Search Documents

By Ronel du Plessis, John C. Davidtz, Jan D. Miller

Xanthates (dithiocarbonates) have been the collector of choice for the flotation of sulfide minerals ever since the flotation process was developed and have been studied quite extensively. Recently, trithiocarbonates have been shown to be very effective in bulk sulfide bench-scale flotation. Fundamental analysis using electrochemical techniques have supported these bench-scale results, illustrating that the trithiocarbonate (TTC) collectors are more readily oxidized to their corresponding dithiolates, than the dithiocarbonate (DTC) collectors, as is shown in Figure 1.

Jan 1, 2003

By G. S. Hansford, G. E. Searby

The rate of bioleaching of pyrite at 70ºC by a thermophilic archaeal culture was measured as a function of the solution redox potential by the staged addition of pyrite to a batch system. The results were compared to the rate of ferrous iron oxidation over the same potential range to determine the applicability of the multi-sub-process leaching mechanism developed for mesophilic bioleach systems.

Jan 1, 2003

By N. T. Beukes, W. Banda

Recovery of Co from slag is a recent advancement in the extractive metallurgy of nonferrous metals. In this study a DC arc technology at laboratory scale has been applied to investigate the selective recovery of Co from slag, under three different flux types with an emphasis on influencing the activity of FeOx, SiO2 and CoO in the slag. It is known that reduction of slag by carbon is only up to a certain level after which, the recovery will depend on the chemistry of the slag, hence the need to modify the slag chemistry. Two power settings were employed to induce higher temperatures and aggressive agitation. The results were interpreted by comparing how much Co and Fe was in the slag and alloy. TiO2 reduced the amount of Fe in the product alloy compared to when CaO and CaF2 were used. The change in power did not seem to have had a major effect on the recovery although the amount of material lost to flue dust was more at a higher power rate.

Jan 1, 2003

By S. Kelebek, A. Khan, J. Caceres, D. Beckett

"Pyrrhotite in nickel-copper sulphide ores is nickeliferrous and intimately associated with pentlandite. Due to its low nickel content, pyrrhotite rejection is an important step in processing of these ores. In our laboratory, various reagents were investigated for their effect on pyrrhotite depression. Among these, a combined use of triethylenetetramine and sodium metabisulphite was found highly promising.The work described in this paper has two parts. The firs part is a summary of results obtained on process samples from the pyrrhotite rejection circuit at Falconbridge’s Strathcona Mill. The second part involves simulation of the circuit performance based on the reagent conditions used in the experimental work and the concept of split factors.Two sets of reagent conditions were evaluated. The first one involved baseline conditions, simulating the current reagent performance. The second one simulated the impact these new reagents can have on the circuit performance.The simulation results obtained under baseline conditions indicated a good agreement with the current circuit performance (Figure 1). The simulation results suggest that at practically the same pentlandite recovery and tailing grades, the circuit concentrate nickel grade can be doubled through effective pyrrhotite rejection by these new reagents (Figure 2)."

Jan 1, 2003

By Marlize Barkhuizen, Chris Aldrich

"Owing to environmental constraints, safety considerations and competitive pressures, the development of model-based process control and other automated systems have experienced considerable growth in the last few decades. Reliable process models are usually critical to the successful implementation of these systems. In complex processes, these models are often constructed from process data, as modelling from first principles may not be feasible or cost-effective.Even so, modelling or identification of nonlinear systems from historic plant data can be a daunting task and in the process industries the problem is complicated by the presence of noise from various sources, nonstationarity of the data, intermittence, such as observed in particulate flows, etc. Traditional methods, such as frequency analysis and linear modelling do not handle these systems well. Similar problems arise with the application of nonlinear theory developed over the last few decades, where much of the analysis depends on embedding of the data in a phase or pseudophase space, since these methods were not originally designed to deal with noisy systems.With singular spectrum analysis, the data are embedded in a high-dimensional reconstruction, followed by the introduction of a new coordinate system, where the origin is moved to the centroid of the reconstructed system states and the axes are represented by the dominant principal components of the states (points)."

