Search Documents

By Leming Ou, Hongqiang Li, Li Zeng, Qiming Feng, Yiping Lu, Guofan Zhang

"The entrainment of sericite, especially in the presence of hydrophobic microcrystalline graphite, leads to the poor flotation selectivity of microcrystalline graphite ore. In this paper, it was attempted to reduce entrainment of sericite, selective flocculation of microcrystalline graphite using polyethylene oxide (PEO) was studied. For the sake of flocculate microcrystalline graphiteselectively, flocculation tests of microcrystalline graphite and sericite single mineral were conducted.To investigate the effect of selectiveflocculation of graphite on entrainment of sericite in microcrystalline graphite flotation, batch flotation tests of graphite single mineral and artificial mixtures were conducted; theflocculationselectivity of PEO of different molecular weight (M.W.) was alsocompared inartificial mixture flotation. Inthe end, the structure of flocs in different particle size was studied by sieve analysis and microscopic observation. The resultsindicated that PEO of molecular weightone million andtwo million could selectivelyflocculate the microcrystalline graphite and reduce the entrainment of sericite at a lower dosage; further increasingof the dosage of PEO(M.W. ?two million) led to hetero-flocculation between graphite and sericiteandmadethe ash content of concentrate increase again."

Jan 1, 2014

Poor floatability of fine particles is known to be the main cause of the low recovery of ilmenite in Panzhihua, which is the largest titanium mine of China. To get an optimum ilmenite recovery, selective flocculation, and flotation of fine ilmenite was investigated through flotation tests, particle size analysis, zeta potential tests and scanning electron microscopy. The results indicate that carboxymethyl cellulose (CMC) shows flocculation effect for both ilmenite and titanaugite without selectivity, while selective flocculation could be realized by the combination of water glass and CMC. It is because that competitive adsorption would take place on these two kinds of mineral when water glass and CMC are used together. On the surface of ilmenite, the adsorption ability of CMC is stronger than that of water glass, so that CMC can absorb to the same extent irrespective of the presence of a pre-adsorbed layer of water glass and ilmenite particles is flocculated by CMC. The same cannot be said of the titanaugite phase as water glass strongly adsorbs onto the titanaugite, and the adsorption of CMC is hindered. Therefore, the titanaugite particles keep dispersion. Furthermore, the flotation of fine ilmenite particles is feasible as the ilmenite floccules could react with sodium oleate. In the flotation separation of Panzhihua ilmenite ore, the recovery of TiO2 increased from 52.63% to 68.28% by selective flotation. Keywords: ilmenite, flotation, selective flocculation, adsorption

Sep 1, 2012

By Volker Vogt, Wolfgang Sand, Eberhard Gock

"It was discovered that the selective activity of bacteria during the extraction of raw material concentrates by means of flotation could also be achieved with extracellular polymeric substances (EPS) excreted by bacteria. EPS, which is extracted by means of centrifuging bacterial cultures, can help to significantly reduce the use of cyanides, approximately 200,000 t/a of which are used for ore dressing today.The bacterium used was Acidithiobacillus ferrooxidans. In order to identify the bandwidth of the oxidation activity, 20 bacterial strains of the strain collection of the University of Hamburg were attracted to iron(II) sulfate and pyrite under defined conditions. All strains oxidized iron(II) sulfate ten times faster than pyrite.EPS has so far been derived from four strains. In general, EPS extracts are divided into a hydrophilic and a hydrophobic fraction. The hydrophilic fraction is composed of e.g. fucose, rhamnose and glucose; fatty acids such as dodecanoic acid, hexadecanoic acid, octadecanoic acid and nonadecanoic acid were found in the hydrophobic fraction.Pure mineral phases and mineral mixtures were used for the flotation tests. As opposed to current knowledge, the results were reproducible with technical flotation machines."

