Search Documents

By Dardis J. T. II, P. G. Reinhall

"Impact pile driving of steel piles in marine environments produces extremely high sound levels in the water. It has been shown that current pile driving noise attenuation techniques provide limited noise reduction because significant noise is transmitted through the sediment into the water. To solve this problem, we have developed a double walled pile to decrease the total noise transmitted into the water.The double walled pile consists of two concentric tubes connected by a special driving shoe, allowing for an air gap between the two tubes. The double walled pile is driven into the sediment using traditional equipment by striking the inner tube only. The air gap between the inner and outer tube prevents the radial deformation wave produced by the pile hammer from interacting with the water and the sediment. In one embodiment of the double pile design the inner tube can be removed and repeatedly reused.In this paper we report on the results from a recent full scale field test in Puget Sound, Washington. The use of these double walled piles reduces the peak sound pressure over 20 dB relative to single walled piles. We also show that only a 3 to 6 dB reduction is obtained when a bubble curtain is used on a single walled pile.INTRODUCTIONImpact pile driving of steel piles in marine environments produces extremely high sound levels in the water. It has been shown that current noise attenuation techniques provide limited noise reduction because the noise from pile driving is transmitted through the sediment into the water. In [1,2] we showed, using modeling and field data, that the primary source of underwater sound from an impact driven pile originates from radial expansion of the pile as the compression wave propagates down the pile after each strike. The radial expansion is coupled to the compression wave through the Poisson’s ratio of steel. As discussed in [1], the supersonic radial expansion wave (with respect to the water) produces an acoustic field in the shape of an axisymmetric cone, or Mach cone. We showed in [3] that the ability of any sound shield that surrounds the pile in the water only (such as a bubble curtain or a surrounding double wall engagement) to attenuate the sound in the water is limited by the fact that an upward moving sound Mach wave is produced in the sediment and is transmitted into the water. To improve the performance of bubble curtains and other noise shields in the water, it is necessary to attenuate the noise emanating from the sediment into the water. Figure 1 illustrates how sound from the seabed leaks out from the sediment, limiting the effect of the surrounding bubble curtain."

Jan 1, 2017

By Peter Cali

There is one organization in Sweden, The Swedish Deep Stabilization Research Centre, which has been working with these questions and there is also a project, Eurosoilstab, within European Union to take a manual for deep stabilization.

Feb 10, 2003

By Gary T. Brill

In the presentation, the development and new applications of the jet grouting technique in the North America are briefly introduced at first and followed by the outline and advantages of Jet Grouting. Several recent projects for jet grouting are presented in which the applications to underpinning and excavation support, foundation, groundwater barrier and seismic stabilization are briefly discussed.

Feb 10, 2003

By Mousaab Majar, Nikolaus Schneider

The technical challenges for accurate drilling positions increase with deep underground structures in inner city areas. Designed for jet grouting, specific sensors have been developed to record the alignment of rods during drilling by integrating microchips into the drilling rods. By feeding the rod with constant electric current, microchips, integrated in special couplings, can be read during the drilling process and tracked on monitors installed in the operator’s cockpit. The orientation for the drilling rod is provided by magnetic points and a compass, positioned above ground on the drilling rig. In combination with asymmetric drilling bits, it is now possible to steer the drilling hole to predetermined positions to compensate for deviations in deep bores. This type of drilling rod for jet grouting has been used in Berlin since summer 2019.

