Search Documents

By M. Surracco, M. C. Tilocca

"Mineral comminution is often a costly process which also requires high level of energy. In the course of the studies carried out by the researchers of the Department of Civil-Environmental Engineering and Architecture at the University of Cagliari, aiming at the optimization of the reduction processes, it has been experimented, among of others, the effects of high-speed water jets on minerals grinding. As far as coal is concerned, some of the solutions initially adopted are presented in this paper, which essentially relied on the water jet power only, with secondary use of mechanical actions, to reach the most modern solutions that envisage the use of mechanical energy, normally used in traditional grinding machines, in synergy with hydraulic energy transferred by water jet.INTRODUCTION Mineral comminution can be rather expensive and demand a high-energy consumption, especially for fine sizes (Austin, 1979). Further interesting perspectives in this area may be offered by comminution means aided by high pressure water jets (Ciccu 2007), whose crushing potential is currently used for several operations such as cutting different materials, rock digging and industrial cleaning. The crushing action of water jets may induce a traction stress in materials where substances of a mineral nature, especially if characterised by permeable porosity, oppose a minor resistance (Griffith, 1920). The first solutions to this purpose essentially relied on the sole energy of water jets, with a secondary use of mechanical actions (Ciccu, 1993). Results were encouraging, despite the high values of specific energy for the low capacity of treatment. However, due to the difficulty in making the techniques mainly based on hydraulic energy practically applicable to solids comminution a solution was experimented, with some interesting results, consisting in the combination of mechanical energy, normally used in traditional grinding devices, with hydraulic energy transferred through water jets, in a synergic relationship (Ciccu, 1998; Tilocca, 2016)."

Jan 1, 2018

By C. Igathinathane

Coal is the most widely used fossil fuel in the world, providing more than 25% of world?s electrical power. Since, the behavior of coal particles in crushing and grinding circuits, concentration operations, and solid-liquid separations is strongly dependent on size, a reliable and accurate measurement of particle size and particle size distribution (PSD) is a vital aspect in coal cleaning. This paper presents a method for the characterization of ground coal particles using image analysis. We utilized a machine vision (MV) approach that used a document scanner as the imaging device and a user-coded ImageJ plug-in that processed the image and automated the PSD analysis and output results in textual and graphical forms. This approach used a sum of volumes (SVolume) as weighting factor for particle length as the primary dimension of analysis and was successfully applied to ground coal. The plug-in was further improved for computational performance in this study. Mechanical sieving (MS) was also used to compare the MV results. MV results showed that the PSD of ground coal followed a uni-modal normal distribution, and the log-normal plot against particle size exhibited a linear trend for most of the range. MS results, however, had three linear segments, when the width-based sieving results were transformed to lengths by applying the shape factor (width/length), but a definite deviation between the PSD plots was observed. This study demonstrates successful application of the MV SVolume approach for PSD analysis of ground coal, which can be extended to similar particulate minerals and products. Keywords: dimension, fiji, image j, image analysis, coal, particle size, plug-in

Sep 1, 2012

By M. Saghaeian, R. Hejazi, A. Dehghani Ahmadabadi, M. Zare

"In the most iron ore beneficiation plants, reverse flotation is the best method for removing silicate gangues from final iron ore concentrate. Many previous studies show, if the major portion of impurities include quartz minerals, the flotation process is simple, but if iron silicates are dominant, reverse flotation is so complicated and mostly not very effective. In this study which was performed on the Sangan iron ore concentrate, the performance using of reverse flotation and magnetic flotation separator for elimination of silicate gangues from the magnetic iron concentrate was investigated. The operational parameters for reverse flotation are considered as: collector and frother types and dosages and also modifiers. But for magnetic flotation separator parameters were magnetic field intensity as well as overflow and underflow water rates. Results showed that reverse flotation has not a significant effect on the elimination of impurities. Because of the silicate gangues of Sangan concentrate including a mixture of quartz and iron silicates (amphibole, pyroxene and feldspar), so downgrading of the SiO2 content for the flotation concentrate was rather low and only average reduces of 20.60% were possible. But the findings of using magnetic separator was more satisfactory. Results of the weight recovery, iron grade and also SiO2 and S grades of final concentrate were better with magnetic flotation device. So at the best and optimum condition, we could reduce 51.01% of the total silicate (SiO2~ 2.19%) along with 74.66% of sulfur content (S~ 0.076%) and concentrate weight and Fe recoveries of 92.04% and 94.51% respectively, final Fe grade of 68.73%.INTRODUCTION Chemical/traditional flotation is one of the most effective methods for separating valuable particles from waste minerals, which is used in most mineral processing industries. In the iron ore processing industry, the major impurities present in iron ore concentrate include sulfur, silica and phosphorus (Bruckard et al, 2015), which are often carried out by reverse flotation methods for the removal of sulfide and oxide impurities (Donald, 1967: Araujo et al., 2005: Ma, 2012)"