Jan 1, 2003

By S. K. Dutta

Enormous amount of iron ore fines is generated, due to partly soft and friable nature, during mining. Coal fines are also produced during their processing. These fines cannot be used directly in ironmaking reactors. Utilization of these fines for extracting metal is of vital concern for resource conservation and pollution control, and therefore, a novel concept of agglomeration by cold-bonding is developed. Composite briquettes/pellets of iron ore fines with coal fines were prepared in the laboratory by cold-bonding technique. Various binders such as lime, Ca(OH)2, slaked lime, dextrin, molasses, fly ash etc were employed either alone or in combination in different proportions for making composite briquettes/pellets. It was possible to obtain dry strength of composite briquettes more than 300 N/briquette in some cases and more than 200 N/briquette in many trials. The combination of fly ash with slaked lime and molasses produced the highest strength, more than 400 N/briquette. Drop strength and shatter index values of composite briquettes/pellets were also measured. In briquettes, best compressive strength (978 N/briquette) is observed by using polyvinyl alcohol (PVA) binder. In pellet, best compressive strength (362 N/pellet) is achieved by PVA; shatter index (0.1%) and dry drop strength (158 numbers) are also good. Compressive strength above 200 N/pellet is obtained by fly ash, slaked lime and molasses combination.

Sep 1, 2012

By Sunil K. Tripathy

Particle characteristics such as size, density, liberation and magnetic susceptibility play vital role in magnetic separation technique. To understand the performance of magnetic separation process for chromite beneficiation industry, particle characteristics need to be analysed. However, to date, this has been an expensive and time consuming task, thus only minimal amounts of this type of data are available in the literature. Several new methods are being developed, that will produce the required mineralogical and liberation data to provide processing information rapidly and inexpensively. Among these, QEMSCAN is a unique and advanced characterisation equipment used for liberation analysis for different ore whereas S.G. Franz Isodynamic Separator for determining the magnetic susceptibility. In Indian chromite deposits, the content of iron bearing minerals in the ore is typical which controls the Cr:Fe ratio in the product while treating in gravity based beneficiation plant. In the present investigation, detailed characterisation of two distinct chromite ore samples from Sukinda chromite deposit, India, was investigated which includes advanced mineral characterisation using QEMSCANand magnetic susceptibility measurement by using Frantz Isodynamic separator, etc.. Presence of haematite and gibbsite along with chromite mineral were identified as major gangue minerals in the high grade ore from XRD pattern whereas Goethite, Quartz, Haematite, Kaolinite, Ringwoodite identified in the low grade ore. The mass magnetic susceptibility of low grade ore is very high 5.2 cm3/g compared to 2.7 cm3/g for high grade ore, due to the presence of abundant quantity of iron bearing minerals. Subsequently, these two types of ore were subjected for magnetic separation for improving Cr:Fe ratio by using different magnetic separators viz. induced roll magnetic separator, wet high intensity magnetic separator, rare earth roll magnetic separator, rare earth drum magnetic separator. The results of magnetic separation studies indicated that, Cr: Fe ratio of the chromite ores can be improved to 3.99 and 1.97 from the feed assaying 3.09 and 1.29 respectively. Studies on rare earth roll magnetic separator indicated that both the ores were upgraded to a maximum Cr:Fe ratio level at optimised condition. Keywords: characterization, QEMSCAN, magnetic separation, rare earth roll magnetic separator, industrial mineral, chromite

