Search Documents

By Jyotirmoy Sarma

The surface-active agent, like sodium humate, in the present systems produces a very stable suspension. Saline water up to 15% is used as a flocculating agent for recovery of water from the dispersed phase containing 1% solid. The recovered water in the presence of humate at different concentrations (0.05-0.2%) and at pH 8 also produces a stable dispersed phase of iron ore fines and tailings. The beneficiation techniques adopted in the present systems can increase ~ 2-3% iron value in the concentrate of iron ore fine, however, for tailings the increase in iron value is not observed. Keywords: beneficiation, flocculation, iron ore fines, tailings, saline water, surface-active agent

Sep 1, 2012

By Stoyan Gaydardzhiev, Michel Shengo, Pierre Kalenga

Lab-scale flotation of copper and cobalt oxidized ore from the Luiswishi deposit in the Katanga province (DRC) has been done focusing on the influence of the degree of process water recycling on metals recovery. Results have shown that at 20 % recycling rate, the recovery of copper and cobalt in the cleaner stage have been respectively reduced to 23 % and 45 % in comparison to 53 % Cu and 63 % Co if process water has not been recycled. At 10 % recycling rate however, the system could still tolerate the effect from recycling, since Cu and Co recovery has remained respectively at acceptable levels of 52 % and 60 %. In order to explain the reasons for the observed worsening of flotation results if process water was recycled at rate higher than 20 %, electrochemical investigation of the pulp has been performed. It has been established that the chemical compounds formed in the pulp when process water was recycled, do influence the sulphidization of malachite and heterogenite and impact further collector adsorption. To confirm these assumptions, the effect from thiosulphate ions presence during the sulphidization of high purity malachite has been studied. It has been found, that thiosulphate ions depending on their concentration in water induce variations in pulp properties such as DO content, pH, Es and contribute to formation of undesirable chemical compounds on mineral surface as identified by DRIFT spectroscopy.

Jan 1, 2014

By David Morrow

Fly ash is a by-product from coal-fired power stations that is captured from the exhaust gas stream by electrostatic precipitators (ESPs) or bag houses. It is mainly derived from the inorganic components in coal but also contains residual carbon from unburnt fuel (measured as LOI). In the past, nearly all fly ash was sent to landfills or tailings ponds by power generators but this trend is quickly changing due to landfill costs, sustainability requirements and the inherent value in correctly processed fly ash. The main property that makes fly ash suitable for recycling is its use as a pozzolan. Pozzolans exhibit cementitious properties that make them suitable for partial cement replacement, and that can have beneficial properties for concrete mix designs. Fly ash can be used to replace up to a third of the of the Ordinary Portland Cement (OPC) requirement. Suitable fly ash nearly always requires the removal of the less reactive coarser fraction from the finer fraction. Due to the pozzolanic nature of fly ash, it must be processed dry and separation is normally required at 45 micron. In response to the increasing demand from a range of dry classification applications, Metso purchased an established air classification technology suitable for both mining and construction applications. The classifiers intelligent design efficiently utilizes the air flow which keeps power requirements low whilst including a scrubbing/recirculating function within the classifier that allows extremely efficient separations even at very fine sizes. This technology is of global interest to Fly Ash processors, but should be of particular interest in India which is both the second largest cement producer in the world as well as producing 80% of its power from thermal sources. This paper is intended to give a brief overview of fly ash and requirements for use as a pozzolan, air classification of fly ash and a case study from an established and experienced fly ash producer. Keywords: air classifier, fly ash, pozzolan, fineness, cement, cholla, salt river materials group

