Search Documents

By Naoyuki Hanawa, Takeo Asanuma, Tatsuo Nagatsu, Sachihiko Tokunaga, Daisuke Nakagawa, Yoshiyuki Morikawa, Kazuhiko Ueno

"In the cement deep mixing (CDM) method, one approach to joint construction is creating a surface-contact joint. In this study, an unconsolidated-undrained triaxial compression test was performed on cement-treated soil specimens with joints artificially created by successive pouring. The effects of the presence or absence of such successive pouring joints on the strength of the specimens were then examined. The results showed that the compressive strength of the specimen decreased by approximately 0%–30% with a successive pouring joint.INTRODUCTIONIn the block type and wall type improvement patterns of the CDM(Cement Deep Mixing Method) application, an integrated body of soil-cement columns is constructed by partially overlapping individual treated soil columns. The overlapping operation should be implemented before the hardening of soils by cement progresses and thus, this operation is routinely performed in construction sites usually within 24 hours or within 48 hours at a maximum. However, when the operation is forced to be interrupted on account of a typhoon or any other adverse weather conditions, it is impossible to carry out the overlapping operation within the above time limitations. In such a case, it is necessary to improve the integrity between the treated soil columns solidified first and the treated soil columns to be constructed later.One of the methods that can be adopted is to prior agitate the target area by mixing blades “without cement”, integrating the preceding treated soil columns and the subsequently treated soil columns at construction joints. This method has been adopted so far in numerous sites because no additional materials or equipment are necessary. However, its effectiveness has scarcely been evaluated quantitatively in conventional studies.In the circumstances, the authors investigated in the present research the effect of the presence or absence of construction joints on the specimen strength by performing unconsolidated-undrained triaxial compression tests using specimens of cement treated soil artificially provided with surface-abutting construction joints.Therefore, this study examined the effects of the presence or absence of artificially created successive pouring joints on the strength of cement-treated soil specimens through an unconsolidated-undrained triaxial compression test."

Jan 1, 2015

By George Gazetas, Sissy Nikolaou, Fani Gelagoti, Irene Georgiou, Rallis Kourkoulis

"The need to shift geotechnical design from a “factor of safety” to a “performance based” design (PBD) approach has increased rapidly in the past years following examples from structural engineering. PBD supports sustainable engineered systems that target project-specific geotechnical behavior objectives and results in more rational and, in most cases, less conservative solutions. Resiliency, efficiency, risk optimization, and cost-effectiveness are key components of this approach. For design of retaining walls, the concept of mechanically stabilized earth (MSE) systems combines these attributes, while being environmentally friendly and adaptive to variable construction conditions. Natural hazards, such as earthquakes, may drive the design of MSE systems whose reliability depends on their performance under extreme events. In this paper, the authors compare the seismic response of an MSE steel-reinforced vs. concrete-reinforced retaining wall. The MSE system is composed of a grid of longitudinal and transverse ribs which internally enhances the capacity of the soil backfill. Results of fully non-linear twodimensional (2-D) numerical finite element analyses using two commercial programs with emphasis on the interface conditions are presented. The pull-out resistance of the grid used in the numerical simulation was evaluated from actual pull-out experiments. The results demonstrate a superior performance of the MSE system as compared to the concrete one, especially when subjected to strong seismic excitations.INTRODUCTIONThe idea of performance-based geotechnical engineering is not new, and has been evolving as our perception for ‘good’ performance has also evolved (Kramer, 2008). In early practice, the only criterion for achieving good performance was to avoid failure; designers had only to ensure that the available capacity of the geotechnical system is sufficiently higher than the expected demand (i.e. Load and Resistance Factor Methodologies). Yet, even when the key design requirements against collapse are satisfied, the system may still be placed into a condition in which the deformation constraints are not met (Bolton, 2012). To address these issues, geotechnical design has been developing into a predominantly performance-based approach that correlates deformation considerations to the severity of the experienced loading. As such, in earthquake-related problems, the definition of good performance of a geotechnical system is no more unique; for a low intensity earthquake the system should remain serviceable (i.e., the developed deformations should remain low), whilst for the design earthquake the maintenance of lifesafety is the single performance criterion."