Jan 1, 2018

By A. Ghadyani

This investigation was undertaken to assess the possibility of ash and sulfur removal by microbial action of high sulfur-content coal. Thiobacillus ferrooxidans and Thiobacillus thiooxidans have been used for biodesulfurization of coal. Feed samples were provided from Tabas coal mine located in Yazd province, Iran. The sample contained 28.80% ash and 2.30% sulfur. Flotation tests were implemented to optimize the effective parameters in these cells which were constant during bio-flotation tests. According to the results, obtained from various tests using Taguchi orthogonal array design (L27), the values of optimized parameters were pH at 7, 1000 g/t gas oil as a collector, 10% solid content, 15 min conditioning time, 100 g/t MIBC as a frother and 800 rev/min rotor speed. Bio-flotation tests are carried out by means of laboratory double discharge cell and mesophilic bacteria as depressant reagent using above mentioned optimized parameters. The bio-flotation experiments were conducted based on a Taguchi orthogonal array design (L9) with four variables (bacteria type, bacteria count, rotor speed of mixer and bio-conditioning time). The collected data was analyzed by using DX7.0, Minitab14.0 and WinRobust1.02 softwares for evaluation the effect of each parameter on the optimization criteria. Considering the highest combustible recovery and the lowest ash and sulfur content, the value of optimized bacteria type, bacteria count, rotor speed of mixer and bio-conditioning time were Thiobacillus ferrooxidans, 5×107 cells/g(coal), 100 rev/min and 20 min respectively. Under this condition, ash and sulfur content and combustible recovery were predicted 12.39%, 2.08% and 82.03% respectively.

Sep 1, 2012

By Benoit Clermont, Jan Lux

"Magotteaux and Anglo Platinum started a co-operation program with the main aim of establishing the optimum milling configuration measured in terms of throughput, fineness and energy consumption.For this purpose, a fully instrumented pilot milling plant, supplied by Magotteaux (Pty) Ltd, and equipped with a 0.9 x 1.0 m ball mill, was erected at Frank concentrator (Merensky Pt ore). The primary ball mills at Frank concentrator were surveyed in order to set the conditions for the base case. This data was then replicated in the pilot mill under the same configuration. Thereafter, a series of different parameters were varied in order to attempt to optimize the milling system.Some of the grinding parameters that have been studied are:•,Gate versus overflow discharge•,Open versus closed circuit•,Different filling degrees•,Different shell liner profilesOnly grate versus overflow discharge and open versus closed circuit will be discussed in this paper.It should be noted that this paper does not attempt to give a universal solution as to what milling configuration is optimum in all cases. The conclusions apply for this particular case and probably most others, but it would be advisable to consider each case on its own."