Sep 1, 2012

By Herman D. Mendoza

A rapid recovery/recycling process was introduced utilizing the surface-chemical properties of finely dispersed mercury and alumina (Al2O3) fibers in aqueous environment. The conventional method of amalgamation or .ball milling. involves the mixing of a substantial amount of mercury to collect free gold during the grinding stage. In effect, a portion of the mercury is transformed into minute droplets that readily float and disperse in the amalgamation effluent. The fine droplets of mercury in the dispersion readily attached onto the positively charged macroscopic alumina fibers (i.e. = pH 9.8) at conditions pH 3 to 10. When an effluent from settling procedure after an amalgamation-grinding stage is passed through a column-bed packed with alumina fibers, maximum collection of negatively charged finely dispersed mercury occurred at pH 3 to 6. The collection/attachment efficiency was 99.5%. The collected droplets of mercury, which are left in the column-bed of alumina fibers, were subsequently rinsed with alkaline solution at pH 10 to 11.5. At these conditions, both mercury and alumina fibers carry negative surface potentials and resulted in the partial detachment of mercury from the alumina fibers. The detachment efficiency was only 30-35%. The attachment/detachment mechanisms in this study were analyzed using the DLVO theory.

Jan 1, 2003

By Felipe Sepulveda, Edelmira Gálvez, Luis Cisternas

"In mineral processing, the recovery and/or concentration of the value components cannot occur in one operational stage, therefore requiring the use of separation circuits based on several flotation stages. The components to be separated are typically distributed at different concentrations and different particle sizes, resulting in different levels of recovery. Typically, more than one value component must be selectively removed by exploiting the differences in the components’ floatability at different pH values, pulp potential and particle size. Several methods for the design of these circuits are available in the literature, but comparatively few studies present circuit analysis tools or address the design of a multiple-product flotation circuit. In this study, global sensitivity analysis was used to analyze a flotation circuit with several products, such as copper, lead and zinc. This analysis was based on the Eureka mine concentrator plant. The analysis was performed for each of the sections of the circuit as an overall evaluation of the circuit. The Sobol’ method and the correlation method were used to evaluate the Eureka mine concentrator plant using the SimLab 2.2 software."

Jan 1, 2014

The characteristics of mineral resources and tailings resources in China are analyzed. Those tailings, which have double characteristics, can occupy land, pollute environment and even influence human habitat if they are not disposed in time. So pay attention to the comprehensive utilization of the tailing more and more both at home and abroad. The present situation and problems in comprehensive utilization of iron tailings in China are introduced by combine some practice experience, and have looked forward to the comprehensive utilization of iron tailing situation.

Jan 1, 2014

By L. Z. Li

The application of some environment-friendly mineral processing technology was introduced in Xitieshan lead?zinc mine and Hugary copper mine of China Western Mining Co., Ltd, located in western plateau area where the ecological environment is extremely fragile. The results of the significant economic efficiency were obtained by applying these new techniques while the protection of peripheral environment and the improvement of ecology were made.

Jan 1, 2014

By B. Das

Waste water produced from coal preparation plants posses several problems during dewatering and solid/liquid separation. The natural sedimentation rate of the particles present in colloidal and finely divided suspended form is very slow. Flocculation technology is being applied in most of the coal washeries to recover water which is being accomplished through the use of inorganic salts, polymeric flocculants or both depending on the chemical and physical characteristics of the pollutants present in the waste water. The waste tailing water from Piperware coal preparation plant, Central Coalfield Limited (CCL), India, is highly turbid containing ~ 16000 NTU with negative surface charge in the pH range of 2 to 10. Polymeric flocculants in conjunction with fine magnetite is investigated to achieve faster settling rate with lowest level of water turbidity. The conditions affecting the interaction between the reagents and the turbid particles present in the tailings water are investigated. It is possible to bring down the turbidity of the water to < 90 NTU from very high turbid tailing water by using 2 mg/L of the polymeric flocculent in combination with 0.1 g/L of magnetite at natural pH of the tailing slurry. It has been found that finely divided positively charged magnetite particles in combination with the flocculent selectively coat the negatively charged impurities present in water and thereby increase the settling rate under the influence of a magnetic field.

