Search Documents

By Mohammad Nasim

Vertical expansion of existing structures frequently requires foundation retrofitting to enhance the capacity of existing foundations for supporting additional loads. Owing to their small diameter, a variety of suitable drilling methods available for installation, and smaller installation equipment capable of operating under limited headroom conditions, micropiles are often preferred for foundation retrofitting. This paper presents a case history demonstrating application of micropiles to underpin the existing foundation of the Washington D.C. Children?s National Medical Center (CNMC) for its future expansion. Located at 111 Michigan Avenue in northwest Washington, DC, portions of the hospital currently extend five stories above grade and three levels below-grade as parking garages. The hospital intends to expand the surgical wing up to the current build out (five stories) above the remaining portion of the existing parking garage. The original foundations consist of 80-ton Raymond Step-Tapered piles. New loading on the foundations required each Raymond pile to be capable of supporting 150 tons. Results from quick load tests on existing piles indicated that two entire column lines (Column Line A and B) would experience loads beyond their capacity, requiring enhancement of the existing foundation at these locations. The design and construction of the foundation upgrading work was particularly challenging due to various project constraints related to a high groundwater table, micropile installation under limited head room, and ensuring that the parking garage remained fully operational for the entire duration of construction. The paper presents the challenges faced during testing of existing foundations amid a high groundwater table, design developments of underpinning options to support the additional column loads, difficulties and challenges encountered during installation of the micropiles and construction of the micropile pilecaps, and value engineering options developed during various phases of the project. Understanding that micropiles are often a preferred option for foundation retrofitting, the case history is expected to provide a baseline design approach and innovative solutions to typical challenges faced during construction, thereby reducing potential cost overruns during design development and construction of similar future projects.

Jan 1, 2008

By Joseph C. Gillen

This paper discusses the design, construction, and performance of the support of excavation system used at The Atlantic Building jobsite. The support of excavation system had to be adaptable to the different conditions surrounding the site. These conditions included support of four historic building façades, including the nine-story Atlantic Building, as well as support of three historic row-houses along two walls. Directly adjacent to the site is the historic Ford?s Theatre and townhouse. Across a 15? alley is the American Immigration Lawyers Association (AILA) Building, and across a 30? alley is the Federal Election Commission Building and another ongoing excavation. Of historical note, these two alleys were the escape route for John Wilkes Booth following his assassination of President Lincoln. With the excavation being 53? to 58? deep, the system included driven and drilled soldier piles, drilled bracket piles, and two modified tangent walls. The bracing included tiebacks, corner braces, wales, cross lot struts, and a specially designed support system for the nine-story façade. The footprint of the excavation included 12 corners and all alleys and streets were to remain open during construction. The performance requirements for system movement at Ford?s Theatre and AILA Building were ½ inches in the horizontal direction. The modified tangent walls were used in these areas to provide stiffness. The soil conditions at the site were fill material on top of a shallow, sandy, silty, gravel layer on top of a deep layer of soft organic silt and clay. Below the silt and clay layer was fine sandy material at the subgrade.

Jan 1, 2006

By Sun Shao Xian

The Port of Shekou is situated at Shenzhen Bay on the east side of the Pearl River estuary. Geological condition of the site is quite complicated. On top of the sea bed, there is a layer of soft silt 8 - 14 m thick. Under the soft silt, there are intercalated layers of sand, silt and clay. Average surface elevation of the underlying undulatory weathered bed rock is about - 20 m, with a variation of about 10 m. In certain locations, the weathered bed rock is covered with a layer of silt 3 - 4 m thick. This paper gives brief account of three types of wharf structures which are of particular interest, constructed in the last few years: (A) Platform type wharf structure with frontal sheet piling and steel raking pile in the rear; (B) Relieving Platform type structure with steel sheet piling and inclined anchoring HP pile ; (C) Steel pipe pile row supported apron added to a marginal quay. Average construction time of a deepwater berth is about six months.