Jan 1, 2016

By Clarissa Aguiar, Seok hyeon Chai, Thamer Yacoub, Sina Javankhoshdel

Sheet piles are used as an excavation support for soil retention. They are interlocked systems to form a wall for earth support along with anchors to provide an extra lateral support in excavations. The earth pressure against a sheet pile structure is not unique for each soil, but rather a function of soil-structure system. Movements of the structure with respect to the soil are primary factor in developing the pressure and thus the problem becomes indeterminate. In order to model a sheet pile wall for the analysis, structural element/interface can be used for the sheet pile. However, the use of the structural element with soil model alone is insufficient to simulate this soil-structure system as it fails to capture the slip condition between the sheet pile and the retained soil. In order to capture this slip condition, an interactive element can be used between sheet pile and soil to allow slip to occur. There have been many case studies where this method was used to analyze the response of the retained soil. Numerical studies have shown a good agreement with experimental results, but this stiffness is often not a well-known parameter, due to its complexity in nature of interactive behavior between soil and sheet pile walls. Also, many case studies are carried out with twodimensional analysis of the foundation, where three-dimensional analysis may be more suitable in some practical applications. In this paper, the interactive behavior of the element between sheet pile and soil is investigated with case studies for staged excavation using sheet piles and anchors. Then, investigation of a three-dimensional model is carried out by comparing with two-dimensional analysis.

By Kishore Kumar B., Eswaran Prasad C R, Srini Naik B., Ramakrishna Raju N

The authors through this paper intend to introduce the non-vibro technique of ground improvement by stone column, being used for the first time in India under the Western Dedicated freight Corridor in Mumbai area. New 2x25 KV double line dedicated freight corridor tracks, capable of carrying 32.5-ton axle load are proposed to be built on this stretch. Non-Vibro Displacement Stone Columns of 900 mm diameter were installed to improve the safe bearing capacity of the soft ground to take the loading of Dedicated Freight Corridor Railway embankment. Vertical footing load tests on single and three column groups were conducted to assess the improvement in the sub-surface condition after installation of stone columns. This paper describes load tests conducted on stone columns and analysis of the obtained results. The observed load settlement behaviour of the improved ground has also been presented. Behaviour of single and group of stone columns have been compared and criteria adopted for arriving at desired factor of safety based on the settlement observed, has also been discussed.

Nov 1, 2022

By Ryan T. Smith, Anthony Sahj, Alexander T. Darnell

Every second can count when trying to board a departing flight or catch a ride-share to your final destination. Hartsfield-Jackson Atlanta International Airport is in the midst of a project that aims to cut about 13 seconds between automated people mover trains (Plane Train) that move passengers between the terminals and concourses. The project involves extending the Plane Train tunnel west from its existing terminus under the domestic terminal. Working from inside non-public areas of the terminal, Keller North America, Inc. (Keller) incorporated systems of micropile-supported steel beams and grillage to both underpin existing columns prior to tunneling and support open-cut excavation at the tie-in of the new to the existing tunnel. Dewatering aided in mining a challenging section at the start of the drive of the mixedface, sequentially excavated tunnel and an automated instrumentation system monitored the performance of the construction and its impact to the terminal. Cut and cover egress and ventilation tunnels required braced support of excavation.

Oct 1, 2022

By Davide Grassi, Joel Joaquin Cortez, Giovanni Spagnoli, Nick Chittenden

Grouting is a technique used to improve the engineering properties of soils and rocks. Grouting techniques are classified under different criteria: injection method used, type of grout material injected, typical application, and the sequence of construction. The best-known criterion is the mode of entrance or admission of grout into the soil or rock. It is possible to identify therefore several grouting techniques: compaction, fracture, jet/mixing and permeation. The function of penetration grouting is to reduce the permeability of the soil or rock and/or increase the strength and density. In order to avoid displacement, permeation grouting shall be carried out at carefully controlled pressures and flow rates, using appropriate grouts. Colloidal silica is an innovative binder which has low viscosity (about 5 m·Pas), it is not toxic (pH lower than 9) and it is workable between +5°C and +45°C. This paper presents several case histories: a consolidation job related to the installation of a new sewer in North Italy in cohesionless soils, water stopping injection in a weathered granitic bedrock in California, permeation works in the US in sandy soils to improve excavation and the installation of sheet piles in the UAE. Results show that the colloidal silica an innovative and robust technology to perform grouting in very fine soils where conventional binders or micro-fine cements cannot penetrate.