Jan 1, 2003

By E. Barsky

The composition of multi-component materials is proved to be unambiguously determined by the composition uncertainty parameter (composition entropy). At the same time, every component, depending on its content, introduces a certain value into this parameter. Quality criterion of multi-component separation is determined by the total change of this parameter for all products obtained as a result of the separation process. This parameter can unambiguously estimate both multi-product separation and complicated schemes of modern beneficiation plants. It can be used to estimate binary mixtures separation, too. During the optimization of multi-product separation, another problem arises, which is not peculiar to binary mixtures. In this case, the total efficacy depends on the order of separation boundaries, as well. In the present paper, a specific example of initial product separation into seven products by six boundaries is investigated. It is clear that with respect to a single boundary, two products only can be obtained. In this case, the separation optimum is shown to correspond to the separation of boundary-class particles equally into both products. We have also established that from the point of view of entropy, the maximal possible separation efficacy corresponds to equiprobable composition of the initial mixture, i.e., the fine product quantity in the material to be separated is equal to that of the coarse product. Three groups of experiments were carried out. In the first group, the boundaries were consecutively specified from the finest to the coarsest one. In the second group, the boundaries were set vice-versa, i.e., consecutively from the coarsest to the finest one. In the third group, no sequence was observed. At every separation stage, a boundary was specified in such a way that the separated material composition was as close as possible to equiprobable one relative to this boundary. Total efficacy was different in all the three cases. In third group of experiments, its value is the highest, which confirms the advanced supposition. The obtained results are phenomenological, ? they can be applied to any processes of solid, liquid and gaseous materials separation.

Jan 1, 2014

By Mauricio Guimarães Bergerman

At the regrind or secondary grinding stages of base metal ores, the concern about energy efficiency is usually extremely important. In general, the specific energy consumption at this stage is higher than during the primary grinding stages. In addition, a tendency of finer grinding has been observed in the new projects of metallic minerals, due to the finer mineral liberation, which leads to increasing capital and operational costs. At Vale?s new copper projects in Brazil, regrind sizes with a P80 of approximately 40 to 20 µm have been necessary. Conventional ball mills, adequate for primary grinding, usually bring about low energy efficiency with products bellow 50 µm. Vale is using the vertical mill on its copper projects ? Sossego and Salobo, in order to optimize the regrind of rougher concentrates and reduce energy consumption. This paper presents the results of industrial surveys carried out on the Vertical mill circuits of Sossego plant during its initial years of operation, and compares these results with the design criteria and laboratory regrind tests used for the mill scale up. Keywords: grinding, regrinding, copper, vertical mill, stirred mill

Sep 1, 2012

By V. Runkana, N. K. V. Nadimpalli, S. Sahu

"IsaMill™ has been in operation in the recent past for fine grinding of low grade ores to extract non-ferrous minerals. IsaMill™, typically, consists of a series of uniformly spaced identical disks mounted on a rotating shaft which is encased in an outer shell. The mill offers high energy efficiency for fine grinding and an inherent scalability. But, it encounters certain operational challenges such as non-uniform distribution of grinding media coupled with high wear rate of the disks and solid walls of the mill at specific locations—which adversely affect the mill performance. To circumvent these operational challenges, design modification of the disks through heuristics, by introducing a reduced diameter disk (RDD) at specific locations, is a common practice in industry. But there is no systematic scientific study in this regard. In the current work, we developed a discrete element method (DEM) based model and simulated for the IsaMill™ operation to study the effect of RDD on the efficiency of the mill and wear rate of the solid walls and disks. Since the first set of disks experience the high wear rate due to the high loading of the charge, the RDD was introduced at the first two disks. The simulations were performed at different diameters of the RDDs and at different media loadings. The performance of the mill was analyzed based on the power consumption, the wear rate on disks and the distribution of media particles inside the mill. Besides, the performance variables such as mean velocity of media particles and total impact energy provided useful insights into the milling operation. It was observed that the reduction in disk diameter yields lower wear rate of the disks at the cost of decrease in power draw at a constant high media loading. Whereas, when the media loading was decreased, the amount of wear and power drawn was comparable for both the most reduced and least reduced disk diameters. Therefore, there is an optimum choice of RDD for a given mill loading to maximize the mill performance while reducing the wear rate of the disks."

