Search Documents

By John P. Turner, Benjamin J. Turner

"Tieback anchors are now used routinely for landslide stabilization in the USA and abroad. It is generally understood by design engineers that friction loss over the unbonded length of a tieback anchor is inherent to the system, and such loss is permitted as long as it does not exceed a certain threshold, typically 20 percent of the post-tensioning load. However, recent experience from projects utilizing tieback anchors with unbonded lengths in excess of 150 feet has demonstrated that this criterion may be difficult to achieve, particularly in certain ground conditions. Furthermore, anchor friction loss, even if below the 20-percent threshold, has important implications for the stability of the slope that are often ignored in practice. This paper presents the results of a study in which friction loss is quantified from load test data for projects in a variety of ground conditions by means of a “wobble coefficient.” Factors that may influence the wobble coefficient are examined, and recommendations for addressing this issue in practice are presented. A recent instrumented load-test program for a landslide stabilization project in Southern California is examined, demonstrating that with appropriate monitoring controls, uncertainty with regard to friction loss can be minimized. IntroductionSteel-strand tieback anchors have been used by the geotechnical community to support shoring systems for many decades, and more recently as a means to stabilize landslides. For strand encased in grease-filled plastic sheathing, which is intended to allow the strand to elongate freely, some load can still be transferred by friction between the strand and the grease and between the grease and sheathing. The sheathing then transfers load to the surrounding grout and, in the case of ground anchors, to the surrounding soil or rock. The resulting decrease in load over the length of the unbonded zone is known as “friction loss.”A widely used criterion for ground anchor acceptance based on load testing is that the measured anchor elongation must achieve a minimum value of 80 percent of the theoretical elastic elongation, or in other words the actual elongation can be up to 20 percent less than the theoretical value. This ensures that the majority of the load applied at the anchor head is reaching the bond zone behind the assumed failure surface, since load shed within the failure mass does not contribute to stability. This criterion acknowledges that friction loss is an inherent feature of the anchor system which cannot be eliminated completely, only minimized."

Jan 1, 2017

By Michael Oakland

This paper will discuss the design analysis of sheet pile cofferdams for static and dynamic blast loads. Following construction of the new Willis Avenue Bridge across the East River between Brooklyn and Manhattan, in-river piers No. 9 and No. 10 from the former bridge were demolished, partially by explosive charges. The blast at Pier 10 was conducted first and though the demolition charge was relatively small, it gave confidence that the sheeting could be designed to resist the blast load. This paper primarily summarizes our analysis and performance of a sheet pile cofferdam at Pier 9 used to withstand the larger blast loads, contain the blast debris, and allow excavation of the pier below the existing river bed mudline. The program NLFlex was used to predict stresses and deformations of the cofferdams under dynamic blast loads, using simplified equations to estimate the underwater blast pressures. Specifically, the analysis focused on the stresses in the struts, waler beam, sheet pile interlocks and connection of the sheeting to the waler beam. Design included allowing plastic deformations and limited rupture of the sheet pile interlocks under the blast loading. Comparisons are made between stresses assessed by the dynamic finite element modeling and empirical relationships used within the industry. The performance of the system after the actual blast is discussed as well as details of the performance of welded vs. bolted connections within the system.

