Search Documents

By T. G. Joseph

The strain softening relationship developed in part 1 is now applied to coal. Having determined the post-failure stress-strain curve for coal specimens, this information can then be used in a finite element program, such as Phase 2, to examine the post failure characteristics of coal pillars. Using example data, the strength of coal pillars of different width/height ratios are estimated and compared with well-known empirical pillar size-strength relationships. In addition, the post-failure stress-strain behaviour of a coal pillar is compared with an empirical relationship reported in the literature.

May 1, 2002

By C. Sideco

"Concentrate drying at the Sullivan Concentrator goes back to 1937 when the original coal-fired dryer was put into operation. This was a second hand 8' dia. x 56' long Struthers-Wells rotary dryer that came from the phosphate plant in Warfield, B.C.In 1962, replacement of the old dryer was seriously considered. The shell and the auxiliary drive mechanism were badly worn and needed replacing. In April 1963, the new 8' dia. x 65' long fuel oil-fired Struthers-Wells dryer went in operation at an installed cost of $174,000.In 1965, it was apparent that a major rebuilding of the dust collecting system would have to be done. A study was carried out and a Ducon Dynamic Gas Scrubber was installed. The system went in operation in November 1966 and has fully met expectations.In the same year, the zinc dryer was converted from fuel oil to natural gas. The conversion has resulted in savings in fuel cost of 12 to 15%.Frame No. 1Zinc Dryer PerformanceDryer Make - Struthers-WellsDryer Size 3/4 8' dia. x 65' long Drum Drive - 100 HPSpeed of Rotation - 5 RPMFeed Rate - 50-65 TPHFeed Moisture - 10-12%Discharge Moisture - 4-6%Dryer Inlet Temperature - 1600-1800°F Dryer Outlet Temperature - 200-250°F Stack Gas Volume - 25,000-40,000 CFNDust Collecting Efficiency - 99.75-99.98% Duet Loss in Stack - 50-300 lbs./day"

Jan 1, 1972

By Wayne F. Luinstra, Frédérique Vincent, André R. Laplante

"A test to determine the amount of gravity recoverable gold (GRG) in an ore is described. Typical GRG results are given; possible uses are discussed. A case study of how the technology was used at Hemlo Gold Mines is presented.IntroductionUsing gravity to supplement either flotation or cyanidation is a well established practice in the gold industry. It differs from most recovery circuits in that most of the gold recovered by gravity would be recovered in any case by the circuit downstream, be it flotation or cyanidation. The economic justification of gravity is therefore based on small margins (for example. a net smelter return of gravity gold of 99%, as opposed to 94% by flotation). It was easily demonstrated when either flotation or cyanidation were relatively inefficient processes, and labour costs low (as gravity can be labour intensive). Over the past thirty years, the advent of better flotation machines (flash, column, high capacity), more effective collectors, and better control systems has increased flotation's metallurgical performance, thereby decreasing the incentive for gravity recovery. Cyanidation technology has undergone similar changes, with the advent of activated carbon, oxygen and lead nitrate addition, and improved impeller design.Today, gravity could remain an attractive option only inasmuch as it can be implemented with very low capital and operating costs. This has resulted in a relative shift away from gold gravity recovery (except for alluvial deposits), in the seventies and eighties. For example, as of the early nineties, gold gravity recovery has disappeared from the typical South African flow sheet. The advent of the Knelson Concentrator, at the beginning of the eighties, foreshadowed a resurgence of gravity recovery, as gold's grinding and classification behaviour (Banisi, Laplante and Marois, 1991) makes it possible to achieve adequate gold recoveries with very simple, Knelson based, gravity circuits (Laplante et al., 1994).Consider for example the Hemlo recovery circuit, made of a single 61 cm x 122 cm (2' x 4') screen, an automated 76 cm (30"") Knelson feeding a Gemeni table, to produce a 70-80% Au concentrate which accounts for approximately one fourth of the gold production (about 3 million grams per year). The low capital and operating costs make it possible to justify the gravity circuit on the basis of savings in other operating costs (e.g. fewer carbon stripping and reactivation cycles). Any improvements in recovery, which would at Hemlo be difficult to measure, would be additional benefits. Such a circuit is rapidly becoming a standard in Canadian and Australian operations.The justification for installing a gravity circuit must be first based on an estimate of how much gold it will recover (irrespective of what the potential benefits are). This is a function of the nature of the gravity circuit to be installed; however, Knelson circuits, by their very simplicity and efficiency, limit the options. This leaves the amenability of the ore to gravity recovery as the single most important parameter. Various approaches can be used to characterize this response (Woodcock, 1993). The present work sought a route which would fulfil the following criteria:"

