Search Documents

By Yvone Franco Crosato

The dense population of Hong Kong requires the construction of tall buildings in reclaimed areas or perched on the slopes of the many hills. The large loads to be supported are carried by deep foundations. Many of those are bored piles, to rock, of diameters up to the 3.0 m. of today.

Jan 1, 2000

By S. T. Kok

This paper presents a case study in West Malaysia for passive piles failure in very soft marine clay in open excavation. In this particular case, the thickness of the very soft marine clay ranges from 5 m to 7 m (16 ft to 23 ft) from the ground surface. Preliminary site investigation reported SPT ?N? value of zero for the very soft marine clay. The design was based on a deep foundation utilizing driven piles to support the superstructure. During pile cap construction, the piles were subjected to uncontrolled open excavation, inducing bending moment in the piles, resulting in some cracked and broken piles. Analyses were carried out using an existing three-dimensional finite element code with a non-linear soil model to predict the response of these piles during excavation. Finally, the predictions of pile responses during excavation were compared satisfactorily with the observed results.

Jan 1, 2009

By Seth L. Pearlman

A major excavation support case history for the Eastern approach to the Third Harbor Tunnel (THT) in Boston, MA is described, which uses an anchored Soil Mixed Wall (SMW). Both general and project specific information is provided regarding the design and construction of SMW walls. In addition, conclusions are presented that discuss the suitability of this particular application and other possible variations.

Jan 1, 1993

By L. C. Reese

? Good construction and inspection presumed. ? Capacity-computation factors are independent of construction method. ? To account for variable or uncertain site conditions, anticipated construction problems, and/or minimal inspection, increase factor of safety. ? Conduct load tests and/or develop easily implemented design alternates (e.g., straight shaft in case bell can't be formed) to reduce factor of safety.

Jan 1, 1988

A technical exhibition was held in conjunction with the 4th DFI International Conference on Piling and Deep Foundations, Stresa. The exhibition was located in the ground floor of the Conference Hall. It was open from 15.30 on Monday April 8 till 16.30 Thursday April 11, 1991. The following is an alphabetical list of firms who took part. 1) A.P. VAN DEN BERG MACHINENFABRIEK B.V. P.O. BOX 68 8440 AB HEERENVEEN The Netherlands Tel: +31 5130 31355 Fax: +31 5130 31212 Stand Executive: A. Duyfjies

Jan 1, 1994

By Arash Maghsoudloo, Asli Can

"Abstract This paper presents a ground improvement implementation case under a raft foundation of a local hospital. The selected ground improvement method is Wet Soil Mixing (WSM) technique. Soil mixing is increasingly applied to environmental applications and ground stabilization in geotechnical projects. In this technique, weak soil is mixed with cementitious slurry to improve the characteristics of the soil. The investigated case is one of the pioneering WSM ground improvement technique implementation cases in Turkey. The soil profile is mainly consisted of low plasticity clay. The effect of ground improvement is verified by a series of laboratory tests and four in-situ pile loading tests. The results of in-situ pile load tests on constructed soilcrete columns showed an acceptable factor of safety for the bearing capacity of the WSM columns. Measured bearing capacities in all four tested columns were nearly 20% higher than calculated values. In addition, a set of samples are obtained from the constructed columns and unconfined compression tests have been conducted. The laboratory test results indicate that the selected cementitious slurry has a sufficient efficiency to form the stabilizing columns.IntroductionIn the construction industry, stabilization of the soft ground by lime or cement stabilization is a widely used technique. In ground improvement systems deep mixing method (DMM) results in the same stabilization in deep portions of the soft soil profile by mixing cementitious slurry by means of mechanical augers. The pioneering cases of modern deep mixing application can be traced back to the year 1970 that was used for the stabilization of marine soils below the water level for the construction of harbor structures (Terashi et al., 1979). Nowadays, DMM is shown to be a proper and efficient method for the foundation of the structures and embankments on land. Some recent studies also reported that reasonable settlement reduction range in the stabilized soils under the foundation of structures (Archeewa et al., 2011). In addition to reduction of the structural settlement under service loads, deep mixing methods are also utilized when there is a concern with contaminated soil and groundwater or groundwater control (Andromalos and Bahner, 2003).Although, the DMM is shown to be a successful method in numerous studies for improvement of a wide range of soil types such as organics, fine-grained, and coarse grained material, it has some limitations (Archeewa et al. 2011, Jameson et al. 2010, Jelisic and Leppanen 2004, Lambrechts and Roy 1997, Meyersohn 2007, Miki and Nozu 2004, Olsson et al. 2008, O’Rourke and McGinn 2004, Stewart et al. 2004, Yang et al. 2011). High soil density and stiffness could damage deep mixing rigs. Engineering properties of the soilcrete columns changes based on the soil type, water content and other factors such as organic content of the available soil profile, so properties of the generated soilcrete should be verified by a set of rigorous testing procedures (Puppala et al. 2004).Based on the general classifications presented in the ground improvement literature, deep soil mixing method is divided into two main types of dry or wet mixing methods. In the dry and mixing methods compressed air and water are utilized as the binder transporter medium respectively (Moseley and Krisch, 2004). In addition, DMM methods can be categorized based on the employed mixing methods during the construction. In this study, the main aim is to present and elaborate on the selected method is known as Wet Speed Soil Mixing (WSSM)."