Sep 1, 2012

By S. M. H. Haddad, M. Saghaeian, R. Hejazi

"Due to limited water resources in mineral processing plants, increasing the efficiency of iron tailing dewatering system in order to obtain more usable water is very important. In this research, flocculation process, as one of the best method for water recovery, was investigated by using one organic cationic and three anionic types of flocculants with different dosages (10, 20, 30 g/ton) and iron ore tailing slurry (8 % w/w solidity) in series of graduated cylinders and obtained results were compared. it is observed that for tailing sample, the anionic flocculants have a significant effect on the settling rate of solid particles compared to the cationic types. Furthermore, effects of temperature (10, 23 and 43 ºC) and pH (2, 7 and 12) on the rate of settlement and turbidity was studied by utilizing the best flocculant. Findings showed that by increasing the amount of flocculant dosage, sedimentation rate went up and turbidity decreased. Comparison the out-put data of tests indicated that at temperature 23 °C and pH=7, the best results for both of faster settling rate and producing more clear water were reached. It should be considered that lower temperature has a more negative effect on the sedimentation rate and overflow water quality. So it will be predicted that for cold seasons, the consumption of the flocculant powder would be higher than the moderate or warm seasons. Also, coagulation/flocculation was evaluated by applying organic cationic coagulant added to anionic flocculant in three different times. Different ratios of coagulant to flocculant was examined (70%:30%, 50%:50%, 30%:70%) as well. Overall, utilizing coagulant had desirable influence on sedimentation experiments and obtaining high quality water. 1- INTRODUCTION In mineral Factories, among the important processes, solid-liquid separation process due to limited resources of water is very important and operates on iron ore tailing in settling tank as thickener in order to gain clear water for preventing water loss and applying again in plant units (Ciftci and Serhat Isik, 2017). Iron ore tailing include inharmonious compounds of iron oxides, silicates and aluminum-silicates. The percentage of solid in the tailing usually changes between 5 and 10 percent (Dash et al., 2011). One of the major problem about dewatering of tailing in thickener is solid-liquid separation of slurries with high stability because of fine particles. It means that rate of sedimentation is very slow and recovered water quality is inappropriate. This issue can be solved to a large extent by factors such as pH control, ionic strength and flocculation/coagulation process which results in aggregation of particles so that settlement by gravity is happened (Dash et al., 2011)."

Jan 1, 2018

This article takes the OMRON C200HE PLC for example introducing its application in mica-paper production equipment, including style selection, address assignment of I/O point, and programming for different function. In the transformation process of simulated data and digit data, the corresponding relations between two data and so on are also discussed.

Jan 1, 2014

By J. Masinja

The mining industry is known to be a potential major contributor to the industrial development of any economy. Large-scale mining has been going on in Zambia for the last 100 years. The impact of mining in Zambia has been to create a development corridor along the line of rail to the Copperbelt Province, where hitherto, mining was concentrated, and then to develop a large consolidated high-density economic zone covering an area of about 72 km by 60km. This area is home to a number of very large integrated copper/cobalt mining complexes. The mining zone has expanded to the Northwestern Province in the last 10 years, where the largest copper mine in Africa now exists, having produced about 300 000 tonnes of copper in 2011. The total output of the Zambian mining industry is now about 820 000 tonnes per annum with projections of reaching 1.5 million by 2015, due to new Greenfield investments expected to come online by then. These new mining industry developments have come on the back of strong and sustained high base metal prices, in the last 10 years or so, due to demand mainly from China and India. This new lease of life has increased the contribution of the sector to the national treasury. The mining industry in Zambia has undergone a very important ownership restructuring with the sale of the previously Government owned parastatal, Zambia Consolidated Copper Mines (ZCCM) which dominated the sector, to allow for private sector participation. The privatization process lasted from about 1995 to about 2002. The recent growth of the mining sector has unfortunately not been matched by an adequate supply of skilled manpower for various reasons. These include: (i) A lack of strong in-house training strategies by the new mine owners (ii) Decrease in industry support to the training institutions (iii) The demise of and restructuring of ZCCM which has consequently limited the Government human resources planning tools for the mining sector (iv) The cyclic nature for the fortunes of the sector has lead to fluctuating interest of student recruitment into training institutions (v) Limitations, both staff and equipment, in the training institutions (vi) A re-structuring of the training institutions This paper examines the current status, and student output from tertiary training institutions for the mining sector in Zambia. This is then compared to the skilled labour demands of the sector. The various cause and effect issues are considered and a proposal on how this skills gap could be addressed sustainably is proposed. Keywords: skills gap, graduate training, quality of graduates

