Search Documents

By Prodyot Kumar Ray, Sudip Kumar Koley, Aminul Islam, Somnath Banerjee

One of the most important topics in the construction industry is the building of railway embankments. Being such a delicate and significant structure, it is crucial to properly design the embankment and build it while adhering to all statutory criteria and design guidelines. A railway embankment's subsoil condition and fill material, groundwater table, dynamic and static loads during operation, and embankment geometry are some of its most crucial design considerations. This paper discusses the likely causes of the collapse of a railway embankment in eastern India as well as the suggested rehabilitation scheme. It was observed that an embankment collapsed in the aforementioned area during a inccesent rain. Along with the side shifting of a cantilever retaining wall that was positioned at the bottom of the embankment, the embankment next to the railroad track settled vertically. According to the available geotechnical report, the sub soil strata in half of the area adjacent to the embankment profile, where the embankment height gradually decreases from maximum height, is stiff to hard clay with an undrained cohesion value of around 50 kpa followed by dense sand, and the sub soil strata in the other half is soft clay with an undrained strength of 15 kpa. As a result, in the rainy season due to the sudden increase in the water table, the self-weight of the embankment increased and further caused the under-laying soft clay to get squeezed away and settle. Due to this squeeze/settlement effect of the soft clay layer, the retaining wall got disturbed along with the generation of an undulated embankment top profile. As a remedial measure, it is proposed to construct a contiguous bored pile wall at the toe of the embankment to stabilize the slope, and additionally, compaction grouting is recommended beneath the embankment to improve the soft clay. In order to carry out the analysis, certain commercial geotechnical software like Slide, Wallap, and Plaxis 2D are used. The factor of safety of the embankment slope considering the above restoration scheme is adequate under static and seismic conditions.

Sep 1, 2022

By C. N. Baker

The design and construction of drilled piers through water bearing and caving soil conditions are discussed. The need for close cooperation between the design engineer and contractor in both the design and construction stage is outlined. Four case histories illustrating the design and construction considerations for four different problem soil and ground water profiles are presented, including the field testing and observation procedures that were utilized to confirm that the design inten. was accomplished. Requirements advisable when placing concrete under water in a cased environment and when placing concrete under slurry in an uncased environment are described.

Jan 1, 2010

By A. Le Kouby

We present in this paper the results of a parametric study carried out in a calibration chamber on instrumented model piles. The aim is to point out group effect on piles within a group through their resulting shaft friction and tip resistance. The methodology relies on the study of the influence of adjacent piles on a "reference" pile. The soil used is a silica sand (Fontainebleau sand). The influence of parameters like pile spacing, number of piles and installation order are evaluated. The results show a positive effect on shaft friction of the group effect and a negative effect on tip resistance. Efficiency factors are defined in order to have a better view on the parameters influencing the response of the pile within a group.

Jan 1, 2006

By Takeo Asanuma, Sachihiko Tokunaga, Hirofumi Taguchi, Yasuhiro Ootsuka, Yosuke Tanaka

The Cement Deep Mixing Method (CDM Method) is a ground improving method that has been used for mainly offshore sites to strengthen the soft ground below the sea bottom by injecting and adequately mixing cement slurry with soft soil into the ground to form a ground-improving column. In recent years, the CDM Method has increasingly been adopted for ground- improving work as part of liquefaction countermeasures and earthquake-resistant reinforcement in the shallow waters of river mouths and inland waters. In consequence of that, a pontoon-mounted CDM Method (CDM- FLOAT Method) has been developed for shallow waters, which is equipped with a land-type mixing machine combined with system management equipment and a tide level-based control function. This CDM-FLOAT Method can be deployed at work sites where the conventional offshore-use CDM barge cannot be employed. This report describes the CDM-FLOAT Method and the scope of applications together with construction work procedures, and a representative case of use of the CDM-FLOAT Method is introduced as an example of earthquake-resistant reinforcement of the existing embankment of a canal.

Jan 1, 2015

By D. E. Sherwood

Twelve toe grouted, and eleven ungrouted piles, founded in very dense sands have been analysed to establish how toe grouting enhances pile performance. It is shown that pile stiffness is greatly increased, and that pile bases work effectively. This is in contrast to ungrouted piles, where some milli­meters of base movement may be required before the base is mobilised. Grouting appears to recover most of the disturbance caused during construc­tion, but in general does not enhance the ultimate bearing capacity of undisturbed ground.

