Search Documents

By Chen Bang, Xia Xiao’ou, Zhang Feng

"Ores with compressive strength lower than 150 MPa are usually easy to be crushed by conventional jaw crushers and cone crushers. However, for hard ores with compressive strength exceeding 150 MPa and 200 MPa and even up to 250 MPa, such as andesite, hard basalt and olivine, it is difficult to reach satisfactory crushing size and yield or difficult to meet service life and stability use requirements of quick-wear parts by using conventional crushers. As continued increase in ore mining depth and constant generation of new type materials, equipment demand for crushing hard ores becomes increasing high. A new type inertia vibrating crusher is designed. It is powered by a high-speed rotating vibration exciter and can obtain required crushing force by adjusting eccentric mass, eccentricity and rotating speed so as to crush various ores with high hardness. This paper introduces the design process of its structure and working principle, discusses the design calculation methods of vibration excitation system, vibration damping and energy storage system and other key mechanism and provides technical references for this type of vibrating crusher.DESIGN PHILOSOPHYThe conventional jaw crusher mainly acquires extrusion force from crank motion to realize crushing. The motor drives the eccentric shaft via the transmission device to bring the moving jaw to swing relative to the stationary jaw. When the moving jaw moves close to the stationary jaw, ores between them are crushed by extrusion; when the moving jaw moves away from the stationary jaw, crushed ores are discharged from the discharge gate at the lower end between the moving jaw and the stationary jaw.The conventional spring cone crusher and the hydraulic cone crusher mainly acquire extrusion force from cranking motion to realize crushing. The motor drives the eccentric sleeve via the transmission device, the moving cone shaft generates an eccentric distance to make cranking motion under the action of the eccentric sleeve. When the moving cone moves close to the stationary cone, ores between them are crushed by extrusion. When the moving cone moves away from the stationary jaw, crushed ores are discharged from the discharge gate at the lower end between the moving cone and the stationary cone under the action of dead weight."

Jan 1, 2016

By Tatyana Alexandrova

The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Technological aspects of processing precious metal ores are examined in two respects: enhancing gold recovery from double refractory ores; and using carbonaceous ores on a production scale. The dispersed carbonaceous matter (DCM) present in concentrates causes the adsorption of [Au(CN)2]- complex on their surface during cyanidation process. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The possibility of rare metals recovery, including rhenium, from black-shale rocks, has been examined. Comparative assessment of analytical methods of rare metals detecting has been carried out. It has been proved that neutron activation analysis is a promising technique. It has been shown that colloid-salt fraction (nanofraction) with particle size less than 1000 nm makes up to 3 wt% of black shale samples and is extracted by water under special conditions. The use of water instead of chemically active reagents provides insolubility of the mineral matrix and fully reflects the colloid-salt element of the samples. To sum up, the justification of the choice of technology for processing of carbon-bearing ores is based on examining the type of carbonaceous matter and its adsorption behavior. When the content of carbon of high degree of metamorphism is considerable, it is possible to recover platinum group elements and rare elements from this type of ores. The obtained results predetermine the general guidelines for creating new methods and techniques of processing carbonaceous material for integral development of solid minerals in the mining and oilfield areas of Russia.

Jan 1, 2016

By Christian Brits, Bob Blain, Lloyd Buckingham, Juliu Stieger, Jean-Francoi Dupont

Barrick Gold Corporation (Barrick) has undertaken innovative methods of evaluating and improving the performance of grinding mills in several of its operations around the world. The results have been positive with some of the mines showing more than 20% net energy improvement leading to more than 43,000 tonnes per year reduction in CO2 emissions in four of the operations reviewed.

