Search Documents

Jan 1, 1996

By Tim Chapman

This general report considers what promoters of deep basement projects want from their teams and whether they get it often enough. Most large projects are based on complex financial models where the funding is related to a future income stream. Project delays and cost over-runs can critically affect the financial model. Too often, delays and cost over-runs originate in the substructure and foundations. We must take positive steps to improve our industry's reputation for reliability.

Jan 1, 2006

By Emad W. Shublaq

Contractual site plans are implemented for executing pile foundations (5 x 5) at segmental concrete bridge. Project schedule demands have forced the contractor to find out the most economical procedure in achieving the goal. This paper presents a site management technique which is applied by the Contractor. This was found to be fruitful and as much as 60% saving was gained.

Jan 1, 1992

By Matthias Baeßler, Markus Herten, Ernst Niederleithinger, Steven Georgi

"Abstract: BAW and BAM have performed a large scale comparison and calibration test on static and dynamic load capacity evaluation of bored piles in glacial sandy soil. The test was performed using eight piles at the BAM test site for technical safety at Horstwalde 50 km south of Berlin. The test area has been prepared and investigated in great detail using boreholes, cone penetration tests, pore pressure sensors and geophysical methods to assure controlled conditions for all piles and tests. The piles (10 m length, 0.9 m diameter) are mainly friction piles (low toe resistance) and have been checked by integrity testing. Five piles have been tested by five contractors using the dynamic method in a blind experiment, the other ones piles by static load and/or later on by the dynamic method. Some piles have been equipped with additional fibre optic instrumentation which proved to be robust and helpful in interpreting the results of static, dynamic and integrity tests. We have experienced a deviation of the dynamic load test results gathered in the blind experiment from the static values of up to 20% in most cases, sometimes even up to 30%. This can be related to the known soil inhomogeneities, interpretation and modelling in CAPWAP and method inherent uncertainties. In cases where the static values were known by the testers for calibration, the deviations were significantly smaller. It has to be taken into account, that the two static load tests showed different results as well. Due to the low toe resistance, use of a big drop weight (11 tons) and large drop heights most piles suffered from cracking, which was clearly seen in follow up integrity tests and confirmed by excavation. The piles are available for further research.IntroductionBored piles are used in many construction projects of the German waterways authorities, e. g. bridges, piers or locks. Their load carrying capacity varies with pile type and geometry as well as soil type, parameters and structure and is thus not easy to calculate in advance. Dynamic pile testing as a cost effective addition or replacement for expensive load tests is accepted in many places (Beim and Likins 2008) but still doubted in others. Inspired by the international prediction event for piles in residual soil carried out in the frame of ISC’2 (Viana de Fonseca and Santos 2008), governmental research institutes have designed an experiment in a geological setting typical for glacial and post-glacial areas in northern Germany. Some results have already been presented by Niederleithinger et al. (2012), Herten et al. (2013) and Baeßler et al. (2013). It was intended to perform a blind test for load capacity estimation using dynamic pile testing on six drilled shafts involving five test crews. Two other piles would have to be tested thereafter using static and dynamic methods."

Jan 1, 2014

By Helen S. W. Chow

The use of piled raft foundations for tall buildings has been increasing in this decade as it is an economical alternative to conventional piled foundations. Piled rafts are composite structures comprised of the piles, raft and soil and so soil-structure interaction is important in computing the behaviour of the foundation. In this paper, the behaviour of piled rafts subjected to non-uniform loadings will be examined where the raft is supported by piles of different lengths. Finite layer techniques are used for the analysis of the horizontally layered soils and finite element techniques are used for the analysis of the raft and piles. This method accounts for the soil-structure interaction and the lateral resistance of the soil on the piles and raft. Results provided from the present method are compared with the results of a full 3D finite element analysis.

Jan 1, 2006

By H. Boghosian

This paper presents the design and construction of a deep basement in a steeply sloping site in glacial till in Glasgow city centre. Existing foundations, adjacent structures and services, in tandem with asymmetric loading, presented particular challenges in the planning, execution and design of the project. The construction methods and temporary works, analysis by the Finite Element method and monitoring carried out are all described.

