel and secondary resource in metallurgy industry in China were reviewed, and conversion efficiency of fossil fuel, utilization technologies of secondary energy were studied. Fossil fuel, accounting for over 90% of energy structure in metallurgy industry, took in the highest flight in China, and a great deal of which was converted to secondary energy through the equipment of blast furnace and coke oven. These secondary energy which were mostly made of blast furnace gas(BFG), coke oven gas(COG) and Lindz Donawitz gas(LDG) occupied about 30% of total secondary energy. The way enhancing fossil fuel conversion efficiency, secondary resource recovery and the secondary energy such as BFG, COG, LDG utilization promoted to save fossil fuel was discussed in this paper. And efficient use of lower caloric value fuel was studied, such as preheating combustion air and fuel, generating electricity power etc. and regeneration purposes of high-caloric fuel was also researched, for producing hydrogen, methanol or direct reduction iron etc. The using model of secondary energy at iron and steel works was presented as fuel and chemical materials. The results suggest that utilization of these energy efficiently and reasonably could help to energy saving and environment protecting.

Jan 1, 2014

The objective of the paper is to develop a material balance calculation procedure for a production unit involving two plants separated by a pipeline. The case study is taken from the oil sands industry. The raw sands are first mixed with water in a conditioning plant, then transported through a pipeline to an oil extraction plant. The combination of pipeline dimensions and nominal throughput creates a significant variable time lag between the two plants. As usual, mass balance calculations required for the evaluation of plant performance indicators, such as bitumen recovery, are inaccurate due to measurement errors. In addition, in the present case study, the time lag of the pipe creates an additional source of uncertainty, which may lead to misinterpretations and wrong decisions. Raw data are usually reconciled through steady-state mass balancing, to correct for measurement errors. However, because of the significant pipeline dynamic lag, standard steady-state daily mass balance may fail at giving an appropriate picture of the operations. The proposed solution to the data reconciliation problem includes the use of a pipeline plug-flow model in the mass balance calculation. To fulfil the industrial constraint that current data reconciliation must not modify past reconciled values, while still satisfying dynamic constraints, a daily one-step method, i.e. a unitary filter-ing horizon, is recommended. The method is illustrated with simulation data, and the results com-pared to those of standard data reconciliation methods.

Jan 1, 2014

By Pat Turner, Abrie Schutte, Tim Olson, Roman van Ommen

The key to good cyclone circuit design and operation in primary grinding circuits will be discussed. Cyclone circuit design issues include individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration. Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. The new gMAXTM. cyclones will be introduced and evaluated using operating circuit data in closed circuit grinding applications

Jan 1, 2003

By Ralph J. Holmes, Victor Sharp, Steven J. Spencer, Kevin J. Davey, Jonathan J. Campbell, Peter L. Phillips, David G. Barker

"Improved measurement tools for monitoring and control of AG/SAG mill performance have a high level of interest in industry. Historically, acoustic emission monitoring has been widely used on SAG/AG/ball mills and hydrocyclones to provide new information on the conditions inside these devices affecting their performance. The current work was focused on a new technique using surface vibration monitoring of a number of pilot-scale and production-scale AG/SAG mills to yield insights into the events occurring in the mills. The development of relationships between signal analysis outputs and mill operating conditions can be used for soft-sensor measurement of mill process variables. The technique used an array of accelerometers mounted on the mill lifter bolts linked to a fast data acquisition system which monitored the surface waves generated during operation. Details of the system are presented. Mill operating variables were adjusted systematically to provide a wide range of operating conditions for surface vibration signal collection. The experimental approach is discussed.The signals acquired during the experiments were analysed using a range of techniques. The results show that strong relationships exist between measured vibration power (both total power and within certain frequency bands) and mill load level/power and mill speed. A new method for extraction of power spectral density and band power information on features of interest in a mill rotation cycle is also presented.These results show that single sensor analysis information from the surface vibration system can be used as soft sensor inputs for monitoring process variables such as mill load that until now, have not been reliably measured. System outputs also show considerable promise in the area of condition monitoring. An example of the signal analysis output is presented showing elevated vibration levels in an area with higher resultant wear. Eventually, it is considered that outputs from this system for process variable and wear condition monitoring will be key new inputs to an online AG/SAG mill monitoring and control system."