Jan 1, 2012

By Rodrigo Madariaga, Tracy T. Morris

The practice of stripping copper starter sheets from titanium blanks to be used in a conventional electrolytic tankhouse has been around since the advent of Electrometallurgy. Historically it has been done manually, utilizing many people to produce in some cases thousands of starter sheets per day. Some other conventional tankhouses have successfully converted to using mechanical means to strip starter sheets or have made the switch to permanent cathodes and although robotics have been around for quite some time they have not been used to strip starter sheets until recently. The Amarillo Copper Refinery began using robotics to strip several years ago and the details to how this came about and how the robots work will be described. INTRODUCTION ASARCO LLC (Asarco) was organized in 1899 as the American Smelting and Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co- products (Marcosson, 1949). Grupo México, S.A.B. de C.V acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, molybdenum, selenium and tellurium. Asarco operates three open-pit mines and mills and two solvent extraction-electrowinning (SX-EW) plants all in Arizona plus a copper smelter in Arizona and a copper refinery in Texas. Figure 1 illustrates how the copper metal comes out of the ground at the mine and ends up as a refined product at the refinery The copper refinery in Texas is known as the Amarillo Copper Refinery (ACR) and is located in Amarillo, Texas. It was built in 1975 to replace 3 other aging refineries and was designed to produce 550,000 tons (500,000 MT) of refined copper per year using conventional starter sheet technology. At the time it was commissioned it was the largest tankhouse in the world at just under 1/2 miles long under one roof.

Jan 1, 2019

By Robert K. Jonas

Mining companies can improve production and reduce costs by using the best available technology to control their operations. Many mines are challenged to use multivariable predictive control due to limited experience or staffing, as well as being concerned over the robustness and sustainability of predictive controls. As a result many mines are not realizing optimal performance from their assets, and thusly are not realizing the production increases or cost reductions that this technology can deliver. Over the past few years, the application of multivariable model-based predictive control has gained acceptance in many mining processes and has proven to be robust and sustainable for some of the most challenging mining processes. New automated modeling and performance monitoring software have greatly simplified the effort to implement and maintain these solutions. In addition, many progressive companies have chosen to co-source the implementation and service of these solutions to assure project success and continued benefits stream. This technology has been successfully applied to a wide variety of processes; grinding mills, alumina digestion, CCD washer and thickeners, kilns, calciners, roasters, flash smelters, heat exchangers, evaporators, and most recently in the demanding process of flotation. This paper discusses the state-of-the art in advance control technologies in the mining industry, including the impact of these technologies on maximizing benefits, and implementing best practices for long term sustainability. Benefits from recent multivariable predictive control applications in copper mining will be reviewed, and the use of the latest predictive control technologies and practices in mining will be discussed.

Oct 1, 2009

By C. B. Webber

"Sherritt Gordon's experience with rubber mill liners began in 1964 at the Lynn Lake Farley Mine and continued at the Fox Mine in 1960, and the Ruttan Mine in 1973. This paper describes the history of the performance of rubber mill liners at the three mine operations.LYNN LAKE - FARLEY MINEThe Lynn Lake Farley Mine, which ceased production in 1976 due to exhausted ore reserves, was a 3500 T.P.D. copper-nickel operation; consisting of two parallel rod mills followed by three stages of ball mill grinding. A circuit modification in 1964 necessitated one of the tertiary ball mills to be used as a pyrrhotite regrind mill. This 8' x 5' Hardinge conical mill drawing 225 HP was initially installed with steel liners and lifters. After several months of operation a routine inspection revealed severe channeling and washing behind the liners which was threatening to erode the ball mill shell. It was thought that the highly acidic condition in the mill, due to grinding 100 º6 pyrrhotite, was accelerating the wear of the steel liners. At this time it was decided to reline the mill with rubber liners to see if the wear problem could be relieved, and in December 1964 a set of Skega rubber liners were installed."