Jan 1, 2014

By W. D. Guo

With an experimental apparatus developed recently, model tests on piles were conducted in sand subjected to triangular soil movement profiles. Four instrumented piles tests are reported, which show the pile behavior predominantly determined by soil sliding depth. Axial load can create additional bending moment and pile deflection, which also make mode of pile-soil interaction change with sliding depth. Limiting resistance was found 1.5~3 times higher than currently used for laterally loaded piles in sand.

Jan 1, 2006

By Nien-Yin Chang

The contemporary seismic response analysis of structures using a finite element analysis code requires six elastic spring constants to address the six degrees of freedom ground/foundation contribution to the response of a structure to earthquake shaking. However, the ground response is nothing but linear. Thus, it is critical to address the effect of the nonlinear ground response to the performance of structures under strong earthquakes. This study specifically addresses the effect of pile foundation on building vibration using finite element analyses. The effect of single pile was first investigated and the load was applied at the pile head using the single-degree-of-freedom load at a time, including three translational loads in the x, y and z directions and three moment loads about the three respective axes. In this study, the coupling effects between two or more different loads were not investigated. A load is increased monotonically to investigate the nonlinear behavior of pile under various loads. The Mohr-Coulomb model was used to represent concrete. To explore the effect of soil models on the nonlinear spring functions, the following constitutive models of soils were used: linear elastic, Mohr-Coulomb model, Cap model, modified Cam-Clay model, and Duncan-Chang hyperbolic model.

Jan 1, 2007

By Mary Ellen Bruce Large, Antonio Marinucci, Silas C. Nichols

Tip post-grouting of bored pile (drilled shaft) foundations refers to a method where cementitious grout is injected beneath the tip of a shaft to improve the overall performance of the constructed foundation. This technique, when performed satisfactorily and in the appropriate ground conditions, enhances axial load-displacement performance by improving the mobilization of pile’s resistance. Potential benefits associated with tip post-grouting include reduced settlement under loading, better alignment of load transfer curves, and improved ground beneath the base of the bored pile. However, to be able to realize the benefits attributed to this method, the design, construction, of both the bored pile and the post-grouting system must meet a minimum level for quality assurance. The various factors affecting the successful installation and performance of a bored pile (e.g., workmanship, base cleanliness, borehole integrity, and concrete placement) have been discussed by numerous practitioners and researchers in the available technical literature. For a conventional (i.e., ungrouted) bored pile, acceptance is based on a combination of visual inspection, material testing, and the results of integrity and/or performance testing of the constructed pile. A properly executed tip post-grouting program can be a relatively comprehensive and complex process, which is typically evaluated throughout the construction process based on the results of prior projects and/or on test pile(s) at the particular site. For tip post- grouting programs, verification procedures and acceptance criteria should be established during and incorporated into the design process to ensure design intent and objectives are achieved. Project specifications should be produced to ensure performance requirements are achieved. This paper will present and discuss factors affecting the successful execution of tip post-grouting, including grouting criteria, instrumentation, reliability and uncertainty with the method and outcome, and verification and acceptance. INTRODUCTION Constructing bored piles (drilled shafts) is increasingly more challenging given the lack of ideal site locations, tight project site confines, difficult or restricted access, greater demands on drilling equipment, and close proximity to adjacent structures. To evaluate the feasibility of bored piles as an appropriate foundation system, a myriad of factors is evaluated during design, including site conditions and constraints, budgeting and scheduling, reliability and risk exposure, presence of and depth to adequate load bearing soils/rock, and the magnitude of the imposed loading. Moreover, updated design codes increased load demand per element, and improved material strengths have led to more complex foundation designs, larger foundation elements, and significant increases in load magnitude. Monopile (monoshaft) foundations have been utilized where one large bored pile is used in lieu of a group of piles connected via a pile cap. In addition, to accommodate the design criteria, site conditions, and imposed loading, the geometry of the bored piles being designed and installed have been as large as 13 feet (4 m) or greater in diameter and to depths in excess of 260 feet (80 m).

