Search Documents

By R. Druffel, P. Wittke-Gattermann, M. Wittke

"The two tubes of tunnel Hirschhagen along the highway A44 in Germany, underpass the federal road B7, a railway line and the valley of the river Losse close to the city of Hessisch Lichtenau. The ground in the area consists of Triassic sand- and siltstones (""Buntsandstein"") as well as tertiary clays. Prior to tunneling, the groundwater in the area is planned to be lowered by means of a gallery of deep wells. As a basis for the design of this dewatering gallery, two large pumping tests have been carried out. The results of these tests have been evaluated by means of 3D-Finite Element analyses. By means of the large-scale model, the influence of the anisotropy resulting from jointing and bedding and the influence of fault zones in the area have been taken into account, which lead to a thorough basis for the design of the dewatering gallery.INTRODUCTIONThe 4.2 km long Tunnel Hirschhagen of the highway A 44 crosses below the federal road B7, a railway line and the river Losse close to the city of Hessisch-Lichtenau in central Germany. Both tunnel tubes are located in a subrosion depression in which Triassic sandstone and tertiary clay prevail. It is planned to lower the groundwater table in the area of the meadow of the Losse prior to tunnel heading [1]. Groundwater lowering is planned to be achieved by means of a series of large pumping wells. The bottom of the river Losse will be sealed in order to avoid direct inflow of water from the river into the ground (Fig. 1 and 2)."

Jan 1, 2015

By A. Bezama

For over a decade European countries have addressed contaminated sites by developing technologies for managing both polluted soil and groundwater. This development has not only been driven by health and environmental aspects, but also because of economic pressures, as the remediation and redevelopment of derelict areas can be a meaningful alternative to undeveloped areas for the establishment of new industrial, recreational, housing and service locations. In most developing countries, however, the subject of contaminated sites is a new environmental issue that authorities have recently started to deal with. Among these countries, Chile has just started to prepare the country's legal context as well as to foster the formation of research and investigation groups that will deal with the exploration, investigation and management of contaminated sites. That requires a comprehensive technical, scientific and legal support in this stage. Goal of this article is to present the state-of-the-art technologies for site remediation currently applied in industrialized countries, in order to identify the most interesting approaches that can be implemented within the Chilean situation, especially considering the influence of the copper mining industry on the soil and groundwater quality of the environment surrounding their production facilities.

Jan 1, 2007

By A. C. Gagnon, H. Saroglou

"The focus of this paper is on the analysis of geometrical discontinuity properties for the rock mass located within an open pit mine located in Western Africa. Discontinuity data were collected using various techniques including oriented core logging, borehole televiewer surveys, surface pit wall mapping and photogrammetry. The geological setting was initially studied prior to the data analysis to produce threedimensional ground models of the regional and mine site geology along with block diagrams illustrating predicted fracture patterns. Stereographic and statistical discontinuity data analysis of the geometrical properties of the rock mass was subsequently performed to identify unique structural domains throughout the open pit area. The discontinuity data collected throughout the studied open pit area were primarily discontinuity orientation, frequency and spacing and the investigation focused on the reasons for observed differences between the various data collection techniques. Stereographic analysis was used to assess the preferred geometry of discontinuities filtered by lithology, data collection technique, borehole, discontinuity type and pit wall (footwall or hanging wall). The observed fracture pattern is explained adequately by the geological setting. The need for accurate ground models for the design of open pit slopes is highlighted.INTRODUCTIONThe Tasiast Mine is an open pit operation located in north-western Mauritania, approximately 300 kilometres north of the capital Nouakchott. The Tasiast mine, which is owned and operated by Kinross Gold Corporation (Kinross), began commercial operations in 2008. The Tasiast mine is located in an area characterized by flat desert terrain within the western reaches of the Sahara Desert region. The current mine site includes mill buildings, shop facilities, waste dumps, tailings facilities and two main open pit operations (Piment and West Branch). The West Branch pit is the focus of this paper. The current open pit plan for West Branch indicates a final pit measuring approximately 2.5 km long by 1.4 km wide and 510 m deep."