Jan 1, 1996

By I. Filzwieser, M. B. Hanel, A. Filzwieser

The paper describes the current density increase within the last 150 years. From the beginning in 1885 at 30 A/m² up to the highest used current densities nowadays at 420 A/m² towards future pathways were even 1000 A/m² can be achievable. A short tour through history will highlight the milestones of the process of electrolytic refining of copper. Besides the improvement of the existing technology, the biggest changes leading to higher possible current densities are linked to the introduction of the ISA stainless steel plates and the introduction of the parallel flow principle. Furthermore, the parameters influencing the limitations regarding current density and therefore the practical used current density as well as the influence from the chemical composition of the electrolyte is discussed. Finally, the possibility of further increasing the current densities by enhancing the relative movement between electrolyte and electrode will give an outlook about the future of the copper electrolysis process. INTRODUCTION The current density is the most important characteristic to describe the productivity of a copper refining electrolysis besides the characteristic number for the electrical efficiency. Over the last 150 years, current density has risen from a few amperes per square meter to over 400 A/m² without any significant change in the principle of electrolytic refining. This increase in current density is documented exemplary by the electrolysis of Montanwerke Brixlegg in Austria (Brixlegg, 1963, 2013). The very beginning of the technology of electrolytic refining of copper was first patented in England by James Elkington in 1865 and the first electrolytic copper refinery was built in Newark, New Jersey, in 1883 (Armstrong, 1999). The secondary smelter Montanwerke Brixlegg, Austria, has been operating an electrolysis plant since 1884. In 1988, the third "Mount Isa" electrolysis plant worldwide and the first in Europe was put into operation in Brixlegg. Since 2010, the so-called high-current electrolysis (parallel flow METTOP-BRX Technology) with a current density of approx. 400 A/m² has been operated in half of the electrolysis process.

Jan 1, 2019

By So-Yeong Lee, Moosang Lee, Seung Hwan Ahn, Ho-Sang Sohn, Jongshin Chang

It is necessary to understand the characteristics, phase changes and chemical reactions of flue dusts introduced from a furnace to an off-gas line in order to achieve the stable operation and the improvement. This study is to develop the dust reaction model for chemical reactions of dusts in an uptake shaft of smelting furnace and a waste heat boiler. Phase equilibria and reaction paths in this system were determined by thermodynamic calculation with experimental and industrial data. The oxidation reaction rate of dusts was determined by the gas film mass transfer controlling. And the sulfation reaction rate was evaluated by the unreacted shrinking core model. Kinetic parameters were estimated by reference data including industrial ones. The present study with the developed model shows various effects of temperatures, dust particle sizes, and O2 gas partial pressures on dust reactions. INTRODUCTION The flue dusts from a copper smelting furnace move along a furnace off-gas stream into an uptake shaft and a waste heat boiler (WHB) and electrostatic precipitator(s). It is necessary to control the dust quality in order to stabilize the operation because the sticking behaviors differ depending on the phase of dusts. Phase changes of dusts are caused by chemical reactions at given conditions such as temperature and partial pressure of gases. Therefore, it is required to understand the phase changes and chemical reactions of dusts in order to perform the improvement and stable operation. The present study carried out the investigation to understand their fundamental knowledge. Especially, this study was focused on the kinetics of chemical reactions of flue dusts, developed the model. In particular, the scope of development and utilization of the model was defined as the uptake shaft of the Mitsubishi S furnace and the S-WHB radiation section in the Onsan smelter. Information needed for the modeling work referred to data from these processes.