By John Mould, Gordon Chen, Michael Oakland, William McElwee

"This paper will discuss the design analysis of sheet pile cofferdams for static and dynamic blast loads. Following construction of the new Willis Avenue Bridge across the East River between Brooklyn and Manhattan, in-river piers No. 9 and No. 10 from the former bridge were demolished, partially by explosive charges. The blast at Pier 10 was conducted first and though the demolition charge was relatively small, it gave confidence that the sheeting could be designed to resist the blast load. This paper primarily summarizes our analysis and performance of a sheet pile cofferdam at Pier 9 used to withstand the larger blast loads, contain the blast debris, and allow excavation of the pier below the existing river bed mudline. The program NLFlex was used to predict stresses and deformations of the cofferdams under dynamic blast loads, using simplified equations to estimate the underwater blast pressures. Specifically, the analysis focused on the stresses in the struts, waler beam, sheet pile interlocks and connection of the sheeting to the waler beam. Design included allowing plastic deformations and limited rupture of the sheet pile interlocks under the blast loading. Comparisons are made between stresses assessed by the dynamic finite element modeling and empirical relationships used within the industry. The performance of the system after the actual blast is discussed as well as details of the performance of welded vs. bolted connections within the system. IntroductionThe Willis Avenue Bridge is one of the major access ways from the Bronx into Manhattan. The location is shown on Figure 1. The original bridge constructed in 1901 was a swing bridge over the East River. The bridge was in disrepair and outdated with regards to its ability to handle the flow of traffic resulting in numerousaccidents.In 2007, Kiewit Constructors Inc./Weeks Marine, Inc., A Joint Venture was selected to construct a replacement bridge. The $612 million project included construction of a new bridge just to the south of the original bridge. The most notable aspect of the construction was floating and lifting the new 350 ft. long swing span in place as a single piece. However, another significant challenge was using blasting to demolish two of the abandoned piers which were within the East River. The blast would be near existing structures in both Manhattan and Brooklyn and would be within 30 ft. of the new bridge."

Jan 1, 2017

"1.0 DESCRIPTIONThis work consists of furnishing all necessary labor, equipment, and materials to install prefabricated vertical (wick) drains in the ground in accordance with the Plans and as specified herein.2.0 REFERENCED CODES AND STANDARDSASTM D4716-08 Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant HeadASTM D4632-08 Standard Test Method for Grab Breaking Load and Elongation of GeotextilesASTM D4533-11 Standard Test Method for Trapezoid Tearing Strength of GeotextilesASTM D4491-99a Standard Test Methods for Water Permeability of Geotextiles by Permittivity (2009)ASTM D4751-04 Standard Test Method for Determining Apparent Opening Size (A.O.S.) of a GeotextileASTM 6918-09 Standard Test Method for Testing Vertical Strip Drains in the Crimped Condition3.0 QUALIFICATIONSThe Contractor shall have successfully completed a minimum of five wick drain installation projects in similar ground conditions, and installed not less than 5,000,000 linear feet (1,525,000 linear m) of wick drain in the past five years. The Contractor shall have a minimum of five continuous years of wick drain installation experience."

Jan 1, 2014

By Jean Wehbe, Daniel C. Brahana

"The new Mercedes-Benz Stadium (MBS), home of the Atlanta Falcons, is part of a new era of stadium construction in the U.S. These new-age stadiums are larger and have more amenities than their predecessors. Many of the MBS’s features, including its innovative retractable roof, result in extraordinary structural loads. The roof structure is supported by a series of mega columns that bear on eight large caps, six of which are supported by drilled piers. Each of the pier caps contains between 8 and 16 drilled piers that bear in the underlying bedrock. The design pier diameters are 6 and 6.5 ft (1.8 m and 1.9 m). Augercast piles were used to support two of the mega column caps. Drilled piers, augercast piles, aggregate piers and spread footings were used to support the more lightly loaded portions of the structure.The focus of this article is the construction aspects of the drilled pier foundations. Initially, a fairly extensive drilled pier load test program was performed. Load testing included a Statnamic compression test, two Osterberg Cell tests and two lateral tests. Production pier installation included over 3,800 linear ft (1,158.2 m) of earth excavation and over 1,350 linear ft (411.4 m) of hard rock excavation. The piers contain more than 6,600 cu yd (4,587.3 cu m) of concrete and 1,100 tons (998 tonnes) of reinforcing steel. Drilled pier installation took about 4.5 months. ABE Enterprises was the specialty foundation subcontractor and Bauer-Pileco was the equipment provider.Site and Subsurface ConditionsThe project site is in downtown Atlanta and was originally occupied by residential buildings. A portion of the site was later developed as a rail yard, and other areas contained light manufacturing, warehouses and other relatively light structures. For the past 15 to 20 years the site had been used for surface parking.Beneath a surficial layer of manmade fill, soil test borings at the site generally encountered residual soil, partially weathered rock and the parent bedrock. The bedrock at the site is highly variable, both in elevation and in hardness/quality. The depth to rock is reasonably uniform within the western two-thirds of the site at about 20 to 50 ft (6 to 15.2 m), with a few exceptions. In the eastern third of the site, the rock drops off dramatically to the north and east. In one mega column cap, there was almost 80 ft (24.3 m) in elevation difference. In two borings in the cap that were 20 ft (6.1 m) apart, the top of rock varied in elevation by 34 ft (10.3 m)"