Jan 1, 2015

"Discrete Fracture Network (DFN) modelling has increasingly being used in many geotechnical and mining engineering problems, the authors believe there is an ever greater demand to provide updated guidelines that address the collection of discontinuity data in the specific context of DFN models. In general terms, the generation of a DFN model requires collecting information on i) fracture orientation, ii) fracture intensity, iii) fracture length and iv) fracture terminations. The International Society of Rock Mechanics (ISRM) suggested methods for the quantitative description of discontinuities in rock masses directly include most of these parameters. However, there are important differences engineers should be aware. To what extent discontinuities can be sampled and which limitations are inherently introduced in the analysis by the sampling methods being adopted represent important aspects that should drive the collection of discontinuity data for DFN analysis; this will require the introduction of a more appropriate set of guidelines bridging the gap between the current, very practical, ISRM methods and the data requirements imposed by the use of new DFN technologies.INTRODUCTIONThe last decade has seen a major increase in use of the Discrete Fracture Network (DFN) approach, both as a stand-alone tool or integrated within more complex geomechanical simulations (Rogers et al., 2014 and Elmo et al., 2014). In particular, the DFN approach offers the opportunity to maximise the use of fracture data collected from mapping of rock exposures and to construct synthetic rock mass (SRM) models. However, the potential of DFN based modelling is limited if there is insufficient care in collecting the necessary structural data at the required engineering scale. DFN models are also subject to the process of data calibration and validation (Hadjigeorgiou, 2012). With DFN modelling becoming an almost integral part of many geotechnical and mining engineering problems, the authors believe there is an ever greater demand to review the process of collecting fracture data in the specific context of DFN modelling.The value of the DFN model depends directly on the quality and quantity of available field data. For example, fracture length (persistence) is an important parameter in DFN modelling; however, this parameter is either seldom available at the pre-feasibility stage due to a lack of exposures (man-made or natural), or engineers have access to limited length data collected along exploratory drifts. Characterisation of rock exposures should also take into account limits of window/scanline mapping techniques with respect to both trace length bias and the effect of cut-off assumptions inherent in the mapping methodology."

Jan 1, 2015

By Joël P. T. Kapusta

Back in 1995, Air Liquide and Union Minière presented a joint paper at the Copper 95 – Cobre 95 Conference in Santiago, Chile, describing the first full scale plant trials of shrouded sonic injection in a Hoboken converter at the Hoboken smelter in Belgium. Almost a quarter of a century later, the technology known as ALSI, or Air Liquide Shrouded Injection, has been tested or commercially implemented in several copper and nickel smelters. Despite these successes, the copper industry did not adopt it widely in the same manner the steel industry adopted the Savard-Lee tuyere in the 1970s and beyond, not even in the way the lead industry adopted it with the Queneau-Schuhmann-Lurgi, or QSL, process. The development and implementation of bottom-blowing smelting and converting technologies in China in the last ten years, however, changed the industry’s perception that high- and ultra-high oxygen injection in copper smelting and converting was indeed possible under specific process conditions. In this paper, I retrace the key learnings of my journey with sonic injection over the twenty five years from my humble beginnings in my early years with Air Liquide, through plant trials and technology implementation in the late 1990s and into the first decade of the new millennium, and ultimately, to the most conclusive proof that the sonic injection design methodology I established is valid, and the calculation tools I developed are accurate. I conclude by sharing my thoughts about whether the deployment of the Savard and Lee legacy within the nonferrous industry was just a pipe dream or whether it will become a reality. INTRODUCTION In the context of lower quality ores and changing economic markets, copper smelters need to continuously innovate and improve to remain competitive and respect their corporate social responsibility engagements. One avenue towards this business, social, and environmental goal is to increase process intensity while lowering fossil fuel consumption to lower greenhouse gas emissions and reducing process off-gas volumes to better capture As and SO2–laden emissions. I believe high oxygen sonic injection for submerged tuyere copper bath smelting and converting is one technology that can help smelters achieve that goal of higher business, social, and environmental performance. Twenty five years ago, when I discovered that the Savard-Lee tuyere had revolutionized the steel industry (Savard & Lee, 1966; Knuppel, Brotzmann, Fassbieder, Savard, & Lee, 1972), I had a dream — or was it a vision? — that within the first decade of the new millennium, modern copper smelters operating submerged tuyere bath smelting and converting vessels will have implemented high oxygen sonic injection and will be reaping the financial and environmental benefits that the steel industry enjoyed in the 1970s. As we approach the end of the second decade of the new millennium, I have to admit that my dream has been all but shattered as the majority of copper bath smelting and converting vessels today continue to operate under bubbling regime conditions. This mode of operation is archaic, still requires tuyere punching and blows at inherently low enrichment levels, particularly in converting, producing large volumes of process off-gases. Under such operating conditions, regulations and emission quotas for As, SO2, and particulate matter oblige smelters to use not just primary or secondary hoods, but sometimes even tertiary hoods. I vividly recall being told, fifteen or twenty years ago when visiting smelters to promote the application of the Savard-Lee tuyere in nonferrous processes, that implementing sonic injection was not economically viable due to the high cost of compressing air and oxygen. Some of the smelters I visited back then have since mandated their engineering partners to design and build secondary or even tertiary hoods. I cannot fathom how secondary and particularly tertiary hoods, with all of their auxiliary equipment and added ducting, could be more economically viable than purchasing and installing a few compressors, expanding the pipeline network for compressed air and oxygen, and installing a new control valve train to feed sonic tuyeres. Besides, adding hoods does not address the problem of As and SO2-laden fugitive emissions at its source but merely provides a costly mitigation for it by capturing larger volumes of process off-gases rather than reducing these large volumes in the first place. Moreover, hooding does not reduce energy consumption nor does it increase process intensity, two aspects that I believe are critical for smelters to remain competitive and sustainable in a deeply changing market environment.