Jan 1, 1989

By Z. Q. Bian

The wireline sampling originates from core drilling in rocks. The authors combined the wireline sampling technique with conventional undisturbed soil samplers, including Osterberg sampler, Denison sampler and double tube barrel, and then developed the wireline samplers of WPS, WSS and WSR models. These samplers are able to sample various soils. They reserve all the advantages of the original samplers, and moreover, they are noted with quick hoisting and lowering by wire rope. Therefore, it becomes an efficient new technique of sampling undisturbed soil from deep foundation.

Jan 1, 2010

By A. A. Gupte

Auger piling system which was developed in the United States in the 1940's is gaining acceptance in many parts of the world. Although primarily used to support foundations, the system is very useful for many other applications such as soil anchors, temporary and permanent earth retention systems, restricted headroom piling and underpinning of existing foundations. In this paper, review of current construction design techniques for the Auger piling system for earth retention and underpinning of structures is presented.

Jan 1, 1989

By H. S. Radhakrishna

Foundations supporting power transmission and communications towers are subjected to both compression and uplift loads, often of a cyclic nature. Some novel foundations, combining the beneficial features of grouted and helix anchors with that of compression piles and grillages, were developed by Ontario Hydro during the construction of high voltage transmission lines in Ontario, Canada. In addition to meeting the load requirements, the foundations permit easy installation in swampy areas and also minimize impact on environmentally sensitive terrain. This paper describes the features of these composite foundations and outlines the performance criteria used for their design and installation on the basis of load test results.

Jan 1, 2010

By Makarand G. Khare

Though the phenomenon of dragload is known for many decades, there is a lack of clear guidelines to evaluate the amount of dragload. The development of dragload depends on relative movement between pile and surrounding soil which is a complex phenomenon and requires a detailed numerical analysis. Bitumen layer has been used in the past with varying degree of success in reducing the dragload but the reduction appears to depend on number of parameters. No procedure is available in literature to estimate the dragload when a slip layer is applied on pile surface. This paper investigates performance of two commercially available bituminous coats to reduce the negative skin friction on pile. Direct shear test apparatus was used to model the interface friction between soil and coated pile surface. The lower half of direct shear box was replaced with either a concrete block or a mild steel block representing pile surface. Two types of bituminous coats namely Shalikote and bitumen having penetration value of 30-40 were evaluated in this study. Shearing resistance of pile material-coat-soil is found to be influenced by normal stress, coat thickness, and rate of shear. Laboratory results are compared with published field data where coated and uncoated piles have been load tested.

Jan 1, 2006

By E. Ulrich Klotz

It is difficult to predict accurately the capacity of driven piles in sand. In practice, this uncer­tainty either leads to conservative designs if the capacity is under-predicted, or worse, if the capacity is over-predicted, it can lead to severe foundation problems. One significant possible cause of the problem is that currently available semi-empirical design methods do not capture the fundamental mechanisms that govern the load capacity of driven piles in sands. As part of a recent research project at City University centrifuge tests on a driven model pile in sands have been undertaken. A fully instrumented model pile was constructed and pushed into samples of quartz and carbonate sand thus covering a wide range of mineralogies. Tri-axial tests were used to determine the fundamental patterns of behavior of the sands. This allowed a general framework to be established, in which the in situ stress:volume relationship is shown to govern the capacity of the pile. The paper sets out with a brief introduction of the experimental techniques used in the study. The results of the pile tests are discussed in detail with particular attention given to distribution of the radial stresses along the pile shaft. Existing design methods for piles in sand are then discussed in the light of the new understanding gained from the research, highlighting their deficiencies and suggesting an improved approach.