Jan 1, 2018

By A. Eslami

In recent development of piled raft design, the contribution of both raft and piles to tolerate the loads is taken into account, depending on the stiffness and contributions of involved elements i.e.; piles, raft and surrounding soil. The piles are usually required not to ensure the overall stability of the foundation but to act as settlement reducers. One alternative method of foundation design is therefore to introduce piles purely as a means of improving or enhancing the stiffness of the base soil by structurally disconnecting the piles from the raft. In this paper, two and three dimensional finite element analysis of disconnected pile-raft systems are performed on three case studies including a 12-storey residential building in Iran, a 39-storey twin tower in Indonesia, and the 256m height of Messeturm tower in Frankfurt, Germany. The analysis include different geometrical parameters, e.g., pile spacing and embedment length, arrangement and raft thickness for foundation system to obtain the optimized design functions and to clarify the role of each parameter and method of analysis. The parametric study results and comparison to a few field measurements indicate that by concentrating the piles in the central area of the raft foundation leads to the optimum design with the minimum total length of piles. This achievement can be considered as a criterion for project cost efficiency. On the other hand, disconnected piled-raft systems can significantly reduce the settlements and raft internal bending moments. Finally, the comparison indicates that simple and faster 2D analysis has almost the identical results to 3D analysis which is complicated and time consuming.

Jan 1, 2008

By Chu E. Ho

Field load tests on deep slurry stabilized bored piles have shown that end bearing resistance was unreliable due to soft toe conditions caused by debris accumulation at the bottom of the hole during pile installation. This is true whether bentonite or polymer slurry was used. Skin friction resistance was less affected by the slurry and is more reliable. A design strategy is proposed which ensures that an adequate factor of safety against the ultimate shaft resistance is maintained for any chosen design working load, such that a pile settlement of 12mm would not be exceeded.

Jan 1, 2002

By G. G. Goble

Significant progress has been made in the past decade in determining the load bearing capacity of pile foundations. Developments in the means of prediction of pile capacity as limited by soil strength have been substantial, particularly in the use of dynamic methods. The use of currently available equipment, analytical procedures, and practices in the field, will often produce material economies on a job by allowing increased loads with proven factors of safety. This approach justifies the minimum number of piles required for a safe foundation in a wide range of job sizes and soil conditions. To avoid exposing the reader to excessive detail in the body of this paper, technical topics have been covered more thoroughly in several appendices. I. Wave Equation Analysis of Piles Appendix A II. Dynamic Monitoring and the Pile Driving Analyzer Appendix B III. Case Method Capacity Calculation Appendix C IV. Case Pile Wave Analysis Program Appendix D 1 Preliminary Analysis In designing driven pile foundations, there must be a close relationship between design, construction control procedures, driving practices, and the size of the job. Small commercial buildings or residences involving loads that are only a fraction of the pile capacities do not justify the expense of detailed design processes or elaborate construction controls. Nevertheless, some preliminary analysis of the job requirements and a limited subsurface investigation must be made to understand existing conditions and the possible foundation solutions. In other words, it is necessary to determine that driven piling is the best overall choice of foundation.