Jan 1, 2016

By Jamey Rosen, Georgette Hlepas

Verticality data collected from panel and pile elements of seepage barrier walls describe the shape and position of those elements in three dimensions. These data are used to determine if a barrier wall is constructed as designed and if it meets the owner specifications with respect to tolerance (i.e., if each element is sufficiently close to vertical) and overlap (i.e., do adjacent elements overlap sufficiently to prevent leakage). Contractors use verticality data to confirm that their work matches the design, and owners use verticality data to verify the contractor’s work and confirm that specified criteria were met. Project Information Management Systems (PIMS) technology has been applied to the management, visualization, and analysis of verticality data. This paper will provide examples of how contractors and owners have used a PIMS to compile and synthesize data collected during excavations (e.g., from Cutter Soil Mixer and Hydromill drill rig telemetry), and from measurements of completed excavations (e.g., using the Koden ultrasonic tool), and used those data to model excavation geometry. We will present case studies of using these models to estimate backfill placement volumes, and to evaluate the verticality tolerance and overlap between elements.

Sep 8, 2021

By Moritz Schleeh, Christian Moormann

Temporary working platforms are generally required in order to ensure that heavy construction machinery such as drilling and trench wall units, pile drivers, vehicle and crawler cranes can be set up safely at the site of operation. Considering all possible operating and loading conditions, especially on ground of low shear strength and stiffness, the design and construction of temporary mobile working platforms needs to be considered more as a serious engineering task than as a second order structure of minor relevance. Working platforms reinforced with one or several geosynthetic layers have proven to be especially effective with regard to stability, serviceability and durability but their design requests even more sophisticated approaches. Existing design models are often based on simplified assumptions and do not consider the complex interaction between construction machinery, working platform and subgrade. Non-monotonic loading as well as elastoplastic and time-variant deformation of cohesive subsoil can adversely affect the base layer system and the serviceability and stability of the construction machinery operating on it. In this context, there is a need for improvement of design approaches and their optimisation considering that there are no generally accepted design approaches or technical codes of practice available for the design of temporary working platforms. The present paper deals with the multifaceted and non-trivial interaction effects of working platforms investigated by model tests, field measurements and numerical simulations to develop a design approach that ensures a safe installation and operation of heavy plants on unstable ground.

May 1, 2022

By Pratik Goel, Sumanta Haldar

High-speed rail is an emerging area of interest in India. The Government of India is implementing prestigious bullet train projects in various parts of the country. High-speed rail (HSR) will be operating in India at about 320 kmph at an elevated track on a viaduct for most of the ongoing and upcoming corridors. High-speed projects in India necessitate an indigenous solution for design applications for viaduct design. Pile groups are extensively used in viaducts for high-speed trains, as they can be a settlement reducer and increase the bearing capacity. Post-construction settlement of pile foundation for high-speed railway viaduct is a concern of engineers. Limited attention has been paid to estimating the post-construction settlement. This paper aims to propose a prediction of the cumulative settlement of pile groups due to cyclic train loading. A three-dimensional finite element model (3D-FEM) of the pile group is established in Abaqus CAE. A suitable plastic model is used to simulate the subsoil. The pile group is modelled as an isotropic-elastic element. The study examines the influence of cyclic loading time and train speed on the settlement of the pile group. The analysis is carried out considering various single pile and pile group parameters like S/D, Ep/Es, L/D, Pile cap thickness, etc. and finally, an optimum configuration is suggested.