Jan 1, 1991

By Martin B. Hudson, Daniel Brescia, Zhangwei Ning

Due to the complexity and sensitivity of surrounding environments, instrumentation and monitoring (I&M) is critical for many urban deep excavations. The objects to be monitored include shoring bulkheads, retained embankments, adjacent buildings and roads as well as underground utilities. However, there are also plenty of constraints on the implementation of I&M such as: congested site space, difficult access to instruments, coordination among multiple contractors, and installation permits for private or public properties. Because of these constraints, sometimes the implementation of the initially planned I&M is delayed, its scope is reduced, and/or the continuity of monitoring is interrupted. For these reasons, it is important to implement the I&M with robust and redundant capabilities while providing minimal interference to the project construction and schedule. This paper describes state-of-the-art I&M technologies including automatic motorized total station (AMTS) with camera and automatic leveling device, reflectorless AMTS and IoT- based wireless sensors based on a case study of an on-going deep excavation project. INTRODUCTION In urban environments, deep excavations requiring the construction of temporary shoring bulkheads are becoming increasingly common, with the associated need to provide protection of the surrounding built environment during construction. Protection of the surrounding environment requires planning, engineering, construction, monitoring, and excessive shoring movement mitigation. The I&M is a vital component of the deep shoring implementation. In public projects, geotechnical I&M is often placed within the general contractor’s scope, whereas the majority of deep excavations are privately undertaken. For those private developments, sometimes the developer contracts the geotechnical I&M directly with the project geotechnical engineer or by a geotechnical I&M specialist hired by the project geotechnical engineer. In either the public project or private development case, the effective deployment of the I&M system relies heavily on coordination and collaboration with the project contractor.

Jan 1, 2018

By J. P. Welsh

Ground Modification construction is rapidly evolving in the United States. An assessment of the construction status of Ground Modification methods with their dates of introduction and general acceptance in the United States is summarized. Seven of these techniques are discussed in depth with short case histories; namely, Dynamic Deep Compaction, vibro-compaction, vibro-Replacement, chemical grouting, compaction grouting, slurry grouting and jet grouting. Additional case histories are presented to illustrate the trend of combining Ground Modification techniques to solve specific site problems.

Jan 1, 2010

By Ray Schmahl

The Glenwood Canyon is a 13 mile long river gorge formed by the Colorado River approximately 2 miles East of Glenwood Springs, Colorado and approximately 150 miles West of Denver Colorado, (See Drawing #1). The canyon walls rise some 800 feet from the river elevation on either side of the river. The South-side river bank is occupied by the Denver and Rio Grande Western Railroad. The Northside is currently occupied by completed sections of Interstate 70 and US Highway 6. The railroad was built in the late 1800's and a hydroelectric power generating station was built in about the center of the canyon in the early 1900's. The Highway 6 platform was completed in the 1930's. The design and alignment for Interstate 70 thru Glenwood Canyon began in the early 1970's. The Highway thru Glenwood Canyon was designated a scenic Highway by the United States Congress, thereby allowing certain deviations from standard Interstate requirements. Environmentalists objections to the construction of Interstate Highways thru Glenwood Canyon resulted in especially careful design to avoid adverse environmental impacts. As a result, in many areas the new Highways will have restored the canyon to its more native configuration than what was the case in the building of the US 6 Highway platform.

Jan 1, 1990

By the courtesy of Metropolitana Milanese (Milan Underground), roost of the delegates visited on April 12, 1991 the tunnel of "PORTA VENEZIA" STATION of MILANO RAILWAY LINK. The "PORTA VENEZIA" STATION will be the most important in the link and it will he also the largest underground project of the whole railway transport network in Lomhardy. The particular conditions of the soil and the collocation of site in the center of Milano have required new technologies and the technical solution applied to this job is called "Cellular Arch Method" by its designer Prof. P. Lunardi. Our sincere thanks go to Prof. P. Lunardi and Eng. E.M. Pizzarotti of Rocksoil, Milano who have kindly furnished us a technical description of this method. Eng. Pizzarotti was the guide during the visit and gave all the technical explanations to the delegates. THE "VENEZIA" STATION IN THE 2PB SECTION OF THE RAILWAY LINK The excavation of cavities in loose ground, exceeding a certain dimension and at shallow depth, is not feasible using traditional methods: in fact it is not possible to consolidate the ground around the cavity in such a way that homogeneity and resistance is sufficiently guaranteed.