Sep 1, 2012

By D. P. Chakraborty

Joda East Iron Mine, one of the captive iron ore sources of Tata steel, located in the state of Odisha in eastern India caters to approximately 45% of the iron ore requirement of the Jamshedpur Steel Plant. The iron ore occurring in the mine having high in iron content along with high in alumina. Clay and gibbsite are the predominant mineral phases present as surface coating, fracture filling and/or free occurring and are responsible for alumina content higher. Alumina in iron ore impacts the techno-economic performance of a steel plant by impacting sintering and blast furnace productivity. The impact is even higher when it comes to fine ore used in the blast furnaces in the form of sinter as it constitutes a major portion of the blast furnace burden. Therefore, it is beneficial to upgrade iron ore in the mine head and to reduce alumina before it is subjected to agglomeration. Mineralogical test works reveal, that alumina in iron fines is mainly associated with the clay attached to the hematite particles, either free or interlocked to a very fine size. The paper describes the efforts made to reduce alumina in the iron fines in Joda East processing plant, without much of capital investment for a very sophisticated fines beneficiation circuit. In this process, a suitable dispersant was added in the plant that dispersed the masked slime coating over the iron ore fines, thereby making a better quality iron ore fines with reduced alumina content. The alumina in fines improved by 0.2 units? means from a label of 2.4-2.6 % reduced to 2.2-2.4 %. With this initiative, not only the primary objective of alumina reduction is met but also it has given substantial benefit in reduction of silica and as well as moisture in product. This moisture reduction also has given bottom line impact by reducing idle freight and royalty.

Sep 1, 2012

By J. Menuge, G. Barker

"Liberation (QEM-SCAN) and surface chemical (time of flight secondary ion mass spectrometry -ToF-SIMS) analyses have been undertaken on plant Pb circuit flotation samples with the aim of defining the factors resulting in sub-optimal recovery. Lead flotation circuit feed, cleaner concentrate and tails samples were examined on a size-by-size basis using QEM-SCAN. Sulfide minerals accounted for approximately one third of the flotation feed with pyrite making up 16 wt.%, followed by sphalerite (13 wt.%) and galena (3 wt.%). Non-sulfide gangue minerals comprised calcium carbonates calcite (26 wt.%), dolomite (14 wt.%) with quartz, feldspars and barite all contributing > 5 wt.%. QEM-SCAN analysis indicated that liberation was not the primary cause of the poor flotation response. Principal component analysis was applied to the ToF-SIMS data derived from five samples (as for QEM-SCAN plus rougher concentrate and tails) to enable identification of correlated surface chemical components. Although a significant range of correlations were observed we focus here on those that show a discernible pattern throughout the float circuit. It was found that for the flotation feed the surface of galena were largely obscured but where Pb was observed there was a strong correlation to surface Fe. For the rougher and cleaner concentrates the galena surfaces were relatively clean with no correlation to Fe for the rougher concentrate and minor correlation in the cleaner concentrate. However, in the rougher and cleaner tails the clear correlation of galena with Fe was again apparent. These results suggest, in combination with prior studies of pyrite morphology, that the principal factor effecting grade is the rapid oxidation of the framboidal pyrite resulting in the contamination of the galena surface with a high loading of hydrophilic oxidised Fe species, thus depressing flotation."

Jan 1, 2014

By E. V. Koporulina, I. Zh. Bunin, M. V. Ryazantseva

"We studied the mechanism of structural and chemical transformations of columbite, tantalite, zircon and feldspar surface during the treatment by high – power electromagnetic pulses (HPEMP) using the methods of X - ray photoelectron spectroscopy (XPS), analytical electron microscopy (SEM - EDX), Kelvin probe force microscopy and flotation experiments. According to XPS and SEM - EDX data, major changes in the atoms chemical state of investigated minerals surface are related with formation and modification of functional cover and changing in concentration (% at.) of hydroxyl groups on the mineral surface, leading to increase in the contrast of technological properties of the rare metals minerals. Research has identified the optimal parameters of HPEMP - treatment of rare - earth minerals Npuls ??104, Ttreatment ??100 sec. improving the selectivity of the flotation separation of columbite and zircon. The difference in mineral recovery into the froth (? e) before and after HPEMP - treatment was about 11 % and 24.5 %, respectively. No significant increase was observed in the flotation activity of feldspar. This study's findings demonstrate the effectiveness of HPEMP - treatment in inducing a controlled change in the structural and chemical properties of rare - earth minerals and improving the process efficiency for the processing of rougher tantalum - niobium gravity concentrates.INTRODUCTIONThe importance of improving the processing methods of tantalum-niobium ores and concentrates is explained by the mineralogical properties of rare - earth ores. These are properties such as the variable mineral, chemical, and grain size composition, complex morphometric properties, and the dissemination of ore mineral grains of micro - and nanometric size. Iron oxide and hydroxide films on the mineral surfaces neutralize the surface physicochemical and absorption properties of the minerals. Both in Russia and globally, nonconventional (non - mechanical) methods are being developed based on physicochemical, electrochemical, and pulsed energy impacts to improve the efficiency of disintegration and liberation processes of disseminated mineral complexes and to enhance the contrast of the structural, chemical, and technological (floatability) properties of refractory ores. This study is devoted to the investigation of the applicability of high – power electromagnetic pulses (HPEMP – treatment) for the change in the structural and chemical properties of rare - earth minerals and improving of the flotation properties contrast."