Jan 1, 2019

By Terry McNulty

"Previous papers (McNulty 1998 and 2004) have dealt with the causes of successful and less successful achievement of design production rate by new processing plants in the minerals industry. Examination of many case histories has allowed the construction of curves or profiles that represent projects with similar characteristics that equate to differing degrees of care exercised during the project development phase. Simplistically, decreasing care is reflected by increasing risk and a heightened likelihood of poor technical and/or financial performance.This contribution provides an update, including recent case histories, and presents a modified Series 1A curve that includes the best 23 case histories, out of a total of 81 examined, or 28%. This is done to show that some very carefully developed and executed projects can ramp-up quickly and that owners of new projects should avoid being too pessimistic in projecting early cash flow if they are certain that they have done their homework. The role of metallurgical process development in the reduction of project risk is discussed and several financial analyses are presented that express the potential monetary value of a well-designed and professionally executed metallurgical program."

Jan 1, 2014

By Robert J. McCarthy

Mining has a record of achievement in developing and adopting new technology to facilitate the extraction of increasingly challenging resources. Certainly larger, or more capable, mining equipment has allowed mining companies to mine mineral deposits at lower unit costs; however, there has also been the advent of computerized systems that aid in the management and tracking of mining operations. Unfortunately, the latter computerized systems have not always had the success anticipated with their implementation. This paper explores the view that increased transparency of the planning and operating cycle in a mine, as provided by certain computerized systems, can result in some resistance from those whose work becomes ?exposed?. Examples are drawn from industry-leading technologies for both mine management and reconciliation that illustrate the issues and challenges that result. The adoption of appropriate change management principles is suggested as a best practice in planning and mitigating the challenges in implementing technologies which increase transparency in the mining environment.

May 1, 2011

By T. Krumins, L. Zunti, R. Frischmuth

Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals, in high-temperature operations. In a vent application, titanium ignition risk is reduced by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature conditions and therefore titanium ignition risk is dependent on standard operating procedures, and process control interlocks and permissive conditions. It is not uncommon for standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions.

Jan 1, 2014

By A. B. Luz, A. Middea

Kaolin clay is heavily used in the paper industry as a coating and a filler, however to attend the specifications required by the industry it has to be processed. Kaolin is also used as a filler and pigment in various materials, such as paint, plastic, rubber etc. Some crude kaolins as mined in Northern Brazil, contain colored impurities such as iron oxide and rutile/anatase. These minerals normally are stained by iron and as a result vary from yellow to dark brown in color. The kaolin beneficiation process used in that region consists mainly of degritting, fractionation by centrifuge, high gradient magnetic separation, bleaching with sodium dithionite, filtering and drying. In some kaolin clays from that region, titanium oxide mineral occurs in fine fraction, lower than 2 µm, and so making the industrial process more difficult. The conventional method of classification and bleaching with sodium dithionite, markedly improves kaolin brightness, but has little effect on anatase removal. In fact, the fine fractions resulting from centrifugation, in many cases contain more TiO2 minerals than the original whole clay or the coarse fraction. The present work is related to purification of Brasilian kaolin clay using selective flocculation for removing its colored impurities such as rutile and anatase. This study was conducted in bench scale and it consisted of: blunging, screening, conditioning and decantation. Overflow and underflow resulting from settling of the flocculated material were then dried and submitted to TiO2 and brightness analyses. Sodium polyacrylate and sodium silicate were added to kaolin clay suspension as dispersant and ammonium hydroxide was also added to adjust pH. After degritting, the minus 44 µm fraction was conditioned with hydroxamate surfactant and then polymers of different anionic charge were added. The influence of pH and type of polymer on efficiency of TiO2 removal, as well as kaolin mass recovery were studied. The results obtained in the present study are quite promising. It was possible to diminish TiO2 content and increase kaolin brightness (ISO) from 82 to 88%.

Jan 1, 2004

By Patrick Chabot

Ce document présente une méthode hybride de long trou favorisant une méthode de minage initiale par chambre-magasin et complétée par une méthode de minage long trou. Cette méthode a été adaptée suite à plusieurs facteurs tels qu?une géologie complexe, une rareté de mineur d?expérience et un haut taux de roulement de main d?oeuvre spécialisée. Cette méthode a permis d'excellents résultats par rapport à la dilution. De plus, la récupération de pilier à haute teneur par forage long trou sera expliquée. Cette méthode permet aussi de récupérer le minerai qui est resté accroché dans les chantiers chambre-magasins. Introduction : La mine Géant Dormant est une mine filonienne d?or située à environ 80km au nord de la ville d?Amos au Québec. Elle est en opération depuis 1988 et à la fin de 2007, elle a produit près de 885 000 onces d?or à partir d?environ 2 400 000 tonnes de minerai pour une teneur moyenne d?environ 11,5g /t Au. Cette mine est la propriété d?IAMGOLD Corporation depuis l?acquisition de Cambior par cette dernière au mois de novembre 2006. Elle emploie 151 employés permanents et environ 41 entrepreneurs.