May 1, 2022

By Leonhard Weixler, Jean Wehbe, Gordian Ulrich, Franz-Werner Gerressen

"As alternative energy industries pick up speed internationally, and as government regulation and restriction limit the use of impact hammers due to environmental limitation from construction induced noise during pile driving operations, unconventional solutions for more complex offshore foundation installations have become a necessity. Manufacturers and equipment suppliers race to develop alternative techniques to accommodate for offshore foundation construction in various soil conditions and at greater water depth. The FLYDRILL, and the Seabed-Drill BSD are two innovative systems for the installation of offshore monopiles with reduced environmental impact.INTRODUCTIONThe FLYDRILL and the Seabed-Drill were born from techniques in the design and construction experiences gained from land based foundation drilling systems over the past 25 years. As the alternative energy industry ventures into uncharted territory of deeper water for offshore wind farms, fast current regions for tidal energy, and increasingly challenging soil conditions and project complexity, the advancement and development of new innovative equipment system and drilling techniques have become a necessity.The systems described herein show the development of the so called “FLY-Drill” system, and the all new “Seabed-Drilling” equipment applied at the first ever made job using a seabed drilling rig.FLY DRILLThe FLY DRILL method is a completely new concept for bored piling. The drilling unit with rotary head, Kelly bar, and drilling tool is suspended by the hoist rope of the base carrier crane. The hydraulic power for the drill unit is provided from the base crane.The drill head is fixed on the casing with a hydraulically operated clamping system during the drilling operation. When emptying the drilling tool, the clamp cylinders are opened and the complete unit is swung sideways."

Jan 1, 2017

By Michael J. Marasa

"Geotechnical engineering and construction primarily relies on the subsurface characteristics of the particular site; however, obtaining both accurate and precise information on those features is challenging due to the numerous factors involved in testing procedures used to analyze varying site geology. This includes a detailed and thorough geotechnical investigation to understand the site conditions, allowing the implementation of the most practical and economical solution.This paper presents a case history of the installation of wick drains and construction of aggregate piers on the site of a large facility to be constructed in Memphis, Tennessee. Throughout intensive subsurface investigations, highly variable soils were encountered, requiring settlement control and increased bearing capacity. This paper will discuss the design and installation of the systems constructed, and procedures and execution of the work to ensure design specifications were achieved.BackgroundA 1.4 million square foot expansion directly adjacent to an existing 1.1 million square foot distribution facility in Memphis, Tennessee was planned to serve as a centralized facility for increased production. The first phase of construction included an 858,000 square foot warehouse and parking lot for approximately 400 trucks to the north of the existing structure. The anticipated column load for the warehouse was 125 kips; slab design bearing pressures ranged from 200 to 500 pounds per square foot (psf) and elevations ranged from EL. 264 to 282. Parking lot elevations ranged from EL. 264 to 290, requiring a design life of 10 years with an estimated 100 in- and out-bound trucks daily and maximum weight of 80 kips per truck. The second phase of construction took place east of the existing structure, and included a 794,000 square foot multi-level warehouse, a 100,000 square foot office, and additional employee parking. The anticipated column load for the second warehouse was 225 kips and slab design bearing pressures ranged from 200 to 500 psf. Elevations ranged from EL. 267 to 282. Anticipated column loads from the office were 25 125 kips, with slab design bearing pressures ranging from 100 to 200 psf. Due to the varying elevations within each planned footprint, up to 18 feet of new fill was required to match the existing structure’s finished floor elevation (FFE) at EL. 282."