Jan 1, 2003

By U. Ulusoy

Surface roughness and acuteness are known as the two of the main properties of the particle morphology affecting the behavior of the powders in the process. Since the techniques used for the morphological characterization of powders by 2-dimensional microscopic measurement from the polished sections that have some disadvantages, the 3-dimensional analysis has often relied on measurements of particle morphology. A review of literature data was presented for high-grade barite and pyrite particles ground by ball and autogenous mills to determine the morphological properties using a new 3-D approach based on BET nitrogen gas adsorption and Permaran methods. Micromeritics Flowsorb II 2300 instrument which employs BET nitrogen adsorption technique was used for the specific surface area measurements and the roughness of the particles. Permaran (manufactured by Outokumpu Oy) was used for the measurements of airflow resistance of powder samples for the acuteness. Spherical glass beads were used as reference sample for the acuteness measurements. The obtained parameters, which are surface roughness and acuteness, were corre-lated with the floatability performance of those mineral particles. The flotation performances of those particles ground in different mills (ball and autogenous) were also evaluated by a Hallimond tube. The results showed that lower roughness and acuteness values caused higher flotation recoveries for both barite and pyrite particles that were tested independently in different type of the mills. In other words; particles with smooth surfaces resulted in better floatability for barite and pyrite minerals studied.

Jan 1, 2014

By P. M. Solozhenkin

On the territory Sakha (Yakutia) are located largest in Russian Federation reserves of antimony ores, Sarylakhsk and Sentochansk deposits, amaunt 10% of world stocks of antimony. A processing gold antimony ores Sarylakhsk deposit is carried out on gravitation-flotation circuit to receive gold gravitation concentrate and gold-antimony flotation concentrate with the contents of antimony over 60%. The gold-bearing concentrate is treated on place hydrometallurgicaly to a high-standard product, accepted by gold bank cash department. At the ore dressing plant reached the highest recovery in world in a concentrate of antimony 90%~91.6%, and gold 85.7%~86.0% as a result of scientific research works. Studied the mechanism of interaction cations of metals Pb2+, Cu2+, Cd2+, Hg2+, Ag+ with a surface antimonite presented on the basis of modern physical-chemical methods: nuclear quadrupol resonance, x-ray electron spectroscopy, electron spin resonance. The industrial tests of sodium dimethyldithiocarbate were carried out which confirmed high recovery of Sb and As. The leaching Sb2S3 by bacteria Desulfovibro desulfuricans and transformation antimonite in antimony trioxide by Tiobacillus Ferrooxidans improved following cyanidation . The extraction of antimony in a solution 96.0%~98.0% under optimal conditions. The common total extraction in the appropriate commodity products for gold reached 98%, for Sb 96.5%. At a combination of bioprocessing and cyanidation 85.5% of extraction Au was achieved. The new solvents for antimonite were found. Now by the Close Joint-Stock Co ?Sarylach-Antimony? industrial plant is constructed for processing Au-Sb concentrates to receive antimony trioxide and gold from various antimony deposits of Sakha (Yakutia).