May 1, 2022

By Patrick J. Hannigan, Seth Robertson, Frank Rausche, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (“TLBT”) and the conventional Bi-Directional Load Test (“BDLT”) are full-scale load tests where loads are applied bi-directionally to the foundation element. The BDLT uses an embedded loading source consisting of a jack assembly with one or multiple hydraulic jacks located between two steel bearing plates. As the jack(s) within the jack assembly is/are pressurized, the plates receive the load from the jack(s) and transfer these loads to the foundation element. In the case of the TLBT, the loads are also applied bi-directionally to the foundation element. However, in the TLBT case, the loading source is located above the foundation head. With the TLBT’s non-embedded and reusable load assembly, the loads are applied to the foundation using the steel shaft bearing and base bearing plates cast within the foundation. These plates are connected to the load assembly at the foundation head via Grade 75 or Grade 150, threaded, steel bars. This paper presents comparison results from a full-scale load test performed by both bi-directional load testing methods on adjacent test shafts. Details regarding subsurface conditions as well as test shaft construction and installation are included for the comparison tests. Test results and corresponding analyses are presented and discussed in detail.

Sep 8, 2021

By Benjamin Jennings, Jason Herron

In the summer of 2016 Xcel Energy experienced a storm event that resulted in the collapse of approximately 8.5 miles of a 345 KV transmission line near Rogers, Minnesota. In design of the new transmission line, Xcel Energy determined that ten tower locations would be replaced with steel H-frame structures supported by helical piles instead of wood H-frame structures supported by driven wooden piles. A steel foundation was proposed for the towers due to time constraints and site conditions unfavorable to large pile driving equipment. Xcel Energy contacted the helical pile manufacturer Hubbell Power Systems, Inc. (HPS) for aid in the design of a complete steel foundation for the structure legs. With the shear, moment, and axial loads provided, the manufacturer used pile group modeling and axial capacity software to design a four helical pile group; and used 3D modeling and finite element software to design a moment resistant grillage to connect to the tower base. The steel grillage utilizes a new moment resistant connection and clamp system to transfer loads from the piles to the grillage. This connection provides a true fixed head condition and reduces lateral deflection issues typical to smaller diameter piles in pinned head connections. The clamp is designed to deform the helical pipe pile shaft and transfer the full axial load of the structure through the mechanical and friction connection. The helical piles and the moment resistant grillage were manufactured with shorter than average lead times and a helical pile installation contractor performed the installation. An expedient plan of install was developed by the contractor that resulted in an average installation rate of one complete set of tower foundations per day. The design of the moment resistant grillage, clamping system, and excellent foundation construction by the contractor provided an expedient and efficient foundation system to be discussed in this paper.

Jan 1, 2017

By Louay Owaidat, Daniel Jabbour, Allan Frappier, Jose Gomez, Mark Stanley, Tino Maestas

The U.S. Army Corps of Engineers (USACE) is implementing a levee strengthening program along the Sacramento River East Levee (SREL) designed to correct 11 miles of deficient levees as identified by recent hydraulic and geotechnical investigations. The first project, the subject of this paper, completed in 2020 resulted in approximately 3.0 miles of improvements to the California Central Valley Flood Protection system. The project area lies along the east bank of the Sacramento River in Sacramento. The program consists of constructing cutoff walls through existing levee embankments to remediate levee through seepage and under-seepage. Key challenges included designing and constructing measures to remediate a 100-year-old legacy levee system, the presence of both industrial and residential properties immediately adjacent to the landside of the levee creating severe space and access limitations, and performing this work during the 2020 statewide mandate to shelter-in-place due to the COVID-19 pandemic. The project team of contractors, USACE, state and local agencies, and engineering firms partnered to bring this project to successful completion within budget and on schedule expending more than 60,000 man-hours with no lost time accidents. With the issuance of future planned contracts, the program will significantly reduce flood risk to the City of Sacramento.