Jan 1, 2002

By Issa S. Oweis

Two Towers are currently under construction in Central Moscow in the Russian Federation. Building A is a 96 story tower and Building B is a 65 story tower. The columns in both structures bear on a thick concrete mat that is supported on drilled shafts, 1.5 m in diameter. The shafts derive their capacity from weak limestone with layers of marl. Assigned allowable shaft loads were initially based on rock strengths that were later verified by load tests using the Osterberg Cell. One of the load tests was carried to near failure which allowed refining socket friction values that were later used in the design of Building A. All shafts were advanced using an auger and concrete placed in the dry. Grout tubes were placed with the reinforcing cage which allowed grouting of the limestone in contact with the shaft. Load sharing between the shafts and the mat was approximated using published methods as well as site specific finite element analysis. This paper covers the methodology of design, analysis of the Osterberg results to derive non-linear stiffness of the rock and differences between finite element analyses and results by approximate methods.

Jan 1, 2007

By Ryan Law

Ground energy systems are being installed in increasing numbers in the United Kingdom. This is particularly true in London where planning regulations require larger scale developments to provide at least 10% of their entire energy demands from renewable sources. A common approach has been to use the groundwater from the Chalk aquifer as a source of energy. This paper explains the potential long and short term sustainability problems with groundwater based systems sited in central London (or any other urbanized area). It also outlines an approach to site testing and numerical modelling to ensure that the system functions well throughout its lifetime. This approach is then applied to a project located in central London.

Jan 1, 2008

By Kiyotaka Ohno, Nobushige Yasuoka, Yosuke Hioki

"The diameter of improved columns adopted by the original DJM Method had been 1000 mm, however, in order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter expanded to 1300 mm was developed between 1998 and 2001 and has been widely applied since then. From the first application of EX-DJM in January 2002 for a first construction project, the total volume of improved soil has reached 325,000 m3 in 17 projects up to September 2014. Because of the advantages of the EX-DJM such as reduction of construction costs and periods leading to reduction in the number of improved columns, adoption of this method is expected to increase in the future. This paper describes the advantages of the EX-DJM, its construction results and case examples including those applied to restoration projects after the Great East Japan Earthquake, 2011.1. BACKGROUND OF DEVELOPMENTThe Dry Jet Mixing (DJM) Method is a soil stabilization method in which a powdery or granular binder is pneumatically fed into and mixed with soft soil to induce chemical reactions that stabilize and strengthen the soil. It was developed by government - private collaboration in Japan between 1977 and 1979. Up to March 2014, the total volume of soil improved by DJM method reached 33,500,000 m3. The initial diameter of improved columns of the original DJM Method was 1000 mm. In order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter 1300 mm was developed between 1998 and 2001.2. ADVANTAGES OF EX-DJMThe construction equipment for the EX-DJM consists of two major parts, which are DJM machine and binder plant are shown in Fig. 1.The construction machine is of double mixing-shaft type with its column diameter expanded to 1200mm or 1300mm. In association with the increase in the column diameter, the binder feeder has also increased its discharge rate by approximately 1.69 times. Same as the increase rate of the area of original diameter 1000mm to diameter 1300mm are shown in Fig. 4."

Jan 1, 2015

By Alp Gokalp

The aim of this article is to present an application of jet grouting technique in stiff clays for foundations of the natural gas combined cycle power plant, under construction in Aliaga, Turkey. The plant site is in the Aegean coastal region and 60 km north of Izmir. The foundation soil is composed of quaternary alluviums on top and tuff base rock. The thickness of the alluvium varies between 16 m to 30 m. Groundwater was observed 2.5 m below the ground level. At the design stage, settlement analyses were carried out for the various buildings and facilities in the power plant. Based on the analyses, it was predicted that total and differential settlements are not tolerable, thus jet grouting is implemented as a ground improvement under the majority of the foundations of the power plant. This paper also describes the selection of jet grouting technique, application type and details of the process parameters such as injection pressure, number and size of nozzles, lifting and rotation speeds. Prior to the commencement of the jet grouting works, a number of preliminary parameter tests and preliminary pull-out tests were carried out throughout the site in order to define and verify the jet grouting process parameters to achieve the required diameter of 600 mm and minimum jet grout strength of 3.2 MPa. Moreover as part of the comprehensive quality control and quality assurance program pursued in the project, a number of tests; such as continuous coring, integrity testing, installation of confirmatory jet grout columns, were carried out during the production of jet grout columns.

