Search Documents

By Renato Macciotta

The argillaceous formation known as the Opalinus Clay is host to the Mont Terri Underground Research Laboratory. The URL was developed to investigate the hydrogeological, geochemical and geotechnical properties of the formation. Underground excavations at the site are characterized by non-elastic and time-dependent deformations. Excavations trending perpendicular to the strike of the bedding presented relatively minor deformations, however, tunnels parallel to the strike of the bedding showed much larger non-elastic deformations. This paper presents an analysis of the measured response of a tunnel trending parallel to the strike of the bedding in Opalinus Clay. The measured convergence is compared to tunnel experience in weak rocks to assess the tunnel stability.

Jun 1, 2012

By Michael L. Wayman

Native copper is copper which exists in nature in elemental, metallic form, rather than being chemically combined as is the case with the more usual oxides, sulphides, carbonates, etc. Several other metals, including gold, silver and platinum also occur in native form as do, rarely, iron, lead and mercury; a few naturally occurring native metal alloys, notably electrum (gold-silver) and tumbaga {gold-copper or gold-silver-copper) are also known. An analysis of the relative availabilities of native metals as nuggets in a useful size range111 shows native copper to be by far the most abundant of the native metals, exceeding both gold and silver by at least two orders of magnitude. While such an estimate is crude, it serves to illustrate why copper was one of the first metals to have been used by ancient peoples. Native copper is known to occur on all inhabited continents, although its exact occurrence and abundance in ancient times cannot be unambiguously determined because many surface deposits may have been totally exploited and are therefore no longer identifiable. It is clear, however, that native copper does or did occur in all areas inhabited by the early metal-using cultures, for example in the Andes, in Central America and in the Near East. It is remarkable that most of the world's native copper occurs in the deposits of the Lake Superior region, primarily on the Keweenaw Peninsula of northern Michigan and on Isle Royale, an island in Lake Superior some 50 miles north of the Keweenaw deposits. Canadian deposits of native copper are found in Newfoundland and Labrador, Nova Scotia, Quebec, Ontario, British Columbia, the Yukon and the Northwest Territories (on Victoria Island, Bathurst Inlet and the Coppermine River area). It was to locate the latter deposits that the explorer Samuel Hearne was sent overland from Hudson's Bay in 1770; they were also surveyed by Sir John Franklin's expeditions in the 1820s.

Jan 1, 1999

By S. A. Willis

For the past several months 1 have been considering the functions of this Society and its reasons for continuance. The fact that it is now sixty years old indicates that it must have been of value and we all know that it has contributed much that was worthwhile to Nova Scotia and the Maritime Provinces. The question arises: "What is the future of the Society, and how might its activities be altered to suit present-day activities and to be of even greater value?" Let us analyse the various activities in which we are interested and determine which, if any, are of more value than others. First of all, at least once a year we have a two-day convention which constitutes a holiday for the members and their wives. This has always been well planned and has been much enjoyed. Second, there are many social and business contacts made during the meetings and interim meetings. These certainly tend toward better relations and co-operation between the various people concerned. Mine operators meet other mine operators, engineers, people from the education fields, Department of Mines, and so forth. Various sales contacts are made at these meetings which can be of value and use to both the Company selling and the customer. Third, and of greatest importance in any conference, is the exchange of ideas by the members and by authorities from outside, and the presentation of slides and drawings, or actual visits to operations. It is upon this phase that 1 wish to elaborate. These papers are not only presented to our meetings but are generally published in the C.I.M. Bulletin so that members throughout the Dominion have access to them. Many important papers describing new phases of operations have originated through our Society.