Jan 1, 1981

By T. G. Joseph, R. K. Soni, M. Curley

"Rapid dampening suspension is a proposed suspension design for ultra-class haulers that is intended to avoid metal-to-metal contact inside a strut and under shock loading, thus improving ride quality and ameliorating fatigue loading issues on a hauler structure. Laboratory testing has shown the ability of the proposed design to reduce the opportunity for bottoming out, that is, metal-to-metal contact between the colliding ends of oleo-pneumatic, two-piece suspension struts during the compression cycle. This paper predicts the performance of a full-size rapid dampening suspension strut by applying scaling rules to test the proposed design based on a set of field data from a Caterpillar 797B ultra-class haul truck operating in the oil sands region of the province of Alberta, Canada. The predicted performance of the suspension strut is compared to that of the original equipment manufacturer model, which was monitored on board the truck during field data collection. ¦ KEYWORDS Haul truck, Original equipment manufacturer (OEM), Rapid dampening, Strut, Suspension RÉSUMÉ La suspension à amortissement rapide est une conception de suspension proposée pour des camions de transport de catégorie ultra-class (des engins dont la charge utile dépasse les 320 tonnes métriques), visant à empêcher un contact métal sur métal à l’intérieur d’une jambe de suspension et dans des conditions de choc au chargement. Elle améliore la qualité du roulement et les problèmes de charge de fatigue sur la structure d’un camion de transport. Les essais en laboratoire ont confirmé que la concep¬tion proposée évitera au cylindre interne de heurter le cylindre externe, autrement dit empêchera le contact métal sur métal des jambes de suspension oléopneumatique en deux parties pendant le cycle de compres¬sion. Cet article prévoit la performance d’une jambe de suspension à amortissement rapide à taille réelle en appliquant les lois d’échelle afin de mettre à l’essai la conception proposée, sur la base d’une série de données de terrain relatives à un camion de transport 797B de catégorie ultra-class de Caterpillar (aujourd’hui remplacé par le nouveau modèle 797F) utilisé dans la région des sables bitumineux de la pro¬vince de l’Alberta, Canada. On compare la performance prévue de la jambe de suspension à celle du modèle du fabricant d’équipement d’origine (FEO), qui a été contrôlée à bord du tombereau pendant la collecte des données de terrain. ¦ MOTS CLÉS amortissement rapide, camion de transport, fabricant d’équipement d’origine (FEO), jambe de suspension, suspensionINTRODUCTION Research basis for the paper This paper is based on the unpublished MSc thesis work of El-Sayed (2003), Santos (2007), and Soni (2009) under the direction of Dr. Tim Joseph within the oil sands–equipment interactions program (OsEIP). OsEIP is part of the Alberta equipment–ground interactions syndicate (AEGIS) surface mining research group, School of Mining and Petroleum Engineering, University of Alberta. The aforementioned work spanned a decade of progressive studies into rapid dampening suspension systems, leading to the scale performance indications highlighted here. Although this paper uses a specific Caterpillar 797B suspension strut for field monitoring and as a basis for scale prediction of a modified rapid dampening suspension strut design, the design scaling principles used here could be applicable to any such design change consideration for an oleo-pneumatic suspension system."

Jan 1, 2019

By Francisco Tamargo

"This paper refers to a new process for the full recovery (above 98%) of zinc and other valuable metals (Pb, Ag, Au) accompanying zinc in its concentrates while iron is separated as a marketable product free of any harmful impurities and suitable for sale to the cement industry. The process has been especially designed to achieve the following goals: maximizing the recovery of zinc and those valuable metals that are present in most zinc concentrates (lead, silver, gold); allowing the recovery of other valuable metals such as indium or germanium that could be present in some zinc concentrates; avoiding or minimizing the need for residue disposal in safe areas as it is the common practice nowadays in the zinc industry. Finally, the process achieves the previously related goals at a competitive cost, in line with the existing more efficient operations while using conventional equipment working under atmospheric conditions. The new process can be easily implemented in those smelters using the jarosite or goethite processes as well as in those smelters using direct leaching as a part of the processing facilities. A study has already been conducted on the use of jarosite in the cement manufacturing process, in the raw mix preparation as well as for a set controller. It shows that use of clean jarosite in the manufacture of ordinary Portland cement can result in improved quality of the clinker. Jarosite showed compatibility to influence the burning characteristics of the cement raw mixes. The presence of SO3 bearing mineral phases such as natrojarosite showed the suitability of clean jarosite for use as a set controller in cement production.INTRODUCTION Iron is by far the most abundant impurity accompanying zinc in its concentrates, and consequently, iron residue disposal is a major environmental concern for many zinc smelters in the world. This is especially true during the last 30 years when environmental restrictions became more and more strict. Much research work has been carried out during the last 30 years to try to find a solution for this important issue, but with little success. Only the jarofix process represents a partial solution to this problem as jarofix is stored nearby the smelters with certain limitations as a non-contaminant residue. However, it does not avoid the need to dispose of an important amount of residues every year, representing an environmental liability. Meanwhile, the number of countries limiting or banning the disposal of iron residues generated by the zinc smelters is growing, so that the solution to this problem is becoming an urgent matter right now. At the same time, the lack of appropriate available land for iron disposal is also a major concern in many cases."

Jan 1, 2016

By Lee Nichols

The Oil Sand Industry in northern Alberta, Canada, disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called Consolidated Tailings or Composite Tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities. Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are long-term stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface. The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process.