Jan 1, 2017

By Philip Derbyshire, Dale J. Scheffler

"Continuous Flight Auger (CFA) piling is a variation of Augered Cast-In-Place (ACIP) or augercast piling. In both cases a continuous auger with a hollow stem is used to drill a hole and a pile is formed by injection of cementitious material through the hollow stem as the auger is withdrawn. CFA differs from conventional American ACIP by the use of concrete rather than grout to form the pile, and by the type of equipment used to advance the auger into the ground and withdraw it. CFA installation uses a European style rig (i.e. fixed mast and rotary system) which can produce greater crowd and usually has a larger rotator or drill motor than the standard augercast setup. A standard augercast setup will consist of a lattice-boom crane and a set of leads to house the drill motor and auger. The auger size will range up to 24 inches (610mm). With CFA rigs larger diameter piles can be constructed, 24 to 36 in dia. (610mm to 915mm) are common and the technique has been applied with diameters up to 48-inch (1220mm). CFA makes use of sophisticated computer controlled monitoring systems, which have more recently been introduced for conventional ACIP piling. Developments in CFA have taken place over the last 25 years in Europe and particularly in the UK, but are relatively new in the USA. One application is in the construction of secant (overlapping) piled retaining walls. D.J. Scheffler Inc. recognized the potential of the CFA system following visits to the UK and has introduced its use into California for both secant piling and other applications.BACKGROUNDThe high price of real estate in many of the favored areas of California has increasingly led owners to want to build basements under their houses to increase the floor space available on a lot. Many of these areas are by the coast where the ground conditions are predominately granular and the water table is high. Conventional shoring and dewatering systems have often caused problems with adjoining properties. Clearly tangent walls are not suitable in these conditions because of leakage and loss of ground. The secant pile system, using CFA techniques, has proved very effective at overcoming the problems experienced by other methods. Other applications for CFA secant walls have included use for an emergency job on a highway following erosion caused by unusually heavy rainfall.METHODThe concept of secanting piles, whereby primary(female) piles are installed first and then secondary (male) piles are cut into the primary piles is not new. The method has been known for more than 30 years. Originally ‘Benoto’ grabbing rigs, developed in Japan, were used together with sectionalized double skinned casing and oscillators.This early method was slow, although very effective. More recently high torque rotary machines have been used. Contractors in the UK have increasingly used CFA techniques to further improve productivity of this type of piled wall. The improved capabilities of piling rigs available, as well as developments in concrete technology and instrumentation, have made this possible."

Jan 1, 2005

By Dale E. Berner

A new navigation dam at Olmsted on the Ohio River will be built "in-the-wet" using a lift-in construction method by the Washington Group/Alberici Joint Venture for the U.S. Army Corps of Engineers, Louisville District. Up to 4,000-ton precast concrete dam shell segments will be prefabricated on the Illinois riverbank and lowered into the river on a marine skidway and cradle. A 4,500-ton capacity catamaran crane barge will lift the precast concrete shells and lifting frames from the cradle, and transport them partially submerged to a piled foundation pre-installed underwater. Tremie concrete will be used to compositely connect the shells, piles and sheet pile cut-off walls. This paper focuses on the pipe-pile foundations for this half-mile long navigation dam, and for the temporary precast yard and marine skidway. The dam foundations are designed to resist large ground motions from the New Madrid Fault Zone, and selected production piles are designed to serve as landing piles to support the shells during the construction process. Specific foundation issues addressed in the paper include: pile load tests; production field testing requirements; controlled fixity 24-inch diameter pipe-pile design including seismic considerations; cut-off wall design; sheet pile cellular fixed weir design; isolation jOint design; and temporary works foundation designs for both the precast yard and the marine skidway, including testing of 42-in diameter pipe piles.

May 11, 2007

By David White

When finished (projected completion in 2016) the Hong Kong-Zhuhai-Macau Bridge Project will comprise three cable-stayed span bridges and a 4.15 mile immersed tube tunnel - linking Hong Kong to Macau and the mainland Chinese city of Zhuhai. The design included two artificial Islands to serve as the transition structures for the tunnel to bridges, entailing a massive seaborne land reclamation project, and the use of thousands of sheet piles, and man-hours. The challenges of driving individual steel sheet in 100? of water are well known, let alone in the open waters of the South China Sea. In 2010 a joint effort between American Piledriving Equipment (APE) and Allnamics Pile Testing Experts convinced the Chinese contractor First Harbor Marine Group China that a massive multi-vibro hammer can be used to drive 130? long, 72? diameter steel pipe piles weighing 662 US tons each into the sea bed of the South China Sea for the Hong Kong - Zhuhai - Macau bridge artificial islands. Combining APE?s hammer design, production and operation know-how with the pile driving simulation and installation know-how of Allnamics made it possible to show the feasibility of driving these gigantic piles into bottom of the sea to the required depth.

