Search Documents

By Jerry Z. Lu

Belt conveyor design involves the evaluation of belt tensions, drive selection, pulley configuration and other technical issues. The conveyor belt tensions vary with conveyor layout, drive pulley configuration, belt selection, and idler selection. The decisions for the belt conveyor construction always take all technical, commercial and maintenance issues into consideration. A good conveyor design shall provide required operational features and at the same time be cost effective. The common issues for an engineer to face during belt conveyor design include: (1) Conveyor drive selection ? drive with fluid couplings or variable frequency drives; (2) Drive system configurations - single pulley large drives or dual pulley smaller drives, if intermediate tripper booster drives shall be applied, what power ratio should be adopted for a multi-drive conveyor; (3) Gear reducers ? shaft mount drives, right angle gear reducers or parallel gear reducers; (4) Drive pulley lagging - ceramic lagging or rubber lagging; If ceramic lagging, what type should be used. (5) Conveyor speed variation ? If conveyors run at variable speeds, faster speed/lower percentage loading or slower speed/higher percentage loading. In many cases the decision maker find themselves in a dilemma ? technical benefits vs. financial benefits, capital cost vs. operational cost, and capital and operational cost vs. maintenance effort. Although many conveyor design topics above have been discussed in numerous technical papers and design reference books, management executives and inexperienced engineers may be confused and feel lost. The consultation of people around them may lead to different opinions since experiences tend to vary, making the decision making process complicated. The purpose of this paper is to simplify these complicated issues and provide useful guidelines for belt conveyor design. This paper focuses more on providing simple and practical answers and solutions instead of discussing each topic academically and theoretically in depth.

Nov 1, 2011

By Roger Lacroix

Presentation outline Project definition Characterization of mine ventilation systems Strategies in place and results Detailed study (2 mines) Other potential energy savings Conclusions Next steps

Feb 1, 2008

By C. O. Aksoy

Operating the underground marble quarries effectively, it is important to evaluate the deposit blocks economically which are affected by the suitability of the topography and configuration of bedding. The joint sets within the deposit and the spacing between these discontinuties are also of great importance. In this study, the marble deposits that could be geomechanically eligible for underground excavation have been selected throughout Turkey and these selected reserves have been classified accordingly by Q-Rating System. These classified marble deposits that forms groups of 1,2, and 3 (groups were determined by evaluating the O-rating, topography, quarry situation, cracks, joints etc.) are convenient for this type of production. Nevertheless, when the auxiliary factors (topography, location, production method etc.) regarding the deposit have also been investigated, the most convenient sub-group of deposits (Afyon Tiger Skin, Burdur Beige, Diyarbakir Pink and Mugla White) have emerged. The sizing of the pillars have been performed utilising Bieniawski?s stress profile. The LAMODEL software, developed by National Institute for Occupational Safety and Health (NIOSH), USA and run under the laminated displacement discontinuity method, has been used to size the pillars. This work brings in a novel opportunity to Turkey, in which no underground marble quarry has been attempted up-to-date similar to its several examples in Italy, USA, etc. This study serves as a reference for the marble operators and for the pioneering application of laminated displacement discontinuity method in hard rocks.

Apr 1, 2005

By Deng Yang-wu, Zhang Yan, Chen Chun-fei, Luo Xian-ping, Luo Cai-gui

This paper summarizes the ecological imbalance status of abandoned rare-earth element (REE) mines in southern China. These include large areas of vegetation damage, serious water and soil erosion, landslides, mudslides, heavy metal pollution, water pollution, soil contamination, and fluorine pollution. The causes which lead to the ecological imbalances at abandoned rare-earth mines are analyzed, such as: the inadequacies of using vat leaching, heap leaching, and in-situ leaching processes to extract REE resources; low mineral thickness and low grade of REE ore; and low utilization rates of the resource. Southern ionic REE resources are not fully integrated, with limited access and ineffective supervision of REE mining by relevant departments. The ecological recovery research for ionic-type REE mines is lagging behind, and there is no deployable ecological restoration method for REE wasteland. In the end, the following suggestions are made to improve the ecological imbalance status of rare-earth mine in southern China: develop new rare-earth extraction processes, accelerate the integration pace of REE resources, increase investment in ecological restoration research in rare-earth wasteland, and so on.