Sep 8, 2021

By Kalyani Devabhaktuni, Mike Minton, Mark T. Howe, Yan Zhang

During the procurement phase of a Design-Build (DB) project, design-build contractors must often commit to a fixed price based on limited or incomplete geotechnical information. This lack of information can result in an inaccurate assessment and allocation of project risk to either the contracting authority or the DB contractor. This paper presents a case study of an elevated water tank supported by mixed ground improvement techniques, including Vibro-Compaction (VC), Aggregate Piers (AP) and Compaction Grouting (CG) in East St. Louis, Illinois. An adaptive design and contracting approach provided the best value solution for a complicated set of geotechnical problems, including static bearing capacity and settlement concerns as well as liquefaction induced settlement. Close cooperation between the owner, the tank contractor, the geotechnical engineer and the ground improvement contractor was essential to produce an effective solution. Ground Improvement techniques resolved the geotechnical challenges at the site through adaptive design methods, utilizing progressive rounds of verification and real time data acquisition to achieve performance objectives. This paper details the evaluation of geotechnical criteria, the selection of ground improvement techniques, the adaptive design and implementation of ground improvements, as well as contracting methodologies used to ensure that the best value was provided. PROJECT INFORMATION In November, 2016, CB&I Storage Tank Solutions (McDermott) submitted a design/build proposal for an elevated water tank for Illinois American Water Company (IAW) in East St. Louis, Illinois. The purpose of this tank was to have backup water capacity for power generation. In the RFP, IAW requested two alternate styles of tank: Option 1, a 1250 Million Gallon (MG) Composite Elevated Tank or Option 2, a 1250 MG Waterspheroid tank. Option 1 consisted of a steel tank supported on a concrete tower. Option 2 consisted of a steel tank supported on a steel shaft. The height (determined by IAW) was 140 feet to the top capacity line measured from top of floor slab.

Jan 1, 2019

By Sunil Arora, Lisheng Shao, Chris Conkle

"The East Garden Grove - Wintersburg Channel located in Orange County, California, required upgrades along the levees to mitigate potential liquefaction and lateral spreading hazards. The Orange County Public Works designed soilcrete columns constructed between two rows of steel sheet piles along both sides of the channel between Graham Street and Warner Avenue (approximately 2,500 ft), and along an approximately 2,000-ft-long stretch of the south levee. The earthen embankment, approximately 13- to 15-ft high and damaged significantly by erosion, was then excavated to widen the channel to increase the channel flood conveyance capacity.The site is located within the Los Angeles Basin, underlain by several thousand ft of marine sedimentary strata. Uncontrolled fill materials were encountered to approximately 10 ft below ground surface, underlain by tidal and flood plain deposits. Groundwater was encountered at sea level, which is approximately 10 ft below grade.This paper will discuss site soil conditions, and the construction and quality control of soilcrete columns constructed by wet soil mixing; also, the paper will introduce the Drilling Index (DI) as a measurement tool, similar to the cone penetration test (CPT), to evaluate the soil strength in more detail. Finally, the statistical analysis of soil mixing strength distributions for the project quality control will be presented.INTRODUCTIONWintersburg Channel in Orange County, California, required ground improvements along the existing levees to mitigate potential liquefaction and lateral spreading under the site design earthquake. Orange County Public Works designed and developed a cellular pattern of soilcrete columns sandwiched between two rows of steel sheet piles along both sides of the channel between Graham Street and Warner Avenue, and adjacent an approximately 2,000-ft-long stretch of the south levee (Fig. 1). An earthen embankment approximately 13 to 15 ft high, damaged significantly by erosion, was then excavated to widen the channel and increase the channel flood conveyance capacity.Stiff, soilcrete cellular wall structures can reduce the earthquake-induced cyclic shear stress ratio (CSR) in the soil within the cells, thus preventing excess pore water pressure build up which may trigger soil liquefaction. For this project, approximately 6,700 soilcrete columns were constructed in a cellular pattern to an approximate depth of 40 ft. All of the soilcrete columns are 3 ft in diameter with the design unconfined compressive strength (UCS) of 150 psi."