Jan 1, 2002

By Racquel Nottingham, Freddy Lopez, Ole Gadermann

The ongoing urban development is a global phenomenon, placing has high demands on urban infrastructure (housing, public services, transportation, telecommunications, etc.). Micropiling is one of the most successfully implemented deep foundation technologies in urban interventions, and in densely populated and built-up areas. The use of micropiles enabled the implementation of several solutions within short time frames, with minimal disturbance to the daily activities of the population. Since urban interventions usually represent a very important investment and have an economic impact, special attention should be paid to the serviceability of the urban infrastructure in the middle and long term. For the foundations, the design loadbearing capacity of the used structural elements needs to be guaranteed during the planned life time of the structures. In the case of micropiles, it must be ensured that the steel load bearing elements are effectively protected against corrosion. This paper presents the structural design of permanent self-drilling micropiles, subject to tension due to uplift loads. For the case study, different micropile systems - available worldwide - will also be evaluated. For the afore mentioned micropile systems, the design considerations regarding the durability of the reinforcement, based on their corrosion protection approaches, will be presented in this paper.

By H. R. Masoumi

This paper presents a numerical model for the prediction of free field vibrations due to vibratory and impact driving. As the focus is on the response in the far field, where deformations are relatively small, a linear elastic constitutive behavior is assumed for the soil. The free field vibrations are calculated by means of a coupled FE-BE model using a subdomain formulation, proposed by Aubry and Clouteau (1992). The model is validated by means of the results of Kaynia and Kausel (1991) for the impedance of a single pile. First, the case of vibratory pile driving is considered, where the contributions of different types of waves are investigated for several penetration depths. The results show that in the near field, the response of the soil is dominated by a vertically polarized shear wave, whereas in the far field, Rayleigh waves dominate the ground vibration and body waves have been importantly attenuated. Second, the case of impact pile driving is considered. A linear wave equation model is used to estimate the impact force during the driving process. Furthermore, it is investigated how the soil stratification influences the ground vibration considering the case of a soft layer on a stiffer half space. The results show that when the penetration depth is smaller than the layer thickness, the layered medium has a small influence. However, when the penetration depth is larger than the layer thickness, these effects become more significant. Finally, the computed ground vibrations are compared with experimental data reported in the literature.

Jan 1, 2006

By Ronald E. Walkington

The U.S. Department of Energy (DOE) is building the world's newest accelerator-based, pulsed-neutron system, called Spallation Neutron Source (SNS). The facility, located in Oak Ridge, Tennessee, is a partnership of six DOE national laboratories - Argonne, Brookhaven, Jefferson, Lawrence Berkeley, Los Alamos, and Oak Ridge. Oak Ridge has the responsibility for managing the partnership and ultimately operating SNS. SNS will provide opportunities for up to 2,000 researchers each year from universities, national laboratories and industry from around the world for basic and applied research and technology development in the fields of materials science, magnetic materials, polymers and complex fluids, chemistry and biology. When completed, this state-of-the-art research facility will provide neutron beams that are 12 times more intense than any other such source in the world. Most of the world's neutron sources were built decades ago. Therefore, it is easy to understand how SNS will provide new research opportunities unavailable elsewhere, and at the same time restore United States leadership in neutron sciences. Neutron scattering research provides valuable information about materials that cannot be obtained through microscopy, X-rays, spectroscopes, or other techniques. The information gained from neutron scattering research leads to improved materials that are used in high-temperature superconductors, powerful lightweight magnets, aluminum bridge decks, jet aircraft, compact and computer discs, magnetic recording tapes, shatter-proof windshields, and many other applications. SNS is like a flashing strobe light providing high-speed illumination of an object and will record the structure of physical and biological materials from plastics to proteins. Because neutrons have no charge, they can penetrate more deeply into materials than do X-rays, light, or electrons and thus reveal bulk structure and properties of materials. SNS will help to understand and "engineer" better materials and the manufacture of better products at the atomic level. Our high-technology society demands new materials that are stronger, lighter, and cheaper yet perform well under severe conditions. SNS, which is designed with the future in mind, will be the leading neutron research facility for many years to come.