Jan 1, 2014

By Robert B. Parsons

"Finance Minister Paul Martin's first budget disappointed almost everyone. The business sector was disappointed at the some what feeble attempt to grapple with the country's deficit. The mining industry was disappointed by tax proposals regarding mine reclamation that fall short of the industry's needs. Has anybody been happy with a federal budget? Federal Budget DisappointsThe federal government's budget papers that were tabled on February 22, 1994, contained a rather bizarre mixture of unrelated tax proposals. The budget signals an unexpected attack on the tax treatment of debt settlements, on certain types of corporate reorgani2ations, and on income earned by foreign affiliates. This is an old style budget, which proposes a pot pourri of technical changes and policy initiatives. Mine ReclamationEffective February 23, 1994, a taxpayer's contributions to a prescribed mine reclamation trust fund will be deductible as a current expense. The budget papers do not provide a definition of what will constitute a ""prescribed"" trust: this definition will surface in due course. However, the budget papers indicate that:• income earned in such trusts will be subject to tax each year;• all withdrawals from the trust (including income already taxed) will be included in computing the income for tax purposes of the recipient;• reclamation costs will continue to be fully deductible at the time incurred; and • contributions, trust earnings, and withdrawals will not be taken into account for the purposes of determining a taxpayer's resource allowance."

Jan 1, 1994

By Garth D. Kirkham, James P. Siddorn, Hendri Falck

"Abstract - As an integral part of the Geological Survey of Canada’s EXTECH III Project, a threedimensional computer model has been created of the Con and Giant gold mines in the Yellowknife Greenstone Belt. The Yellowknife Mining Camp has produced a great deal of gold (over 15 million ounces, or 400 000 kg) in the past sixty years and the prevailing assumption is that the mines are at the end of their lives. However, the potential for discovering additional resources using new ideas and technology, and maximizing use of existing data, offers an opportunity to sustain the old mining operations and maintain their contribution to the community.The objectives of this study included the compilation and creation of a three-dimensional Geographic Information System model (combining 3D subsurface data with surface information) to provide a framework for concurrent structural and alteration studies, and to encourage new exploration in the area. A secondary objective was to retain the data in digital format as a historical reference for future remediation efforts, and to document a portion of Canada’s rich mining history.The end result is a database and set of models that have been instrumental in facilitating further exploration in the area, as well as in developing targets for future exploration and mining activities. In addition, the EXTECH III 3D GIS model has made a valuable contribution toward the understanding of the arsenic remediation issues at the Giant mine, and has served as a tool in support of a variety of highly technical engineering studies and for communicating information and problems to the layman and community as a whole."

Jan 1, 2003

By Patrick Laflamme, Jean-François Boulanger

Les minerais de cuivre sulfurés, qui représentent 80% de la production mondiale de cuivre, imposent une étape de concentration des minéraux, premièrement pour atteindre une teneur en cuivre minimale qui permette le traitement pyrométallurgique, mais aussi pour limiter la présence d’élément pénalisants (délétères). Cette introduction offre un survol des principes, limites et pistes d’améliorations touchant la concentration des minéraux de cuivre.

May 2, 2024

By J. Stumper

The control of the distribution and movement of liquid water is crucial for increased reliability and durability of PEM fuel cells: whereas the proton exchange membrane requires a minimum amount of liquid water for optimum operation, water excess in the GDL will impede reactant gas access to the catalyst layer thereby reducing performance. In order to understand the relationships between water management on one hand and fuel cell performance and durability on the other, Ballard has been developing a number of minimally invasive techniques that can throw light on the role of liquid water for both cell performance and durability. This paper introduces a novel measurement method that can provide information about the amount and distribution of liquid water under operation. It is shown how the MEA Resistance and Electrode Diffusivity (MRED) method can be used to determine i) the amount of liquid water in the fuel cell, ii) the pure ohmic cell resistance and iii) the O2 -diffusivity of the cathode. Furthermore, through a combination of the MRED method with current mapping it is possible to determine spatially resolved MEA resistance profiles.