Jan 1, 2019

Toronto 2013 Proceedings

May 1, 2013

What Discounted Cash Flow Analysis can do for you: ?Provide an accurate financial analysis of a project for the first 25 to 30 years of operations ?Identify cash flow requirements ?Identify relative sensitivity of the project to the various input parameters ?Place a value on the resource in place after 30 years of operations ?Correct for errors in input parameters

May 1, 2010

By B. D. Wood, J. A. Fowler, H. S. Grütter, J. M. Kong

Abstract- The phased approach used by De Beers for diamond exploration is briefly outlined. The Victor kimberlite is one of 19 kimberlites in a cluster near Attawapiskat, Ontario. The progress at the Victor kimberlite is summarized, and the operations are described within the framework of this staged approach. An evaluation program is currently under way on the Victor kimberlite, but although results are encouraging, insufficient diamonds have been recovered to permit disclosure of estimates for the grade and value.

Jan 1, 2001

By David Green

"This paper describes Outokumpu's Tank Cell concept using the unit reactor principle and operating experience gained in various applications. Presently the tank cells used range in size from 35 t pilot size to 100 m' (3500 cuft). The paper discusses operating experience and results from commercial installations in copper and zinc rougher and cleaner services.The key feature of the Tank Cell described is the effective control of the froth phase and resulting possibility to operate on an improved grade recovery curve by manipulating the control variables."

Jan 1, 1995

By V. Evans

Mine lateral development advance rates currently average about 5 metres (16.5 ft.) per day. Granduc Tunnel hit 35.1 metres (115 ft.) on their best day, 12 km from the portal, single heading forty-three years ago. This Canadian mining record remains an excellent example of rapid drill and blast excavation with suggestions for improving current practice.

May 1, 2011

By Don Ritz

Smart leaders focus on safety even in tough times. Businesses that retreat into survival mode and ignore safety do so at their peril, risking loss of employee and stakeholder confidence and exposing themselves to financial and reputational loss they can ill afford. It?s a moment of truth when employees and stakeholders learn whether safety is truly your priority or just a convenient cliché for good times. Visionary leaders who build safety culture even in a downturn maintain people?s trust, prevent loss, and position the organization for enhanced success as times improve. Safety is the right business focus in good times and bad.

May 1, 2009

By Normand Bédard

This presentation highlights Cambior?s initial approach for recruiting and retaining its international employees, the importance of proper preparation and the support needed to ensure a competent and stable workforce. In general, most of the training and information available for human resources personnel prepares the specialist for handling various aspects of labour relations, recruitment and hiring, benefits administration, employee relocation, etc. This is usually done in a Canadian context. Only recently, has more specialized training been developed to prepare human resources practitioners for the complex issues related to expatriate employees and dealing with human resources issues in other countries.