Jan 1, 2014

By Venugopal Tammishetti

One of the important technological challenges facing the iron ore industry in India is to find commercially viable technologies to process alumina rich iron ore fines and slimes. The key to solving this problem lies in developing selective reagents for the separation of iron oxide minerals from associated gangue minerals like quartz, gibbsite, kaolinite and montmorillonite. We present in this paper our successful results on the dispersion-flocculation of three different natural iron ore slime samples from mines in India using the reagent combination of PVP dispersant and corn starch flocculent. All the three samples contained hematite, goethite, kaolinite and gibbsite minerals as confirmed by X-Ray Diffraction (XRD) analysis. The effect of various process parameters such as pH, dosage of reagents, settling time and pulp density was studied. We were able to produce a concentrate assaying 66.2% Fe and <2% Al with a yield of 67.4% by weight (with a recovery of 77% of iron values) using PVP (1 ppm dosage) and corn starch (20 ppm) for one of the slime sample (Sample I) assaying 58.2% iron (Fe) and 3.8% aluminium (Al). The XRD analysis of settled and dispersed fractions revealed that alumina-containing minerals like clay and gibbsite mostly remain in the dispersed phase while iron-bearing minerals tend to concentrate in the flocculated fraction. Keywords: iron ore, slime, flocculation, dispersion, beneficiation, starch, polyvinylpyrrolidone

Sep 1, 2012

By H. C. E. Regidor, M. G. Mena, H. D. Mendoza

Cyanidation leaching has always been the most widely used method of extraction of gold in the world. Its low cost and high selectivity has made it the prevalent choice for mining companies, and even for the small scale miners. The use of cyanidation in small scale mining has been an issue for the longest time, mainly due to the operation’s lack of safety measures, health care or environmental protection regulations. In pursuit of more environmentally friendly methods of extraction of gold, several alternative extraction processes have been explored, one of which is chlorination. The chlorination process is advantageous when recovering refractory gold locked in sulfides, as it simultaneously oxidizes the surrounding sulfides as well as dissolve any gold exposed to the lixiviant. This research was conducted to study and develop a safer alternative way of extraction of gold from small scale mining operations, without compromising the recovery of gold. In this study, a variation of the chlorination process has been employed for a refractory flotation concentrate wherein the majority of the gold is locked in sulfides. Hypochlorite-bearing reagents were used as the leaching reagents, and the method developed was a 2-stage leaching process in differing pH conditions. The solution pH and Eh was monitored all throughout the runs, and aliquot samples were taken at time intervals for analysis. SEM-EDS imaging was used to determine the mode of oxidation of the chlorination process, and the image obtained showed that the oxidized layer followed the shape of the particle, suggesting a diffusion controlled process. XRD analysis of the sample before and halfway through leaching further confirmed the oxidation of the sulfides. The amount of gold dissolved in the aqueous solution and in the solid residue were used as the basis for the determination of the recovery of gold. An average gold recovery of up to 84.38% was obtained using the developed method in just 7 hours of leaching. This method was then employed for a pilot-plant scale test and a gold recovery of 79.2% was obtained.

Jan 1, 2018

By T. Wallmach, S. B. Blancher, A. Delaporte, P. Goncalves

"Fe-Ti oxides concentrates produced from heavy mineral sand deposits are widely used for the production of titanium dioxide pigments that are critical components of white paint, plastics and paper. According to mining industry, the Fe-Ti concentrates mostly consists of three phases: ilmenite, leucoxene and rutile. However, a few mineralogical studies have shown that the variety of Fe-Ti oxides found in sand deposits is far more complex, mostly due to alteration processes. The aim of this contribution is to characterize in detail by means of Qemscan analyses the mineralogy of the three main concentrates (ilmenite, leucoxene and rutile) produced by the Grande Côte Operation (GCO) mineralurgical plant in Senegal. The ultimate goal is to characterize the different products and textures formed during the natural ilmenite alteration processes, to localize the phases carrying the main impurities (Cr and P), and finally to determine the physical properties of each mineral component to improve metal recoveries. Along alteration processes, Ti content increase. Ilmenite (FeTiO3) is progressively transformed into pseudorutile (Fe2Ti3O9) particles which could also be altered and transformed into hydroxylian pseudorutile [FeTi6O12(OH)3.3H2O] or complex blends of anatase microcrystals (TiO2). These transformations are accompanied by significant changes in particle textures. Microporosity and fractures appear and the impurity content also increases. Anatase rich microcrystal assemblages, so far described as Leucoxene, could be identified to consist of grains with higher porosities, water contents and higher intrapore impurities. These particles are the main carriers of chromium and phosphorus. The observed mineral transition textures have a significant impact on the ore dressing processes. During these transformations, the physical properties of these phases change, the magnetic susceptibility as well as densities decreases, due to the increase in porosity. The separation of particles, especially those with high porosity will help improving the GCO mineralurgical plant performance and to reduce the impurity contents in finals products."