Feb 1, 2008

By H. E. Johnston

There are currently a number of options in terms of plant feed comminution tests: Bond work index tests, JK drop weight and SMC tests, SPI, low impact crusher work index tests, to name a few. However, information regarding specific energy requirements for regrind mills is often requested, which can be difficult or very expensive when only a small mass of concentrate is produced from bench-scale flotation tests. This research was aimed at developing a test methodology that would produce a similar result as an IsaMill Signature Plot but require less sample mass allowing for preliminary estimates of regrinding power at a lower cost. Initially, the laboratory test methodology was completed on a single sample in comparison to the IsaMill Signature Plot for that sample. Results indicated a very good correlation between the laboratory tests and the IsaMill Signature Plot for this sample, though some parameters did impact laboratory regrind mill efficiency. The developed methodology is subsequently being applied to a range of concentrates, investigating a range of material particle sizes and material types, in comparison to a full IsaMill Signature Plot on the same sample. This new test procedure has been called ‘The Eliason Test’.

Jan 1, 2014

By Mark Richards

Highland Valley Copper is a large, open-pit copper mine in the southern interior of British Columbia. Reclamation has been in progress on the site since 1987. Some 6,300 hectares will have been disturbed at the end of the mine?s life, the majority of which will eventually be reclaimed. The establishment of vegetation and the development of a self-sustaining vegetative cover are the central components of the mine?s reclamation plan. The present vegetation-monitoring program for the reclaimed area represents a significant commitment of resources and only addresses a small portion of the site each year. In an effort to expand the area surveyed while improving the efficiency of the monitoring, the use of remote sensing is being investigated. Airborne multispectral imagery was acquired in the summer of 2001, and the results of the multispectral classification were compared to ground observations made during the routine 2000 and 2001 monitoring program. A thematic map with 17 vegetation classes was produced. Within the vegetation classes, there was a strong spectral separation between ? dry grasses? and ?legumes? with further separation according to their density. Green biomass could also be quantified remotely across a wide variety of vegetation types. During summer 2002, further aerial imagery was acquired in combination with a targeted ground-truthing program to determine characteristic vegetation types associated with recognized spectral signatures, which can be used in a supervised classification. It is anticipated that after some fine-tuning, it will be possible to shift the ground-sampling effort from areas where the aerial classification confidence is high to more complex areas.

May 1, 2003

By R. P. Viljoen, A. L. Sokolov

"The distribution of mineralized provinces is analyzed on the basis of their genetic link with specific blocks of the earth's crust including ancient platforms, mobile belts and zones of tectonicmagmatic activation. Mobile and fold belts surround the Siberian platform in Russia and the Kaapvaal craton in South Africa, with decreasing age zoning away from ancient platform margins. The main differences in the geological development of the two cratonic areas are: (1) the long period before the final stabilization of the Siberian platform (3600 Ma to 1600 Ma) and the comparatively short period of time for the stabilization of the Kaapvaal craton (3600 Ma to 3050 Ma) and (2) the intensive multiple activation of the marginal zones of the Siberian platform and the tectonicallycontrolled, magmatic sedimentary, intracratonic activity, typical of the Kaapvaal craton. Mineralization of the Siberian platform is largely characterized by marginal reactivation zones of differing ages although mineralized intracratonic Cu-bearing basins of Proterozoic age are also known. Mineralization of the Kaapvaal craton is mainly related to the formation of the intracratonic basins i.e., Witwatersrand (Au, U) and Transvaal (Au). The latter is characterized by multi-age volcanic-intrusive activity including the emplacement of Bushveld Complex (Cu, Ni, Pt, Cr, Au, V). The Siberian platform is characterized by the prolonged development of inherited mineralization from Archean until the late Mesozoic. The main period of mineralization in the Kaapvaal craton is restricted to the middle Proterozoic.The Baykal-Patomskaya and Namaqua-Natal mobile zones occupy similar positions adjacent to the Siberian and Kaapvaal cratons, respectively, and demonstrate similar modes of metallogenic development: i.e., the early formation of exhalative Pb-Zn-Cu deposits during the early stage and magmatic Cu deposits during the late stage. The more remote mobile belt near the Siberian platform, the Trans-Baykal, is characterized by intensive multi-age mineralization (Wo, Mo, Sn, fluorite), related to a period of tectonic-magmatic activation. The Saldania Belt occupies a similar position near the Kaapvaal craton but is known for its poor Au, and Cu mineralization. It does, however, have some similarities with Trans-Baykal Belt in regard to Mo-W bearing granitoids.The phenomenon of interference of geosynclinal, orogenic, platform, and tectono-magmatic activation regimes is known for the Russian section of the Pacific Ocean Volcanic Belt."