Sep 1, 2022

By Lori A. Simpson, Linda H. Liang

A high-rise building, consisting of two tower structures occupying the entire site, is in construction in San Francisco. The North Tower will consist of 12 and 35 stories above a one-level basement. The South Tower will consist of 9 and 22 stories over one partially below-grade level of common space; a portion of the South Tower will have a three-level basement. The towers will be supported on mat foundations bearing on native very dense sand in the footprint of the threelevel basement and on ground improved with soil-cement mixed (SCM) panels that extend through loose sand and marsh deposits into very dense sand. Shoring systems for the basement excavations include cantilevered and tiedback soldier-beam-and-lagging systems and SCM cutoff walls. Subsurface conditions include loose fill and Dune Sand and loose and soft marsh deposits overlying very dense sand of the Colma formation. Groundwater is approximately 15 to 22 feet deep; the three-level basement extends below groundwater. The site is on Market Street in San Francisco, with SF Municipal Railway (MUNI) and Bay Area Rapid Transit (BART) tunnels running below Market Street approximately 45 and 36 feet north of the site, respectively. Both tunnels are 16.5 feet in diameter. The top of MUNI and BART tunnels are 25 feet and 63.5 feet below street grade, respectively. BART has stringent requirements regarding construction adjacent to their facilities, including disallowing adding pressure to their tunnel, lowering groundwater by more than two feet, and vibrations from construction activities. Design of the shoring and the foundations within the BART zone of influence were subject to their design requirements. The project was also subject to a peer review, as required by the San Francisco Department of Building Inspection. We used FLAC to evaluate stresses at the BART and MUNI tunnels and on the SCM panels. This paper will present the mitigations needed to address seismic hazards and BART restrictions and to provide adequate foundation support for a tall building with high seismic loads.

Jan 1, 2017

By Lori A. Simpson

A high-rise building, consisting of two tower structures occupying the entire site, is in construction in San Francisco. The North Tower will consist of 12 and 35 stories above a one-level basement. The South Tower will consist of 9 and 22 stories over one partially below-grade level of common space; a portion of the South Tower will have a three-level basement. The towers will be supported on mat foundations bearing on native very dense sand in the footprint of the three-level basement and on ground improved with soil-cement mixed (SCM) panels that extend through loose sand and marsh deposits into very dense sand. Shoring systems for the basement excavations include cantilevered and tied-back soldier-beam-and-lagging systems and SCM cutoff walls. Subsurface conditions include loose fill and Dune Sand and loose and soft marsh deposits overlying very dense sand of the Colma formation. Groundwater is approximately 15 to 22 feet deep; the three-level basement extends below groundwater. The site is on Market Street in San Francisco, with SF Municipal Railway (MUNI) and Bay Area Rapid Transit (BART) tunnels running below Market Street approximately 45 and 36 feet north of the site, respectively. Both tunnels are 16.5 feet in diameter. The top of MUNI and BART tunnels are 25 feet and 63.5 feet below street grade, respectively. BART has stringent requirements regarding construction adjacent to their facilities, including disallowing adding pressure to their tunnel, lowering groundwater by more than two feet, and vibrations from construction activities. Design of the shoring and the foundations within the BART zone of influence were subject to their design requirements. The project was also subject to a peer review, as required by the San Francisco Department of Building Inspection. We used FLAC to evaluate stresses at the BART and MUNI tunnels and on the SCM panels. This paper will present the mitigations needed to address seismic hazards and BART restrictions and to provide adequate foundation support for a tall building with high seismic loads.

By Kevin Baumgartner, Steven Babcock

A landfill in Phoenix, AZ reached capacity and was graded over in the 1970s. The property was subdivided into lots in 2007 to create a business park. However, the challenging site conditions caused by the underlaying landfill put into question the feasibility of typical deep foundation systems. Several different foundation systems were evaluated to support the proposed development. The considered systems were: drilled concrete shaft, driven piles, drilled micropiles and helical piles. Soil stability, landfill decomposition, method of installation, flexibility of design, anticipated material, and equipment costs were considered. A system of helical piles with concrete pile caps and grade beams was selected. To mitigate unknown obstructions, holes were drilled through the landfill debris at pile locations and then backfilled with screened granular material. The helical piles were installed through these backfilled holes and advanced to bear in competent native material below the landfill. This method allowed for minimal disturbance of the landfill materials and provided a strong and adaptable foundation. Additional advantages of helical piles on this site include minimal installation vibration, no grout or concrete in the deep foundation, and capacity verification for each pile via torque correlation. Two load tests were performed to verify the design.