Jan 1, 2003

By N. Ahmed

"This paper is concerned with the drainage behaviour of gangue mineral in the froth phase. Experiments were carried out in a continuous laboratory flotation cell in which froth depth and bubble size can be changed independently. The fraction of solids returning from the froth to the pulp zone was expressed using a rate constant by considering the appropriate froth regimes. A mixture of hydrophilic solids (silica) and floatable particles (glass ballotini) was used as a flotation feed. Samples of glass ballotini of different hydrophobicities were obtained, using controlled silanation. Three samples, with contact angles of 50, 66, 82 degrees, were used. The effect of the initial bubble size (pulp bubble size), concentration of gangue mineral in the froth zone, and froth depth on the drainage of silica, were also investigated.Typical results obtained from this study is shown in the figure given below. In this figure drainage rate constant for the entrained solids in the presence of particles of the three hydrophobicities is plotted against froth height. As observed, the drainage rate of the entrained solids increases considerably with an increase in the degree of hydrophobicity. Concerning the effect of pulp bubble size on the drainage rate of entrained solids, larger bubbles always give higher drainage rates due to formation of relatively loose froth structures which allows gangue particles to easily move down to the pulp zone. Conversely, smaller bubbles exhibit lower drainage rate constants, in particular at shallow froth depths."

Jan 1, 2003

By Anatoly F. Usov, Vyacheslav A. Tsukerman

"The Russian scientists have developed a new energy saving method for an efficient destruction of the sturdy and hard materials (rocks, ores, frozen soils, concrete blocks ets.) - the Electric Pulse Discharge method of materials destruction (EPD). The detailed researches of a broad circle of problems connected to development EPD-disintegration of materials of a various nature and area of use are executed. The electrical and power characteristics of process, physical fundamentals of selectivity of a breakdown and destruction are investigated, the means of electric pulse splitting and refinements of materials are developed, the technological efficiency of disintegration of industrial minerals estimated.One of the most important characteristics of the EPD-disintegration of ores is the high selectivity of destruction, which provides a large ratio of useful minerals' grains opening, and at the same time, it destroy them less. This ensures in the subsequent stages of beneficiation of ores considerable increase of the extraction and improving the quality of concentrates.The technological tests of various industrial minerals have shown a possibility the EPD-disintegration, as a process that provides the best efficiency of disclosure of useful minerals in all types of ores. Technological and economic efficiency of the method of ore beneficiation is the highest for difficult beneficiated ores with rather low extraction by existing methods. The increase of extraction in this case can reach several percents. As a rule, at a EPD-disintegration the disclosure of mineral grains happens in earlier stages of material comminution than at a mechanical comminution, and with less damage of products. This promotes a simplifying the process of ore preparation and for reducing the power consumption."

Jan 1, 2003

By Naoki Hiroyoshi, Hajime Miki, Tsuyoshi Hirajima, Masami Tsunekawa

"Acidic solutions for chalcopyrite leaching contain cupric, ferrous and ferric ions, and the oxidizing power of the solutions is indicated by a redox potential, determined by the concentration ratio of ferric to ferrous ions. This paper reviews our previous studies on the redox potential dependence of chalcopyrite leaching in sulfuric acid solutions. Leaching experiments indicated that copper extraction rate was accelerated by cupric and ferrous ions , and was higher at potentials below a critical value (critical potential) in the presence of these ions. This was in good agreement with the results of electrochemical measurements, i.e. in the anodic polarization curves for a chalcopyrite electrode, active-passive behavior was observed when cupric and ferrous ions co-exist, but the activation at low potential did not occur without these ions (Figure 1). The analysis of the AC impedance spectra for chalcopyrite electrode indicated that a high-resistance passive layer grows on the chalcopyrite surface without cupric and/or ferrous ions, and that coexistence of these ions causes a formation of another product layer and inhibits the passive layer growth at low potentials.These results are explained by a reaction model assuming the formation of intermediate Cu2S due to chalcopyrite reduction and the subsequent oxidation of the Cu2S. The critical potential corresponds to the redox potential of the Cu2S formation and the predicted values matched with the experimental results. Catalytic effect of silver ions on chalcopyrite leaching was also discussed based on experimental results and the above model."