Jan 1, 2018

By N. Syna

The selection and preparation of activated carbon suitable for specific application can often involve exhaustive adsorbent preparation and testing. This work examined an emerging technique based on modelling the correlation of observed adsorption capacity to the carbon characteristics as a means of decoupling the roles of carbon textural and surface chemical properties. The insights to these specific roles are then used in tailor-making adsorbents and in establishing the optimal carbon properties for specific application. In this study, a series of activated carbons prepared from bagasse by physical and chemical techniques and commercially available carbons were used in developing the models. These carbons were tested for the adsorption of thiourea-gold (I) chloride complexes. Thiourea is an important alternative gold lixiviant with the potential to address current ecological and safety concerns in the extraction of gold. A four-component model, which correlated the adsorption gold capacity to carbon textural and surface chemical properties, was proposed. The model fit was assessed using multi-linear regression and a partial F-test. This was followed by goodness of fit test achieved through r2, adjusted?r2 and mean square error (MSE) values. The results suggest the adsorption of the gold-thiourea complex is strongly influenced by the internal surface area and pH of the carbon. Tailor-made activated carbon from bagasse showed adsorption gold capacities of up to 198 mgAu/g adsorbent, demonstrating the potential of bagasse as a precursor for gold adsorbents and of this empirical modelling approach in developing adsorbents for metal recovery.

Jan 1, 2014

By Diana Drinkwater

As ore grades decline, ore deposits get harder and mineralogical complexity increases, metallurgical skills are more important than ever to ensure that today?s mining operations are operating efficiently and profitably. Yet specialist undergraduate degree programs have all but disappeared and metallurgical skills training for graduate engineers in the workspace if often haphazard. In response to this situation, specialists at the JK Centre in Queensland, Australia, have put together a professional development program designed to fast-track skills development for early career metallurgical professionals. The program, called ?MetSkill ® ?, is offered as a group training package for young metallurgists in the workplace. It is centred on a meaningful technical investigation negotiated between the JK Centre delivery team and the client company. As well as learning about project management and data collection and analysis, the participants study specialist topics such as comminution, flotation and mineralogy under the tutelage of senior research and consulting professionals. The technical investigation provides an opportunity for immediate practice of these new skills and JK Centre specialists are on hand to provide feedback and support throughout the program. The participants are employed across different operations in Australia and the Asia-Pacific, and although they occasionally come together for group training activities they are often separated by considerable distance. Specialist educational professionals from The University of Queensland have provided an innovative web platform to support collaboration and communication between all participants. This paper will describe the MetSkill ® program in detail, as well as providing a report on its initial roll-out to 2 groups of Australian graduate metallurgists in 2012

Sep 1, 2012

In this study, selective flocculating of diaspore using anion macromolecular reagent as flocculant was tested to separate diaspore from alum-silicate minerals. Firstly, the effect of pH on settling behavior of diaspore and kaolinite dispersions has been investigated. The results show that the maximum settling speed of diaspore and kaolinite appeared re-spectively at pH7 and pH3.33 which is close to the point of zero charge (PZC) of diaspore (6.8) and kaolinite(3.5). This result is in well agreement with the double electric layer theory. Secondly, the settling behavior of diaspore and kaolinite particles in different anion flocculant solution have been researched. The results indicate that flocculant solution concentration significantly affect the selectivity and the flocculating performance of anion molecular. In high concentration solution, both diaspore and kaolinite have faster settling rate compared to blank solution. How-ever, in low concentration solution, the anion macromolecular can enhance the settling rate of diaspore remarkably but has no apparent effect on the settling rate of kaolinite. This result suggests that the tested anion flocculant is a promising reagent for de-silica of diasporic bauxite. Lastly, FTIR method was employed to probe the adsorption mechanism of flocculant on diaspore and kaolinite. The results reveal that there are anion flocculant characteristic bands on the spectra of diaspore but no obvious characteristic bands of flocculant on the FTIR spectrum of kaolinite. This result is in good correspondence with settling test.