Jan 1, 2006

By Raffaella Granata, Wesley Schmutzler, Matteo Bertoni

"The Lower Wood River Levee system, at the confluence of the Wood River Creek and the Mississippi River, in East Alton, Illinois, has been plagued with underground seepage and, in 2010, remediation was deemed necessary by the Southwestern Illinois Flood Prevention District Council and the United States Army Corp of Engineers (USACE). The experts enlisted by the council produced a design that provided for constructing a cutoff wall approximately 2,000 feet long and up to 140 feet deep, through alluvial and outwash soils, and embedded in bedrock. This paper will describe the challenges faced by the Quality Control (QC) and Quality Assurance (QA) teams due to the complex nature of the project in conjunction with an extremely thorough QC/QA program.INTRODUCTIONThe “American Bottom” is an area of 453 km2 (175 square miles) in Southwestern Illinois, extending from Alton south to the Kaskaskia River, which is home to 156,000 people. In the 1940s and 1950s the U.S. Army Corp of Engineers (USACE) designed and built a 120 kilometer (74 mile) long levee system to protect the area from a 500-year flood event on the Mississippi River, which flows through it. The levee system has been plagued by under-seepage for several years. The phenomenon has worsened to varying degrees, depending on location, to the point that remediation was needed.The Southwestern Illinois Flood Prevention District Council (SIFPDC), to obtain Federal Emergency Management accreditation, in June 2010 commissioned a team lead by Amec Foster Wheeler for the design and management of the required levee improvements. The team presented in 2011 the project’s first set of drawings showing proposed design features throughout the levee system. The project was subdivided in four areas, based on the controlling levee districts, one of which, the Wood River Drainage and Levee District, was split into three subdivisions: Upper Wood River, East-West Forks of Wood River, and Lower Wood River.The project included the installation of a cutoff wall at the confluence of the Wood River and the Mississippi River in East Alton, IL (Fig. 1). The Engineer of Record (Amec Foster Wheeler) considered the cutoff wall as the only viable solution to stop the severe under-seepage that was undermining the integrity of the Lower Wood River Levee. The Lower Cutoff Wall (LCW) project is the subject of this paper."

Jan 1, 2017

By Dario Libano

"The Line 5 Extension, in Sao Paulo, Brazil, is currently the most important investment in public transportation by Sao Paulo’s state government. It will connect the south part of the city to the city center, crossing through four other major Metro lines and stations; all currently in operation. The total extension of the line is 11 km (6.8 mi), and includes a new parking yard for the trains and 11 new stations. The Brooklin Station, one of the new stations due to be open and operating in 2016, has a unique geometry of five secant shafts.The original design included constructing five secant shafts stabilized by two plastic slurry walls using conventional grab technology. One slurry wall, along the Santo Amaro Avenue, was to contain the contamination plumes, and another was for temporary support to enable the excavation of the shafts. The final retaining wall design was changed to a concrete structural diaphragm wall that reduced the construction time of the shafts by half, allowing the contractor to meet the construction schedule. This solution also avoided dewatering effects in a geological region characterized by Quaternary sediments and environmental contamination plumes. It was the first time that a hydromill was used in such a situation in Brazil. The hydromill, by overcutting the panels, increased the quality of the joints, and decreased the probability of having seepage into the shafts. The hydromill also created a seepage barrier and avoided movement of the contaminated plumes.The GeologyLocal geology is composed of a superficial Quaternary soil, basically soft organic clays and sands and gravels. From the depth of 8 m (26 ft) until 18 m (59 ft), geology is composed by tertiary medium compact sand with thin silt-clay layers. From 18 m (59 ft) down, there are alternations between compact silt-sands layers with very hard clays layers. Each is approximately 5 to 10 m (16.4 ft to 33 ft) thick.The Initial Basic DesignThe original basic design of the Brooklin Station was to be constructed from five 40 m (131 ft) diameter intersecting circular shafts, all in a line along the axis of the Metro tunnel, in 555 days. In the excavation sequence, the odd shafts were first excavated, waterproofed and had part of their inside cast-in-place structure built before the even shafts were excavated. During the excavation of the even shafts, part of the odd shaft’s support was demolished and connected with the even support. A 0.8 m (2.6 ft) thick plastic slurry wall, acting together with the wire mesh reinforced shotcrete support, ensured the excavation stability around the five shafts."

Jan 1, 2014

By Frederic Masse

With widespread acceptance in the market place, many engineers are choosing ground improvement techniques to provide suitable foundation subgrade at sites that would have traditionally required deep foundations. This paper discusses the Controlled Modulus Columns (CMC) ground improvement technique and some case histories highlighting the use of this technique for retail development sites. CMC are a sustainable and cost-effective ground improvement technology that transmit load from the foundation to a lower bearing stratum through a composite CMC/soil matrix. The CMC installation is also an attractive option from an environmental perspective because it utilizes reverse flight augers, which displace the soil laterally. This installation technique achieves two goals: it densifies the soil around the CMC, which improves load transfer into the element and avoids spoil and its disposal. Through the introduction of two cases histories, we will present the key benefits of the CMC technology. Each case history will clearly illustrate how a CMC solution can reduce the overall cost of a project when compared to a more traditional type of deep foundations. They will also show how the use of CMCs has benefits that relate to the overall sustainability of the project. While CMCs are an attractive financial and sustainable option, they have also demonstrated that the performance of the system is comparable to that of deep pile foundations. Because CMCs are a relatively new technology many potential users are not aware of its benefits. While we discuss the use of CMCs to support buildings in this paper, CMCs also have been used for a variety of other applications including foundations for tanks, mechanically stabilized earth (MSE) walls, and embankments