May 1, 2004

By P. Mattar

The geotechnical importance of studying fluid flow through porous media and soils in particular, becomes evident when dealing with groundwater movement in surficial geomaterials that can be initiated by hydraulic gradients that develop during construction activity, groundwater extraction, impounding of reservoirs and groundwater recharge during adverse climatic events. In a geotechnical context, rocks are regarded as virtually impermeable materials, with comparatively greater resistance to flow of water through their pore structure. The importance of the permeability of rocks comes to the forefront when deep geologic formations are used in geoenvironmental activities for disposal of hazardous and toxic materials. The permeability of the rocks encountered is of critical importance to these geoenvironmental activities since the movement or transport of the hazardous materials during their eventual release will be largely governed by the permeability characteristics of the geologic formation. The estimation of the permeability characteristic of geologic formations is a non-trivial exercise since the measure of permeability can be influenced by the scale at which the measurement is made. Regional-scale and borehole-scale estimates of the permeability can be greatly influenced by the inhomogeneities, including fractures, fissures, solution channels and other anomalies that are present in naturally occurring geologic media. These anomalies are considered to be site specific and can only be determined in a reliable fashion by either conducting tests at the appropriate scale or in the regional-scale through inverse analysis of tracer movement patterns in rock masses. The estimation of the permeability of intact units of a geologic medium has important geoenvironmental applications in connection with storage of wastes since the units in which repositories will be located should be sparsely fractured and the sealing of the fractures and fissures are a prerequisite to developing an efficient solution for storage. The intact permeability of geomaterials is therefore regarded as an important property that influences efficiency and reliability of geoenvironmental solutions for deep geologic disposal. The permeability of geomaterials such as concrete and cementitious grouts are also important to many geoenvironmental and infrastructure applications where durability of structural materials in general and cements used for sealing deep boreholes and other access shafts employed in waste management endeavours is influenced by the permeability characteristics of these materials

May 1, 2009

By Tao Cheng

Previous research and applications in construction resource optimization have focused on tracking the location of material and equipment. There is a lack of studies on automated monitoring of the interaction between workers and equipment for safety purposes. This paper presents a new approach for measuring the safety performance of construction personnel particularly when they work in very close proximity to moving equipment as well as static hazards such as chemical and flammable substances. A method of generating hazardous zones according to the geometric and kinematic characteristics of the considered hazard is introduced. The spatio-temporal relationships between the hazardous zones and workers? positioning data collected by real-time location sensing technology are automatically analyzed. This approach has been validated in a controlled test bed environment that simulates a construction site. Results indicate that worker?s safety performance of selected activities can be automatically and reliably measured using the developed approach. Furthermore, a heat map is generated for visualizing proximity related issues in the test bed using the computed results.

Aug 1, 2013

By B. Jakovljevic, M. D. Soderstrom, T. McCallum, A. J. Quilodrán

Cytec has developed a new organophosphorus based solvent extraction (SX) reagent for rare earth separations. The new product, CYANEX® 572, has been formulated to allow efficient extraction while minimizing the strip acid requirements. The optimization of formulation strength is expected to significantly reduce the operating costs of these circuits. Modeling capabilities for CYANEX® 572 (similar to those used successfully in Cu and Co/Ni SX) have also been developed to aid in the design and optimization of the SX circuits. Simulations will be shown comparing CYANEX® 572 to a traditional rare earth extractant.

Jan 1, 2014

By Robert B. Parsons

"Canada doesn't really have a tax system for mining - it has eleven separate tax systems! The consequent maze adds some undefinable margin of difficulty to making investment decisions in Canada. But, this 11U1Ze is not likely to be simplified. Solution: learn it and sell it! Intricate Network of Winding PathwaysWebster's New World Dictionary defines the word ""maze"" as follows: ""a confusing, intricate network of winding pathways; labyrinth ... a state of confusion or bewilderment"". Webster's does not go on to give an example of a maze, but the dictionary could easily have referred to the taxation of a Canadian mining operation. The uninitiated would almost certainly look upon such taxation as a maze of the most perplexing sort.Twenty years ago, Canada's tax system was really quite simple. It is true that Canadian mining profits were subject to three levels of taxation (federal income tax, provincial income tax, and provincial mining tax), but this didn't pose a problem. Prior to 1974, at least the provincial income tax systems were somewhat the same in terms of rules .and rates, and even the provincial mining tax systems resembled one another. Mining profits were subject to pretty much the same rules, no matter what province or territory hosted the mine. Those were the “good old days” one could even dare to generalize about tax rates without fear of being labelled an imbecile!"