Jan 1, 1988

By Eric M. Klein

As part of the Woodrow Wilson Replacement Bridge project several damaged wetland and environmental areas were to be mitigated. One of the mitigation projects consisted of constructing a Denil fish ladder around Peirce Mill Dam in Rock Creek National Park, Washington, D.C. The dam is a historic structure operated by the National Park Service. The fish ladder is located between the east abutment of the dam and Beach Drive, a major collector road. Construction of the fish ladder required removal of a portion of the east abutment and an excavation that extended about 22-ft below the pavement of Beach Ave. It was not possible to close Beach Drive except for very brief intervals or at night; therefore, a support of excavation system that would minimize disruption to the public was required. The high groundwater required that the groundwater be cut off prior to excavation; the random rubble and soil fill, and shallow but erratic rock surface precluded driving sheet piling. A jet grout system was selected because the grout probe could penetrate the rubble fill, stabilize a variety of soil conditions, and cut off the ground water prior to excavation. It was not possible to construct a stable wall without tiebacks or soil nails. Given the schedule and tight working conditions it was decided that soil nails through the jet grout wall facing would be the most cost effective method, as it did not reduce the working space as rakers would and would be more cost effective than prestressed tiebacks.

Jan 1, 2006

By Luca de Sanctis

The analysis of piled raft foundations in layered soils may be performed by 3D finite elements or by approximate procedures. Among the latter, the code NAPRA (Russo, 1998) is based on the method of the interaction factors and accounts for soil layering by the so called Steinbrenner approximation. A comparison between the results of 3D FEM and NAPRA for some reference layered soil profiles shows that the approximation is fully acceptable for engineering purposes, provided the stiffness of the single pile is properly selected. The interest of the conclusion lies in the fact that the amount of work needed to model a practical problem by NAPRA is but a fraction of that needed by FEM modelling.

Jan 1, 2002

By Patrick Bermingham

The advancement of hydraulic impact hammers has followed the general advancement of hydraulics. The construction industry has been revolutionized by the application of hydraulics in excavators, cranes and, of course, in the hydraulic vibratory driver/extractor, which has become a standard tool. The innate ability to move a large mass with a very small displaced volume has given hydraulic power the advantage over previous power mediums. Recent development of more specialized and complex seal configurations and compounds has greatly improved the reliability and permitted the use of higher pressures in hydraulic systems.

Jan 1, 1987

By B. H. Moore

The opportunity to evaluate the pile design procedures used on a major project is an infrequent occurrence. It is even more infrequent that the project involves piles with significant tension and horizontal capacities. This report synopsizes over twenty years of design and construction experience on just such a major pile founded structure. The philosophy governing foundation design procedures is described and discussed. The order and extent of full scale pile testing are evaluated. Principal points in the specifications are established and their effect on construction progress and claims are noted. The report concludes with recommendations for future projects.

Jan 1, 2010

By Sangseom Jeong, Moonkyung Chung, Junyoung Ko

"Abstract The plugging effect of open-ended piles in sandy soil is analyzed by full-scale field test and plugging measurement. PLR (plug length ratio) measurement data from 144 field cases are analyzed with pile diameter. Based on the plugging measurements, PLR of open-ended piles which have above 1000mm diameter is predicted to be above 0.9. Through plugging measurements, a new empirical method is suggested for quantifying the plugging effect of open-ended piles. The proposed PLR equation is possible to predict the behavior of soil plug in the preliminary design stage. In addition, in order to investigate the behavior of the soil plug of open-ended pile, field load tests are performed on instrumented three piles driven into sand. It is obtained that the resistance components of open-ended pile are separated by double-walled pile system. It is found that inner shaft capacity is developed nearby pile tip. However, upper soil plug did not influence the inner shaft capacity. Also, it is found that all test piles are floating piles and unplugged condition because the sum of inner shaft capacity and outer shaft capacity is calculated about 58 to 76% of the ultimate bearing capacity.INTRODUCTIONIn Korea, a number of huge construction projects such as harbor terminals, offshore grand bridges, and lifeline systems are progress in urban and costal area. In these areas, steel pipe piles are frequently used to support high-rise buildings and heavy weight structures for ensuring structural safety rather than serviceability limit capacity. Also, steel pipe piles are frequently used in civil engineering structures because they have many advantages such as high-load bearing capacity, light weight and outstanding workability. The mega foundations of grand bridges and high-rise buildings are required in geotechnical engineering. Large diameter driven piles are frequently used in several projects.Many specifications such as API, FHWA and AASHTO have been reported as a design guideline of plugging effect, however , the current design method for plugging effect of steel pipe piles are mainly based on the our knowledge derived from observation of the model test or the small diameter pile load test. Therefore, these specifications have limitation to apply the large diameter steel pipe piles.Much work has been done to study the plugging effect by many researchers. Yamahara (1964) reported that soil plug has been modeled as a thin disk element as shown in Figure 1, since the increment of radial strain of the soil plug can be neglected due to high rigidity of the pile compared to that of the soil plug. Klos and Tejchman (1977) reported that the end bearing capacity of open-ended piles was almost equal to that of a closed-ended pile when penetration depth of pile was above 15times the pile diameters by model tests. Paikowsky and Whitman(1990) reported fundamental studies on mechanism of plugging effect in sand. Paik et al. (2003) reported that empirical relations for plug load capacity, annulus load capacity, and shaft load capacity of open-ended piles are proposed based on the model pile tests. As discussed above, much work has been done in the area of plugging effect. But little work has been done to study the plugging effect by full scale field tests."