Jan 1, 2014

By D. DePaoli, P. Zhang

"Phosphate ore is one of the most significant secondary resources for rare earth elements (REEs), and Florida phosphate is of particular interest due to its much higher ratio of heavy REEs, especially yttrium. Analyses of numerous samples from different phosphate processing streams in Florida showed that heavy REEs account for about 50% of the total REEs in Florida phosphate with yttrium accounting for approximately 30%. It was estimated that the amount of yttrium from US phosphate processing could meet the world demand for this critical element. This research aimed at recovering both REEs and phosphorus from a phosphate flotation tails. This tails is composed of mainly silica and phosphate with a small fraction of heavy minerals including monazite and xenotime. Since the specific gravity of silica is 2.6 versus 3.2 for phosphate and 4.5-5 for rare earth minerals, pre-concentration of the minerals of interest by gravity separation was investigated first. A pilot scale shaking table was used in this study. One pass gravity concentration achieved a shaking table concentrate analyzing over 600 ppm REEs at about 40% recovery. Flotation of the shaking table concentrate resulted in a product containing 1809 ppm REEs and 26.37% P2O5 with corresponding recoveries of 73% and 82%. Sulfuric acid leaching at 75oC could recover over 60% REE and nearly all the P2O5. Higher REEs (>90%) recovery was achieved by conducting leaching at higher temperature with concentrated sulfuric acid. The phosphoric acid from leaching of the flotation concentrate is of superior quality compared with that generated from regular phosphate rock.INTRODUCTION Rare earths are a group of 17 elements including those of the lanthanum series, as well as the non-lanthanides, yttrium and scandium. These elements have very specific critical uses in a multitude of markets. For example, lanthanum is used as a catalyst in breaking down crude oil to produce gasoline, diesel and jet fuel and neodymium is the core magnetic component in high-strength magnets for electric car batteries, wind turbines and hard disk drives. Rare earths are also essential for many military applications. Many of these applications have no substitute materials and the move to green technologies has dramatically increased their demand."

Jan 1, 2018

By Jie-Liang Wang, Yongdan Cao, Zhao Cao

"The effect of ethylenediamine tetraacetic acid (EDTA) on flotation separation of fluorite from bastnaesite and its selectively depression mechanism on fluorite were studied by single mineral flotation, artificial mixed minerals flotation, solution chemistry analyses, Zeta potential and XPS measurements.The results show that fluorite can be deeply depressed by EDTA while the flotation of bastnaesite is almost unaffected when octanohydroxamic acid (OHA) is used as a collector. The separation index (SI) between bastnaesite and fluorite increases with the dosage of EDTA, SI can be raised from 1.18 to 12.66 when EDTA dosage increases from 0 to 2×10-3mol/L.Solution chemistry analyses show that EDTA is able to convert the Ca(OHA)2 hydrophobic precipitation on fluorite surface to a soluble Ca-EDTA complex but cannot complexly dissolve the Ce(OHA)3 precipitation on bastnaesite surface. Therefore, the Zeta potential of OHA conditioned fluorite can be reduced significantly by EDTA while the reduction degree to Zeta potential of bastnaesite is relatively low. XPS measurement shows that EDTA removes the chemically adsorbed OHA from fluorite surface but has little effect on the adsorbed OHA on bastnaesite surface. As a result, fluorite can be selectively depressed by EDTA in bastnaesite flotation, which behaves an important industrial application prospect in rare earth ore flotation.INTRODUCTIONNowadays, Rare earth elements (shortened as RE) and compounds are of significant importance for a range of rapidly expanding industrial applications including catalysis, metallurgy, renewable energy, and special materials due to their unique electrical, magnetic, optical and chemical properties [1]. The seventeen RE elements, including the lanthanide-group fifteen elements, yttrium and scandium, could be divided into three groups, i.e., light, medium and heavy RE elements based on the different solubility of RE sulfates [2]. Bastnaesite ((Ce,La)CO3), containing approximately 75% REO, is one of the most important light RE minerals [3]. Flotation is the common method to recover basetnaesite [4-6]. Nonetheless, basetnaesite is often associated with calcium-bearing gangue minerals such as fluorite, and the separation of basetnaesite and fluorite by flotation is usually difficult due to their similar surface properties and therefore floatability [7-9]. Therefore, research on high selective flotation reagents of bastnaesite over gangue minerals has attracted a lot of attention [10]."