Jan 1, 2018

By S. Sarioglan

The bleaching of edible oils, industrial oils, and some chemicals may be achieved using natural and acid-activated clays. These materials remove impurities and pigments from the oils. In this work, a bentonite clay from Turkey (Somas bentonite) was activated with different concentration of H2SO4 and HCl at 70~90°C and 5~8 hours. Under these conditions several cations were removed from natural bentonite (Al, Mg, and Fe) and DTA-TGA, FT-IR curves of the solids obtained after acid treatment were examined. Treatment time and acid concentration increased the degree of destruction of the bentonite structure which was determined by ICP. Activated samples were tested in order to verify their capacity to bleach soybean oil and compared to standard commercial bleaching clays. The experimental results indicate that treated samples with H2SO4 have the same efficient in bleaching crude soybean oil with the standards and treated sample with HCl is more efficient in bleaching than the commercial products.

Jan 1, 2014

During incineration of municipal solid waste (MSW), various environmentally harmful elements and heavy metals are liberated partly into bottom ash, and partly carried away with the off-gases and subsequently trapped in fly-ash. If these waste incineration residues are not properly processed and immobilized, it can lead to secondary environmental pollution to the air, soil and water. The stricter environmental regulations require a higher immobilization efficiency of the waste incineration residues, which is the main objective of the present cooperation research. Within the present project, a systematic scientific research on various MSWI residues has been carried out, including sampling, low or high temperature processing and leaching tests. In the present paper, the major results have been summarized. The research results reveal that through appropriate combined pre-processing and high temperature vitrification, the bottom ash and fly ash can be efficiently stabilized. The results achieved provide a valuable alternative route to treat the solid residues from incinerators, and to make efficient recycling and safe utilization possible.

Jan 1, 2014

By Haragobinda Srichandan

The present study aimed to investigate the bioleaching efficiency of moderate thermophilic microorganism in a growth medium without Fe supplement on three different size fractions of spent catalyst obtained from petroleum refinery. All the experiments were conducted on shake flasks at a temperature of 65 °C and a pulp density of 10% (w/v) on three size fractions viz. 45-106 µm, 106-212 µm and >212 µm and a working volume of 100 ml comprising of 10 ml of microbial inoculums and 90 ml of Modified Kelly medium. The parameters like pH, redox potential, viable planktonic cell count and the amount of acid addition was measured and quantified on regular basis to follow the progress of the bioleaching. The pH varied much in the lag and logarithmic phase of the experiments but stabilized toward the stationary phase. The total acid additions in each batch experiment were determined the amount of Conc. H2SO4 requirement, which ranged between 683-757 kg/ton of spent catalyst. The redox potential values ranged between 625-650 mV, Ag/AgCl, but were very low ranging between 350-450 mV during initial period. The planktonic viable cell count ranged between 108-109 cells/ml active in the bioleaching system, without any toxic influence of the spent catalyst, but initially due to fall in redox potential and new environment for the microbes, their population was low. The leaching yield of Ni was found to be promising with very high leaching yield of 92-96% followed by Al as 61-62%, which means both Ni and Al leaching were favored by the moderate thermophilic bioleaching compared to the mesophilic bioleaching. There was very little difference in the leaching yield, when compared with different size fractions and hence grinding can be avoided prior to leaching. This process seems to be economical as no Fe source is supplemented together with no requirement of grinding and over all a biological process resulting for an eco-friendly process for future optimization of the metal recovery from petroleum refinery spent catalysts. Keywords: bioleaching, spent catalyst, thermophile, 9K medium