By David White

"When finished (projected completion in 2016) the Hong Kong-Zhuhai-Macau Bridge Project will comprise three cable-stayed span bridges and a 4.15 mile immersed tube tunnel - linking Hong Kong to Macau and the mainland Chinese city of Zhuhai. The design included two artificial Islands to serve as the transition structures for the tunnel to bridges, entailing a massive seaborne land reclamation project, and the use of thousands of sheet piles, and man-hours. The challenges of driving individual steel sheet in 100’ of water are well known, let alone in the open waters of the South China Sea.In 2010 a joint effort between American Piledriving Equipment (APE) and Allnamics Pile Testing Experts convinced the Chinese contractor First Harbor Marine Group China that a massive multi-vibro hammer can be used to drive 130’ long, 72’ diameter steel pipe piles weighing 662 US tons each into the sea bed of the South China Sea for the Hong Kong - Zhuhai - Macau bridge artificial islands. Combining APE’s hammer design, production and operation know-how with the pile driving simulation and installation know-how of Allnamics made it possible to show the feasibility of driving these gigantic piles into bottom of the sea to the required depth.INTRODUCTIONThe challenges of driving individual steel sheets in deep water are well known, let alone in the open waters of the South China Sea. Often the challenges of construction are overcome with engineering or equipment. The challenges of China’s Hong Kong-Zhuhai-Macau Bridge, on the drawing board since 1983, were to overcome both. The challenges of overcoming the skepticism of the Chinese Engineering community would be another story.The finished project will comprise three cablestayed span bridges and a 4.15 mile immersed tube tunnel linking Hong Kong on an eastern span to the China mainland cities of Zhuhai and Macau via two western spans."

Jan 1, 2017

By Paul Pedini

The challenge of Contract C19E1 of Boston's Central Artery Project called for the construction of two roadways under the commuter rail yard at North Station. Two options were offered for the method of their construction: Slurry Wall Roof-First or Soft Ground Tunneling. The instability of the indigenous soils seemed to rule out the use of tunneling, so the slurry wall method was chosen. However, these soils were incapable of holding up during slurry trench excavation. After many episodes of ground loss on early panel excavations, Modem Continental Construction suggested a method of trench wall stabilization. The Contractor (MCC) both suggested wall stabilization method and requested that the owner participate in the funding for the effort. The Project and the Contractor were able to agree on a solution which resulted in collapse-free excavation...and found an innovative way to fund the solution.

Jan 1, 2002

By Dharmil Patel, Michael J. Chow

"Construction progress is nearing completion at a Brownfield Site for a 100,000sf mixed-use 10 story building plus cellar for Silver Star Motors including a two-floor pre-owned Mercedes Benz showroom; high-end residential rental studios, 1, 2, and 3 bedroom apartments; and penthouses on the upper two floors. Excavation through impacted soil extended to 15ft depth. Project is approximately 7 ft north of a NYCT subway station, portions of the SOE are within inches of a 6ft diameter NYCDEP Sewer, and cellar extends below the depth of adjacent structures, requiring over 200 lf of underpinning.A complex series of earth retention systems was utilized consisting of underpinning, drilled-in soldier piles (micro-piles), timber/concrete lagging, soil anchors and inclined rakers supported by a partially constructed foundation mat. Foundation mat subgrade was approximately 4 ft below the groundwater level creating more challenges during underpinning and achieving suitable foundation subgrades. All construction was undertaken on a non-union basis.This paper describes the design, construction, and lessons learned for the multiple earth retention systems, Brownfield Remediation requirements, instrumentation, and monitoring used to manage complications of building adjacent to an active subway station, in close proximity to existing utilities, with underpinning and mat foundation installation below the water table.Results of the instrumentation program are summarized which utilized an AMTS, monitoring prisms on adjacent structures, automated seismographs, and manual NYCT surveys."