Jan 1, 1947

By E. Stansfield

Coal samples are sometimes taken from a wet spot in a mine, or from an open car or pile shortly after rain, and submitted for analysis in a dripping wet condition. Other samples are taken from a dry spot in the mine, or from an open car or pile after a period of dry weather. Comparison of the analyses obtained in the two cases would be absurd, although the samples might be of essentially the same coat apart from the surface moisture on the one. The analyst therefore attempts to reduce all samples to an equal basis by the operation known as air-drying. Air-drying is practised by the chemist for three reasons: (1) To make it possible to grind the coal to powder. (2) To bring the coal sample to a condition in which it will not change in weight rapidly whilst portions are being weighed out for analysis -in other words, to bring it into equilibrium with the air in the laboratory. (3) To determine the water-retaining power of the coal. Any kind of drying is satisfactory for (1); the coal should be dried more or less according to the humidity at the time in the laboratory for (2); whilst it should be always dried to the same extent for (3). In other words, no method can be satisfactory for both (2) and (3). In this paper the only question considered is (3) -that is, air-drying the coal under standard conditions so that strictly comparable results can be obtained for the water content of coals after air-drying. After a sample of wet coal is exposed, it loses moisture until it is in equilibrium with the air at the time: thus the coal will loose distinctly more water in air of 20 per cent relative humidity, for example, than it would in air of 80 per cent.

Jan 1, 1923

By B. E. Shaw

This paper describes the use of the Free Piston Valve, and a simple hoist brake control system, which has been developed over the last two years, greatly improving the performance of low-pressure brake engines. The basic control system is outlined, with sections devoted to emergency trips and differential braking, and the application of the system to deep shaft hoisting is discussed.

Jan 1, 1966

By John F. Kearney

Labrador Iron Mines (?LIM?) Schefferville Projects consist of 20 major DSO deposits lying along a 120 km strike length in both the provinces of Newfoundland and Labrador and in Quebec. The town of Schefferville, Quebec lies close to the middle of this 120 km strike. LIM?s various properties comprise twenty different iron ore deposits which were part of the original Iron Ore Company of Canada (?IOC?) direct shipping Schefferville operations conducted from 1954 to 1982 and formed part of the 250 million tons of historical reserves and resources previously identified by IOC. LIM intends to develop all these resources in five separate stages. The first four stages will see the various deposits treated in three beneficiation plants, to be built adjacent to several of the deposits that comprise the Central, South Central and North Central Zones. The final stage is not yet planned but will likely involve a fourth plant. A Feasibility Study has not been completed on any of these Projects. LIM plans the development and mining of the various deposits in separate Stages. It should be noted that only the James and Redmond deposits have been permitted. All other deposits require environmental assessment and permitting. Only the James and Redmond deposits have been subject to detailed mine design. The Houston deposit has had preliminary mine design carried out. All other deposits will require detailed mine design when further geological data is collected and compiled. Detailed metallurgical testwork has been carried out on blue ore from James, Houston, Redmond and Knob deposits and to a more limited extent on yellow and red ores from these deposits. Only limited review work has been carried out on the high-silica blue ores. All of this work will be needed to be complete to confirm the final process routes. Additionally some metallurgical work will be required to be conducted on each of the other deposits to characterize their metallurgical response and to confirm expected recovery levels. Detailed mine design and metallurgical testwork has been carried out on those deposits that will form the basis of production for the initial years but further exploration, testwork and design is required for all the remaining resources. The first plant at Silver Yards and mine construction at James are now complete and initial production is expected in the spring of 2011. Metallurgical testing of the first stage deposits has established that the ore can be successfully upgraded to marketable standards. Based on the current testwork, a program of plant enhancement on the Silver Yards plant is now planned with the objective to increase both the plant throughput and recovery. Production of direct shipping lump ore and sinter fines is forecast at around 1.5 million tonnes in 2011 and, based on current and historical resources, growing to approximately 5 million tonnes in 2015 and thereafter. Production from the first four stages is expected to continue at about this rate through to about 2028.