Jan 1, 2014

By Andrew J. Brennan, Jonathan A. Knappett, Lewis Hamilton, Michael J. Brown

"Abstract This paper investigates the compressive behaviour of screw piles in sands and the key design parameters which control this. These types of foundation elements have typically been used as screw anchors onshore (i.e. for their tensile capacity), but there is increasing interest in their potential use as compression piles for supporting offshore marine renewable energy (MRE) devices (e.g. wind and tidal turbines) in deeper water. For such foundation applications, the compressive capacity is as important as the tensile capacity and is not well understood, particularly in cohesionless soils which are a likely seabed condition in MRE applications. A 1-g laboratory study was initially conducted on small scale model screw piles in sand beds of various relative density between 25 – 88%. These experiments were used to validate a Finite Element (FE) model having a stress-dependent constitutive model, making it useful for future up-scaling of the pile size for field applications. Following validation, the FE model was used to conduct a parametric study on the effects of flange spacing ratio (s/Dflange) and flange to shaft diameter ratio (Dflange/Dshaft). By using a validated FE model for this study, it was possible to observe the failure mechanisms (through the shear strain distribution) within the soil and correlate these with the pile capacity. This information was then used to comment on the most optimal (cost-effective) pile design for supporting compressive loads. This study represents a key step towards producing design tools appropriate for the design of screw piles in MREapplications.IntroductionAs defined in this paper, screw piles consist of a central small diameter hollow steel shaft, around which thin circular steel flanges run. Their principle of operation is that the flanges are spaced so as to trap the soil between them, thereby acting as an equivalent solid pile of the outer flange diameter, with a fully-rough ‘shaft’ interface (as shearing is soil-soil). One of the most important design decisions relates to the spacing of the flanges – if the flanges are spaced too far apart, then the soil will not be effectively trapped and the pile have a lower axial capacity and stiffness (controlled by the shaft friction along the central shaft and the bearing resistance arising from the individual flanges; If the flanges are spaced too close together, then there are potentially flanges which are not contributing to the pile capacity, therefore making the pile more expensive than it needs to be."

Jan 1, 2014

By A. K. C. Chan

Recent hotel investment projects in China often involve very tight programmes for design and construction. An example given in this paper involves a 24-storey reinforced concrete hotel tower with 460 bedrooms and a 3-level podium commercial complex. The building is supported by relatively widely spaced columns and shear walls below which 88 number large diameter piers were excavated through fill, silty and bouldery clay on to dolerite and slate at depths between 15 to 3 0m below ground level. Whereas much experience has been accumulated in Hong Kong, hand-excavated pier foundation was only adopted for the first time in Dalian. This paper describes and discusses the various factors influencing the choice of the type and design of the foundation system. The criteria for determining appropriate founding levels are then explained. During installation, revisions to the acceptance procedure were made to cater for local conditions. Emphasis is placed on the role of the geotechnical engineer in making on-site decisions during construction. The advantage of the foundation system in accommodating on-site changes resulting from local complex ground conditions is demonstrated. The pier foundations were successfully completed ahead of programme.

Jan 1, 2010

By Arturo Ressi di Cervia

The utilization of diaphragm wall construction in Hong Kong began in 1974 with the construction of the New World Center, the first diaphragm wall job built in the British Colony. That landmark job of which I am presenting a few slides and a schematic description, embodied all of the difficulties and problems which are encountered in the difficult geology of Hong Kong. A small rocky island in the South China Sea, Hong Kong provides one of the finest natural harbors in the world. It is its splendid harbor, coupled with the enterprising attitude of the Hong Kong Chinese and the laissez-fair attitude of the British government which has resulted in the explosive growth of this speck of land soon to revert to the political control of mainland China.

Jan 1, 1993