Sep 1, 2012

By J. E. Gebhardt

Progress is reported on capturing the effects of gangue chemistry in the context of a comprehensive stockpile heap leach model for leaching copper sulfide ores, employing leading edge computational fluid dynamics (CFD) technology. The stockpile is a complex multi-phase process, comprising of a solid porous media, with complex fluid flow, gas and liquid phases, competing solid-liquid reactions, dissolution of minerals and transport through the heap. The model accounts for many of the challenging physical and chemical features of the heap, including transport and reactions kinetics for the important copper and iron sulfide minerals, ferrous oxidation, bacterial effects, thermal energy, acid and sulfate balances. In this contribution, the model has been extended to incorporate dissolution of various species from gangue reactions and precipitation of hydronium and potassium jarosite, ferric hydroxide, alunite, and gypsum. The effect of aeration on the simulation of a copper sulfide heap leach is provided as an example.

Sep 1, 2012

By Zhazira Baltabekova, Nina Lokhova, Arailym Dukembayeva, Madali Naimanbayev, Zhantore Dzhurkanov

"Recycling of industrial waste provided they have enough valuable elements requires significantly less investment compared with ore processing. Promising man-made raw material of rare earth elements (REE) is phosphogypsum. Works performed on dismantlement of phosphogypsum only concern phosphogypsum processing from apatit. In this case, none of the developments was tested for phosphogypsum produced on the basis of phosphorus, chemical and mineralogical composition of which is markedly different from apatites. We studied phosphorites of the Karatau deposits (Kazakhstan). Mineralogically all the layers are composed of three main ingredients: phosphate, silica and carbonate, which account for 92-96% of the weight composition of ores and rocks. Of impurities there are pyrite, iron hydroxides, gypsum, fluorite. In addition to the actual composition of phosphate in phosphate ores there are apatite. Silica is presented by chalcedony and quartz, and carbonate by calcite and dolomite. The results of X-ray microanalysis showed point cluster of grains containing REE in samples of phosphate ore. Analysis of the grain showed that REE are in the form of phosphates and silicates, which according to numerous studies in apatites is not established. In this regard, phosphogypsum, waste of production, is different in composition too. Therefore, transfer of techniques proposed in the methods for extracting REE from phosphogypsum after processing apatite, did not give the stated results and required a new approach to solving this problem. It should be noted that the phosphogypsum produced by processing the Karatau phosphorite contains medium group of REE by 2.6, and heavy group by 7.8 times more than phosphogypsum from processing the Kola apatite. Given the shortage of medium and heavy REE research to develop ways to extract the lanthanides from phosphogypsum after processing phosphate rock is promising. The study contains results of studies on the extraction of REE from phosphogypsum after Karatau phosphorite processing."

Jan 1, 2014

By S. L. Gao

Based on the differences in hardness and density of diaspore and aluminosilicate minerals which usually exist in Chinese diasporic bauxite, It is analysed that bauxite of this kind is difficult to be separated effectively by classification and normal gravity separation, and cyclonic centrifugal field was thus proposed to be carried out, in which classification can take place according to the size difference resulted from selective grinding, what?s more, the separation function according to density difference is expected to take effect at the same time, and then cyclonic separation tests for diasporic bauxite of A/S 4.39 and grinding 61.90% -0.074mm were carried out tentatively. The results showed that the accretion of feed pressure can offer strong enough centrifugal force for cyclonic separation with result that separation function according to density difference is effectively intensified, by the increasing of this parameter, underflow and overflow of A/S 7.64 and 2.18 can be processed at the same time, and the recovery of Al2O3 in underflow is 71.78%; judging by the flow ratio, the spatial locality envelope of zero vertical velocity do constringe to the vertical axis by the enlarging of diameter ratio of apex to vortex, overflow and underflow of A/S 2.08 and 6.5~7.0 can be processed by controlling this structural parameter, which is possible to offer a technological method for low-grade bauxite to de-sliming beforehand.