Jan 1, 1994

By M. Honarmand, Z. Moezifar, H. Ranjbar

Abstract - The Sar Cheshmeh area covers an area of 640 km2, and is located in the southern part of the Iranian Volcanic-Sedimentary Belt. ETM+ images have been used for alteration mapping. The Crosta method was found useful for enhancing exposed areas containing hydroxyl and iron oxide minerals. However, field checking has shown that this method is not able to identify all the known areas of hydrothermal alteration. Many of these altered areas are also not clearly resolved in the geophysical data. In order to improve resolution of such areas, integration of remote sensing and geophysical data may be helpful. The Darrehzar Cu deposit was chosen as a control area. The data have been divided into two sets: explanatory and target variables. The explanatory data are Landsat hydroxyl and iron oxide images and airborne geophysical data (K, U, and Th total counts, and total magnetics). The target variables are rock geochemistry and ground geophysics. Data analysis and integration of geophysical and remote sensing data were performed using directed principal components. This technique is found to be useful for the delineation of hydrothermally altered areas with more confidence.

Jan 1, 2002

The use of roof bolting gave promise of substantial economic benefits to Continuous Miner operations at Michel Colliery. As the first step in the adoption of bolting, 142 anchorage tests, employing six types of anchor shells, were made in three mines. Significant differences were found in the anchorage capabilities of the various shells and the various roof rocks. Introduction S PORADIC attempts at roof bolting had been made at Michel Colliery over a period of ten years. Results were indifferent or inconclusive. A concerted effort was not made, because a compelling need for bolting did not exist. By 1962, however, the advent of Continuous Miners had brought a new significance to roof bolting and, at the same time, the increasing price and scarcity of mine timber made bolting materials more competitive in cost. A fresh appraisal of bolting, therefore, became justified and necessary. The potential benefits of roof bolting at Michel are several.

Jan 1, 1963

By Christopher McElman

Real-time mine management solutions have evolved over time from closed, proprietary solutions, to a "system of systems" that may include a wide variety of off-the-shelf components and technologies. Modular Mining Systems has embraced open standards for their NextGen products to bridge the technology gaps between these systems. However, the remaining logical gaps must be overcome, in order to achieve truly seamless integration between discrete systems. When dealing with volatile real-time management problems, the effectiveness of business process modeling and middle-ware can break down. Scientific principles of military command and control applied to mining domain help to achieve better alignment and reach the highest level of integration. The combination of open standards and off-the-shelf hardware and software with a deliberately structured command-and-control approach provides a clear evolutionary path from ad-hoc connected systems towards real-time management of a seamlessly integrated digital mine.

Oct 1, 2009

By E. Marcotte

"Technology developments and improvements are imperative to maintain a viable mineral processing industry. In order to achieve optimum implementation of technology in processing plants, safety conscious and efficient work forces are required. Effective management methods are required to prevent employee injuries, equipment or environmental damage and process losses. Good leadership also provides for employees to perform their work in the safest and most efficient manners to attain optimum recoveries of the valuable minerals and produce high quality mill products. Equipment and processes must be designed, operated and maintained as required to assure safe and efficient mineral processing.INTRODUCTIONThe Canadian mining industry must contend with many challenges to attain and maintain a competitive position in today's global market. Canadian Mineral Processors play a vital role in meeting the challenges and achieving optimum mineral productivity.Ongoing technology developments and improvements continue to be imperative to maintain a viable mineral processing industry. The efficient implementation of technology developments requires a safety conscious, skillful and productive work force.In addition to technical and human resources, challenges may also include governments, labour unions or environmental advocates who at times may appear to be misguided or unrealistic. Canadian Mineral Processors must not allow themselves to be overwhelmed by these apparent obstacles but must use their demonstrated ingenuity to achieve successful solutions.It should be recognized that the majority of the Canadian work force are, in fact, a potentially talented and skillful people with ambitions to excel. As leaders of people, we must provide the methodology, incentive and direction that will allow our work forces to realize their ambitions. If the potentials of our work forces are not recognized and leadership is not properly exercised much loss will occur. That is, safe effective and efficient work will not be achieved."