Jan 1, 2018

Hydrofluoric acid (HF) is traditionally used in plant operation to separate feldspars from quartz. It acts during the conditioning step as a pH regulator and an activating agent providing an excellent selectivity. However, a corrosive chemical environment and the ecological impacts from the potential fluoride ion contamination are limiting factors to use this chemical agent at an industrial scale. Investigations of the amine-feldspar interactions in the absence and presence of non-linear long-chain alcohols were carried out on two ore samples. The presence of alcohol molecules led to form a closed packed layer only on the surface of feldspars. The highest order and packing at the feldspar surface were observed with a particular alkyl chain structure as Guerbert alcohols. A new flotation process was developed and tested at both lab and pilot scales on different feldspar ores. The Guerbert alcohols allow to perform a feldspar concentrate with very low content in quartz (2.3-3.5 %) and feldspars recovery from 78 to 81 % while the aliphatic isoalcohols show a more higher recovery level (88-89 %). New HF-free process is strongly dependent on the pH range (1.7-2.5) and sulphuric acid consumption during conditioning steps. Optimal amine/alcohol weight ratio is ranged between 0.8 and 1.0. The values below 0.8 decrease strongly the flotation selectivity and the quartz recovery within the feldspar concentrates is higher than that occurs with HF.

Sep 1, 2012

By P. Altinkaya, O. Celep, H. Deveci, E. Y. Yazici

"Copper-bearing gold ores have proved difficult to treat in conventional cyanide leaching process owing to prohibitively high consumption of cyanide by readily soluble copper minerals interfering with gold extraction. Cyanide leaching of gold from copper-rich ores can be improved by intensive cyanidation or application of physical and chemical pre-treatment methods (e.g., ultra-fine grinding, roasting and leaching). In this study, nitric acid leaching of a copper-bearing pyritic concentrate (0.3% Cu, 62 g/t Au and 110 g/t Ag) as pre-treatment prior to cyanidation was investigated. The mineralogical analysis of the concentrate has revealed that it is composed of mainly quartz (25%), pyrite (32.7%), sphalerite (5.37 %), galena (2.12 wt %) and anglesite (1.13 %). Arsenopyrite, chalcopyrite, covellite and bournonite were also detected as minor phases present. Previous studies carried out by the authors showed that direct cyanidation (1.5 g/L NaCN) of the as-received concentrate (d80: 80 µm) produced low gold (45% Au) and silver (46% Ag) extractions. Nitric acid pretreatment of the as-received concentrate was performed for 5 hours at 1-5 M HNO3 and 80oC. In these tests, 65% Cu/Pb and 94% Zn were leached. The nitric acid pre-treatment improved the extraction of gold and silver in subsequent cyanide leaching (1.5 g/L NaCN) to 82% Au and 87.5% Ag with a concomitant decrease (up to 54%) in cyanide consumption. It can be inferred from these findings that the removal of copper from the concentrate and the liberation of the occluded gold by nitric acid leaching as pretreatments can be appropriately employed for the treatment of the copper-bearing pyritic concentrate with high gold/silver content. INTRODUCTION Refractory ores are often characterized by their low amenability to cyanide leaching resulting low (often <80%) Au/Ag extractions (Bhappu, 1990; Celep et al., 2009; Marsden and House, 2006). One of the most common causes of refractoriness is the physical or chemical encapsulation of submicroscopic or fine-grained gold in sulphide minerals such as arsenopyrite and pyrite (La Brooy et al., 1994; Vaughan, 2004). To render refractory gold ores/concentrates amenable to cyanide leaching, the decomposition of sulphide minerals within a pre-treatment process to expose the encapsulated gold grains to the action of cyanide is required. In this regard, roasting, pressure oxidation and biooxidation are commercially used processes for pretreatment of arsenopyrite/pyrite gold ores/concentrates ahead of cyanide leaching (La Brooy et al., 1994). Presence of cyanide-soluble copper minerals in the ore leads to low gold recoveries and high cyanide consumptions under conventional cyanide leaching conditions. High cyanide concentrations (CN:Cu>4) should be employed to achieve high gold recoveries from copper-rich gold ores/concentrates. This may require recovery of cyanide from effluents. In this regard, SART Process (sulphidisation-acidification-recycling-thickening) employed industrially for recovery of cyanide and copper as a by-product. This process simply relies on the addition of sulphide (as Na2S, NaSH or H2S) to the leach solution prior to the acidification to pH 4-5. This results in the precipitation of copper as Cu2S and occurrence of free cyanide which is recycled to the leaching circuit after S/L separation (Dai et al., 2012)."