Jan 1, 2014

By D. Renda

With thise Process of obtaining a solid fuel which is both ecological clean and has a high calorific value by a two-stage method of enriching preferably type lignitic coals to remove a high content of all sulphurs, incuding organic sulphur, which method comprises converting the coal to a semi-coke from followed by magnetic separation. In the Experiments given the best results the washed lignite coal in the West-Turkey, Tavsanli- Region, size -3.35 mm on dry basis. In the microscopic studies of the brigh-thin cross-section taken from the samples of sulfur min-erals pyrite in the dimension of 2~50 micrometers and melnicovite 10 micrometers particles. An thermal treatment an semi-coking themperature between 370°C to 650°C give the best Result of 480 °C. The oxidation and decomposition of sulphur minerals pyrite and melnicovite in lignite coal proceed the iron oxides Fe2O3 and pyrrhotite FeS on the surface layer. The Magnetic Seperator (Rare Earth Magnetic Separator, REMS) is capable this two form of sulphur, including organic and inorganic sulphur, in semi-coke and resulted in the magnetic-fraction in REMS. The non-magnetic-fraction remove total sulphur by 68 %, ash by 44 % and increase the upper calorific value in 15 %. The clean lignitic coal can be utilized in human or energy power stations.

Jan 1, 2014

By Liu Xinghua

Yuanjiacun iron ore located in Shanxi province of China has finely disseminated grain size and contains refractory iron-bearing silicate gangue minerals such as chlorite. Therefore, a large amount of secondary slime (the content of -10µm fraction was up to 32.92%) was produced inevitably in fine grinding process, and chlorite was also enriched in concentrate from the content of 4.3% to 14.8% after high intensity magnetic separation. These two characteristics result in the difficulty to deal with Yuanjiacun iron ore by flotation. In this test work, contrast tests between single reverse flotation and selective flocculation desliming-reverse flotation were conducted on Yuanjiacun iron ore. The test results show that after selective flocculation desliming, the iron grade of cationic reverse flotation concentrate increases by 6.15% and the recovery increases by 7.25%; the iron grade of anionic reverse flotation concentrate also increases by 2.15%. Furthermore, analyses of grain size composition and mineral composition were carried out on separation products, the results indicate that selective flocculation desliming plays a dual role of optimizing grain size composition of flotation feed and removing iron-bearing silicate gangue minerals (chlorite) effectively.

Sep 1, 2012

By N. J. Bolin

The Aitik copper mine is located in the north of Sweden and the concentrator at the mine started its operation in 1968 with a capacity of 2 Mton ore per year. Since then the operation has expanded several times, and today the capacity is 18 Mton ore per year. A new expansion plan was investigated in 2005, however the building of a new concentrator was found to be a better solution, giving a lower cost, a longer lifetime and more concentrates to the smelter at the coast. Several choices have been evaluated regarding the location of the concentrator?s crushing, grinding, dewatering, process control and water systems. The energy cost comparison has been an important factor when evaluating the various choices. The single most important decision has been in choosing the grinding system. Once again the fully autogenous grinding system, favoured by Boliden, has proven to be the best solution. The location of the mill, high and near the tailing pond, gives lower transportation costs for the ore and tailings, compared to other locations. A new water system will lower the pumping cost, give better control of water circulation to the plant and create fewer problems with permafrost in the tailings disposal area. Molybdenum recovery will be installed in the new plant using a separate circuit. A gold leaching plant was also investigated. Gold leaching is planned for the pyrite concentrate from the chalcopyrite/pyrite separation and the concentrate from the desulphurisation circuit that will be installed on the bulk flotation tailings.