Jan 1, 1993

By Guy Chevalier

QCM?s pellet plant, located in Port-Cartier, Quebec, produces up to 8.6 million tons of iron ore pellets annually. Four different types are produced: three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the installation of new process equipment to improve the reducibility of direct reduction pellets (DR pellet). The findings, the equipment selection and some post start-up modifications are presented. This low silica DR pellet is used in Midrex and HyL shaft furnaces. A good DR pellet has to meet strict chemical, physical and metallurgical specifications. An important metallurgical property is its ability to release oxygen when exposed to reducing gases. Considering that the market for DR pellets is expanding and being aware that reducibility is critical for our clients, a program to improve the latter was undertaken. Test work showed that one factor which has a negative effect on reducibility is the proportion of particles larger than 75 microns. Knowing that the best way to reduce the amount of coarse particles was to close our open grinding circuits, we began evaluating the most suitable classification equipment applicable to our process operations. We settled on hydro-classifiers based on their very sharp cut and their low operating costs. In light of the hydro-classifiers performance it was also decided to replace the hydro-cyclones of an already closed circuit.

May 1, 2003

By P. Hickey, A. Oliver

"In March 1993, Ram Raising Limited was faced with a challenge. Placer Dome Incorporated, Dome Mine Division requested from Ram Raising that they design station excavation into the existing No. 8 shaft from No. 3 mine levels. This work had to be done without loss of production time in the underground department.Due to the time frame of the project, every detail had to be carefully considered, with extra care that all pros and cons had been worked out.Ram Raising submitted a work Plan that had been worked out with the Redpath Group which included the infrastructure requirements; the engineering design; the scheduling and sequence of work; and the excavation design and blasting procedures.A proposal was' put together by both Ram Raising and Placer Dome outlining the infrastructure requirements, including the engineering design, scheduling and sequence of the work, excavation design and blasting procedures. The proposal accepted by Placer Dome and, on July 3D, 1993 work commenced to breakthrough eight stations. Work continued until December 1993 with the completion off our stations. The project was then stopped to allow the station access drifts from No.3 mine to be completed. The second phase of the project began on May 27 and was completed on September 15, 1994.This paper shows how, through innovative design and the full cooperation between client and contractor, a project of this nature can be completed successfully."

Jan 1, 1995

By Bordeaux Sciences Agro-INRA UMR 1065 SAVE, S. Piutti, E. Benizri, S. Lopez

Ultramafic soils display high concentrations of nickel (Ni) and a number of nutrient deficiencies (e.g. N, K, P). Ni-hyperaccumulator plants have evolved on such environments, developed specific metal homeostasis showing concentrations of Ni sometimes above 1% in their aerial biomass (Baker & Brooks 1989). Alyssum murale, a Ni-hyperaccumulator, is commonly found around the Mediterranean but can grow on non-ultramafic soils as well, with an altitudinal extension ranging from sea level to 2000 m.a.s.l. Rhizosphere bacterial communities associated with Ni-hyperaccumulator plants can differ from those of non-accumulating plants growing at the same site. Among edaphic factors that could influence the phylogenetic structure of the bacterial communities, altitude and metal-bioavailability and in particular nickel could be significant. However, most studies have focused on analyzing soils with techniques that provide little detail about the phylogenetic structure of these bacterial communities present in ultramafic soils. The objectives of this study were to understand the specific changes in the structure of A. murale rhizosphere bacterial community that occur across two gradients: 1°) elevation and 2°) Ni geochemistry, using pyrosequencing technique (454-pyrosequencing of 16S rRNA gene). It was found that the higher the soil chemically-available Ni contents, the higher the relative abundance of Proteobacteria and Actinobacteria. On the contrary, the abundance of TM7 decreased with increasing levels of available Ni. Moreover, Chloroflexi was present with 53 to 77% of relative abundance. These results demonstrate that soil chemically-available Ni drives the bacterial community diversity in the rhizosphere of Alyssum murale regardless the elevation gradient and other different soil physicochemical parameters. These results should now be confirmed in different ultramafic edaphic environments worldwide (e.g. ultramafic lateritic covers) and in the rhizosphere of different hyperaccumulator taxa.

Jan 1, 2016