Jan 1, 2015

By Adam Zagorski, Rusty Lucido, Curt Scheyhing

"The current California Department of Transportation (Caltrans) practice based on AASHTO LRFD Bridge Design Specifications is to use the O’Neill and Reese method (FHWA, 1999) for calculating the side resistance and base resistance of Cast-in-Drilled-Hole (CIDH) piles / drilled shafts. In this calculation, end bearing is typically neglected for piles constructed using a wet method due to questionable reliability of end bearing resulting from soil disturbance and inadequate cleaning of the base. Pressure grouting below the tips of drilled shafts in cohesionless soils has long been used worldwide to provide reliable end bearing capacity, but for decades it was relatively unused in this country. It has been used increasingly in the United States over the last decade. Before this project tip grouting has not been utilized on or accepted by Caltrans to maximize piles end bearing capacity. This project proved that tip grouting to mobilize reliable base resistance can be successfully implemented on a full-scale bridge project requiring over 350 large diameter shafts.For the Gerald Desmond Bridge Replacement Project, Shimmick/FCC/Impregilo, JV utilized a temporary Oscillator casing to the full depth to install CIDH piles. Piles were constructed by the wet method and then pressure grouted below the pile tip. A tip grouting procedure for these large diameter shafts was developed and tested to specifically address the geology and constraints of the project. This procedure was then proven during the Load Testing of test piles during the Test Shaft construction phase of the project. Tests showed a minimum reliable base resistance of 150 ksf could be mobilized in very dense sand at a downward movement of 5% of the pile diameter for piles ranging from 4.9 to 8.2 feet in diameter. By tip grouting, the length and diameter of the piles were significantly reduced."

Jan 1, 2017

By Patrick J. Hannigan, Seth Robertson, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (―TLBT‖) and the conventional Bi-Directional Load Test (―BDLT‖) are full-scale static load test methods. In both methods, the test loads are applied bi-directionally to the deep foundation. The advantages of the conventional BDLT have been well established for cost efficient static load testing of deep foundations, particularly for large diameter, high-capacity drilled foundations. A conventional BDLT applies the bi-directional test loads using an embedded jack and bearing plates. The TLBT method also applies the bi-directional test load to embedded bearing plates but does so using reusable high-strength threaded bars attached to an above-grade hydraulic jack and load transfer assembly. The new TLBT method is well suited for load testing shafts of a moderate diameter, length, and nominal resistance or ultimate load. TLBT advantages include economic considerations resulting from the method’s reusable load application components and constructability considerations as it readily accommodates a center concrete tremie pipe or pump line location. This paper presents comparison results from full-scale load tests performed using both bi-directional load testing methods. Adjacent 3-foot diameter by 30-foot long BDLT and TLBT shafts were tested. Details regarding subsurface conditions and test shaft construction are included for the comparison of the TLBT and BDLT results. Corresponding test data and analyses for both test shafts are presented and discussed in detail. The BDLT shaft had a maximum uni-directional load of 240 kips at upper and lower bearing plate displacements of 0.5 and -3.8 inches, respectively. The TLBT had a maximum uni-directional load of 300 kips at upper and lower bearing plate displacements of 1.0 and -5.9 inches, respectively. These results as well as the load-transfer behavior and equivalent top loading curve results from the adjacent BDLT and TLBT drilled shafts are discussed. The paper also discusses the strain gage instrumentation on the TLBT load application bars and on the embedded bearing plates.