Jan 1, 2018

With significant increase in steel output in the world the price of iron ores has been soaring recently. Especially, there is a strong demand for iron ores in China, leading to more attentions paid to developing low grade iron ores. In this paper mineralogy of nm-of-mine hematite ore was deter-mined, and coal-based direct reduction-magnetic concentration was successfully developed to beneficiate low grade hematite ore. Mineralogy analysis indicates that this hematite ore is a super fine refractory ore, with the main valuable mineral hematite being closely associated with quartz and distributing uniformly and mostly occurring within the size of 3~5J.lITI,leading to being difficult to beneficiate due to super fine hematite and only grading 28.83% Fetotal. This hematite ore failed to be effectively upgraded by traditional processes in trial tests, such as reverse flotation, gravity concentration, and magnetic separation, or the integration of the above processes. In contrast with adoption of the coal-based direct reduction-magnetic separation process, concentrate was produced with high iron grade and metallization degree in the present work, which provides a theoretical basis for utilization of low grade iron ores. By optimization of direct reduction conditions, such as reduction temperatures, duration and mass ratio of reductant coal to iron ore, the reduced ore with 93.72% metallization degree was prepared, and then three-stage grinding-magnetic separation of the reduced ore were conducted, the final concentrate was manufactured, assaying 69.54% Fetotal and 98.01 % metallization degree, and with low content of impurities. This iron concentrate with high metallization degree produced by this process is a superior burden for converter instead of blast furnace. This process is enviromnent friendly by directly making iron using coal and iron ores instead of coke, resulting in less emissions and low production cost.

Jan 1, 2014

By H. X. Yan, J. X. Zhang, F. S. Niu

"The analysis on influencing factors of hydraulic conditions in fine hematite flocculation, such as stirring speed, stirring time and axial distance of particle size and fractal dimension of floc was investigated. Furthermore, response surface methodology(RSM) has been applied according to the Box-Benhnken center-united experimental design principle to optimize parameters of hydraulic conditions as a response index to indicate the fractal dimension of floc. The results show that when the agitation speed is 900r/min, the axial distance is 2.0cm, and the stirring time is 3.0min, the particle size reaches the maximum value of 35.44µm and the fractal dimension is 1.6594. The interaction between the axial distance and the stirring speed is highly significant, but the interaction with the stirring time is not obvious. The experimental data and model predications match well, which indicates that the established model has high accuracy and practicability. INTRODUCTION With the exhaustion of iron ore resources that are easy to be mined and the vigorous demand for iron and steel, the exploitation and utilization of fine-grained embedded iron ore resources have drawn attention from the industry and the government [1~2]. Flocculation flotation is one of the effective methods for separation and recovery of fine granular minerals. In 1975, the method was first applied and succeeded in Tilden Concentrator, USA. Flocculation and desliming became the key technology of the Tilden to raise its annual treatment capacity from 4 million tons to 8 million tons at that time [3 ~ 4]. In 2008, the selective flocculation and desliming-reverse flotation technology was successfully used to treat 2.8 million tons of Qidong iron ore. Under the conditions of 28.36% raw iron grade and 98% grinding fineness -0.038 mm, the ideal index of 62.5% iron concentrate grade and 68% recovery was obtained [5]. Dr Kitchenner of the Royal College of Mining and the Ore Processing Research Group of Wallenstein Laboratory first proposed the use of flocculation to separate minerals. After that, many scholars conducted a great deal of theoretical and practical researches, but mostly they focused on chemical theories, mathematical models and selectivity differences in the flocculation process, while the research on the influence of the pulp flow state on the separation effect in the flocculation process started later [6~9]. The results show that the motion of the agitated flow field has a significant influence on the formation of flocs. The fluid morphology will change with the change of hydraulic conditions. The change of fluid morphology will not only affect the movement behavior of particles, but also change the action of chemical agents on the surface of mineral particles[10~12]."