Jan 1, 2016

By Dale Berner, Michael O’Sullivan

"This article focuses on lessons learned from innovative designs including in-the-wet construction methodology and modified foundation conditions, for two United States Army Corps of Engineers (USACE) megaprojects. Olmsted Dam FoundationThe over $2 billion Olmsted Dam on the Ohio River is currently under construction 16 mi (29.6 km) upstream from the confluence with the Mississippi River. The project is under the jurisdiction of the Louisville District of the USACE. It will consist of an 800 ft (244 m) long tainter gate section, a 1,400 ft (427 m) navigable pass, two boat abutment sections, a fixed weir section, and upstream and downstream scour protection. The Olmsted Dam and its two 1,200 ft (366 m) locks, which were built in 2002, will eventually replace both Locks and Dam #52 and #53, both built in 1929, and thereby bring significant benefits to the Ohio River navigation system.In 2002, the Jacobs/COWI JV completed the design of the dam; which was an engineering challenge for several reasons. A significant consideration was its proximity to the New Madrid Fault, which could impose an 8.4 Richter scale seismic event on the structure, which is located in an area of potentially liquefiable alluvium. The extensive seismic analysis performed by the designer included a response spectra analyses, lateral pushover analyses of pile foundations, hydrodynamic added masses, pile group effects, and the development of kinematic motions as a result of the soil-pilestructure interaction."

Jan 1, 2016

By Grischa Dette, Thomas Schröder, Holger Merski

For the construction of the tunnel for the new Berlin S21 light rail line, a construction pit had to be built below the crossing B 96 federal road. For this purpose, the construction pit M’ has been built beforehand as a preliminary structure for the later S21 Berlin. A crucial element of this structure is a 2.50 m deep reinforced concrete deck slab which carries the B 96. During the later construction of the S21, it became clear that the existing preliminary structure could not be used without major modifications. Consequently, the construction pit design was gradually upgraded – still with the aim of retaining the basic concept of a trough structure with a jet-grouting cut-off. As construction progressed, for reasons of stability it became necessary to develop a fundamentally new concept with an underwater concrete base replacing the jet-grouting cutoff. This paper describes the planning and construction of a cut-and-cover structure with an underwater concrete base – a layout that brings with it the difficult task of underwater excavation and concrete placing without direct accessibility from above. Special emphasis is placed on describing the innovative approaches in connection with a remotely controlled underwater dredger from the Norwegian offshore industry for excavation works. Furthermore, the sophisticated underwater technologies for concrete placing in the confined surroundings are described.

May 1, 2022

By Lisheng Shao

Soil mixing and jet grouting have been widely used to support heavy structures such as tanks, cement silos, and storage buildings. Although the installation methods vary between soil mixing and jet grouting, the end product of soil-cement columns behaves similarly in supporting structure loads. In many cases, soil-cement mass treatment offers the owner savings over driven/drilled piles. This paper discusses the design methodology, production work, and quality control, with supporting figures, of a recent large complex tank farm project. The project consisted of constructing six above-ground steel storage tanks and an approximately 700-foot-long fill slope. The tank farm site is located in an industrial area of southern California, with highly variable subsurface conditions consisting of compressible soils and buried construction debris. The compressible soils necessitated that the new tanks be supported on deep foundations. A test pile program performed previously at the site showed that conventional driven concrete piles were not feasible because of buried construction debris, therefore a soilcrete system was proposed. Site design included evaluating the total and differential settlement and column group bearing capacity under both static and seismic loads. Extensive field and laboratory testing confirmed the design soil-cement strength and modulus of both the soil mixed and jet grouted soil-cement columns. The project operation and quality control programs are also included in this paper.