Oct 1, 2022

By Rick Deschamps

"Fountain Slide is located approximately 10 mi (16 km) northeast of Lillooet, British Columbia, Canada, within the Coastal Mountain Range, and has been locally active since the 1970s. The project site is located near the base of the relic Tunnel Mountain landslide. The progressive movements have posed a significant challenge to British Columbia (BC) 99, the main north-south highway in the region. The slide began affecting the British Columbia Railway Company (BCR) tracks in the 1990s. In 2004, the Canadian National Railway Company (CN) acquired BCR and, during the next 11 years, undertook measures to stabilize the rail bed. Some of the measures undertaken include numerous track realignments, a shotcrete and soil nail wall, an anchored soldier pile-and-lagging wall, and adding a row of anchors to the wall. For many years, the measures had proved successful until mid-2014 when it was observed that the slide retrogressed uphill of the tracks. Since that time, the slide movements typically ranged between 5/32 and 0.4 in (4 and 10 mm) per day, leading to extreme distortion of the earth retention system and the need for frequent track realignment.In the spring of 2016, CN issued a request for proposals (RFP) for a designbuild solution with the expectations of: (1) a safety factor greater than 1.2, (2) considering only the currently identified retrogressive blocks that extend to about 200 ft (61 m) above the track; and (3) minimizing activities outside the current easement. It was also communicated that there was a possibility that a portion of the line may have to be abandoned if the proposed remediation was cost prohibitive.The fact that the existing slide was a small fraction of the relic slide was intimidating. The relic slide extended for approximately 1.0 mi (1.6 km) above the uppermost retrogressive block that was now affecting the rail line. Other areas of concern included:"

Jan 1, 2017

By Brandon T. Buschmeier, Sonia S. Swift, Michael P. Walker, Frederic Masse

"Ground improvement has undoubtedly become a cost-efficient and effective solution to support the development of poor soil sites. Ground improvement elements, such as Controlled Modulus Columns (CMCs), replace piles by improving the subsurface soils and reducing settlement. As ground improvement becomes more popular, the applications become more creative and ground improvement is being used to control settlements under large structures with tight settlement tolerances.In this paper, we will discuss the use of CMCs to support two (2) large industrial warehouses where soil conditions would normally lead to the use of deep foundations and a structural slab, grade beams, and hung utilities to prevent excess settlement. Each of the sites we will discuss had poor soil conditions in the form of very soft or compressible soil, heterogeneous fill of varying thickness, and environmental contamination. At each site, we developed a design that would allow for the use of Controlled Modulus Columns (CMCs) with a Load Transfer Platform (LTP) in place of the previously-proposed deep foundations. The use of the CMCs also allowed for the use of spread footings and slab on grade construction. The benefits of this value-engineering approach include economy in the foundation system, risk mitigation by not disturbing contaminated soils requiring expensive removal, and ease of access for future sub-slab upgrades with new tenants. Additionally, the use of recycled concrete aggregate as an LTP is more environmentally friendly than placing structural slabs with heavy steel reinforcement.Designing for the settlement of large warehouses is challenging because it requires changing how we typically perform our designs. For most structures, the slab loads are relatively light when compared to the footing loads, whereas for warehouses, the slab is heavily loaded compared to the relatively light footing loads. Thus, it becomes essential to perform three-dimensional analyses to confirm that the proposed CMC layout will provide uniform support of the slab and footing across a variety of loading scenarios (loaded bays vs unloaded or travel bays). The complexity of the designs for these warehouses generated interest in conducting large area load tests over a grid of multiple columns. The performance of the area load tests provided invaluable information on the effectiveness of the LTP and CMC spacing. In this paper, we present a general description of CMC ground improvement, the differences between ground improvement and traditional pile foundations, our typical design methodology for CMC design, and the modifications to that methodology for warehouses."