Jan 1, 1994

By J. S. Scott

"The Quemont property comprises 640 acres lying directly north of and adjoining the Noranda (Horne) mine. During 1926 to 1928, United Verde Extension Mining Corporation sank a shaft 235 feet and did 3,000 feet of development work on the 215-foot level. Between 1929 and 1930, Quemonr Mining Corporation deepened the shaft to 926 feet, and did further lateral work and drilling on the 500- and 900-foot levels. This work was confined to an area close to the south boundary and met with little encouragement.Following a period of idleness a magnetic survey was made in the winter of 1944, followed in the summer of the same year by some 6,000 feet of drilling. The first successful hole was drilled in February, 1945, from the ice of Osisko lake.To the time of writing, 131,000 feet of drilling, surface and underground,have indicated a large tonnage of gold-silver-copper-zinc ore, and although some knowledge of the geology and structure is emerging, it is too early to draw definite conclusions. The following brief description deals only with those structural features that are reasonably well indicated."

Jan 1, 1954

By P. Fellner, A. Sýkorová, J. Thonstad, J. Jurišová, V. Khandl

Adsorption of S02 on alumina used in the aluminium industry, so-called smelter grade alumina, was studied in the temperature range 15 C-120 C. The specific surface area of the smelter grade alumina was 88 m2/g. It was found that at temperatures lower than 40 C, sulphur dioxide is bonded to alumina reversibly by physical forces, and the adsorption can be described satisfactorily by the Langmuir adsorption isotherm. The heat of adsorption was estimated to be -33 kJ.mor1. At temperatures in the range 80 C- 120 C, which prevail in dry scrubbers in the aluminium industry, the heat of adsorption was determined to be -56 kJ.mor1. When S02 was adsorbed at temperatures higher than 80 C, about 30 % of the S02 could not be desorbed when heating the samples up to 250 C. In the presence of S02 and oxygen, the formation of sulphate was determined at temperatures above 90 C.

Jan 1, 2006

By M. B. McClenaghan

"The Ontario Geological Survey completed a regional till sampling project between 1984 and 1988 in the Black River Matheson (BRiM) area of northeastern Ontario. The project was designed to aid mineral exploration in the area by documenting the Quaternary stratigraphy and by providing a database of till geochemistry. This paper summarizes the results from the sonic overburden drilling component of the BRiM project carried out in areas of thick drift (> 5 m). Results from till sampling in areas of thinner drift (<5 m) have been presented in a separate paper. Approximately 1100 till samples were collected from 225 sonic drill holes. For each sample, the non-magnetic heavy mineral (>3.3 S.G.) and fine (-250 mesh) till fractions were analyzed geochemically and visible gold grains were recovered by panning.Gold and other multielement geochemical data were plotted using proportional symbols to highlight anomalous areas and to demonstrate how to evaluate and interpret a very large geochemical dataset. Thresholds for identifying anomalous concentrations of Au in till samples, defined using the 95th percentile, are 1500 ppb and 12 ppb for the heavy mineral and fine fractions, respectively. The heavy mineral fraction of older ti1ls and to a lesser extent, Matheson Till, display a number of significant gold anomalies in the study area, which in a few cases, are associated with base metal anomalies. The vertical position of gold anomalies in Matheson and older ti1ls varies from directly on bedrock to several meters above the bedrock surface and can provide information of relative ice transport distances."