Jan 1, 2010

By Dan A. Brown, Rich A. Lamb, Paul J. Axtell

"Over the last 10 years, the Minnesota Department of Transportation (Mn/DOT) has had a very active program of replacing many major bridges, large structures spanning the Mississippi River. The deep foundations for these new structures include both drilled shafts and large diameter open-ended driven steel pipe piles. Most of these projects included load tests, both axial and lateral.The geology of this area of Minnesota includes some interesting foundation challenges, including highly organic and compressible very soft silts and clays to very dense sand and gravel overlying sedimentary bedrock. In some cases scour requires embedment into rock, and the bedrock formations may range from very soft sandstone to very hard dolostone. Artesian groundwater conditions can sometimes complicate drilled shaft construction, but the rock is otherwise very favorable for drilled shafts. Experience with the open-ended driven steel pipe piles (typically 42 and 48 in, 1.07 and 1.2 m diameter) suggest that these piles most often penetrate even dense granular materials to achieve bearing on rock. Experiences with drilled shafts socketed into the soft sandstones demonstrate that these rocks provide very favorable conditions for drilled shafts, so long as suitable construction practices are followed. Here we present several recent case histories regarding the foundation design and construction of major bridge projects in the vicinity of Minneapolis, Minn., including the Wakota Bridge, the I-35W replacement, the Lafayette Bridge, the Hastings Bridge and the St. Croix Bridge. Some lessons learned from construction and load testing of both types of foundations are described along with implications for design in similar soil and rock conditions."

Jan 1, 2013

By Michael Arnold, Robert Bachus, Michael Bracher, Jamey Rosen, Robert Roff

"For a high hazard USACE facility, the Center Hill Dam in Tennessee, several disparate streams of data were compiled into a single geospatial and relational enterprise data management system to store, analyze, visualize and distribute the data collected during installation of a deep cutoff wall. These data streams included historical drawings and pre-construction plans and grouting records; geological data from boreholes; attributes of barrier wall elements; element verticality data analyzed from multiple measurement methods; and concrete field and laboratory analytical data. A previously developed data management system developed by the authors, WallTracker, was extensively modified to also include manually collected and real-time measurements from several types of dam monitoring instruments. The system now uses enterprise database technologies with Geographical Information Systems capabilities to manage and relate these data streams into a common platform and allows access to the raw and interpreted data via web and desktop-based interactive tools, including interactive map and cross-sectional viewers and other graphical and tabular reporting tools. One of the primary benefits of this system is the neartransparent interaction that is possible with the Nashville District of USACE on the project. These techniques can now be effectively incorporated into systems that address the unique construction and data management tracking requirements for dams, dikes, and levees.IntroductionThe Center Hill Dam rehabilitation, as with other deep foundation installations, requires the contractor to collect a substantial amount of information over the course of the project, both for internal quality control of construction progress and methods, and for demonstrating compliance with owner specifications. This paper discusses techniques used at Center Hill Dam for consolidating, visualizing and analyzing construction and instrumentation data using relational database and Geographic Information Systems (GIS) technology, collectively referred to as an Information Management System (IMS).The remainder of this paper presents the needs and objectives of the IMS, the components and data flows involved, the capabilities and user interfaces of the systems, and the benefits for the end users."