Jan 1, 2003

By J. Broadhurst

"A number of metal supplying industries have in recent years seen the compilation of life cycle inventories (LCIs) and life cycle assessments (LCAs). The activity has largely been driven by the interest of ultimate metal users, such as the automotive industry, in the interest of designing more sustainable products. Often, the compilation of such inventories has been little more than an auditing exercise. However, the process of conducting an LCA can have more value, guiding designers and operators to points within the technology train where significant emissions and impacts originate. The LCA product can thus be used to inform on-site environmental management, and, where process data is used to construct dynamic operational models, to support strategic decision making in the realm of project planning and technology selection. LCA thus serves as a valuable tool to support the industry’s drive to support the sustainable development of the societies in which it operates.This paper reviews and compares the priorities of environmental and closure planning in the design phase, with environmental management and auditing during operation, and with green procurement of minerals and metals products. It shows how life cycle assessments of various complexities can be used to reconcile these various objectives, ensuring that the latter, critical to business success, can be addressed from the outset in a new project. The paper then reviews a case study of the use of LCA in the base & precious metals industry, where the complexity of the operation disallowed the simpler auditing process so that a detailed process understanding had to be built up in order to compile a meaningful life cycle inventory."

Jan 1, 2003

By Derek Caizergues, Hurman Eric

The principle of carbothermic reduction has been around for many years. In principle it is a simple process, yet with a multitude of problems. The temperature required to affect reduction is in the region of 2200ºC and results in aluminium oxy-carbide formation rather than metallic aluminium. From a thermodynamic point of view, reducing the temperatures of reaction which would suppress oxy-carbide formation would only be possible by lowering the total pressure of the system. A decrease in thermodynamic activity of product aluminium by dissolving it in another phase would also help preventing the formation of oxy-carbides and would also increase the yield of the reduction reaction. Thus experiments have been conducted at around 1700ºC to determine the possibility of carbothermic reduction of alumina under the presence of a metallic solvent. Total pressure of the system was reduced to around 30kPa and metallic nickel, iron, copper and tin were selected as the solvent. The highest recovery of aluminium was achieved with the nickel solvent followed by iron, copper and tin. This ranking for the first three was also in accord with the extent of negative deviation form ideality in the respective binary solutions of these solvents with aluminium. The tin-aluminium system displays positive deviation form ideality. The rate and extent of reduction was found to be highly dependent on temperature and pressure. The pseudo first order reaction rate was found to be applicable to the process in all the solvents used. Rate constants were calculated and it is also suggested that the reduction was controlled primarily by the chemical reaction rate.

Jan 1, 2003

By Dingwu Feng, Jannie S. J. van Deventer

"The effect of ultrasonication on reactions at solid/liquid interfaces was investigated by using an ultrasonic probe in two slurry systems, i.e. cyanidation of a refractory sulphide ore and geopolymerisation of metakaolinite. The surfactant dithiophosphate was used to render the gold bearing sulphide particles hydrophobic, in an attempt to induce the formation of cavitation bubbles directly at the desired surfaces. Oxygen was injected into the cyanidation system to improve the attachment of oxygen bubbles to the hydrophobic sulphide surfaces. Geopolymerisation occurs in highly alkaline solution with waste aluminosilicate oxides and silicates as the reactants. The process of geopolymerisation is believed to involve dissolution of Al-Si oxides from solid particles, diffusion of dissolved Al-Si complex from the solid surface into the gel phase, condensation of gel phase and hardening of the gel phase. It has never been investigated how ultrasonication affects the above steps in synthesising geopolymers, despite a number of papers dealing with sonochemical synthesis of materials. The introduction of power ultrasound into such slurry systems is expected to result in advanced geopolymer materials.In the cyanidation of the pyrite concentrate, the kinetics of gold extraction were significantly enhanced in the presence of ultrasound, due to the prevention of passivation and the enhanced dissolution of sulphides. Cyanide consumption was significantly reduced with ultrasonication, owing to the oxidation of soluble sulphides to sulphate, minimising the cyanide consumption by sulphides. With oxygen injection, ultrasound significantly enhanced the leaching of gold from the pyrite concentrate, as oxygen could enhance the formation of the oxidation radicals by ultrasonic cavitation. In the presence of dithiophosphate, ultrasound further improved gold leaching in the oxygen-aerated system. Dithiophosphate could selectively adsorb at gold host sulphide surfaces, and make the surfaces hydrophobic. As a result, the ultrasonication effectiveness could be enhanced through forming cavitation bubbles directly at the interfaces."