Jan 1, 2018

By N. I. Tyushkova

This is a brief survey of the technological solutions for deep cleaning of baddeleyite?s concen-trate. Baddeleyite is part of kamaphorite of composite apatite-magnetite ore in alkaline-ultrabasic mountain range of Kola Peninsula. Baddeleyite?s concentrate, which is being produced by Kovdorsky GOK (ore mining and processing enterprise) contains 97.5%~98.5% (Zr?2 + ?f?2) and also scandium oxide (0.05%). It is usually used without any chemical processing. World demand for zirconium oxide is constantly on the rise. Its consumption grows in ceramic industry and in high-tech spheres. That?s why the demand for its purity is very important nowadays (additional cleaning from phosphorus, silicon, iron, aluminium). The mechanism and kinetics of interaction of activated bad-deleyite with sulphuric acid has been studied as well. While applying method of mathematical mod-eling it was confirmed that the mechanical activation is effective for the intensification of sulphation process of baddeleyite?s concentrate with the aim of purifying it from dirt. The use of the calculated optimal regimes allows to reduce such technological operation factors as: temperature, the du-ration of process, the sulphuric acid consumption. It also allows to determine the conditions of anticipatory abstraction of scandium and main dirt in solution in comparison with zirconium oxide.

Jan 1, 2014

By Xiaoxu Sun, Jianchao Yao, Jiancheng He, Shijie Lu, Hongxi Zhou

"With the trend of increasingly more mineral resources turning low-grade and refractory, more and more new ore bodies being developed worldwide are more finely grained, which drives the rapidly development and application of techniques related to tower mills (vertical spiral stirred mills). However, the lacking in fundamentals of fine grinding, as well as standard procedures for equipment selection and scale up, seriously restraint high efficient application of tower mills. Taking grinding media motion characteristic and grinding intensity as a breakthrough point, this paper studies mechanisms behind how critical parameters affect grinding efficiency of tower mill, including ratio of screw pitch and diameter, agitator rotation speed, grinding media size. Several sets of orthogonal test are conducted on the quartz ore using the grinding system of KLM-3 tower mill. All the tests are under the same character of feeding mineral and undergo the consistent sampling for at least 60min grinding time. The input power is measured by a torque measurement system and the grinding products are analyzed by the laser particle size analyzer. The test results show the influence of parameters on grinding efficiency. Among the three important parameters, the effect of grinding media diameter is the biggest, followed by the agitator tip speed, and finally the ratio of screw pitch and diameter. For the different particle size of grinding products, the best combination of grinding parameters is different, with the mineral size becoming finer, the ratio of screw pitch and diameter become smaller, the diameter of grinding media become smaller, while the agitator tip speed does not change too much. The conclusions of the study help us to improve the grinding efficiency of the tower mill, to assist in the selection and optimization of working parameters, establish new scale up method on the basis of grinding model and eventually provide theoretical basis of rational selections of structural and media physical parameters within tower mill."

Jan 1, 2018

By Y. F. Li

Fengning ilmenite ore is a magnetic deposit in gabbro containing high phosphorus and low titanium, the main minerals in which are ilmenite, magnetite and apatite. The dissemination size of magnetite is so fine that even the percentage of -0.010mm level is up to 36.50%. The fine and vein magnetite are distributed in gangue and ilmenite, so the majority of the magnetite is difficult to be separated from the gangue. Ilmenite is difficult to be recovered by low-intensity magnetic separation even through fine grinding. In high-intensity magnetic separation of ilmenite, the gangue inter-growth with the magnetite and the Fe-containing silicates may be enriched in the concentrate, and the ilmenite of the concentrate will be reduced. Based on the processing mineralogy research, combined gravity-flotation process is suggested to recover the ilmenite. The method is also good to reduce phosphorus in the ilmenite concentrate.