Jan 1, 2018

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018

By Alok Tripathy

A simulation code called SIMJIG and the user interfaces have been developed using discrete element method (DEM) and the .NET platform respectively for the jigging process. DEM platform is used for tracking of particles in the jigging operation. DEM uses the net force balance on the particles to track the trajectory of the particle. Simulation results are compared with experimental results obtained by jigging of low grade iron ore lumps. Two different iron ore samples one from Chatishgarh and one from Odisha were used for the experimental studies. The Alljig? stratification test rig meant for batch laboratory experimental studies has been used in the present work. The behavior of different sizes of material on jigging has been examined. Later, the particle size behavior during jigging at different layers of the jig bed has been studied. Further stratification profile across the jig bed has also been studied. It was observed that simulation results are matching quite nicely with the experimental results. The SIMJIG simulator developed in the present study could be used for predicting the performance of the jigging operation effectively. Keywords: DEM, gravity concentration, jigging, iron ore, simulation

Sep 1, 2012

By Takashi Furuyama, Sukeyuki Mori, Takafumi Okuma, Norio Hashiguchi

The Tower mill KD-3 is an improved version of the laboratory mills VD-1, KD-1 and KD-2 in which the classifying column has been modified to ensure a quick discharge of products from the comminution section and, on the other hand, a better separation of coarse and fine particles; the latter being collected in a cyclone with a central spiral ribbon. To level the circling airflow through the classifying column and have a strict control over the maximum size of collected particles, a series of experiments was carried out, modifying the internal structure of the column: insertion of a vertical plate, a cone, or a horizontal net. The relationship established between the maximum size of products collected in the cyclone and the duct airflow rate indicates that, independently of the latter, the insertion of a cone in the classifying column could stabilize the maximum size of products collected in the cyclone around 15.1 - 17.5µm. With a horizontal net, the maximal size could be reduced to 8.4 - 11.3µm. This occurrence might result from the collision of coarse particles blown from the comminution zone with the base of the inserted materials and their settling down the bottom of the classifying column.

Jan 1, 2003

The flotation behavior of kaolinite and diaspore using N, N-diethyl dodecyl amine (DEN12) and N, N-dimethyl dodecyl amine (DRN12) as collector have been investigated through flotation experiments. The mechanism of adsorption of two tertiary amine collectors on surface of kaolinite and diaspore were investigated by FTIR spectral, Zeta potentials measurements and calculation of molecular orbital energy. It has been found that DEN12 and DRN12 have stronger collecting power to kaolinite and weaker collecting abilityto diaspore than DDA. Kaolinite and diaspore in bauxite ores can be separated by using DEN12 and DRN12 as collectors at pulp pH below 8 and 6, respectively. The results of zeta potentials and calculation of molecular orbital energy indicated that the adsorption strength on kaolinite surface is in the order DEN12>DRN12>DDA and the adsorption strength on diaspore surface is in the order DDA>DEN12>DRN12. FTIR spectral analysis and Zeta potentials approve that the action between kaolinite and tertiary amine collector is strong electrostatic adsorption and that of diaspore is weak electrostatic adsorption in the range of pH 5~6.

Jan 1, 2014

By Yuexin Han, Jie Liu, Shuai Yuan, Yanjun Li

"In order to improve recovery efficiency of iron minerals from iron ore tailings and to reduce its connected environmental pollution, this article investigated the reducing roasting of iron ore tailing in a laboratory fluidized magnetization roasting reactor to optimize the roasting method and conditions. The examined parameters included roasting temperature, roasting time and reducing atmosphere. The parameters evaluating magnetizing roast efficiency and theoretical value were determined. X-ray diffraction (XRD) analysis was used to investigate the conversion of iron phase after roasting. The results show that the best magnetizing roast conditions are roasting temperature of 540?, holding time of 15min, and CO concentration of 20%. The magnetization conversion ratio of roasting products is over 80%, under the best magnetic separation condition, the concentrate grade of iron is 65.61 % and the recovery of iron is 83.77 %. The XRD analysis shows that Fe exists in hematite and siderite before roasting and exists in magnetite after roasting. The technique not only recovers the iron minerals from tailings with good economic benefit, but also reduces the environmental pollution of tailings accumulation.INTRODUCTION Iron ore tailings are the solid wastes generated during the beneficiation process of iron ore concentration and are one of the main pollution concerns in the mining industry (Das et al., 1996). Continuous development of the iron and steel industry has led to the increasing amount of iron ore tailings; there are over 300 million tons of iron ore tailings discharged per year (Rao et al., 2016). The huge amount of stockpiled iron ore tailings brings a series of environmental and social problems. Comprehensive utilization of iron ore tailings can not only reduce environmental load but also conserve resources, promoting sustainable development of the society. In recent years, iron ore tailings as secondary resources have received considerable attention in many countries in the word and numbers of studies on utilization of iron ore tailings were carried out, such as recycling the valuable minerals (Datta et al., 1996; Jia et al., 2013; Panda et al., 2018), used in construction material compositions as alternative source of raw materials (Das et al., 2012; Zhou et al., 2012; Luo et al., 2016) and other utilization. The iron minerals were recovery by magnetization roasting (Rao et al., 2016; Yang et al., 2013; Yang et al., 2011) and flotation (Kumar and Mandre, 2016). By comparison the reduction roasting has more advantages, but it was found that the conventional roasting equipment was inefficient, high energy consumption and un-economically applied on an industrial-scale."