Jan 1, 2014

By T. J. Chen

Stone coal containing vanadium is an important vanadium resource in China. Roasting and oxidation of vanadium is the foundation for extracting vanadium from stone coal. This article takes stone coal vanadium ore in Tongshan of Hubei Province as research target to conduct oxidation roasting test on it by using a self-developed low-sodium compound additive and a new optimized technology. Firstly, use potentiometric titration, X diffraction, energy spectrum and electron probe to study valence change, occurrence and phase transition of vanadium during oxidation roasting process. On this basis, primary work is done on oxidation kinetics of vanadium by exploring the steps that control reaction rate during vanadium oxidation process and determining the related dynamic parameter ? apparent activation energy. The study shows that occurrence of vanadium in stone coal of Tongshan is mainly in illite, and that the result of phase transition in roasting process is disappearance of illite containing vanadium, formation of soluble vanadate and potassium feldspar, albite. It further demonstrates that oxidation process of vanadium is step by step (V(?)? V(?)? V(?)), and its oxidation reaction is controlled by diffusion kinetics whose dynamic apparent activation energy is E1=81.19kJ.mol-1.

Jan 1, 2014

The ultimate goal of a mineral processing plant is to recover as much of the target mineral(s) as possible from the ore being treated to achieve the best economics. Selection of the mineral processing techniques is the most important step in achieving this goal. However, due to the complexity of the ore, the recoveries of valuable minerals may be not satisfactory even when the mineral processing technique(s) are well chosen. In other words, minerals of interest can be lost to the tailings for mineralogical reasons. For example, gold is mainly extracted from the ore by gravity, flotation, cyanidation, or a combination of these processes, and high recovery (>90%) can be achieved when gold occurs as coarse grains. However, when a refractory ore is being processed, gold extraction will be challenged by mineralogical factors, which often cause gold losses to various tailings. Mineralogical factors affecting gold recovery mainly include grain size, shape, surface coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of slow-dissolving gold minerals and the refractory nature of submicroscopic gold. Among these factors, locking in sulphide, silicate and other minerals as fine-grained gold inclusions and/or as invisible submicroscopic gold is by far the most common factor leading to poor gold recovery encountered in gold ore processing. Processing of PGE ores faces the same challenges as gold. Small grain size and locking of PGM in sulphide and non-sulphide minerals often cause PGM losses. When silver ore contains significant amounts of pyrargyrite, proustite and stephanite, silver recovery by cyanidation can be very low because of the slow dissolving kinetics of these minerals. In the processing of base metal ores, high content of pyrite, intergrowth of chalcopyrite with sphalerite and presence of clay miner-als may cause problems in recovering Cu-, Pb- and Zn- bearing minerals. Process mineralogy helps address all issues and problems related to mineral processing with predicting and trouble-shooting being two major objectives. It provides useful information on process selection, flowsheet development, recovery improvement and reagent consumption optimization. The information acquired from a process mineralogical study can be used as a guide for a metallurgical testwork program for process design or optimization.

Jan 1, 2014

Traditional mineral processing techniques are more and more difficult to recover the increasingly low grade phosphate ores today. Although bioleaching method has been attempted to process low grade ores in hydrometallurgical field due to economical and environmental reason, it has been hardly used in leaching phosphate ore at home and abroad. Strains of Acidithiobacillus thiooxidans and Acidithiobacillus ferrooxidans were collected and separated from the acid drainage of a coal mine in Anhui province of China. Ultraviolet irradiation and Microwave inducement were applied to the bacterial cultivation process to produce strains of Acidithiobacillus thiooxidans and Acidithi-obacillus ferrooxidans able to tolerate extremely low pH conditions and generate sulphuric acid by oxidizing elemental sulfur or sulphide and the mutagenesis can achieve higher leaching rate. The bioleaching result will improve more by the addition of Tween series surfactants.

Jan 1, 2014