Jan 1, 2003

By Vladimir S. Zharov, Vyacheslav A. Tsukerman

"Conceptual imitative dynamic model of developing enterprises for medium and long-term period permitting to ensure coordination of interests of the enterprise and territorial environmental authorities has been developed to enable the process of the prognostication and management of a concentrating mill development, in which a symbol language and terminology familiar to the manager of the company are applied. An algorithm of practical application of this model of company development was elaborated as well as a general methodological approach to the prognostication of the development and procedures of its implementation. The general methodological approach to the implementation of the model has been defined. Within the framework of system approach, a concentrating mill is considered as a subsystem of an ore mining and processing company or a mining and smelting one. A concentrating technology is considered in dynamics, its change is determined by the task of making the company operation profitable. Technological indicators are secondary relative to financial and economical indexes. At the same time, technological and economical indexes are determined in their interrelation with ecological parameters. The elaborated model allows us to estimate all necessary economic, financial and technological indexes in their interrelation both for the company as a whole and as separately redistributed estimating the basic prognostication documents - accounting balance-sheet, profit and loss report, as well as the funds flow statement. When varying the managing parameters, all necessary result-producing financial and economical indexes are estimated and a need in and a possibility of an external funding by various sources are considered.The implementation of the model enables one to determine the required scale of production capacity, as well as the amount of raw-material resources needed. In case of shortages of the latter, there should be considered various scenarios of the production capacity enhancement or the possibility of commissioning of new sites or deposits and introduction of improved technologies."

Jan 1, 2003

By Stefan Mutz, Thomas Pretz, Jörg Julius, Frank Hilbk-Kortenbruck, Aachen, Hartmut Harbeck

"The annual global production of primary aluminium was about 22 million tons in the year 2000. This represents the second largest production rate in the world market after steel. Experts are predicting that the global demand for aluminium will rise in the near future.In contrast to other metals such as copper, the recycling of aluminium is considered relatively difficult. There are two main alloying groups, namely cast and wrought. In the case of aluminium it is important that the constituents within the scrap aluminium to be smelted are clearly identified. Within the secondary remelting process alloying does take place, but a removal of unwanted metal constituents is problematic. Therefore mixed aluminium scrap (not genuine in-house collected material) can only be used to produce cast aluminium. Thus, in other words a down-cycling of wrought (extrusions and rolled) products occurs. However, in spite of these difficulties there is an increasing trend to produce aluminium from secondary scrap (approx. 35% in Germany). Similar trends have been identified in the USA and other industrialised countries. This development is mainly caused by the high energy consumption for the production of aluminium from bauxite. Producing aluminium from scrap is saving about 95 % of the energy in comparison to the processing of primary raw materials.An improvement in sorting technology is necessary to separate wrought and cast alloys of aluminium as the absolute amount of recovery from old scrap is higher than the demand for cast.This contribution presents some alternative methods, utilizing automatic picking technologies, which will be used to separate secondary aluminium in the future. During the recent years, some major progresses have been made in automatic picking technologies for different applications in the processing of primary and secondary materials.For the sorting of aluminium scrap a special additional sensor will be necessary. The best detection will ultimately be based on online elemental analysis of single particles. First investigations in the field of laser based systems for these applications have already been performed several years ago. One of the laser based techniques is the laserinduced breakdown spectrometry (LIBS)."

Jan 1, 2003

By P. Saha, D. M. Chakrabarti, National Metallurgical Laboratory, P. Bhattacharyya, B. R. Sarkhel