Jan 1, 2017

By David R. Shields, Michael T. Bracher

"The $330 million (U.S.) Dana-Farber Cancer Institute’s Yawkey Center for Cancer Care (Yawkey Center) sits in the heart of Boston’s Longwood Medical Area. The Yawkey Center is a cutting-edge cancer care facility that houses Dana-Farber’s adult clinical care and clinical research programs. Standing 14 stories above grade, it includes 7 stories of underground parking extending 75 ft (23 m) below ground. The structure is on a 198 by 186 ft (60 by 57 m) site sandwiched between Dana-Farber’s 13-story Richard A. and Susan F. Smith Research Laboratories Building, the Medical Area Total Energy Plant (MATEP), Jimmy Fund Way, and Brookline Avenue, a busy four lane artery through the heart of the Longwood Medical Area. Together with Simon Design Engineering, the project structural engineer, GEI Consultants designed an innovative foundation and excavation support system to isolate the building from ground vibrations generated by the adjacent MATEP power plant. In effect, the Yawkey Center is a 21-story free-standing structure that starts 7 stories below grade.The MATEP facility provides power for 9 million sq ft (840,000 sq m) of occupied space in the medical area. There are six 32-cylinder diesel engine generators in the facility that produce low-frequency ground vibrations in the 10 Hz range, similar to the natural frequency of typical building elements. The resonant response of the Yawkey Center building structure to these ground vibrations would affect the performance of sensitive medical research equipment and cause an unacceptable environment for clinical care.The soil profile at the site consists of stiff clay, fine sand, glacial till, and bedrock consisting of hard metamorphosed conglomerate. In-situ measurements of ground vibrations performed in boreholes showed that there was little attenuation of the vibrations with depth in the soil layers overlying the bedrock, but the vibration amplitude in the bedrock was markedly lower than in the overlying soil. Based on this data, an innovative foundation system was designed to support the building on bedrock located up to 110 ft (34 m) below ground surface, while isolating it from the surrounding soil. This was done by physically separating the below-grade parking garage floors from the perimeter foundation walls to create a free-standing structure supported on the bedrock"

Jan 1, 2012

By Andres M. Baquerizo, Matthew E. Meyer, Carlos Ortiz

"The Metropolitan Miami development, a downtown mixed-use complex developed by Miami-based MDM Development Group, has weathered the economic downturn by adapting to the needs and pressures of the local market. The development (a.k.a. Met Miami) epitomizes the term “mixed-use urban development” with its combination of condominium ownership, rental apartments, hospitality, office and retail components within Miami’s urban core. Initially conceived and conceptualized in 2004, the development has gone through several concept changes. Today, the global USD $900 million development approaches completion.The foundation evaluation, design and construction for this development included the use of innovative and state-of-the-art augered-cast-in-place (ACIP) piles. The testing for these elements included (1) the first-ever, multi-level O-cell load test of an ACIP pile, (2) a world record 5,200 ton (46,261.5 kN) equivalent top load test of an ACIP pile, and (3) continued the advancement of the ACIP pile industry to include the deepest and largest diameter pile installation to date. Those dimensions were up to 36 in (914 mm) in diameter, and 120 ft (36.6 m) deep. The project showed ACIP piles were a proven alternative for structures exceeding 70 stories in South Florida.The development includes four parcels. Met 1 and Met 2 are completed, and the construction of the Met 3 development is just beginning, with completion expected in 2014. Once the Met 3 development is completed, the design and construction phases of the project will have spanned a decade. The Met Square portion of the development, which will be a retail and cinema component, is proposed for the parcel between Met 1 and Met 2."

Jan 1, 2012

By Michael E. Ameel

The vibrated beam method of installing a vertical barrier wall is one of the least applied techniques, yet given certain site conditions and constraints, it is a cost-effective and proven method of controlling lateral groundwater flows. A recent full-scale application of this technique demonstrated its usefulness at an active manufacturing facility located in Northern Wisconsin. At this site, a 3,233 foot long cutoff wall was keyed into an underlying bedrock, which was located an average of 40 feet below the ground surface. Using a slag cement-clay based slurry, a 1E-7 cm/sec or less, nominal 4-inch wide cut-off wall was constructed using the vibrated beam method. Challenges included working around an active manufacturing facility with minimal access to the work area; installing the wall through a very dense glacial till; minimizing soil excavation volumes of potentially impacted soil; and, working around and adjacent to numerous active utility lines without impacting the facility operations. At utility locations, the vibrated beam wall was supplemented with a jet grout panel wall, without the need to bypass or otherwise interrupt any of the plant?s utilities. Quality control consisted of the monitoring and measuring of slurry parameters, survey control, and real-time monitoring and documentation of all critical barrier wall installation parameters. A vibration monitoring plan was also implemented to measure vibrations at utilities and adjacent facility structures. Proper equipment selection, significant up-front planning and close coordination with the facility resulted in a safe and successful project. The work was completed ahead of schedule during the 2009 construction season.

Jan 1, 2010