Jan 1, 1994

By Sanket Rawat, Ravi Kant Mittal, Vikash Prasad

"The understanding of the response of pile foundations under various types of loads is a necessary prerequisite to analyze and design them properly. Therefore, this paper highlights and compares the provisions available in Indian Standard IS 2911:2010 to estimate the capacity of laterally loaded pile foundation with the provisions available in different country codes and existing literature. Comparisons are made between the Indian standard method, Broms method and Matlock & Reese method for the analysis of laterally loaded piles due to popularity and prevalence of the later methods in design offices worldwide. This has been achieved using a parametric study on pile embedded in pre-consolidated clay and sand for both fixed head and free head case in terms of displacement and ultimate load capacity. It has been found that there are various limitations to the Indian Standard method associated with various cases such as short pile analysis, complete moment distribution etc. Therefore, suitable recommendations have been made on the basis of the above comparison to improve the accuracy of the design in Indian perspective. The proposed comparison and subsequent area of improvements will present the design engineers all across the globe, a broad sight of design specifications of laterally loaded piles.INTRODUCTIONPiles in groups are very often subjected to both axial and lateral loads. In the 1960’s, designers used to assume that the piles could carry only axial loads and the lateral load is to be carried by batter piles. However, later, a large number of load tests authenticated that vertical piles also can transfer lateral loads through shear, bending, and lateral soil resistance rather than purely acting as axially loaded members. Initial attempts to analyze laterally loaded piles used the finite-difference method, as described by Howe (1955), Matlock and Reese (1960), and Bowles (1968). Matlock and Reese (1956) used the finite difference method to get a series of non-dimensional curves to enable the user to input the appropriate curve with the given lateral load and estimate the ground-line deflection and maximum bending moment in the pile shaft. Later, Matlock and Reese (1960) extended the earlier curves to include selected variations of soil modulus with depth."

Jan 1, 2017

By Gyimah Kasali

Rapid Load Testing was performed as part of an extensive drilled pier testing program for the University of California Berkeley Capital Improvement Program. The purpose of the program was to: (1) Verify the axial compressive design capacity values for the planned 24" piers, and to estimate the capacity of the existing 30" CIDH piers, and (2) To evaluate the seismic performance of the proposed drilled shafts. The Fundex PLT was used since the loading period of the PLT is very similar to the period of a seismic event, making it an ideal tool to model the pier response to seismic events. "Performance-based design" of structures subject to seismic loads has been of particular interest to UC Berkeley Seismic Review Committee and the Pacific Earthquake Engineering Research Center. The comparison of static tests to Rapid Load testing also provided valuable correlations. The program represents one of the most comprehensive drilled pier test programs on the West Coast. The testing program consisted of Rapid Load Testing using the Fundex PLT on 6 drilled piers. Rapid Load Tests were followed by conventional static compression and tension tests on selected piers, followed by another cycle of rapid load tests on the statically tested piers. The piers featured extensive instrumentation to allow detailed interpretation of the test result. Correlations were drawn to compare static load test result to that of the PLT in the particular soil profile, and the PLT also provided the data to analyze the ultimate seismic capacity of the piers. The load test results indicate that the ratio of interpreted failure load from the PLT data to the corresponding load from the static load test data is about 1.2 to 1.3 for the clayey soils underlying the test site. The results also indicate that the PLT offers an economical approach to defining the stiffness of drilled pier foundations subjected to seismic loads for use in performance-based design.

Jan 1, 2002

By P. M. Wiltcher

The construction of a deep structural slurry wall in a restricted city centre location is always a challenging prospect. However, when the city is London and the site is bounded on two sides by high level canals and a main traffic highway on the third, the challenges are greater than usual. The paper discusses the design considerations required by the principal contractor to accommodate a single high level lateral support, value-engineered, bottom-up construction technique and the impact this had on the design detailing and construction of the slurry wall panels. This paper discusses the logistical challenges successfully overcome during the construction of 65,000sq ft of 40inch thick, 80ft deep structural slurry wall in the City of London. The paper reviews the benefits gained from using the state-of-the-art hydraulic grab and rotator system. Technological advances in computer instrumentation and real time monitoring were utilised to assist the grab operators in consistently delivering deviational control during excavation better than 1:200. With working space always at a premium on construction sites, the need for high quality, pre-fabricated reinforcement cages has never been greater. This paper reviews the argument for off-site fabrication of reinforcement members.