Jan 1, 2011

Jan 1, 2001

By Felix Cheng

Extensions to the Convention Centre in Adelaide, South Australia consisted in part of construction over the existing railway system comprising nine rail lines and passenger platforms. Vibro-pile (Aust) won the design and construct tender with a solution comprising over 500 cast insitu concrete piles. The pile types were 500 to 900mm diameter non-displacement CFA piles and 400mm diameter displacement V-piles. The V-pile is a cast insitu screw pile developed by Vibropile (Aust) Pty Ltd. Both pile types were installed with minimal noise and vibration required for the project, while the displacement V-pile had the advantage over the CFA pile by developing the same pile capacity but with a smaller diameter and with minimal spoil. The latter was important in alleviating spoil removal problems near the railway tracks and disposal of potentially contaminated spoil. The results of dynamic compression load testing and static lateral load testing indicated that the performance of a 400 mm V-pile was equivalent to a 500 mm CFA for this site. The lateral load testing indicated that the surficial soils have a major influence on the load-deflection response, but despite the site containing up to 4 m of filled ground, the piles were found to carry the required lateral loads satisfactorily.

Jan 1, 2002

Jan 1, 1988

By T. Ruben

Micropiles have been used for the last forty years to strengthen building foundations. This article gives information about the technology and capacity of micropiles.

Jan 1, 2000

By Derrick Dasenbrock

Two DFI committees independently organized two complimentary panel sessions for the recent American Society of Civil Engineers' (ASCE) Geo- Risk 2023 "Advances in Theory and Innovation in Practice" Conference in Arlington, Virginia, July 23-26. The Geo- Institute (GI) specialty conference welcomed more than 200 professionals and students interested in risk from around the world to the Washington, D.C., area for three full days of plenary keynote lectures, papers and no-paper sessions. The GI Risk Assessment and Management Technical Committee organized the event, which is the third in a series planned on a 6-year cycle. The previous two events were in 2011 in Atlanta and 2017 in Denver.

Sep 1, 2023

By A. J. Partos

One Liberty Place, at 315 m is the tallest building in Philadelphia, PA USA. It is supported on drilled piers socketed in heterogeneous rock. 3832 kN/m2 end bearing and 383 to 766 kN/m2 shaft resistances were selected. Design load distribution was 40% on the base and 60% by shaft resistance. The maximum compression on the corner core columns is supported by clusters of 3 drilled piers. In order to confirm load distributions along shaft and at the base, Drilled Pier G-10 supporting T13-A type outrigger column was instrumented. This column supports 53,849 kN compressive load which includes 13,440 kN windload. This paper reveals details about the process to select the final design for One Liberty Place together with pertinent Information about site geology, foundation construction, quality control, and methods of steel erection. It also presents detailed Information on the type of Instruments, their calibrations, field fabrication, and installation in the shaft of Pier G-10. Readings of concrete temperatures, computed loads, and load distributions are presented for a period from October 1985 through May 1988. The building was completed in 1987.

Jan 1, 1989

By Kenneth Gavin

Design practice for piles installed in Irish glacial till has developed in an ad-hoc manner, based on the results of un-instrumented load tests. This had led to designers using similar design parameters for both CFA and displacement piles. To address the concerns of industry a series of instrumented pile tests were performed by two Irish Universities. These tests summarized herein, revealed that CFA piles develop higher shaft resistance than piles driven in glacial till. However, they exhibit low base stiffness and the end bearing resistance that can be mobilized at acceptable pile settlement is low. The use of simple non-linear elastic design approaches to predict the load-displacement response is considered. The methods are used to predict the capacity of two large diameter CFA piles installed in glacial till. While the predictions were reasonably accurate at predicting the initial load-displacement of the piles, significant creep settlement developed at higher load levels. The cause of the creep settlement was investigated through the use of plate load tests and the consequences for pile design are discussed.