Jan 1, 2017

By Steven E. Darnell, William W. Haasz, Brandon T. Buschmeier, Frederic Masse

"Landfills often cover expansive areas in locations where large building facilities or infrastructure is in high in demand after the land has been reclaimed. Most landfills have soil or fill properties that vary widely over small distances; combined with the strict guidelines and restrictions for the removal and treatment of soil or material that is on site, these projects can be a major challenge for any prospective developer. In order to make landfills suitable for the construction of any project it is necessary to conduct a detailed evaluation of the subsurface conditions. Ground improvement techniques are among the most typical methods for making reclaimed landfills suitable for the construction of any major project. The paper will discuss the approach that was taken to support a proposed warehouse in Elizabeth, New Jersey using Controlled Modulus Columns Rigid Inclusions (CMC Rigid Inclusions), which are grouted, auger-displacement elements. Additionally, we will discuss the use of Dynamic Compaction (DC) that was performed in areas outside the proposed warehouse footprint. Through the combination of CMC rigid inclusions and DC, the general contractor’s project schedule was expedited, the costs to support the warehouse were economized, and the anticipated settlement of the parking lot areas was drastically reduced. Furthermore, the paper will outline the benefits of using CMC rigid inclusions and DC methods in order to minimize the impact of working with contaminated soils from a landfill.OVERVIEW OF THE ELIZABETH WAREHOUSE PROJECTOver the past several decades the foundations industry has seen an increase in demand for the support of developments on reclaimed landfills; particularly, on the east coast where many landfills were capped before the 1980’s and steady population growth and city expansion have caused high demand for this now highly desired real estate. Unfortunately, these landfills, often as large as twenty (20) or more acres present tough geotechnical and environmental challenges for Owners planning to develop or build structures of any size on the reclaimed land. Consequently, the options for building on reclaimed landfills can quickly become cost prohibitive.Site SpecificSelected by a developer for the location of a future warehouse, the 29 acres (114,424 sq-meters) project site is located in Elizabeth, New Jersey and demonstrates the complexities of designing over a once reclaimed landfill. The landfill was used for municipal solid waste (MSW) consisting of trash, wood, metal, glass, plastic, brick, concrete fragments, and other types of debris. This landfill was capped in the 1960’s, and developed in the 1970’s for a warehouse. The new project included the demolition of the existing warehouse and the development of the site to be repurposed for a new 481,650 sq-ft single-story warehouse, surrounded by paved parking and truck loading areas. Figure 1 below, shows an overview of the project site layout."

Jan 1, 2017

By Kirk Ellison, Eric S. Lindquist, Peter Faust, Stephen M. McLandrich

"The 181 Fremont Tower will be an 800-foot high-rise with a 60-foot deep basement located in a dense urban part of downtown San Francisco. The design and construction methods of the subsurface elements navigated a variety of site constraints such as loose fill and soft estuarine soils, shallow groundwater, contaminants, historic obstructions, small work area, proximity of adjacent buildings, and the on-going excavation and build-out of the adjacent Transbay Transit Center (TTC) train box. Design of the approximately 260-foot-deep drilled shafts (some of the deepest foundations ever constructed in San Francisco) was proven by a full-scale load test that provided unique data on the frictional capacity of the deep soil and Franciscan Complex bedrock in the region. Design and construction of the shoring system for the 5-story basement excavation was exceptionally challenging because of the on-going construction for the TTC. To allow for flexibility during construction, hydraulic rams were placed in a transfer waler along the shared TTC shoring wall that could adjust the forces transferred through to the TTC excavation if required. Open and steady communication between the shoring engineer, the geotechnical engineer, and the shoring/foundation contractor was crucial in order to satisfy the complex constraints of this site.INTRODUCTIONThe 181 Fremont Tower is a new build mixed-use tower, currently under construction in the dense urban core of the South of Market District of San Francisco, California. This high-rise will consist of 54 above ground floors with the roof level 700 feet high. Atop the roof will be some architectural features including a spire that will top out at just over 800 feet, which will make it the second tallest building in San Francisco upon completion.The tower is being developed by Jay Paul Company and the architectural design is by Heller Manus. The structural engineer and geotechnical engineer for the project is Arup North America Ltd (Arup). The shoring designer is Brierley Associates (Brierley). The general contractor is Level 10 Construction (Level 10) and the specialty foundation contractor and excavation contractor is Malcolm Drilling Co., Inc (Malcolm)."