Jan 1, 2006

By Mohammed Y. Fattah, Wissam H. S. Al-Sudani

"During installation of pile, a soil column is formed inside the pile. For small depths, the height of the soil column typically equals to the penetration depth (full coring state). As the penetration depth increases, the developed internal shear stresses become larger and reduce the amount of soil to penetrate. At the same time, the soil in pile at the bottom is compacted. This will continue until at a given moment, the soil column is a soil plug, and does not stop moving relative to the pile. This is because the shear stresses developed in the interior of the pile are greater than the load-bearing capacity of the ground.This paper presents the results obtained from 40 model pile tests carried out to assess the effect of soil plug on the model pile capacity. The piles are embedded in sand of different densities with different lengths of piles and types of pile-ends. The model tests are divided into two parts according to the type of end of the pipe pile used in the model pile test. The first part consists of 32 model open-ended piles with different lengths of soil plug inside the pile. The second part consists of 8 model closed-ended piles.It was concluded that open-ended pipe piles behave as a closed-ended if the soil plug formed inside piles in state partial plug or full plug. Length of soil plug depends on the type of installation and relative density. The pile load carrying capacity in dense sand is several times greater than those in medium sands especially in cases of closed ended piles or open-ended since the pipe pile can produce external and internal skin friction in addition to end bearing resistance that makes the total pile capacity close to that of closed-ended pile. Whether open-ended piles are driven or pressed in the fully coring - fully unplugged mode or in the partially plugged mode, the plug does contribute to static pile base capacity."

Jan 1, 2014

By Tsunenobu Nozaki

"AbstractThe PRESS-IN METHOD is widely recognised as “an environmentally friendly piling method”. However, this characteristic is only one of the fundamental advantages of the method and this paper presents the most up-to-date capabilities of the method. Due to the evolution in recent years, the Press-in Method is now applicable to 2.5m thick retaining walls, over 50m deep foundations, overcoming rock conditions and confined construction conditions.The Press-in PrinciplesThe basis of the Press-in Method is simple. The Silent Piler presses a pre-formed displacement pile into the ground by static jacking force. The reaction for the Press-in Force is generated by gripping previously installed piles. As a pile is pressed into the ground, “A Pressure Bulb” is formed around the pile toe. Accordingly, higher bearing capacity can be generated compared to driven piles without disturbing the ground and producing any vibration. (A comparison of jacked, driven and bored piles in sand (2005), Deeks et al.)Applicable Pile ProfileThe Press-in Method is applicable to most of the steel piles available on global market i.e. U sheet pile in single form and pair, Z sheet pile, also in single and pair and Tubular Pile as described in Figure 2. Wall thickness of those piles can be 0.3m to 2.5m and moment of inertia of the wall ranges up to about nine million biquadratic cm per meter, which can deliver similar elastic modulus EI (kNm2/m) to 2.0m thick diaphragm walls and can be utilised for extremely deep excavations required in today’s construction industry"

Jan 1, 2014

By Tobias Hansson

The quality of Lime Cement (L/C) columns is to a great extent dependent on the installation procedure. At a site in the south of Sweden, the client reported problems with the installed columns. To evaluate the operator and equipment dependent part of the installation, Hercules Grundläggning AB was appointed as a competitor to the site contractor. The purpose was to install a number of L/C columns with equal installation parameters for both contractors. A total of 65 test columns were installed in June 1999. The geology is a typical Swedish organic soil profile with a top layer of peat overlying gyttja and clay. Two different binders were used in the comparison; blast furnace slag with cement and lime with cement. After installation, the quality of the columns was monitored by penetration tests and a column sampler for extracting whole columns. The column penetration test were performed 28 and 134 days after installation and extraction 134 days after installation. Inspection and tests of the extracted columns showed that by using a fully computer controlled procedure, the contractor produces columns of superior quality and homogeneity.

Jan 1, 2000

By Magnus Ruin

The dry deep mixing method for stabilization of soft soil has been used in the Scandinavian countries for 25 years. The typical application has been stabilization of soft inorganic clay. Today the method is used more frequently in organic soil with good results. The Limix System, introduced in the USA by Hercules Grundläggning AB and TREVIICOS Corporation, is a cost-effective dry deep mixing method used to stabilize most types of soft soil. This paper presents the general principles of stabilizing organic soil with the dry mix method and two case histories of soil stabilization projects in organic soil. Between October 2000 and June 2001 the Limix System was used in England to stabilize soft organic alluvium at the Channel Tunnel Rail Link, Contract 440. During year 2000 the Limix System was used in soft organic soil in Holland near the Groene Hart Tunnel entrance to support trench excavations for slurry walls and concrete barrettes.

Jan 1, 2001

By Prasenjit Basu

Drilled displacement piles are being increasingly used as foundation elements, particularly in projects requiring fast construction. Different types of drilled displacement (DD) piles are available in practice. DD piles are classified according to the drilling tool design and installation method. The capacity of a DD pile, depending on its type, is between the capacities of geometrically similar nondisplacement and full-displacement piles installed in the same soil profile. This paper provides an overview of the different types of DD piles and their installation techniques and describes three design methods used in practice. It also compares DD pile capacities obtained with these design methods for two different sites.