Jan 1, 1994

By D. R. Schmitt, Q. Jia, R. Kofman

"Tests were carried out on clear glass blocks containing borehole aligned with and at an angle to applied principal stress states in order to study the growth of drilling induced tensile fractures. The samples were illuminated such that photoelastic fringes could be video recorded during the measurements; this was useful in assessing states of stress and in determining fracture initiation. Axial drilling induced fractures were observed at the azimuths of the applied uniaxial stress as would be expected from the concentrated stresses. En echelon fractures were observed from the borehole deviated at 45° to the direction of the compression. These preliminary and currently qualitative results show that glass blocks serve as a useful test medium for studies of stress concentration and drilling induced fracture creation. INTRODUCTIONWith the increasing exploitation of unconventional oil/gas reservoirs using deviated drilling in recent years, the effects of the in-situ stress on the success of energy production have become more critical than ever before. Knowledge of the state of stress in the earth enables us to determine well trajectories, well locations, hydraulic fracturing design and production rates, but knowing the crustal stress is always challenging. Strictly, it can only be obtained to varying quantitative degrees by accessing the earth through drilling. Failure of the rock at the borehole wall produces borehole breakouts (e.g., Bell & Gough, 1979; Haimson & Herrick, 1986; Zoback et al., 1985) and drilling-induced tensile fractures (DITF) (e.g., Aadnoy, 1990; Aadnoy & Bell, 1998; Barton et al., 1997; Brudy & Zoback, 1999; Davatzes & Hickman, 2010; Peska & Zoback, 1995). Thus, it is important to understand the failure mechanism of the rock in the vicinity of the borehole. A number of closed-form expressions have been developed that allow the stress concentrations to be calculated in the vicinity of a borehole including Kirsch’s (1898) 2-D plane strain solution and 3D formulae for elastically isotropic (Hiramatsu and Oka, 1962) and anisotropic (Lekhnitskii, 1981; Amadei, 1983) continua. These solutions have been applied in numerous studies (e.g., Ong, 1994; Ong & Roegiers, 1996; Vahid & Ghassemi, 2011; Jia & Schmitt, 2014; Ito et al., 2001) to analyze the failure mechanisms of drilling-induced tensile fractures (DITF) on the borehole wall."

Jan 1, 2015

By D. Kalumba, S. Jjuuko

"Thin Spray-on Liners resist relative small deformations (< 1 mm) between rock blocks or fragments in terms of a combination of shear, adhesive and tensile-bond strengths. Shear-bond strength addresses the ability of a thin liner to resist stresses that act parallel to the rock-liner interface. Therefore quantification of shear-bond strength is essential in the formulation of design standards and requirements for Thin Spray-on Liners. In this paper Thin Spray-on Liner support mechanisms are reviewed. In addition previous methods of Thin Spray-on Liner shear-bond testing are discussed. The paper also explains the research being carried out at the University of Cape Town to investigate the effect of different parameters on the shear-bond strength.INTRODUCTIONRock surface support is widely used to combat rockfalls and resulting injuries and fatalities in the vicinity of active faces (Potvin, 2002), where workers spend most of their time (Adams & Baker, 2002; Potvin, 2002; Lacerda, 2004). The conventional (traditional) surface support systems in underground rock support include passive methods such as mesh and lacing and active methods such as shotcrete. However, rockfall sources between 1990 and 2000 in Nevada gold mines showed a steady increase in rockfall injury associated with mesh support as shown in Figure 1 (Lacerda, 2004). The conventional methods also negatively impact the mining operations with regards to costs, logistics and mining cycle times due to large material volumes (Tannant, 2001; Ozturk & Tannant, 2010; Ferreira, 2012). Therefore, these systems need to be substituted, with enhanced methods, in order to realize the business target of the mining industry of providing the planned return on investment made without harm and within budget."