Jan 1, 2014

By D. R. Nagaraj

The traditional (popular) approach to reagent development and optimization, which has become entrenched in both research and practice for many decades, is highly reductionistic, incremental and costly, does not produce robust chemical solutions, and is not sustainable. There are also several other key drivers and changes in the mineral industry that clearly warrant a new approach. In response to these, an intense effort was made at Cytec over the past fifteen years to develop a meaningful, efficient, and sustainable approach to develop new reagents and robust chemical solutions in mineral separations. This effort culminated in three important outcomes: a) development of the holistic approach, called FLOTATION MATRIX 100? process, b) novel reagents, and c) enhanced application knowledge for reagents. In this paper, the efficiency, utility and power of the holistic approach will be demonstrated with examples using both existing and new reagents in the processing of Cu-Au, Au and Cu-Mo ores.

Jan 1, 2014

By Qiuyang Hong, Bo Li, Dongyun Liang

"A weathering-crust niobium-rare earth-bearing deposit is formed by the weathering alterationof alkaline granite, which is refractory due to its low grade and complex properties. The mineralogicalcomposition of ore, the grain size of majorminerals as well as the occurrence of Nb and REE are studied in this paper using MLA combined with traditional methods. According to the results, a wide range of Nb-Ti-REE compound minerals including titanoniobite, uranpyrochlore, chlopinite, samarskite and ilmenorutile areformed for the extensive isomorphous substitution among the elements of Nb, Ta, REE, Fe, Ti, U and Th. The occurrence of REE is extremely complex. First, the REEexistingas rare earth minerals including monazite, xenotime, bastnaesite,etcaccount for 21%. Second, the REEexist in the lattice of Nb and Zr minerals as isomorphous additions, which account for 18%. Third, the REE exist as colloidal rare earthdeposit,which account for 35%. Last, the REEexistingas ion-adsorption-type rare earth,which are adsorbedon the kaolinite in the form of hydrated hydroxyl ions, account for 26%.Based on the results of mineralogy, the combined technology process "mineral processing- hydrometallurgical separation" is needed to deal with the ore. The mineral processing tests show that, for the feed ore containing Nb2O5 0.065%, REO 0.13%, an Nb-REE concentrate containing Nb2O5 1.38%, REO 1.98% can be gained by "high intensity magnetic separation-regrinding-gravity separation by shaking tables". The recovery of Nb2O5 and REO is 62.42% and 44.78% respectively. The Nb-REE concentrate is dealt by the metallurgy process "direct reduction- acid leaching & acidulating- neutralization & precipitation- chlorination & distillation" and the rare earth oxide of 92.34% REO as well as the Nb-Zr oxide of 24.62% Nb2O5 can be obtained with the recovery of REO and Nb2O5 being 76.83% and 59.37% respectively."