Jan 1, 2014

By Shugang Hu

According to XRD, DTA and SEM detections, the hydration products of blast furnace slag (BFS) based cementing material SL, SLG. were studied in different age periods. The XRD analysis of cementing material SL hydration products showed that the composition of hydration products were mainly amorphous substances, few crystalline substances. Characteristic peak of ettringite hadn?t been found in the spectral line of DTA, and it hadn?t been found in the figures of SEM, either, which was accordant with the conclusion that the cementing performance of SL mainly coming from gel of hydrated calcium silicate (CSH) and hydrated calcium aluminate. However, the main hydration products of SLG are Aft, CSH, and AFm, which are similar to Portland cement. All results suggest that BFS is a suitable base material for cementation. Keywords: blast furnace slag, backfilling cementing material, hydration products, cementing performance

Sep 1, 2012

By C. V. G. K. Murty

Sillimanite, chemically named Aluminum silicate, 3Al2O3SiO2 is one of the three forms of alumino silicate polymorphs and commonly encountered in aluminous metamorphic, plutonic, and volcanic rocks and their weathering products. Most of the sillimanite deposits are granular and are of high grade available in coastal areas as associated mineral along with Titanium bearing minerals namely ilmenite, rutile etc. Sillimanite is one of the widely accepted raw materials for the manufacture of high alumina refractories (55-60 % alumina) or bricks. Sillimanite based refractory bricks are used for the lining of Blast furnaces, Arc furnaces, Soaking pits, Reheating furnaces of iron and steel, rotary kilns for cement manufacturing and general kilns for lime production. Considering the vast potential of unexploited sillimanite reserves in India, M/s Trimex Sands Pvt. Ltd., (TSPL)has set up a Mineral Sand Processing plant in 2010 at Andhra Pradesh with a capacity to produce about 50,000 tons of sillimanite per annum besides the production of various heavy minerals such as ilmenite, rutile, zircon and garnet. Traditionally in India, sillimanite is upgraded by froth flotation technique using Oleic acid as a collector cum frother, sodium silicate as depressant and soda ash as pH regulator. At TSPL, Conventional mechanical float cells are installed to float sillimanite. In addition to the usual problems associated with conventional cells, poor flow ability of the sillimanite concentrate is experienced in dry circuit due to the presence of sodium oleate. Fine garnet in the sillimanite concentrate contributes to high iron content in the final product, making sillimanite separation a nightmare for operators (lower recoveries coupled with inferior grades). Various efforts were made to improve the performance of the circuit such as introduction of additional frother like MIBC, optimizing the operating parameters such as pulp density, collector dosage, depressant dosage, air flow rate, pH etc., use of collector aids, stage wise addition of reagents etc. The challenges faced to produce a sillimanite product with stringent quality norms and the efforts made to improve the grade and recovery are described in this paper. Keywords: sillimanite, froth flotation, conventional mechanical cell

Sep 1, 2012

By R. Roufail

In this paper, the effect of different operating parameters of high speed stirred mill on the particle breakage mode is addressed. Morphological features of broken particles is investigated and related to the types of forces generated in the mill using Discrete Element Method (DEM). The stress intensities generated in the mill are varied by changing the agitator speed. The investigated agitator speeds were 1000, 1500, and 2000 revolution per minute (rpm). The minerals considered in this study are hard minerals (quartz) and soft, sulphide minerals (galena). The morphological features examined are roughness, roundness and elongation, which shed light on the mode of breakage during the grinding process. Particles that are rough, less round and elongated would imply that they broke via fracture, along their grain boundaries. On the other hand, the smooth, less elongated particles would mean breakage occurred across the grain, which is abrasion mod. DEM study complemented the understanding of particle breakage mechanism via tracking the types of forces applied on the particles. Normal forces imply compressive loading, which is presumed to impose fracture breakage along the grain boundaries, whereas tangential forces imply abrasion loading. Stirred mill grinding has been regarded as an attrition/abrasion process, whereas, this study showed that about 60% of total particles that are morphologically analyzed for both minerals were rough particles. Such an observation indicates that the fine product, which contain a significant amount of progeny from the coarse fractions are consistently broken via fracture. The morphology results agreed with the DEM findings, which indicated that the agitator speed, mineral type, and residence time would dictate the type and mode of particle breakage. Keywords: DEM, high speed stirred mill

Sep 1, 2012