The estimated reserve of the phosphatic soils at the Sukulu hills region of Uganda upto a depth of 60 meters is of the order of 200 million tonnes and analyses 10-12% P2O5. A 5-tonne sample of the phosphatic soil was received at the National Metallurgical Laboratory (NML), India for beneficiation studies. The ore occurred as a naturally degraded soil deposit and the slime contained earthy lateritic minerals which made it extremely sticky. Microscopic examination revealed the presence of limonite, magnetite (martitised), hematite and goethite as major minerals along with apatite and quartz. Presence of clay was indicated by earthy smell on moistening the sample. It was observed that getting rid of the slime was as important for adequate beneficiation of the ore, as it was difficult. Earlier studies on samples of the same ore at the NML and abroad established that it was necessary to pass the ore through a series of three stages of desliming, each consisting of a step of rigorous attrition scrubbing followed by hydrocycloning, for effective elimination of the sticky slimy coating which stubbornly adhered to mineral grains. Studies were carried out at the NML in two phases to develop a flowsheet for beneficiation of the phosphatic soil. In the first phase, reproducibility of the results obtained by employing a flowsheet developed abroad was confirmed along with suggesting some modifications of the flowsheet. Then 200 kg. of concentrate was produced following the recommended flowsheet for evaluation of its suitability for production of fertilisers. To remove the limonitic slimy coating, which stubbornly adheres to the other mineral grains, it was necessary to subject the ROM ore, after screening out the +840 micron size fraction which contained only 1.75% P2O5 , to three stages of hydrocycloning each preceded by attrition scrubbing. Then only conventional beneficiation techniques could be effectively employed to upgrade the ore.

Jan 1, 2003

By Jean-Paul Franzidis, Robert G. Coleman, Emmy V. Manlapig

"The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented mobile pilot flotation plant developed by the Julius Kruttschnitt Mineral Research Centre, the Mineral Processing Research Unit of the University of Cape Town and EIMCO, as part of the Australian Minerals Industries Research Association (AMIRA) P9 Project. Apart from being a fully operational pilot plant, the FCTR was designed to determine flotation model parameters and to develop and validate flotation plant modelling, scale-up and simulation methodologies.The FCTR was installed at WMC’s Kambalda Nickel Operation where circuit modelling, simulation and scale-up test work was performed using the AMIRA P9 flotation model as the basis of the analysis. The model parameters were obtained through metallurgical sampling, batch flotation tests and gas dispersion characterisation around the FCTR. Model parameters were determined for four FCTR circuits, each of increasing complexity. The circuits ranged from a simple rougher-cleaner configuration with no recycle streams, to a more complex rougher-cleaner-recleaner configuration with two recycle streams.Using the P9 modelling methodology, the system was analysed using four mineral species: nickel sulphide, iron sulphide, copper sulphide and non-sulphide gangue. The floatability of each mineral was analysed as two floating species (fast and slow) and a non-floating species. Mass balanced data from all four FCTR circuits were regressed simultaneously together with data from 47 batch flotation tests. Nonlinear regression was used to determine the solution. The model fit was found to be accurate with most data points predicted within experimental standard deviations. A Monte Carlo sensitivity analysis was also performed to establish the stability of the regressed parameters.Using the P9 simulation methodology, simulations of five FCTR circuits (different from the previous four) were performed. The FCTR was also operated in these five circuit configurations to obtain experimental data to validate the simulated predictions. The simulations were found to predict the recovery and grade of nickel sulphide and copper sulphide within experimental standard deviations. The prediction of recovery and grade of iron sulphide and non-sulphide gangue was less accurate. Overall the FCTR simulations predicted the changes in circuit configuration well."

Jan 1, 2003

By Markus A. Reuter, Jacques J. Eksteen

"The modelling of bath type furnaces tends to be either fundamental in nature or total empirical ""black box models"". While models of the first kind are robust, they tend to lack accuracy, in cases where they are to be used for process control, and may take an overly long in development time. On the other hand, black box models tend to lack robustness of prediction for all circumstances and tend to be limited to interpolate based on historical data. While this may very often provide short-term accuracy, the models may have problems with stability in the long term. Moreover, the model structure may not reflect any of the fundamental properties of the system and remains opaque to fundamental analysis. The aim of the model development is in obtaining a model that have robustness, high accuracy, a short development time and which is adaptive to a changing environment. The models are specifically developed for on-line decision support or control of furnaces. The modelling approach is evaluated for a chromite bath smelting furnace. The role of systems analysis, mass balance smoothing, thermodynamic analysis are integrated into one generic algorithm for bath type furnaces. Not only are fundamental process relationships such the mass and energy balances satisfied through a scientific method of data reconciliation; the proposed modelling approach allows adaptive prediction, the first step towards predictive control or metallurgical decision support.It is shown that neither an ARMAX model only, nor a purely equilibrium model only, could predict the dynamics of the process very well. However, a combination of the two approaches more than doubled the accuracy as measured by the R2. It was noted for carbon dissolved in the alloy, that the improvement in R2 in using a hybrid modelling approach was more than the sum of the R2 of the individual traditional approaches. Similar improvements in modelling performance were noted for all other species.It shows further that process dynamics may totally overshadow the effect of thermochemical equilibrium (even when the thermochemical equilibrium prediction includes the recycled alloy and slag heels as additional feeds). The exclusion of process dynamics therefore leads to erroneous results."