Jan 1, 2018

By Sun Chuanyao, Cao Fei, Sun Desi, Zhou Dezhi

"The research applies the density functional theory and molecule design technology to design and synthesize the novel flotation collectors for copper-sulphur separation. Density functional theory (DFT) was applied to investigate the electronic properties of O-isopropyl-N-benzyl thionocarbamate (IP-BIAN) and O-isopropyl-N-ethyl thionocarbamate (Z-200). The calculation results show that both the energy of highest occupied molecular orbital (EHOMO) and the lowest unoccupied molecular orbital (ELUMO) of IP-BIAN are smaller than that of Z-200, electronegativity of IP-BIAN is higher than that of Z-200. According to the Klopman’s generalized perturbation theory, the collecting power of the two compounds is predicted to be Z-200 > IP-BIAN, the selectivity of IP-BIAN is better than that of Z-200. Then the thionocarbamate molecular is synthesized, and the compounds are characterized by nuclear magnetic resonance (NMR). It turns out that the test result identifies the prediction after the flotation verified test of pure mineral and actual mineral. The results demonstrate that the EHOMO and ELUMO are smaller in the thionocarbamate after a nitrogen atom is bound to benzyl, the thionocarbamate has strong selectivity and low collecting power. The lower the LUMO energy of thionocarbamate is, the stronger the back donation covalent p-bond between collectors and chalcopyrite is, thus improving flotation power for chalcopyrite and selectivity against pyrite. The result proves the feasibility of design and synthesis of the novel thionocarbamate through the frontier orbital properties of the collectors.1. INTRODUCTION Thiocarbamate is a kind of nonionic polar collector and is now widely used as flotation collector for copper-sulphur separation. The flotation power of thiocarbamate to chalcopyrite is stronger than pyrite, so it has high selectivity against pyrite. The frontier orbital theory and density functional theory (DFT) has been widely applied to study the structure-activity relationship of flotation collectors [1-6]. The flotation test results can be interpreted by using the reaction energy criteria and quantum-chemical parameters, such as the energy of the highest occupied molecular orbital (EHOMO) and the energy of the lowest unoccupied molecular orbital (ELUMO) of collector [7-11]. In turn, there are rarely reports about screening the novel flotation collector, by the frontier orbital properties such as HOMO and LUMO of flotation collectors. In this thesis, we apply the density functional theory and molecule design technology to design and synthesize the novel flotation collectors for copper-sulphur separation. Based on the previous findings of the structure-activity relationship of xanthogen formats [12], it has stronger collecting ability to chalcopyrite while the xanthogen formats after a nitrogen atom is bound to benzyl. Thus, in this study, a novel thionocarbamate molecule O-isopropyl-N-benzyl thionocarbamate (IP-BIAN) will be constructed, when the group structure connected with N atom in the known collector O-isopropyl-N-ethyl thionocarbamate (Z-200) is replaced with ethyl by propyl. The collectors (IP-BIAN and Z-200) have been calculated by DFT methods in quantum chemistry. By analyzing the reaction energy criteria and the frontier orbital properties (HOMO and LUMO), this research predicts flotation performance of novel collectors (IP-BIAN), then the synthetic experiments and flotation verified tests are conducted. The research provides a new theory reference for screening out the high-effective flotation collectors of copper-sulphur separation. This technology adoption will contribute to the sustainable development of mineral resources as it shortens the research cycle of new collector molecules and reduces the investment."