Jan 1, 2005

"Since the publication of a literature review on this topic (McIvor and Finch. 1986), the author has been involved in more than thirty rod milling efficiency tests at seven different milling operations. There have also been several interesting additional articles on rod milling found in the literature. This update describes the most important findings from investigations carried out since the previous review, as well as developments in the techniques used to evaluate the grinding efficiency of rod mills.Rod Mill Power DrawA series of power draw versus charge level measurements were taken on the rod mills at Leg Mines Selbaie and Kidd Creek Mines Limited (McIvor. 1989). These revealed a significant (about 10070) loss in power draw with the installation of new liners, a common observation among rod mill operators. This loss in power draw depends on the liner design, particularly the average thickness and lifting face profile of the new liner. The theoretical power usage of both mills was approximately 5070 lower than that given by the Allis-Chalmers power draw formula (Rowland. 1982).The shape of the power draw versus charge level curve suggested an opportunity for reducing media consumption. By increasing mill speed, power draw could be maintained with a smaller mill load, most significantly for mills operating with high charge levels. Analysis of data from 62 installations confirmed this (McIvor, 1989). On average, a 10 percentage point increase in critical speed results in a 15070 in specific media consumption (Le. kg of steel consumed per kWh of energy consumed). Table 1 lists a number of relatively high speed rod milling installations. No negative effects on the drive train, liner life, or the tendency for rods to tangle have been reported. A reduced lifting angle of the new liner leading face (e.g. 45 versus 90 degrees from the mill perimeter) is recommended for higher speed rod mills (Leclerq, 1990)."

Jan 1, 1995

By T. Eger

Load Haul Dump vehicles (LHD) are extensively used in underground mining however equipment design and operating conditions contribute to restricted operator?s visibility. The inability to clearly see people, objects or hazards around the machine has contributed to a number of accidents including fatal injuries. In order to identify vehicle design characteristics resulting in restricted and blocked sightlines visibility assessments are traditionally completed in the field. However, field methods are unable to evaluate visibility under dynamic operating conditions and are limited in their ability to provide feedback on the impact of various operator characteristics such as sitting height, for example. Results of this research show computer simulation and virtual reality can be successfully used to evaluate visibility during the operation of LHD vehicles. In order to benefit from virtual reality applications the work environment, LHD vehicle and human posture need to be represented as accurately as possible. A computer simulation program with ergonomic ana lysis features, Classic JACK 3.1, was successfully used. Threedimensional CAD models of LHD vehicles were developed from manufacturer specifications and pictur es taken from LHD vehicles currently in use. The LHD models were imported into the JACK environment, a digital human was positioned in the cab of the LHD vehicle and the vehicle and human where driven over a typical mine route. Real-time feedback in the JACK program was used to identify what the operator could see under different operating conditions. Machine characteristics and operating scenarios resulting in impaired visibility were successfully identified with this method. The JACK program can also provide real-time feedback on the human?s joint forces and torques, strength requirements, postural comfort, and metabolic energy expenditure. As a result, this method could be used to successfully evaluate musculoskeletal injury risk factors along with system design recommendations to improve workplace safety and productivity in any setting. The LHD VRML files imported into JACK have also been combined with environment files into other VR software packages (e.g. Maverik) to view in a VRL facility, managed by MIRARCO at Laurentian University. The VR models using these packages can be viewed in stereo to provide better appreciation of spatial visibility issues.