May 1, 2011

By B. D. Thompson

Many mines adopt necessarily conservative backfilling strategies due to a lack of understanding of their backfill behaviour. In the past five years, extensive instrumentation campaigns have focused on measuring in-situ cemented paste backfill behaviour. These tests have resulted in optimised backfilling efficiency through elimination or reduction of cure periods where; i) controls on backfill behaviour are understood, and ii) barricade pressures are demonstrated to be within a safe range using routine monitoring as a required QA/QC procedure. Recently, this work has been extended to consider hydraulic backfill operations. Two stopes have been instrumented at Vale?s Coleman and Garson Ramp mines. The instrumentation and deployment methods are discussed, and representative total earth pressure, pore pressure, and temperature data are presented. In one case, pressures in the stope are relatively low as drainage causes strength gain in the fill and so pressures are arched. In a second example, again, drainage causes strength gain in the fill, but increasing temperatures correlate with pressure increases even during downtimes in filling. These pressure increases are thought to be caused by thermal expansion of the backfill in confined locations. Generally, the instrumentation approach has proven successful in measuring hydraulic backfill behaviour and offers good potential for incorporation into a procedure to safely maximise backfilling efficiency through routine barricade pressure monitoring, when combined with safeguards to ensure adequate fill drainage.

Aug 1, 2013

By Nabeel Khan

Annual oil production from the Canadian Oil Sands in Northern Alberta has been rising for several decades, and more ore and overburden are excavated each year from an increasing number of open pit mines. Overburden meeting certain specifications will be used to dam tailings and fill open pits, but the remaining material must be stored in overburden storage structures (OBSS). Well-designed overburden storage structures are more stable and cost less in the short- and long-term. The purpose of this paper is to explore OBSS designs that will be stable yet economical in the short- and long-term. The geological background of the site is briefly discussed, including the effect of each of the main geologic layers (recently deposited till and muskeg, Clearwater Formation clay shales, McMurray Formation oil sands, and the Devonian limestone) on the slope stability of the OBSS. Cost is considered in the analysis when balancing between minimizing costs (steeper slopes) and acceptable factors of safety (flatter slopes), all the while considering the financial consequences of failure. Potential failure planes are identified and probabilistic analysis is conducted on the critical failure surface. The variations in the factor of safety caused by varying pore water pressure, friction angle, and cohesion, are plotted and discussed.

Jun 1, 2012

By J. P. Messervey

As a result of my field examinations in this Province, I have been struck by the evidence of widespread mineralization in rocks, particularly the limestones of Carboniferous age. Six prospects of lead and zinc or lead alone scattered through the eastern part of the mainland, one copper prospect and three veins of siderite, all point to a period of mineralization subsequent to the forming of the Carboniferous rocks in which they occur. While none of the present prospects are of proved economic importance, still it is possible, and indeed probable, that further prospecting will find concentrations sufficiently large to make mines. It may possibly aid the prospecting for these base metals if the present scraps of information are assembled from various sources, and I will further briefly recount the information as a result of my observations. Gay?s River At Gay's river, midway between Halifax and Truro, and four miles east of the railway, numerous pits and natural exposures show galena and sphalerite in limestone of Carboniferous age, near where it lies unconformably upon slate and quartzite of the gold series. These exposures extend for a length of over one thousand feet along a curving contact. The pits show that on the contact there is a fossiliferous and somewhat porous layer of limestone, which is so impregnated with galena and small amounts of sphalerite as to be of ore grade. Wherever observed, the thickness of this layer is less than two feet.

Jan 1, 1929

By T. Gerritsen, C. Martinez, F. Stober, T Ma, J. R. Frias, M. Sedighy, J. Janzen

Electrode control systems regulate power by physically positioning electrodes. Due to the weight and inertia of the electrodes and hoist equipment, this is a relatively slow process where power fluctuations of less than a few seconds are not fully corrected. Nickel laterite AC furnaces operating in high voltage, shielded arc mode typically incur frequent power variations of approximately +/- 20% or more around the power set point. To provide enhanced power control, Hatch has recently supplied, at commercial scale, a thyristor-switched reactance system called an SPLC. The SPLC incorporates predictive control software to operate furnaces at the maximum transformer rating by reducing the large power swings experienced without the SPLC. The resulting higher average power enables higher production, without increasing transformer or power plant capacity. A 60 MW production version of the SPLC has been commissioned on Falconbridge Dominicana's laterite nickel furnace, yielding excellent results with a 3 to 1 reduction in power fluctuations.