Jan 1, 2017

By Eric P. Bregman, Justin Zarrella, Ryan M. Coulson, Connor Johnson

Within a prominent Boston, MA suburb are a pair of historic stone and mortar structures built in the late 1800’s. Both the Main House and Carriage House have been maintained and occupied throughout their rich history, but renovations were needed to address structural concerns and building code compliance issues. The focus of this paper is to detail an innovative underpinning design that addressed ongoing settlement issues at the Carriage House. GZA GeoEnvironmental, Inc. (GZA) partnered with Phoenix Foundation Company, Inc. (Phoenix) to design foundation wall support systems for Consigli Construction Company (Consigli) that would effectively underpin the historic field stone foundations. Originally, conventional concrete pit underpinning and jet grouting were contemplated as methods for support. However, due to the age and condition of the existing foundations, worker safety concerns, and the risk of additional structural damage, GZA/Phoenix elected to pursue a less traditional approach. The alternate design consisted of micropiles used for combined temporary and permanent foundation support. The load transfer system included steel headers with needle beams cored through the field stone foundation walls and reinforced concrete grade beams/pile caps. To validate design performance and ensure worker safety, GZA installed a fully automated survey monitoring system to record lateral and vertical building deformations. This included real-time email alert notifications to inform the Project Team of any threshold exceedances. From the start of micropile drilling through full load transfer to the temporary support and permanent foundation systems, the underpinning performed as designed resulting in less than 3/16-inch of vertical and horizontal deformations observed. This magnitude of movement is less than half of what is generally accepted deformation tolerances for masonry structures and considered exceptional performance. The focus of this paper is to provide additional details on the unique design, sequencing, installation, and performance of the underpinning systems.

Sep 8, 2021

By Masakazu Takano, Koji Suzuki, Naotoshi Shinkawa

"Cement deep mixing (CDM) method successfully applied to a marine construction project in northern Vietnam is reported. The method is classified as wet method, in which cement slurry is injected into the ground. Thickness of clayey deposit subjected to improvement is from 20 m to 28 m, and the total volume of CDM improvement exceeds 460,000 m3. This is the first massive application of CDM method in the region. Three CDM barges, each equipped with four mixing shafts, were brought to the site in order to finish CDM work within a period of seven months. Cement content used in the work was 180 kg/m3 and water-cement ratio of slurry was 100%. Unconfined compression strength of stabilized soil was 1,200 kPa to 1,600 kPa in average with coefficient of variation from 0.3 to 0.4. Statistics analysis of the strength with these values gave percentage of lower strength less than 10%. Trial use of needle penetration test performed to study strength profile of a CDM column is also reported.INTRODUCTIONThe site of Lack Huyen Port Infrastructure Construction Project is located in the sea adjacent to Cat Hai Island, offshore Hai Phong city which is around 100 km east of Hanoi, the capital of Vietnam. Left side of Fig. 1 shows the location of the site. The project contains development of container terminal, dredging of waterway, construction of sand protection dyke to prevent waterway from being buried, and bridge construction to connect the island to the mainland.Joint venture of Penta Ocean Construction and Toa Corporation was awarded Package 6 of the project, in which reclamation of container terminal area, retaining wall construction and terminal road construction were included. Plan of the site is presented in right side of Fig. 1. The site work has been started in June 2013 and is scheduled to finish within 4 years."

Jan 1, 2015

By Mohamed A. Eliwah

This paper deals with the determination of hydraulic conductivity of the coastal coralline limestone aquifer of Jeddah, Saudi Arabia. This coastal area has witnessed urban development and establishment of towers which requires deep foundations, excavation and dewatering of huge quantities of unconfined groundwater. It is occupied with successive layers of soft detrital and consolidated massive cavernous coralline limestone of the Quaternary age. These layers are encountered at a depth of 1.5m and extend for more than 100m. Hydraulic conductivity values were obtained by analyzing the pumping tests data under steady and transient state conditions. Hydraulic conductivity values help in selecting the proper and safe dewatering system, as well as determination of discharge rates and quantities of groundwater to be withdrawn. Test results obtained from two surveyed sites showed that the values of hydraulic conductivity are greatly variable. It ranges between 118.1 and 1559.6 m/day at the first site, whereas at the second one it ranges between 94.6 and 350 m/day. These high values are attributed to the cavernous nature of the water-bearing formation. Jeddah city could be divided into three different dewatering zones extending from north to south parallel to the coast line. Well point dewatering system could be applied in the first zone while ditches and sumps are the most suitable dewatering method in the second and third zones. Dewatering using deep wells in such highly permeable formation will require withdrawal of huge quantities of water which will be accompanied by washing out fine sediment filling the cavities in the surrounding areas. This will badly affect the nearby buildings through settlement, crakes and other structural damages. Therefore, construction of grouting plug/blanket with thickness of 3.0 m at a depth of 20.0 m is recommended. This depth will be enough to support the plug against the hydrostatic pressure. Moreover, it is highly recommended to transfer the site into closed box, by using diaphragm walls or secant bored piles.