May 1, 2003

By A. J. A. Janse

The Argyle diamond mine is located in the Kimberley region in the northern part of Western Australia at approximately 16°43'S, 128°23'E in subtropical bush/shrub savannah. The 46 ha (113 acres) pipe is situated in the Halls Creek mobile zone, which was cratonized about 1800 Ma ago and adjoins the Kimberley Block, a plateau upheld by Early to Middle Proterozoic rocks underlain by presumably Archean basement. The crater and upper pipe zones of the diatreme have been preserved within tilted and faulted strata of Middle to Late Proterozoic age. Its age of intrusion is about 1178 Ma. The diatreme rock is not kimberlite but olivine lamproite which was not recognized as a primary diamond host rock until 1978. The Kalumburu Joint Venture, a syndicate of local and overseas mining companies, started in 1972 to prospect the Kimberley Block with a modest annual prospecting budget of $125,000. Annual expenditure doubled each year and reached $1 million in 1975 after which CRA took over management of the newly-formed Ashton Joint Venture with an annual expenditure of $2 million (all figures are in current US dollars). The Argyle diatreme was found near the end of the eighth field season and after a total expenditure of $12 million. Annual production is about 34 million carats which places Australia as the world's number one diamond-producing country, although, because of the low value per carat, it is number four in terms of total annual value. The global cost required for a major diamond mine is between $300 and $400 million, with a discovery every 10 to 12 years. Because Canada contains large areas of prospective platform rocks underlain by Archean basement it is likely that a major diamond deposit does exist there. It is probable that it will be found before the end of this decade and exploration expenditure may be in the order of $100 million.

Jan 1, 1992

By Theo. Koulomzine

"The property of Consolidated Central Cadillac Mines, Limited, consists of 1,103 acres formerly held by Central Cadillac Mines, Limited, and Wood Cadillac Mines, Limited. Both mines have been partly developed to depths of 565 and 1,000 feet respectively, and from 1939 to 1943 they produced gold, with small amounts of silver and tungsten, having a total value of $2,208,528 from 377,489 tons of ore. The average grade of the ore was $5.85 a ton . Less than 10 per cent of the ore hoisted was discarded by sorting. New development work, carried out since the former Wood property has been purchased by Central Cadillac, has shown that the tonnage indicated by mine workings and diamond drilling exceeds 2,000 tons per vertical foot.The property lies between the claims of Kewagama Gold Mines, Limited, and Pandora Cadillac Gold Mines, Limited, and straddles the Cadillac 'break' for a length of nearly 1 ½ miles. The main workings are 1 3/4 miles east of the well-known O'Brien gold mine.GEOLOGYOutcrops are very scarce, with none at all of the most important horizons, so that the general geology shown in Fig. 1 is deduced mostly from underground workings and diamond drilling. Fig. 2 is a vertical cross-section and Fig. 3 a longitudinal section through the ore zone.The ore lies within a belt of Blake River volcanics which is approximately 600 feet wide and is flanked on the north and south, respectively, by Cadillac and Kewagama sediments. All the formations have a nearly vertical attitude. The Blake River belt consists essentially of well sheared volcanic tulfs, but associated with these in the northern part are a number of bands of iron formation and the central part, to a width of 100 feet, is occupied by talc schists, making the Cadillac fault proper. Intruding the volcanics south of the Cadillac shear zone are dykes of two types- finegrained aplite or quartz albitite, and porphyry; both consist essentially of albite and quartz and are distinguishable only by the grain size. They have the general east-west trend of the formations they intrude."

Jan 1, 1954

By V. Vekris

A diverse patent portfolio and an effective intellectual property strategy are vital in today’s small business world. Not only does a diverse patent portfolio enable a company to secure a monopoly within the market, it greatly increases the value of a company’s intangible assets and keeps competitors at bay. An overview of the patenting process as it pertains specifically to the materials science-related start-ups will be given, together with a summary of some general patenting strategies and a review of some patenting errors to be avoided, such as premature disclosure of the invention to the public. Additionally, a review of new “green technology” initiatives recently adopted by Patent Offices around the world is also provided. These initiatives are expected to greatly benefit patent applicants in the fields of metallurgy and mining, where research efforts are often directed to environmentally-friendly products and processes. INTRODUCTION Patents are playing an increasingly significant role in the business world. A diverse patent portfolio can enable a company to secure a monopoly within the market, which can provide a competitive advantage over competitors. At the same time, patent portfolio of any size can greatly contribute to the total value of a company’s intangible assets. As an example, Nortel entertained bids in 2011 for its portfolio of about 4000 patents, a large portion of which were directed to 3G- and 4G-mobile communication technologies. The portfolio was eventually sold for $4.5 billion to a consortium including Apple, EMC, Ericsson, Microsoft, Research in Motion, and Sony. Copper mining, and indeed the global mining industry as a whole, is facing challenges. Ore deposits are increasingly low grade, complex, and deeper in the ground, rendering copper mining operations more difficult and costly. Production costs are increasing. According to one study, the cost of producing copper has increased by an average of 10% per year since 2005 (Cantallopts, 2017). To illustrate, the cost of producing a pound of copper in 2005 was 90 cents, but had increased to 217 cents by 2014.