Jan 1, 2005

By H. C. Rickaby

Introduction The township of Swayze, from which the Swayze gold area derives its name, is in the Sudbury mining division, approximately 150 miles northwest of Sudbury. The gold area may be regarded as situated at the southwest corner of a triangular area whose northeast and southeast corners are at Porcupine and Shiningtree, respectively, and whose sides are between 70 miles and 90 miles in length. On a geological map, it would be found that belts of Keewatin greenstones and sediments form the sides of this triangle, and that they surround a large granite mass. Prior to the summer of 1931 the Swayze corner of this triangle had probably been less prospected than the other parts and comparatively little was known of it from the standpoint of gold mining possibilities. The extensive belts of iron formation to the south and west of Swayze received some attention about the year 1909, and during the years 1927 and 1928 some prospecting was done in the townships of Greenlaw and Cunningham, south of Swayze, but chiefly for base-metals- copper, zinc, and lead. In the summer of 1931 a very promising discovery of gold-bearing quartz was made by J. G. and J. L. Kenty, working for the Brett-Trethewey Mines, Ltd., in association with Northern Canada Mining Corporation, and Northland Prospectors, Ltd., and this property, now known as the Kenty Gold Mines, Ltd., has been actively developed with very encouraging results. Following this discovery a6d during the summer of 1932 much prospecting took place in the area, as a result of which a number of other discoveries of gold were made, chiefly to the west of the original find. They are distributed over a wide area, which includes the townships of Rollo, Raney, Swayze, Denyes, Halcrow, and Greenlaw.

Jan 1, 1933

By Paul W. Richardson

"Introduction And AcknowledgmentsTHIS PAPER outlines the geology and discusses the geological problems of the Mindamar mine. It is impossible to acknowledge the contributions of ideas of all the geologists who have worked in the area. Among the more important contributors are K. DeP. Watson, W. S. James, B.S.W. Buffam, and L. J. Weeks, and John MacPherson, the resident geologist at the mine.A mineralogical and chemical study of the ore and country rock is being carried •on by Dr. Watson at the University of California, Los Angeles.General InformationThe Mindamar mine is on Cape Breton Island, forty miles south-west of Sydney (Figure 1). The nearest railway stations are at St. Peters, which is thirty-two miles southwest of the mine, and at Sydney. Good gravel-surfaced roads connect the mine to the railways.The mine is producing at the rate of 600 tons a day of ore containing zinc, lead, copper, and minor amounts of silver and gold. At the present time the mill feed averages 9 .per cent combined metals, of which zinc makes u:p 7 1per cent and lead and copper each 1 per cent.General GeologyThe ore being mined ,by Mindamar occurs in a shear zone parallel to a northeasterly striking, vertically dipping, series of rocks consisting of rhyolite tuff, rhyolite, minor more basic flow rocks, and diorite (Figure 2). In the vicinity of the mine, these rocks have been termed the Mine Series. They belong to the Bourinot group, which has been assigned by L. J. Weeks to the Middle Cambrian. At the latitude of the mine, the Bourinot group is bounded on the northwest by the Stirling fault and extends eastward for two miles."