Jan 1, 2003

By S. K. Kawatra, T. C. Eisele

"Coal-fired electrical power generation plants produce 56% of all the electricity in the U. S., burning approximately 860 million tons of coal annually. This results in production of 58 million tons of fly ash; 19 million tons of bottom ash and boiler slag, and 23 million tons of desulfurization sludges. These are a considerable disposal problem, and it would therefore be very valuable to be able to sell these residues and byproducts as useful materials, rather than paying to dispose of them in landfills. However, utilization rates are currently very low, below 32% even for the most thoroughly commercialized combustion byproduct (fly-ash). This poor utilization rate is a result of the high impurity content of combustion byproducts, which make them unsuitable for existing markets. The experiments described in this paper were therefore carried out to study the application of mineral processing techniques to upgrading combustion byproducts.Experiments were conducted to upgrade and purify low-grade combustion products to produce highgrade, readily saleable materials. A process was developed for removing unburned carbon from coal fly-ash by froth flotation, using reagents originally developed for flotation of oxidized coals. This technique could reduce the carbon content of fly-ashes containing up to 11.1% carbon to less than 2%. The froth product was sufficiently carbon-rich that the recovered carbon has value as fuel, or as low-grade activated charcoal.Fly ash was also examined as a binder for producing iron ore pellets, primarily as a substitute for bentonite. It was found that Class F fly ash in combination with an activator (calcium hydroxide) was an effective pellet binder at dosages comparable to the currently-used dosages of bentonite clay. While the flyash worked very well alone, tests in combination with bentonite showed that fly-ash/bentonite mixtures had significantly worse binding performance than either pure bentonite or pure fly-ash-based binder. This was determined to be due to the fact that bentonite and fly ash have profoundly different binding mechanisms, with fly-ash undergoing a pozzolanic chemical reaction while bentonite binds through a physical attachment process."

Jan 1, 2003

By Glasswell K. Nkonde, Fredrick Chileshe, Steven Simukanga

Improving food security by increasing crop output is a primary objective for most countries in the sub- Saharan region. Most soils in the region are deficient in phosphorus an important nutrient after nitrogen in plant growth. Phosphates are therefore used together with nitrogen and potassium based fertilizers in improving crop production. Zambia like many other countries in the sub-Saharan region imports phosphate fertilizers for use by its farmers. However, indigenous phosphate deposits of igneous origin exist in Zambia of which the main ones are Chilembwe in Petauke district, Mumbwa sugarloaf in Mumbwa district, and Nkombwa Hill in Isoka district. If commercially exploited, these deposits could become a ready source of inexpensive phosphate for the local farming communities in the country. Previous research has shown that partially acidulated phosphate rock (PAPR) produced using Chilembwe phosphate rock is just as agronomically effective as the imported superphosphate fertilizers on food crops in most of the Zambian soils. PAPR is produced by reacting finely ground phosphate rock with only a fraction (usually 50%) of the stoichiometric quantity of the sulphuric acid required to fully convert the apatite in the rock to monocalcium phosphate thus making the process cheaper in terms of acid consumption than the poduction of single superphosphate where the apatite in the rock has to be fully converted to monocalcium phophate. The factors that affect the percentage of available P2O5 in the PAPR produced include particle size of phosphate rock, degree of acidulation, concentration of acid, process temperature profile, residence time and drying temperature. These factors were studied in a 25kg/hr PAPR pilot-plant in the School of Mines at the University of Zambia using Chilembwe phosphate rock. The PAPR pilot-plant consisted of a rotary drum granulator as the main reactor, a rotary drum dryer and a triple deck vibrating screen. Ground phosphate rock was reacted with sulphuric acid and water in the granulator to form a granular product which entered the drier. The dry product was screened into three size fractions. The 1 – 4 mm size fraction was the final product whilst the –1mm size fraction was recycled. The +4mm size fraction was sent to a crusher while the crushed PAPR was sent back to the screens.