Jan 1, 2018

By David G. Hulbert, Daniël J. Oosthuizen, Bernard Muller, Daniël de V. van der Spuy

"Expert Online is a software system that makes use of novel artificial intelligence technology, known as the Interpreting Expert System (IES), to mimic an informed expert on a minerals processing plant. Previous implementations of the IES were only capable of explaining the controller actions. Expert Online will also take on the more difficult task of explaining the complex process behaviour to the operator in simple language.The primary functions of Expert Online are to serve as a training tool and an online assistant to operators. However, it is also expected to be of value to supervisors and plant managers.A number of additional features are envisaged, including different operating modes, fault detection, speech synthesis and advanced message filtering. Expert Online will increase the operator’s knowledge of the process and his/her understanding and acceptance of the complex control systems. Users would be supplied with relevant and timeous information required to make informed decisions to ensure smooth plant operation.This paper discusses the structural design of Expert Online for implementation on the latest version of MINTEK’s open control platform, PlantStar, as well as several advances and additions since the previous implementations of the Interpreting Expert System."

Jan 1, 2003

By Qidong Zhang, Yongsheng Song, Wenjuan Li, Guiying Zhou, Kun Song

"Molybdenum is a very important rare mineral resources, which exists largely in oxidized ores and sulphide ores in nature. About 99% of metallic molybdenum comes from molybdenite. The talcose molybdenum resources are abundant but the resources utilization is low, because the talc is naturally hydrophobic and the floatability of talc is similar with molybdenite, which lead to difficult separation by flotation. Talc is easy entry into concentrate in flotation which can cause the content of MgO overhigh, therefore the molybdenum concentrate grade can not meet the industrial requirements. Thus the utilization level of talcose molybdenum resources has been restricted greatly.The adsorption of water on talc and molybdenite surfaces and natural floatability of minerals were studied by density functional theory method. The results showed that molybdenite and talc were layered minerals which exhibited similar surface wettability and H2O molecule prefers to stay with water rather than the minerals surfaces. N2 is adsorbed on talc and molybdenite surfaces more easily than H2O. The interaction and flotation behavior were studied by SEM and flotation experiments. The reason why talc interferes with the flotation molybdenite has been revealed. The agglomeration between molybenite and talc was caused easily in neutral or acidity solution, and it was dispersing between molybenite and talc particles in alkaline solution. The flotation results showed that good floatability of talc was the key factor causing a low grade of concentrate in alkaline solution. Thus, it is the key factor to enlarge floatability difference between molybdenite and talc.INTRODUCTIONMolybdenum is a kind of important rare metal and strategic reserve resources (Zhitao Y et al, 2016a). Due to excellent characteristic, such as high melting point, good thermal property and et al, it’s widely used in metallurgy, machinery, chemical, aerospace, and many other areas. It has become an indispensable metal in modern industry. Molybdenum generally exist in the form of molybdenite which is a kind of mineral with excellent natural floatability. Talc is a kind of typical hydrous and layered magnesium silicate minerals (Beattie D et al,2006a), which is one of the most common gangue mineral of the platinum group metal ores and metal sulfide ores (Tao L et al,2011). Due to its good native floatability, talc is easy entry into the concentrate product with foam in the process of sulfide ore flotation (Kelebek S and Smith S, 2006b), which resulted in decreasing concentrate indexes. Not on that, the high-content MgO of concentrate will also produce a series of adverse impact to the subsequent smelting (Lotter N O et al, 2008). Therefore, it is difficult to separate talc from sulfide ore concentrate effectively."