Jan 1, 1953

By Seher Ata

"Virtual reality, a three-dimensional computer generated environment, has become recognized delivery system for many forms of education. This article describes the application of virtual reality to mineral processing education. An interactive mineral processing visualisation module has been developed at University of New South Wales (UNSW), Australia. The module provides students with an overview of a base metal concentrator, details about each stage of the process, as well as revealing how the mined ore progresses from stage to stage. The module also involves developing a number of instructional based plant layouts and flowsheets in the virtual environment that are intended to assist the user in understanding the essential components of the base metal concentrator.INTRODUCTIONVirtual Reality (VR) is the creation of an artificial environment that is experienced through sights and sounds provided by a computer (Squelch, 2001). The simulated environment is achieved through a host of technologies such as three-dimensional graphics, audio feedback and special peripheral devices to produce interactive environments.VR has been used in diverse fields including medicine (Riener & Harders, 2012), entertainment (Hsu, 2011), military (Manojlovich, Prasithsangaree, Hughes, Chen, & Lewis, 2003), manufacturing (Zimmermann, 2008; Jiang, 2011), and chemical processing (Schofield, Lester, & Wilson 2005; Squires, Andersen, Reklaitis, Jayakumar, & Carmichael, 2014). VR is also becoming recognized delivery system for many forms of education, including engineering education (Bell & Fogler, 1996; Bell & Scott, 1998; Shin, 2002). For example, virtual laboratories have been designed and developed to teach students fundemental features of the heterogeneous catalytic mechanisms and absorption columns (Bell & Fogler, 1995), the multi-phase and multi-component blast furnace iron making process (Babich & Senk, 2009) and to guide students to identify various safety measures while working in real laboratory (Bell & Fogler, 1996)."

Jan 1, 2016

By Juan Pablo Vielma

In this work we study how to incorporate risk control to the generation of ultimate pits when orebodies are modeled through a finite number of conditional simulations. To control risk we consider a chance constraint on the value of the ultimate pit. We incorporate this measure into the generation of ultimate pits by solving a stochastic programming version of the ultimate pit problem. We compare this stochastic programming problem to previous approaches such as generating the ultimate pit for each simulation and the hybrid pit approach introduced by Whittle and Bozorgebrahimi. We also study the effect of using different number of simulations in the generation and evaluation of ultimate pits.

Oct 1, 2009

By Vincent H. Hartung

The process of estimating tailings deposition for a given basin is a relatively tedious process without dedicated software tools. The amount of time required to generate a tailings surface for a given set of conditions tends to limit the number of design alternatives that can be considered for a particular project. Recent innovations in the Surpac Vision mining software include the widely used scripting language TCL (Tool Command Language) that brings with it the ability for non-programmers to extend the software functionality beyond mining applications alone. A software tool was developed using the Surpac Vision scripting language to take advantage of 3D visualization and create a flexible tailings modeling solution. The result is an application that removes much of the drafting overhead required to produce a tailings surface. It provides the means for reviewing alternatives and performing sensitivity analysis with variables such as pond elevation, dam or spigot location and height without a significant increase in overall time for a project.

May 1, 2001

By Seongki Lee

The purpose of this paper is to propose the real-time facility management system framework based on Building Information Model (BIM) and Web of Things. Latest IT such as BIM is rapidly spreading to architecture, civil engineering, engineering and maintenance with the aim of simplifying complex system in buildings and facilities, minimizing operation cost, providing high value services and advancing facility management. In particular, BIM-based management framework design to assist the development of sensor information operation system, which adds convenience to facility maintenance and management, has emerged as a key issue. To this end, this paper proposed conceptual framework for data warehouse, web service and interface that make up real-time facility management system. The paper also produced conceptual methodology on CoRE-based web service platform, mobile device, BIM and WSN mapping.