Jan 1, 2019

By A. R. Sheik, A. A. Baba, M. K. Ghosh, K. Sanjay, R. B. Bale, A. G. F. Alabi, F. A. Adekola, L. Ibrahim

"This paper studies the characterization and dissolution of a Nigerian pyrolusite ore, reporting the results of ore physicochemical analyses and detailed ore characterization before and after leaching at optimal conditions. Ore dissolution rate increased proportional to acid concentration and temperature, but decreased with ore particle size. In a 4 M H2SO4 solution at 80°C with a particle size of –90+75 µm and moderate agitation, ore dissolution rate reached 78.7%. Unleached residue produced under optimal leaching conditions consisted of silica with admixtures of cristobalite and stishovite. The calculated activation energy supported the proposed diffusion control mechanism for the process.RÉSUMÉ Le présent article étudie la caractérisation et la dissolution d’un minerai de pyrolusite du Nigeria, il donne les résultats des analyses physicochimiques du minerai et de la caractérisation détaillée du minerai avant et après la lixiviation sous des conditions optimales. Le taux de dissolution du minerai augmentait proportionnellement à la concentration de l’acide mais décroissait avec la taille des particules. Dans une solution 4 M H2SO4 à 80 °C, avec une granulométrie de –90+75 µm et une agitation modérée, le taux de dissolution du minerai a atteint 78,7 %. Les résidus produits sous des conditions optimales de lixiviation étaient constitués de silice avec un mélange de cristobalite et de stishovite. L’énergie calculée d’activation supportait le mécanisme de contrôle de la diffusion proposé pour le procédé."

Jan 1, 2016

By Makhlouf Boubahziz

The HNIA field is part of the Tinrhert project which consists of developing 17 fields containing essentially gas with a few small rings of oil. It is considered as one of the main fields in this project in terms of its area and the number of geological structures that has formed it. It is a wide anticline of Cambro-Ordovician age, orientated NNE-SSW and located in the South-eastern part of Illizi basin. This structure extends from Alrar-center in the North, to the North of In Amenas in the South. The area is 1350 km2. The main reservoirs forming HNIA field are the Devonian (F2, F3 and F4), Siluro-Devonian (F6) and Cambro-Ordovician. These latest are formed by 4 sandy units alternated by layers of shale and shaly silt termed from the base to the top as follow: Unit II, Unit III-3U, Unit IV-2L and Unit IV3; these units are the subject of this study. The HNIA field is essentially gas, up to day this field is at the stage of appraisal and evaluation in order to establish a development plan; therefore the main target of this study is to contribute to this frame work. The following objectives are: ?To build a structural model of the study area. ?To integrate all the sedimentological, structural and petrophysical data in order to build a 3D geological model