Jan 1, 2018

By L. Tong

Stirred milling of laterites offers possibilities for improving liberation and selective size reduction of soft nickel-bearing minerals in laterites. Batch grinding tests were performed in a Netzsch LME4 stirred mill on a siliceous goethitic (SG) nickel laterite sample (-2000 µm particle size) to evaluate the effect of operating conditions such as stirrer speed, grinding time, pH, solid content, water salinity and charge volume. The target was to produce a -38 µm fraction in the milling product with high nickel recovery and grade. Addition of dispersant (sodium hexametaphosphate) was also optimized with respect to the rheology of the slurry. In terms of stress intensity, the optimum grinding conditions for selective size reduction were: 1000 rpm, 50 per cent charge volume. At higher stress intensity (2000 rpm), Ni recovery in the -38 µm product was higher, but Ni grade was low, due to the breakage of the harder siliceous particles. Decreasing the yield stress by modifying slurry pH or adding dispersant improved the rheological properties of the pulp, but had no great influence on Ni upgrade in the fine product. Modifying water salinity by adding 2 M NaCl had also little effect. The breakage of the +38 µm particles in the feed determined Ni upgrade greatly. Ni grade in the -38 µm product decreased with grinding time, suggesting that the Ni-bearing minerals break first, while the harder siliceous minerals have a lower breakage rate. The breakage rates with respect to sample mass for Ni, Mg and Si indicate that: Mg > Ni > Mass > Si. The optimum grinding time for the highest Ni upgrade was 0.25 min. The Ni grade increased from 0.88 per cent to 1.35 per cent (upgrade 54 per cent), with 24 per cent Ni recovery. Keywords: fine grinding, stirred media mill, nickel laterite, slurry rheology

Sep 1, 2012

By Aline Tavares

This paper describes the investigative studies carried out at Vale´s Center of Mineral Development (CDM) for a nickel sulfide deposit aiming to develop an adequate flotation flowsheet. The CDM facilities comprises of very well equipped laboratories to develop hydrometallurgical, comminution, flotation, physical separation processes, besides chemical and mineralogical laboratories, that are required to accomplish pre-feasibility studies, new process routes developments and, eventually, brownfield projects. Close association of the flotation group with the geometallurgy and the mineralogy teams play a key role during greenfield project development. Most of the information required by process engineers responsible for the flowsheet development can be provided by the mineralogy team and its mineralogical laboratory at CDM. During the flowsheet development of this nickel sulfide deposit, two ore types were identified as the most abundant in the deposit, named biotite-chlorite hydrothermalite (HID) and magnetite hydrothermalite (MAG HID). Six samples were selected for the investigative studies based on this initial information. Nickel grade varied from 0.39% to 1.95%. The main nickel-bearing minerals were millerite and pentlandite whereas the main non-sulphide gangue minerals were quartz, plagioclase, biotite, chlorite, actinolite, and/or magnetite. Electron microprobe (EMP) identified the presence of nickel in solid solution in gangue minerals such as biotite, chlorite, and actinolite. Nickel deportment in silicates varied from 3% to almost 40%. Magnesium was distributed in biotite and chlorite, except in sample MAG HID, in which talc was responsible for almost 50% of the Mg content. Liberation studies indicated that the optimum feed grind size was around 150µm and that pyrite occurred highly associated to the nickel sulfides. The flotation tests were planned based on the information provided by the mineralogical data. Rougher flotation tests indicated that the optimum P80 of the primary grind was 212µm for the HID type and 150µm for the MAG HID. From the reagents tested, amyl xanthate proved to be the most efficient in the recovery of the sulfides. In the MAG HID sample talc was well depressed by dosing 600g/t of CMC. Nickel recoveries in the rougher stage were lower than 90% due to the nickel distributed in silicates. However, sulfur recovery was around 95%, indicating high recovery of the total sulfides. Open circuit and locked cycle tests were conducted to evaluate the effect of the regrind size in the nickel grade and recovery (P80 of 44µm and 20µm). Nickel recovery decreased from 70% to 65% when finer regrind size was tested. Although nickel recovery decreased by 5%, the finer regrind size lead to a higher Ni grade (from 11% to 23%Ni) and lower fluorine grade (from 1138ppm to 700ppm) in the concentrate. Keywords: nickel sulfide, flotation, mineralogical characterization, flowsheet development

Sep 1, 2012