Jan 1, 2009

By Brock Wallis, Steve Davidow

The following text will present the concept of rock socketed drilled shafts used to support electrical substation structures, and discuss the cost and schedule risks that traditional design responses to unforeseen shallow rock can pose to a project. Design considerations will be detailed, including rock characterization, shear strength of drilled shafts, and modeling lateral resistance of the shaft and surrounding rock. The specific case of drilled shafts installed for heavily loaded structures at the Moxie Freedom Substation will provide an example of how close collaboration between the engineer and contractor to refine designs based on site-specific feedback can provide tangible benefits to the project. In this example, value engineered designs resulted in an approximate 40% reduction in shaft/concrete volume and a 60% reduction in total rock socket depth. PROJECT OVERVIEW The Moxie Freedom Project included the construction of a new 500 kV switchyard in Berwick, Pennsylvania. The foundation contractor was selected to install both small and large diameter drilled shaft foundations to support the structures within the switchyard. The small diameter shafts were utilized to support transformers, switches, bus supports and a static mast, while the large diameter shafts were used to support one 180-foot monopole and six H-Frame structures. CHALLENGES: ROCK SOCKETED DRILLED SHAFTS Available geotechnical data at the time of bid included limited borings and seismic refraction. The borings were not located at every structure, and the contractor and design engineer were left to interpret desktop studies and geophysics to determine the probable site-specific conditions at each foundation. The data suggested substantial variability in the quality and depth to bedrock across the project area, indicating significant risk of deep embedment into bedrock at all seven large diameter shaft locations. Rock socketed drilled shafts pose unique challenges for both designers and contractors, and the topic has become a focus of national foundation organizations. Traditional design models result in deeper and/or larger diameter shafts where rock is encountered. In the case where site-specific geotechnical conditions are not clearly understood and rock is encountered at shallow depths, this can lead to significant additional rock drilling, impacting overall project cost and schedule. Rock drilling can result in more than ten times the cost of soil drilling and can easily take in excess of ten times longer to excavate.

Jan 1, 2018

By Kazuyuki Matsuzawa

A series of plate loading tests were carried out on a loam ground in order to investigate the influences of the plate size and the loading rate on the observed load-settlement relations. Two circular plates having diameters of 0.3 m and 1.0 m were used. Three types of loading methods were employed; 1) static cyclic maintained load test, 2) static continuous load test, and 3) rapid (dynamic) plate load test. An interpretation method called non-linear damping method was used to estimate a static load-settlement relation from the rapid plate load test signals. The derived static load-settlement relations match well with the measured results from the static load tests.

Jan 1, 2006

By Ramon Varghese, A. Boominathan, Subhadeep Banerjee

Pile raft foundation system has been accepted as an economic foundation design for high rises and heavily loaded structures. Seismic response analysis of PR foundation systems involves complex pile-soil-pile interaction as well as raft-soil-pile interactions, for which simplified methods have limitations. Kinematic rocking of a pile group is known to be influenced significantly by the pile configuration. The presence of an embedded pile cap, or a raft, as in the case of a piled raft can further alter the dynamic characteristics of a pile group-soil system. In the present study, frequency dependent kinematic response factors are evaluated for piled raft foundation, using the substructuring approach based ACS SASSI program. Performance of the numerical analysis methodology is first evaluated with results from analytical and experimental studies reported in literature. The effect of pile layout on kinematic response is then studied for a piled raft in clay system based on a centrifuge shaking table test reported in literature. Kinematic response factors and horizontal impedances were determined for varying pile spacing ratios. The influence of raft has been found to increase kinematic translation by up to three times in the piled raft in clay system. Pile configuration is found to play a significant role in kinematic rocking of piled rafts. The presence of raft is observed to significantly reduce dynamic rotational stiffness coefficient in the dimensionless frequency range of 0.23 to 0.6, and increase damping coefficient after a dimensionless frequency of 0.4, for all pile configurations studied. The effect of an embedded raft is hence an important consideration while evaluating foundation input motion as well as impedances of piled raft foundations. INTRODUCTION The Piled raft foundation (PR), is a composite foundation system that facilitates load sharing between pile and raft. It is an economic foundation option for high rises and heavily loaded structures. Soil structure interaction (SSI) in PR system involves raft-soil-pile, and pile-soil-pile interactions which needs to be considered in static or dynamic SSI analysis. The effect of pile can have substantial influence on foundation input motion, for seismic analysis (Di Laora et al. 2017). Piles are observed to depress a wide spectrum of the seismic excitation (Fan et al., 1991, Di Laora & de Sanctis, 2013). Although kinematic response of pile groups have been extensively studied in the past, the influence of the presence of raft on kinematic response characteristics of pile groups has not received much attention.

Jan 1, 2018

By Eiji Kojima

In this research, dynamic and static load tests were performed on permanent foundation piles which had a pile length of 30 m, 800 mm in outer diameter and 15 mm in wall thickness. In this site the dynamic horizontal load test on a smaller test pile, 12 m in length, 500 mm in outer diameter and 12 mm in wall thickness, was also carried out. The static horizontal load versus horizontal displacement derived from the dynamic load test conformed well to that measured in the conventional static horizontal load test of the pile with 800 mm diameter. Then an attempt was made to predict the horizontal load displacement of the pile with 800 mm diameter based on the results of the dynamic horizontal load test of the pile with smaller diameter of 500 mm.

Jan 1, 2006