Sep 8, 2021

By Andrew Moran, William H. Walton, Matthew D. Emrick, Mary C. Nodine

"A rapidly growing company in the northern US needed a large auditorium built into a dolomite bedrock hillside. The structure required an 80-foot-deep earth retention system independent of the auditorium foundation and superstructure. Allowable wall movements were limited to less than two inches. A 60-foot-tall permanent shotcreted soil and rock nail wall was designed for excavation support. The soil and rock nail wall utilized both active (post-tensioned) and passive nails, with capacities and installation angles optimized to address varying soil and rock conditions and to support heavy surcharges. The wall was configured with three two-foot-wide benches to facilitate controlled blasting and removal of more than two million cubic yards of soil, limestone and dolomite bedrock, and featured a permanent cast-in-place concrete face and a robust waterproofing and drainage system. A 20-foot-high reinforced concrete retaining wall was required at the top of the soil and rock nail wall to raise grades, resulting in a large surcharge.Design of the soil and rock nail wall was initiated less than three months before the start of construction, requiring expedited geotechnical explorations, analyses, design, and construction that would occur simultaneously. Design changes were made to address the discovery of a weak clay residuum seam at depth running along the base of the excavation, as well as significant changes to the building footprint made after the start of construction. Extensive performance monitoring was conducted during construction to measure vibrations and movements.Introduction and Project BackgroundA fast-growing company in the northern United States had a need for 600,000 square foot, 11,000 seat auditorium as part of its campus expansion. The auditorium was built underground, into a hillside to preserve the views of rolling terrain and farmland beyond. It featured a green roof and rockwork facing that mimicked regional geologic formations. The sixstory building required up to 80 feet of earth retention, including 60 feet of excavation beneath existing grades.As concepts for the project evolved, it became apparent that due to the geologic conditions, space limitations on site and the depth of cut required, a standard counterfort wall system would not be feasible. With groundbreaking for the building three months away, Thornton Tomasetti (structural engineer) engaged GEI Consultants, Inc. (wall design engineer) to design a 1,600-foot-long permanent soil and rock nail wall to support the excavation. The wall design engineer implemented a geotechnical exploration program immediately and began the design process, coordinating closely with Nicholson Construction (specialty"

Jan 1, 2017

By Roberto A. Lopez, Eric Lindquist, Jon Bussiere, Dean Iwasa

"The new 11-story U.S. Federal Courthouse building in downtown Los Angeles demanded a cost effective foundation system capable of attaining a strict total settlement criterion of 0.5 inches (12 mm) under high applied loads. A design-build ground improvement system consisting of 3 ft (0.9 m) and 7 ft (2.1 m) diameter deep soil mix (DSM) columns embedded into the relatively soft Fernando Formation bedrock was selected for the project. The DSM columns support applied stresses of up to 8,800 psf from four large concrete core elements that transfer concentrated building loads to a 3 to 6 ft (0.9 to 1.8 m) thick reinforced concrete mat. The soil mixing ground improvement solution provided flexibility by allowing installation of the DSM columns around existing belled caissons left in place from prior structures, and by allowing repositioning of some of the DSM columns to avoid other existing obstructions in the fill. DSM spoils were used to construct a 2 ft (0.6 m) thick load transfer platform on top of the DSM columns. Quality control measures included utilizing equipment outfitted with automated data acquisition systems, performing three full scale load tests, performing daily wet-mix sampling and compression testing, performing full-depth coring and unconfined compression testing on core samples, and using a borehole acoustic televiewer to evaluate the uniformity of the DSM columns where core recovery was problematic. The results of subsurface investigation and the load tests were used to develop 3-dimensional finite differences models for evaluating stress distribution and deformation of the foundation system.INTRODUCTIONThe new U.S. Federal Courthouse building is currently under construction in downtown Los Angeles, California. The new courthouse will be 11 stories tall with one partial below-grade B1 basement level. The building will have four structural core elements that extend from the main building foundation at the B1 level to the top of the structure. The majority of the building loads will be transferred through the structural core elements to a new 3 to 6 ft (0.9 to 1.8 m) thick reinforced concrete mat beneath the central portion of the structure. The foundation pressures beneath each of the core element locations will be approximately 6,200 to 8,800 psf (300 to 420 kPa) with lower foundation pressures at locations farther away from the central core area."