Jan 1, 2014

By M. Unesi, S. Haj Mohammadi, M. R. Abdoli, M. R. Garmsiri

"Hydrocyclone-thickener circuit is a promising solution to enhance the dewatering efficiency in mineral industries. The challenges in the circuit is reducing particle size in the thickener feed and the good feature is a rise in the retention time of sediments in the thickener. In this work, the effect of particle size, bed depth and residence time on the thickener performance were investigated. In this order, pilot scale columns were employed at Sarcheshmeh and Shahrebabak copper complexes. Furthermore, the influence of residence time was differentiated due to the variations in the bed depth and settling flux. Moreover, a new approach was introduced to estimate solids residence time in the thickener. results indicated that with smaller particles that are introduced to the column, the bed density as well as thickener discharge solids concentration dropped significantly. It was found that thickener discharge solids concentration fell from 59.6 to 33.8 % with reducing particle size from 130 to 22 µm in the settling flux of 20 t/m2/day. Additionally, it was found that longer residence time and deeper bed resulted in an increase in the thickener performance while the bed depth has a stronger effect. It was proved that employing a hydrocyclone prior to the thickener resuted in an increase in the dewatering efficiency.INTRODUCTION Thickeners are widely employed in mineral industries to recycle tailings and concentrate water content. A limited fraction of suspension water content is recycled using a thickener. For instance, about 50 percent of tailings water content could be recycled using a shallow bed thickener during copper processing. Since the scarcity of global water resources became more serious, the demand for improving dewatering efficiency in mineral industries became more significant [1]. A number of solutions were recommended to enhance dewatering efficiency of thickeners including optimization of current thickeners, employing deep bed thickeners and utilizing thickener-filter or hydrocyclone-thickener circuits. Optimization of existing thickeners is essential, however, it does not meet the significant demand for recycled water. The application of deep bed thickeners (known as paste thickeners) has been rising in the mineral industries [2] due to a higher dewatering efficiency while its costs is remarkable."

Jan 1, 2018

By F. Y. Kang

Graphite with layers structure is easily to form graphite intercalation compounds (GICs) by means of intercalation reactions due to the weak cohesion force among carbon layers, van der Waal?s interactions. By controlling the oxidation-intercalation, high quality exfoliated graphite with low residual sulfur content and MClx-GICs (M=Fe, Co, Ni, Cu, Zn) powder for electromagnetic wave absorbing and shielding materials have been invented. The expansion volume of expandable graphite can be larger than 160 mL/g while the residual sulfur content is less than 800 ppm. The MClx-GICs powder can shield infrared ray and laser completely up to 15 min. We have also in-vented exfoliated graphite for heavy oil adsorption and mild-expansion exfoliated graphite for anode materials in lithium ion battery by controlling the intercalation/de-intercalation. The exfoliated graphite can adsorb heavy oil up to 80 g/g, it also exhibits better performance than commercial active carbon in sewage treatment. The mild-expansion exfoliated graphite as anode material shows high capacity of 370 mAh/g and good cycle performance.

Jan 1, 2014

By Yessengaziyev Azamat, Almagul Ultarakova, Onayev Murat, Barkytova Botakoz

"The research is aimed at solving the processing of waste products of titanium-magnesium production. The aim of the research is to extract synthetic carnallite and industrial products enriched with niobium from waste products of titanium-magnesium production. Analysis of the current state of the titanium and magnesium production in the Republic of Kazakhstan shows the availability of significant amounts of chloride wastes containing valuable components. Magnesium and potassium with an average content of 50-60 % potassium chlorides, 25-30 % magnesium chlorides are lost in the wastes of the titanium and magnesium production. Ust-Kamenogorsk Titanium Magnesium Plant JSC (UKTMP) currently imports carnallite that is a KCl-MgCl2X6H2O binary salt at quite high prices. Chloride wastes of titanium production, sublimates of dust chambers of a titanium chlorinator, sludge of a magnesium electrolytic unit and sludge of a carnallite chlorinator has been chosen as the targets of our research. The analysis of niobium distribution within any solid waste of a titanium slag chlorination process in UKTMP JSC showed that the highest content of niobium is in the sublimates of dust chambers of a titanium chlorinator in the ranges from 0.26 to 1.0 %. Among the niobium extraction technologies considered, the known method of its extraction from the chloride waste is leaching with weak solutions of mineral acids or alkalis in order to convert the chloride salts into the solution to be used for synthetic carnallite extraction. Besides niobium, other impurity components are transferred to the cake and shall be separated from the base metals. The effective method for this is the chlorination process enabling niobium transfer into the sublimates in the form of chlorides and thus separating it from the majority of the impurities. The condensed niobium chlorides are hydrolyzed transferring it into sediments in the form of oxide. New ways of processing waste products of titanium-magnesium production with the receipt of marketable products are relevant in the development of processing of mineral raw materials."

Jan 1, 2018