Aug 1, 2013

By N. Molaei, E. R. Bobicki

The continued demand for mineral products, coupled with the depletion of high-grade ore resources, has led to the mining of lower grade ores, which often require fine grinding to achieve mineral liberation. Regrinding of low-grade ores results in the production of fine gangue mineral solids and produces vast quantities of fluid fine tailings which are difficult to separate from water, particularly if they are composed of clay minerals. Organic synthetic polymers and inorganic salts have been widely applied in flocculation of colloidal suspensions in the treatment of mining tailings. However, there are growing concerns regarding their impact on the environment and human health. Recently, extracellular biopolymer flocculants or bioflocculants have attracted much attention as alternative reagents. In this study, much effort has been devoted to considering the effectiveness of protein and polysaccharide-based biopolymers for the dewatering of clay slurries. The interaction between kaolinite and illite clays and biopolymers was investigated via settling tests at pH 7 and 10. Zeta potential measurements were also conducted as a complementary technique. Results showed that protamine and lysozyme protein- based biopolymers were generally the more effective bioflocculants. Pectin, a polysaccharide-based biopolymer, showed a dispersing effect and has the potential to be used as a dispersant and/or depressant for clay minerals in froth flotation. INTRODUCTION With the depletion of high-grade ore resources, the need for mining of low-grade ores has increased over the past few decades (Bourgès-Gastaud, Stoltz, Dolez, Blond, & Touze-Foltz, 2014; Chen, Walshe, Fru, Ciborowski, & Weisener, 2013; C. Wang, Harbottle, Liu, & Xu, 2014). Low-grade ores often require fine grinding and contain clay minerals, leading to the generation of fluid fine tailings (FFT). It is a challenging process to separate suspended clay particles from water (Craciun, Manaila, & Stelescu, 2013; Dompierre, Lindsay, Cruz-Hernández, & Halferdahl, 2016; Kasperski & Mikula, 2011; Mercier et al., 2012). Clay minerals form stable dispersions in water due to their anisotropic nature, non-spherical morphology and colloidal size (Lagaly & Ziesmer, 2003; Olphen, 1977). The difficulty in separating clay minerals from water has led to the accumulation of vast quantities of FFT in oil sands, phosphate, copper and nickel operations, representing a huge liability for mining companies (Chen et al., 2013; Mercier et al., 2012)

Jan 1, 2019

By M. Hashemzadeh

The efficiency of water use is a top priority for the global minerals industry, especially in regions with limited freshwater supplies. In these areas, the freshwater shortage has prompted mining companies to search for alternatives to freshwater sources. Seawater has been proven to be a potential water source for mineral beneficiation and metal extraction processes. This study compares chalcocite leaching behavior with ferric chloride to that with cupric chloride. We carried out leaching tests with a highly pure chalcocite sample in jacketed reactors under fully controlled pH and solution potential. The effect of chloride concentration, oxidant concentration, and temperature on copper extraction was quantified in both cupric and ferric chloride systems. In the ferric chloride system, increasing ferric concentration showed a positive effect on the first stage of chalcocite leaching. In the second stage, increasing temperature markedly enhanced copper extraction. In the cupric chloride system, chloride concentration presented a considerable effect on both the first and second stages of leaching, while temperature had a remarkable effect only on the second stage. The findings of this study would be beneficial to mine operations aiming to replace fresh water with seawater for heap leaching of chalcocite. INTRODUCTION Mineral processing operations/plants are normally operated adjacent to mines which are often located in remote and arid area, such as northern Chile, southern Peru and Australia with limited access to fresh water (Liu, Moran, & Vink, 2011, 2013). Water scarcity in these areas has prompted mining companies to invest in sustainable technologies to reduce the water use and/or increase the water use efficiency. One of the current sustainable approaches in mineral processing operations is to replace fresh water with seawater. Seawater is now being increasingly used for mineral beneficiation and metal extraction processes (Hernández et al., 2015). Another application of seawater could be for heap leaching of copper secondary sulfides, mainly chalcocite. However, the high concentration of chloride ion in seawater may significantly affect leaching kinetics of copper sulfide concentrates and ores (Watling et al., 2014). Therefore, it is essential to develop a fundamental understanding of the leaching of chalcocite in chloride media.