Jan 1, 2015

By Dennis Nottingham

"Increased interest in seismic soil liquefaction and preventative soil stabilization sets the stage for improved deep compaction methods using pile driving techniques. In 1971, L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100-foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers’ experiments, observations and measurements, led to an “H” pile probe design which has produced measured soil density improvements up to 250% using SPT “N60” values as a measure. Case histories of two projects involving extensive SPT soil sampling comparative measurements will be discussed along with findings that led to the compaction success. Applications to numerous modern “Open Cell” bulkhead projects will be presented and discussed.INTRODUCTIONNecessity often is the basis for innovation and such was the case for needed cost-effective deep soil fill compaction in Open Cell bulkheads where granular fill below water levels was often placed.Open Cell bulkheads were developed by PND Incorporated starting in 1980, for the express purpose of meeting client demands for an economical, easily constructed, extremely strong structure. Earth-filled structures historically have had a long history of problems with stability, scour and settlement.Open Cells are flexible steel sheet pile membranes supported by soil contact with embedded tail anchor walls.This concept creates an integral reinforced soil system. The result is a structure that can withstand large settlement and support a variety of very large loads. In effect, viewed from above the structure becomes a series of U-shaped horizontal membranes that require no toe embedment for stability. The Open Cell bulkhead is constructed of only three components: flat sheet piles, fabricated connector wyes and anchor piles. Compared to alternative structures, several cost savings are realized from this land based construction such as, reduced sheet pile area, greater construction tolerance, minimal pile penetration, and simplified backfilling procedures. In seismic regions or weak soils, the tail walls can be extended as required to guarantee fill mass stability."

Jan 1, 2005

By M. Kitazume, H. Imai

The deep mixing method was developed in Japan and put into practice in the middle of 1970s. Since then, the wet and dry type methods have been applied for various improvement purposes in Japan. One stork of mixing tool produces a column shape of stabilized soil in a ground. By the series of productions, arbitrary shape of improved ground can be constructed by overlapping each columns. It is specified to complete the overlapping within 24 hours in order to ensure the tight connection of the columns. However, it can not be completed within the specific time in some cases due to bad weather or machine trouble, which causes a cold joint in the improved ground. In this study, the influence of the cold joint to the behavior of the block type improved ground is examined by a series of centrifuging model tests and FEM analyses. It is found that the ground behavior is influenced by the position of the cold joint, where the cold joint at the sea side shows a little influence to the behavior but one at the port side causes large decrease in the stability of the improved ground.

Sep 8, 2021

By Dan Brown

Improvements in construction equipment and techniques in recent years have made possible the use of drilled shaft foundations in diameters and lengths not previously considered practical or feasible. Many highway bridge and other structures are now routinely founded on drilled shafts which -are 8 to 12 feet in diameter and extending over 200 feet in depth below grade. There are unique challenges associated with constructing such large and deep cast-In-place foundations and engineers should be aware of the special needs associated with site investigation, construction specifications, material requirements, and quality assurance. This paper outlines a number of special considerations for these foundations, along with strategies that may be employed to improve the reliability and quality of large drilled shaft foundations.

May 11, 2007

By Matthias Pulsfort, Hanna Nissen, Markus Herten

An insufficient integrity of cast in-situ bored piles can lead to a reduction of the load bearing capacity and may require cost intensive repairs. Reasons for an insufficient pile integrity are linked to the construction process, mainly to poor concrete quality leading to bleeding and segregation of the fresh concrete. Moreover, the entrapment of soil and an insufficient concrete cover can pose a problem. Knowledge about the time-dependent development of the fresh concrete pressure during the construction process of bored piles is needed for a better understanding of the underlying processes causing these defects. Therefore, pressure measurements were carried out on different construction sites with pressure cells being installed at different depths along the reinforcement cage. The measurements revealed the maximum pressure acting on the surrounding soil. The achievement is a better understanding of the effects of the concrete placement specifically and the construction process in general on the surrounding soil to reduce the risk of pile imperfections.