Jan 1, 2015

By C. C. Allen, H. H. North

"The Young-Davidson mine is in the southeastern part of Powell township, in the district of Matachewan. It is 32 miles southwest of Kirkland Lake, 48 miles southeast of Timmins, and 25 miles by road Northwest of Elk Lake. The Young-Davidson and its neighbour, the Matachewan Consolidated mine, are the two present producing properties in the district. The Matachewan area is the southwestern extension of the Kirkland Lake belt or 'break'. The Young-Davidson mine since coming into production in 1934 has been operated by Hollinger Consolidated Gold Mines, Limited. ""Desultory prospecting(1) has been carried on in the Matachewan area from time to time since the discovery in 1906 of silver in James township at Elk Lake, and some gold has been found in the southeastern part of Alma township and in the central part of Cairo township. The first real interest in the area, however, was started by Jake Davidson's discovery in 1916 of gold on Davidson creek, on what is now part of the Young-Davidson property, and by Sam Otisse's discovery shortly afterwards on claims a short distance to the east, now part of the Matachewan Consolidated property. In subsequent years both of these properties were investigated by various companies; the Young-Davidson chiefly by the Porcupine Gold fields Development and Finance Company, Limited, and the Matachewan Canadian by the Colorado-Ontario Development Company, Limited, which in 1919 was reorganized under the name of Matachewan Gold Mines, Limited. Work was discontinued as the ore was considered too low in grade to be mined"". However, in 1933 Hollinger Consolidated Gold Mines, Limited, undertook to bring the property into production and this became a reality in 1934.The total production to the end of year 1945 was 319,185.59 oz. gold and 73,541.94 oz. silver from 3,228,845 tons of ore. This represents an average grade of $3.67, including exchange and premiums."

Jan 1, 1954

By Esau Arinaitwe

The most extensively used methods and approaches for characterizing and selecting frothers for plant application are based on measurements in clean water in the absence of solids and without consideration of physicochemical factors that are known to influence the properties and behavior of practical flotation froths, and hence metallurgical performance. These factors include aquatic chemistry, collectors, modifiers, particle shape and size, and pH. Understanding interactions between these factors and the role and relevance that they play in characterizing frothers and froth zone properties will greatly aid in the frother selection and evaluation process. Such an understanding will also greatly enhance the ability to create frother solutions that are sufficiently robust to plant variability (such as mineralogical, comminution, operational, physical and chemical). This paper reports results of a “systems approach” study designed to probe ways in which physicochemical factors a) influence frothing and bubble size in 2- and 3-phase systems, and b) confound correlation of fundamental measurements with flotation outcome. The concepts and insights gleaned from fundamental frother studies, together with empirical laboratory flotation tests and a thorough understanding of plant needs and challenges were used to develop and implement customized frother formulation at a Cu-Mo flotation plant. Plant metallurgical data and qualitative assessment of froth zone properties showed that a frother formulation developed using the approach described here provided marked improvements in froth characteristics (mineralization, mobility, stability, persistence). These improvements resulted in better circuit control and significant performance advantages, such as improved coarse particle recovery, without detrimental downstream effects. INTRODUCTION Successful recovery of value minerals of sufficient grade via the flotation process requires selective manipulation of the value minerals to render them hydrophobic using collectors and modifiers. The hydrophobized minerals then attach to air bubbles and the mineral-bubble aggregates are selectively transported through the froth zone into the launder. Frothers play a critical role in froth formation and more importantly in achieving and maintaining desirable froth characteristics (for example, stability, mobility, persistence) that are essential in facilitating the selective transport and recovery of value minerals. Fundamentally, frothers contribute to the transient stability of thin liquid films and so aid in reducing bubble coalescence rates in the pulp and froth zones, thus maintaining the small bubbles required for efficient bubble-particle attachment. Invariably, the action of frothers at the liquid/gas interface in the pulp and froth zones impacts bubble stability, water and solids transport to the froth, which in turn impacts froth mobility, froth carrying capacity, and the concentrate grade. Consequently, selection and evaluation of frothers for flotation plants requires careful consideration of the frother type, though the choice is limited to only two main classes of compounds in terms of fundamental chemistry (short chain alcohols and polyglycols). Even with the selection of what is thought to be the best frother for a given application, practical knowledge of the froth zone and experience in controlling its properties is essential for maximizing metallurgical performance.

Jan 1, 2019