Aug 1, 2013

By Jorge M. C. Soares

The CO oxidation reaction has been studied on Au/TiO2 catalysts prepared by incipient wetness (IW) and deposition-precipitation (DP) methods. Additionally the assessment of activity was also conducted on simple gold compounds (Au2O3 and Au(OH)3) and their physical mixtures with TiO2. We have found that there are three types of CO2 production from fresh catalysts, which are only dried, namely: Non-catalytic Type I (low temperature CO2 production); Non-catalytic Type II (higher temperature CO2 production) and Catalytic Type III. The DP catalysts are far more active for Type III reaction, showing activity already at room temperature, whereas the IW catalysts generally do not show steady state conversion until T>673 K. This is due to both large particle size and the presence of residual chlorine for the latter. No truly catalytic activity was found for low temperature CO oxidation on gold precursors on their own, although both Au2O3 and Au(OH)3 react well with CO even at room temperature in an irreversible manner (Type I reaction). Despite that, catalytic activity was obtained by mixing Au(OH)3 or Au2O3 with TiO2 which gives further emphasis on the importance of a good contact gold/support and the absence of chlorine.

Oct 1, 2003

By S. N. Dixon

"Maximizing the value of each tonne of processed ore is the goal for all operations. Cyanidation processing of gold-copper ores has been challenging since its first use in 1889. The current practice treats a bleed or the total flow of mill solution to recover copper as copper sulfide (by sulfidization, acidification, recycling, and thickening), or to recover the cyanide (by acidification-volatilizationneutralization). The process presented uses the adsorption of copper cyanide by carbon and the selective elution of copper from carbon to concentrate copper into a smaller stream. Copper contained in the smaller stream is precipitated as copper cyanide.RÉSUMÉ Toutes les exploitations ont pour objectif commun d’optimiser la valeur de chaque tonne de minerai traité. Depuis sa première utilisation en 1889, la méthode de traitement par cyanuration des minerais aurifère et cuprifère s’est révélée complexe. La pratique actuelle traite la saignée ou le débit total d’une solution de traitement du concentrateur pour récupérer le cuivre sous la forme de sulfure de cuivre (par sulfuration, acidification, recyclage et épaississement), ou pour récupérer le cyanure (par acidification, volatilisation et neutralisation). Le procédé présenté dans cet article utilise l’adsorption sur charbon actif de la solution de cyanure de cuivre et l’élution sélective du cuivre depuis le charbon pour concentrer le cuivre en un plus petit jet. Le cuivre contenu dans ce plus petit jet est précipité sous forme de cyanure de cuivre."

Jan 1, 2017

By Joe Price

Canada?s energy future will increasingly depend on a supply of light, sweet crude oil derived from the Athabasca oil sands deposit of North-eastern Alberta. Billions of dollars are being spent on the construction of new and expanded mine and bitumen extraction plants, in situ recovery facilities, pipelines, upgrading installations and all the infrastructure needed to support these projects. The success of the existing operators has also inspired new players, anxious for ?a piece of the action? to come forward with exciting project proposals of their own. None of this investment and spin-off economic activity would be taking place today if events had unfolded differently in this part of the world some one hundred million years ago. The accumulation of sand in rivers, estuaries and in the near-shore marine environment created the great reservoirs that host the enormous oil deposits these projects are designed to exploit. Mine operators of all stripes will likely agree that there are few good ?geological surprises?. With specific reference to oil sand deposits, the geological history determines the distribution of sand, silt and clay bodies, which in turn controls the ore grade. Important design factors including everything from stable pit slope angles to tailings properties reflects events that took place millions of years before. An understanding of the sequence of events that resulted in deposition and preservation of the sediment and oil are important to sound design for both mining and in situ facilities. A geological history of the region is described. Site-specific examples from Syncrude?s operating mines are used to illustrate some of the geological factors that can present design challenges.

May 1, 2003

By Jason Prno

Context ? Climate change an issue of global significance ? Research is lacking ? Study initiated by the David Suzuki Foundation, led by ArcticNorth Consulting Industry Surveying ? 34% and 48% of respondents indicated climate change is already affecting operations ? Majority believed climate change would have negative impacts in the future ? Cost and uncertainty of Future impacts are major barriers to adaptation

May 1, 2010