Sep 8, 2021

By Ryan Sullivan, Lisa Smiley, Jewels Stover

The Westerly Storage Tunnel (WST) Project is part of Project Clean lake, the North East Ohio Regional Sewer Dist years. When completed in 2020, WST will be nearly 2 miles of 25-ft diameter tunnel 200-250 ft below ground. The storage tunnel will manage higher flow volumes, keeping stormwater out of the combined sewer system reducing overflow occurrences. Three deep shafts provide access to the tunnel at the tunnel boring machine (TBM) launch and retrieval sites, as well as a vent shaft. Support of excavation for the access shafts was constructed utilizing unreinforced concrete diaphragm walls. This innovative, value-engineered alternate design significantly reduced risks associated with conventional secant piles combined with a rib and liner plate system. Implementation of the diaphragm wall technology resulted in a water tight, continuous shaft keyed into rock. This case study examines the design, methodology, and installation challenges unique to each shaft, as well as the benefits of the final product to the overall project.

By Joseph T. Coe, Alireza Kordjazi, Michael Afanasiev

Cross-hole sonic logging (CSL) is a common quality assurance measure for the evaluation of the structural integrity of drilled shafts. The results of CSL can be supplemented by a set of tomographic images generated by cross-hole tomography (CT). Although the same access tubes, sources and receivers are used in both methods, CT has the advantage of providing a higher quality image of the possible anomalies in drilled shafts. Nevertheless, it has been reported in literature that the CSL and CT miss anomalies with sizes of smaller than 10 percent of the cross sectional area of the drilled shaft. This implies poor resolution despite the high-frequency of the stress waves utilized in these methods. This issue with resolution can be at least partially attributable to the fact that CT relies entirely on the inversion of the first time of arrival and ignores the information embedded in the rest of the recorded traces. This study examines the application of full waveform inversion (FWI) to generate a higher resolution image of the possible defects in drilled shafts from the same data used for cross-hole tomography. FWI is a wave-field method that aims to directly match the recorded traces with traces obtained from a numerical model of the domain. This has the benefit of avoiding the selection of the first time of arrival, along with increasing the resolution of the final image due to extracting more information out of the traces. Through a series of numerical simulations, synthetic traces were generated from a drilled shaft with defects of known mechanical properties, dimensions, and location. These traces were then inverted to evaluate the performance of FWI for structural integrity testing of the drilled shafts. INTRODUCTION The presence of construction defects can compromise the structural integrity of drilled shafts and negatively affect their performance (O’Neil 1991; Sarhan et al. 2002; O’Neil et al. 2003; Poulos 2005). Several non- destructive testing (NDT) methods exist that are currently used for the evaluation of the structural integrity of drilled shafts. Cross-hole sonic logging (CSL), cross-hole sonic tomography (CT), and thermal integrity profiling (TIP) are well-established and documented in the industry and practical manuals (Brown et al. 2010). NDT methods prevent the need for coring and excavation and are relatively fast and cost effective. Successful implementation of these techniques has also been reported in the literature (Branagan et al. 2000; Iskander et al. 2001; Mullin 2010; Johnson 2016).

Jan 1, 2019

By Waddah Akili

At an offshore site along the Red Sea coast of Saudi Arabia, marine structures were supported on tubular steel piles driven into coral and coral contaminated sands and silts. Surprises and disappointments faced during the installation of the piled foundation were, to a large measure, due to inappropriate design methodology and absence of proper soil information. The paper describes the design evolution process, highlights the static pile test program conducted to verify design parameters, and amplifies the need to prepare for worst possible scenario when coral deposits are encountered. Despite corrections made to the design, based on site-specific insitu parameters (skin friction, end bearing) perceived from load tests conducted on site; the final design adopted overestimated capacities in over 50 percent of total piles driven. The paper describes the changes introduced to the design during the execution of the project, highlights the pile test program conducted to verify the design, and compares pile design penetration with actual penetration depth. The unpredictable and erratic pile behavior observed, ascertains the need for more appropriate pile design and installation guidelines for driven piles in coral and coral contaminated formations.