May 1, 2003

By M. Uszko

Methane drainage and ventilation methods of methane hazard mitigation are used in the coal mines of Kompania Weglowa S.A. Over 22% of methane released during mining activities is captured by methane drainage systems and transported to the surface. In this article we present development plans for utilization of methane captured and transported to the surface by methane drainage systems. The results of research on the possibility of economic utilization of methane concentrated in ventilation air that leaves the mine through fan diffusers are also described.

Aug 1, 2013

By Renaud Cousin

Supported gold catalysts were prepared by Direct Anionic Exchange on an alumina support and tested during the reaction of CO oxidation and of saturated and unsaturated hydrocarbons (C1 to C3). The catalysts showed high activies over a range of concentrations and temperatures compatible with an application to automotive exhaust cleaning. Furthermore, a complete resistance to thermal ageing at 600°C in the absence or presence of water was observed due to the obtention of strongly anchored nanosized gold particles during the preparation step.

Oct 1, 2003

Abstract - A method to extract certain types of error variance information from paired data is presented, which constitutes an important tool for the calibration of Gy’s formula for variance predictions in the sampling of broken ores. The research summarized here complements publications by others on geochemical precision. The model and method proposed for treating duplicate data provide a practical means of deriving separate estimates of the purely analytical and aliquot sampling variances, from a unique set of duplicate assays, and, hence, proposes a new avenue for estimating effective mineral grain size.

Jan 1, 1998

By George Hope, Dave Green, Jacques McMullen

The Est Malartic mill has been treating massive sulphide, copper/gold ore from the Bousquet 2 mine since 1989. The need to minimize copper content in flotation tails which are leached for gold recovery and to produce a saleable copper concentrate led to the evaluation of Conventional, Column and HG flotation methods. The HG method was preferred and two full-scale cells were installed and operated over a two-year span. In 1992, it was decided to expand the mill capacity from 1500 tpd to 2500 tpd. A total of nine additional HG Tank Cells were installed to provide additional roughing and cleaning capacity. The expanded plant has been operating since June 1993.

Jan 1, 1994

By M. McKim

"Due to the fact that there were no formal papers submitted for this session we can only print the discussions of the papers. a) Maqnetic Mill Liners : M. MckimE. MarcotteFalconbridge LimitedReplyIn looking at the slides on magnetic mill liners a question comes to mind, particularly in the case of a large diameter mill using large grinding media, concerning the potential hazzards which may exist from large chuncks of steel hanging in the mill. Would you comment.The magnetism was sufficiently strong from liner to liner to hold ........................ .(We are sorry but we could not transcribe the full reply to this question as no microphone was used by the speaker and i't was impossible for us to complete the rest).·"

Jan 1, 1984

By Shamil Shaikhutdinov

CO adsorption on gold particles deposited on well-ordered alumina and various iron oxide films has been studied with temperature programmed desorption (TPD) and infrared reflection adsorption spectroscopy (IRAS). Structural characterization has been performed with scanning tunneling microscopy. Data show that the CO adsorption exhibits a size effect in that small particles adsorb CO more strongly. The effect generally vanishes after annealing to 500 K. For annealed samples, CO TPD and IRAS spectra are nearly independent of the particle size and supports studied. The results indicate that the CO interaction with gold surfaces is essentially similar and involves low coordinated atoms.

Oct 1, 2003

By Tracy-Lynn Humby

A recent report commissioned by the South African Chamber of Mines, Mining Vision 2030, identifies the South African mining industry?s negative legacy, its exploitation of people and the environment, as the single biggest hurdle to maximizing the industry?s impact on national development. Industry leaders have identified the need to put the past ?to rest?. With reference to three recent cases involving members of the South African mining industry, this paper points to the continuities between the past and present. It argues that the metaphor of ?multiple crossings? is more generative than the notion of putting the past ?to rest? for purposes of engaging with mining?s negative legacy.

Aug 1, 2013

The AG/SAG circuit discharge P80 is now increasingly referred to as the “Transfer Size” or T80 for short. From the literature it is apparent that in circuit design some approaches to the sizing of AG/SAG mills as well as the ball mills that they feed use this parameter. This paper reviews whether the use of the T80 is appropriate in this context. In the course of the review examples of AG/SAG discharge size distributions measured from range of operating circuits are used to illustrate the arguments made.

Jan 1, 2012