Jan 1, 2001

By Gordon Chen

As part of a value engineering envisioned by East Coast Slurry, Weidlinger Associates, Inc. designed a unique elliptical slurry wall cofferdam for construction of the 65 ft. deep MWRA North Dorchester Pump Station. A conventional rectangle cofferdam with multiple levels of bracing would have been time consuming and costly and imposed a significant obstruction to the pump station construction. A circular slurry wall, while eliminating the bracings, conflicted with adjacent structures and required excessive backfilling around the final pump station structure. The ellipse shaped cofferdam fit the needs of the project well; however, it created a significant design challenge without the use of bracings. Unlike a circular cofferdam which primarily only has hoop stresses, the ellipse still has to be designed for horizontal bending moments in each panel because of the non-axial symmetric conditions. The more eccentric the cofferdam shape; the higher the horizontal bending. The challenge was to develop a three dimensional finite element model that could analyze both the hoop stresses and horizontal bending stresses above and below the bottom of excavation induced by soil and water pressure and unbalanced construction surcharge loads. This paper discusses the techniques used to model the soils and structure interactions and results of stresses on this challenging unbraced configuration.

Jan 1, 2010

By Lawrence F. Johnsen, Marc J. Gallagher

"Micropiles are small diameter, bored, grouted-in-place piles incorporating steel casing and/or reinforcements. The omission of micropiles from most United States building codes has resulted in the application of varying standards for design and installation. The ADSC/DFI Micropile Committee has developed a proposed section for the 2006 edition of the International Building Code (IBC 2006) covering micropiles. The proposed IBC 2006 micropile code section is presented, along with comparisons to existing micropile codes and guidelines. A discussion section is provided to clarify sections of the proposed code. IntroductionMicropiles, defined as small diameter (typically less than 12 inches outer diameter), bored, grouted-in-place piles incorporating steel casing and/or reinforcements, are becoming common foundation elements for new construction, retrofits, and emergency repairs. Developed in Europe in the 1950's and used in United States practice since the late 1970's, micropiles are typically not addressed in building codes, particularly in the United States. As a result, micropiles are often reviewed by building officials to a variety of standards, including drilled shafts, caissons, cast-in-place bored piles, and concrete filled pipe piles. None of these adequately address the unique design and construction aspects of micropiles. Therefore, it became apparent to the foundation design and construction community that a micropile-specific code section was required.To that end, the International Association of Foundation Drilling and the Deep Foundations Institute (ADSC/DFI) Micropile Committee appointed a subcommittee in October 2003 to develop and submit a proposed micropile code section for the 2006 IBC. The subcommittee members included the two co-authors, as well as Tom Richards (Nicholson Construction Company), Tom Armour (DBM Contractors, Inc.), John Wolosick (Hayward Baker, Inc.), Allen Cadden (Schnabel Engineering) and Matt Niermann (Schnabel Foundation Company). At the time of the writing of this paper, the proposed code section has been presented at the IBC public hearing during which it was modified slightly. Final adoption (or rejection) will be determined by the IBC at the final action hearing in September 2005. The attached code section is the revised version following the public review hearings."

Jan 1, 2005

By Goudschaal Mark R.

"The Museum of Science and Industry U-505 Submarine Relocation project in Chicago, IL consisted of building an underground reinforced concrete vault (37' deep) for the Museum's new U-505 exhibit. This WWII submarine was captured in 1944, had been located outdoors at the Museum since 1954 and was lowered into its new exhibit area in 2004. A unique combination of earth retention, water cut-off and underpinning systems allowed a forty-two foot (42') deep excavation underneath th is historic museum. The museum - originally built in 1893 for the Chicago World's Fair - was closely monitored for building movements throughout construction. The underpinning systems, construction activities and monitoring results are presented herein. IntroductionThe historic U-505 German submarine at the Museum of Science & Industry was restored, moved approximately 1,000' and then lowered into its new indoor home (Figures 1, 2 and 3). The new underground exhibit opened this year celebrating the 61st anniversary of the German submarine's capture on June 4, 1944. On this historic day, Captain Daniel V. Gallery, a Chicago native, led the Navy in the siege of this submarine near the coast of Africa. This U-boat was the only German sub captured by the United States Navy in WWII and the Enigma machines, codebooks and publications recovered from the sub helped the war effort."

Jan 1, 2005