Jan 1, 2019

By T. Gonzales, S. Thakurdin

The conducting of risk reviews is an essential activity in ensuring safe operating conditions, both during project design phases and for existing facilities. The following paper presents a structured approach to the conducting of risk reviews for existing operations, including descriptions of supporting documentation and guidelines for on-site review activities. The conducting of regular site risk reviews and safety audits is crucial in ensuring the continued safe operation of existing facilities, particularly in the copper industry where numerous processes and unit operations can present catastrophic risks, both in terms of loss of life and financial liability. The structured approach presented aims to provide a logical and comprehensive analysis of risks to align safety-related facilities and procedures with current industry best practice and ensure consistency across multiple client operations. INTRODUCTION The production of copper, whether by pyrometallurgical or hydrometallurgical process routes, carries significant inherent safety risks. Production volumes are relatively large, often requiring complex processing routes, multiple production trains and a variety of supporting ancillary facilities. Furthermore, considering the relatively large size of ore reserves, copper production plants can have operational lives well beyond the typical design duration of 20 years. In this context, the conducting of regular risk reviews is essential in ensuring safe operating conditions and aligning facilities with current industry best practices. Risk reviews and safety audits can take various forms and have various areas of focus. The methodologies and approaches described below relate specifically to catastrophic risks, defined broadly as risks that carry the potential for multiple fatalities and significant financial losses. Focus is given to existing facilities and does not consider the risk-related activities such as hazard and operability (HAZOP) studies conducted during plant design. The structured approach presented aims to provide a guide for effective site- based audits and a logical analysis of risks identified. RISK CLASSIFICATION Table 1 provides a typical summary of the classification of risk types and the associated consequence categories and descriptions. It illustrates the descriptions of a catastrophic risk in terms of the broad categories of Health & Safety, Environment, Financial, Image & Reputation and Legal & Compliance. In terms of the Financial category, numeric costs ranges are often prescribed depending on the financial characteristics of the specific operation and the associated parent company.

Jan 1, 2019

By DALE MacGREGOR, VERA TUREK

The Blue Mountain nepheline syenite deposit has been the subject of several detailed studies. It has been variously referred to as an intrusive stock, a metasomatic deposit, an intrusive sill and a metamorphic-metasomatic body. The body is divided into six mineralogical zones, the first five being based on the characterizing accessory mineral; muscovite, muscovitemagnetite, biotite-muscovite, biotite, hornblende and pink syenite. Mining currently takes place only in the biotite zone. Foliation is particularly prominent in the central (hornblende) zone and near the margins of the nepheline syenite. Majic bodies within the nepheline syenite may represent basic rocks that have been less altered by metasomatism, metamorphosed basic dykes or sloped blocks of metasediments. The most prominent structural features are the northeast-trending folds that have been modified by later north west-trending folds.

Jan 1, 1984

By Richard P. Taylor, Rod Henham

Abstract - Newly discovered pegmatites distributed throughout the sub-surface environs of the Musselwhite Archean gold deposit occur as narrow dikes that intrude most of the major lithological units. The mineralogy and textures of the pegmatite dikes are characteristic of granitic pegmatites of the "Rare-Element Class"; more specifically, they closely resemble varieties of the "Complex-type" granitic pegmatites that are commonly associated with zones of tantalum mineralization. The essential minerals in the dikes comprise albite, quartz, and K-feldspar, together with lesser amounts of mica (including lepidolite), spessartine, tourmaline, and locally, spodumene. Fine-grained (30 µm to 300 µm), tantalum-bearing minerals occur in the quartzo-feldspathic matrix of the dikes as disseminations, in interstices, and in small vugs. The nature of the tantalum-bearing mineral assemblage present in individual pegmatite dikes varies from a simple mineral assemblage composed of ferrocolumbite (with around 39 wt% Ta2O5) in the most northerly dike, to more complex assemblages comprised of manganotantalite (with up to 75 wt% Ta2O5), ferrotapiolite (with up to 79 wt% Ta2O5), and microlite (with up to 76 wt% Ta2O5) that are present in dikes located several kilometers to the south and southwest. The compositional characteristics and textural relationships of the tantalum-bearing minerals in the dikes provide evidence of igneous fractionation trends that are typical of rare-element granitic pegmatites. Such trends suggest that the newly discovered pegmatites represent part of a more extensive group of cogenetic, tantalum-mineralized dikes.

Jan 1, 2001