Jan 1, 2010

By A. L. Garassino

Dans cet article on parle sortout de l'approche de calcule pour les pieux charges horizontalement avec particuliere reference aux curbes p-y et è une solution semi-empirique qui prende en consideration les variations typiques du module du sol avec la deformation obtenue par les données expérimentales. 1. INTRODUCTION The analysis of the piles under lateral loads depends very strictly from the pile stiffness and geometry, from the soil type and from the strain field. Different approaches were adopted in solving the problem. Some Authors developed methods for estimating the ultimate lateral resistance of piles and pile groups by conventional static approaches, as the Brom's widely known (1964) or by the plane strain solution developed by Davis (1961) or by empirical engineering con­siderations l

Jan 1, 1994

By Peter Faust

The foundations for the new South Viaduct Bridge in San Francisco were extremely challenging due to the requirement for very large and deep piles installed adjacent to historic structures. Drilled shafts up to 12? foot in diameter were constructed to a maximum depth of 200? feet in alluvial soils and Franciscan Bedrock using an oscillator system for the installation of the permanent steel casing. This paper provides an overview of the construction techniques, the equipment, and the challenges associated with constructing 12? foot diameter shafts on this very complex project in one of the nation?s nicest landscape setting.

Jan 1, 2011

By F. Pagliacci

Retaining walls for the construction of underground urban infrastructures have to be executed considering the impact of a deep foundation job-site within an urban network. Traditional excavation systems, based on the use of grabs and bentonite mud, involve serious problems such as: the opening of trenches adjacent to existing buildings; the cleaning of the working area; the site installation for the production and storage of the bentonite mud; the transport and disposal of soil contaminated with bentonite mud. Alternative solutions have therefore been developed in order to overcome these problems. For temporary works soil consolidation methods, combined with the use of sheet piles, have been implemented, by a combination of traditional mixing methods and jet grouting systems to speed up the operations, consequently reducing the construction time. For permanent works two new techniques named respectively CSP (Cased Secant Piles) and CDW (Continuous Diaphragm Walls) have been studied, applied and tested.

Jan 1, 2000

By Seth L. Pearlman

Pin Piles are small diameter high capacity drilled and grouted piles also called minipiles or micropiles. They are ideal for building foundations on sites with poor ground conditions, sensitive surroundings, restricted vertical clearance, or difficult access. They are also well suited to foundation underpinning, arresting ground movements, and increasing the capacity of existing foundations. The major factors for selection of Pin Piles are reviewed; drilling, grouting, and design fundamentals are summarized; and a major case history is presented for the underpinning of the 43 story elevator core at the recently opened Mandalay Bay Resort and Casino in Las Vegas, NV.

Jan 1, 2000

By S. Ali Bastani, Ashley Varni

Design acceleration response spectra (ARS) are directly correlated with dynamic forces and estimated dynamic bridge displacements, which make them a critical aspect of dynamic bridge design. Nonlinear site response analyses are performed for a 1,400-linear-foot bridge site with a SC soil profile at the sides and a SF soil profile in the middle to evaluate the soil profile effects on the bridge analyses. One-dimensional seismic response analysis is commonly performed for site-specific response analysis. SHAKE or similar one-dimensional total-stress equivalent-linear approaches have been used since the 1970s. However, the equivalent linear method has deficiencies when the subsurface soils are susceptible to strain softening. Therefore, various assumptions are made when using the equivalent linear method by practitioners to estimate the SF soil profile site response. With recent advancements in constitutive models, effective stress models have become more popular. Although the effective stress models are generally more complicated and require additional input parameters, they shed further light on the liquefaction mechanism and its effect on the surface ARS. An equivalent-linear one-dimensional seismic response analysis and a non-linear effective-stress seismic response analysis, using DEEPSOIL, were performed to evaluate the ground surface ARS for a proposed bridge site in Orange County. The soil shear strengths were estimated based on cone penetration test results using empirical relationships. The shear modulus degradations (backbone curves) of soil layers were adjusted to match the estimated soil strength at failure. The ARS curves developed from each method were compared to determine the most suitable method for estimating a site-specific design ARS curve for a liquefiable site. Considering that the bridge abutments and the outer bents are founded in bedrock, while the middle bents are founded in liquefiable soils, ARS curves were created for each subsurface condition. Taking into account limitations of the structural analysis software, recommendations were made to combine the multiple ARS curves into a single ARS curve for the structural bridge design.

Jan 1, 2018