Jan 1, 2003

By John Starkey

"The development of the SAG Power Index (SPI) Test in Canada has created a new and accurate way to measure ore hardness in a SAG environment. Coupled with the standard Bond Ball Mill Work Index Test it is now possible to determine from these two relatively inexpensive laboratory tests, the amount of energy required to grind an ore from the primary crushed size to the desired liberation size. By testing multiple samples to discover where the hard and soft ore zones are located, the representative hardness distribution for the ore body can be determined and grinding equipment selected that is capable to meet production targets for all mining areas of the deposit.Previously, it was deemed prudent to select up to 50 t samples of ore for Semi Autogenous Grinding (SAG) pilot plant tests and a second 5 t sample for metallurgical pilot plant work. The methods outlined in this paper show how the 50 t sample is no longer required for SAG design because it is better to measure the representative hardness distribution of the ore body than the hardness of a “chosen” representative sample. This is demonstrated to be true by the fact that the lower horizons of an ore zone cannot initially be accessed to recover 150mm pieces, and the bulk samples taken, rarely represent the desired design hardness of the ore. Median hardness will not yield a good result in most cases and a clear understanding of the location and extent of the hardest zones is imperative to achieve a truly successful grinding circuit design.This paper discusses two plants (Kubaka and Agnico Eagle) that have been designed using SPI and Bond with no pilot plant test backup. Both have been very successful in that they can grind design tonnage on the hardest ores in the mine. This guarantees that the mine’s profitability is protected in any mining sequence. It also allows the extra power to be converted to higher throughput on softer ores if additional cash flow is needed. The advantages from the owner’s point of view are dramatic. This procedure will be attractive as well when considering the costs for test work, and the samples for testing. Existing diamond drill core is normally used and this allows the inclusion of data from the deepest regions of the mine. In addition, it is also clear that the decision to use a crusher can now be made at the design stage of a project based on measured parameters and the estimated capital costs of alternative designs."

Jan 1, 2003

By André Mans, Frans B. Waanders

"Ferrosilicon (Fe-Si) is an important commercial material and it forms the basis of the powder used in dense medium separation (DMS) of various minerals in a minerals beneficiation process. Current losses of Ferrosilicon (Fe-Si), which is used in the dense medium separation (DMS) of iron ore at Kumba Resources, Sishen, South Africa occur due to adhesion to the separation products and also by being present in the effluent stream, due to abrasion. The losses contribute greatly to the running cost of the plant and the purpose of this project was to determine the characteristics of the unused Fe-Si and then to characterise the changes that occur during storage and the use thereof.A Scanning Electron Microscope (SEM) and Mössbauer Spectroscopy (MS) were used to investigate the characteristics of the fresh and used Fe-Si. The SEM analyses of the Fe-Si yielded a composition of 15 wt.% Si and 85 wt.% Fe with minor impurities of Mn and Cr (<1 wt. %), resulting in an ordered phase with a calculated composition of Fe2Si. The average density of the Fe-Si was found to be 7.177 g.cm-3 whilst the size distribution was determined with the d50 of the particles being approximately 30 µm. A slurry, containing 10% solids was prepared, which had a density of about 1.1 g.cm-3 and this slurry was used to conduct the various experiments under laboratory conditions at the university. Samples were taken at regular intervals from a storage container containing a lime solution as well as from a closed circulation circuit system, kept at a constant temperature of about 60°C. Mössbauer Spectroscopy yielded, for the new fresh Fe-Si-samples, a two-sextet spectrum with hyperfine magnetic field strengths of 19.9T and 30.7T respectively, and the yellow-brown froth was found to be akaganeite or ß-FeOOH.It was found that the biggest loss of Fe-Si was due to the abrasion of the particles during the DMS process. A possible change in magnetic properties was also observed, leading to further losses that could occur during prolonged use of the medium. No clear changes to the Fe-Si occurred during correct storage methods, as was initially thought."

Jan 1, 2003