Search Documents

By É. Poulin, J. Bouchard, E. M. Pérez-García

Process control and optimization have always been crucial aspects in the mineral processing industry, and expectations constantly increase to cope with more stringent security, quality, efficiency, and environmental performances. The main challenges to reduce variability of key process variables, and steer profits to higher values while maintaining sustainability indexes within acceptable ranges come from nonlinear responses and circulating loads. The most commonly implemented control strategies rely on simple PID controllers for practical implementation and maintenance considerations. If arguably good performances are accomplished when these are adequately set up, there is also room for further gains by using more advanced methods such as model-based techniques. There is thus a need for more realistic process and equipment models. Based on advances of the past few decades, this paper introduces an autogenous/semi-autogenous mill (AG/SAG) model to be included in a modular comminution circuit simulation toolbox comprising ball/rod mills, material handling, and classification devices. The proposed mill model incorporates a modified version of the classic comminution equation that makes grinding rates proportional to the energy input. It requires the determination of a selection function (fragmentation rates) and a breaking function (fragments distribution). The former is modelled with an S-shaped curve characteristic of AG/SAG processes and the latter is a size-relative distribution of the produced fragments. The power draw is predicted employing the empirical equation of Austin. The paper also develops a case study to illustrate how the proposed simulation framework can capture the behaviour of an actual plant. Model calibration consists in an optimization problem that search the global minimum of the difference between predicted and measured/estimated size distributions, power draw, solid fractions, etc. Results demonstrate that the mill simulator can mimic an actual process in its operation conditions. INTRODUCTION Comminution is a key stage in the mineral processing industry, obviously because the phases of interest must be liberated to be able to recover them. In general terms, the global performance of a plant depends largely on the efficiency of the grinding circuit and on the material properties such as its grindability, density, and mineral grades. The subject has vastly been studied since as early as the 19th century, when Rittinger (1867) and Kick (1883) developed some of the first empirical models to relate grinding and energy input. The great interest in the subject comes from the fact that this operation is costly and, probably most concerning, highly inefficient. Buckingham et al. (2011) estimated that ore comminution can represent up to 60% of the overall plant power draw. Moreover, only a modest fraction of the power draw effectively translates into rock fragmentation. For grinding, estimates range between 1% and 25%, depending on the reference used, while the rest is mainly lost as heath (Fuerstenau & Abouzeid, 2002; Tromans & Meech, 2002; Bouchard et al., 2017).

Jan 1, 2019

By F. S. Su, P. Z. Pan, X. T. Feng, F. Yan, W. W. Ji

"This paper aims to simulate the spalling failure behavior in hard rock based on a self-developed numerical model, i.e. a rock discontinuous cellular automaton (RDCA). A crack initiation and propagation criterion is proposed based on the plastic strain, which is used to link the continuity and discontinuity during the failure process. The discontinuities of rock, such as cracks and other internal boundaries, are represented by discontinuous displacement functions, i.e. tip enrichment and step enrichment. The partition of unity is used to improve integral precision of the elements intersected internal boundaries, which is traced by a level set method. Arbitrary crack geometries can be conveniently represented and it does not require any remeshing in the modeling of crack initiation, propagation and coalescence. Numerical modeling of excavation in hard rock using RDCA is conducted. The spalling failure process of hard rock induced by excavation is well simulated. The depth and shape of hard rock spalling failure are good agreement with in situ observation.INTRODUCTIONThe excavation in rock mass is more and more popular. At the same time, the disasters, such as rock burst, rock spalling and falling etc, induced by excavation are quite prominent. Numerical modeling is an important way to help us understand the failure mechanism of rocks. Many numerical methods have been used to simulate the excavation of rock mass. For example, the finite element method (FEM) (Karakus and Fowell, 2003), the discrete element method (DEM)(Cundall and Strack, 1979, Labra et al., 2008), Finite difference method (FDM)(Zhu et al., 2009), Element Free Galerkin Method (Belytschko et al., 1994), Discontinuous displacement analysis (DDA) (Shi, 1988) and Boundary element method (BEM) (Katsikadelis, 2002, Chen and Hong, 1992) are commonly found in the stability analysis of excavation in rocks. In the modeling of crack propagation or excavation, most of these methods are tedious since the internal boundaries have to be consistent with the element boundaries. And in many cases, the remesh has to be conducted. In recent years, people are interested in particular types of FEMs, such as the extended finite-element method (XFEM), the particle discretization scheme finite-element method(PDS-FEM(Hori et al., 2005, Oguni et al., 2009)), the combined finite-discrete element method (FEM/DEM) (Munjiza and Wiley, 2004, Cai, 2008) and spectral-element method(Gharti et al., 2012) etc."

Jan 1, 2015

By Engin Burak Anil

Objective, accurate, and fast assessment of damage to buildings after an earthquake is crucial for timely remediation of material losses and safety of occupants of buildings. Laser scanners are promising sensors for collecting geometrical data regarding the damaged states of buildings, as they are able to provide high coverage and accuracy at long ranges. Yet, we have limited knowledge on the performance of laser scanners for detecting earthquake damage, and requirements of such data collection. This paper focuses on characterizing the performance of laser scanners for detecting thin cracks for damage assessment of reinforced concrete frames. We identified a series of crack parameters based on the state-of-the-art damage assessment codes and standards. Similarly, we identified parameters, which affect the performance of laser scanners for detecting cracks, based on prior research in this area. We studied the width, depth, and orientation of cracks; sampling interval of the scanner, and the range of the laser beam from the surface. Effects of these parameters on the detection of the minimum crack size were determined in an experimental setting. An automated algorithm was used to analyze the data. The results show that it is possible to detect as small as ~1mm cracks.

Aug 1, 2013

By A Smirnov

The problem of thin and very thin coal seam extraction is examined in a long perspective of Ukraine?s fuel and energy industry development. The technical and economic benefits of the coal seam selective mining technique are described, including beneficial environmental impact.

Aug 1, 2013

By Robert B. Parsons

"The Province of Manitoba tabled a Budget on March 11, 1992, which contains some important new initiatives designed to improve the fiscal environment for mining in the province. In addition, the Minister of Energy and Mines has released details of the Mineral Exploration Incentive Program which was originally announced in the 1991 Budget.Introduction""We recognize the important contribution o f mining to the economic activity of our province, including direct and service jobs and export earnings. We are determined to secure its future."" - The Honourable Clayton Manness, Minister of Finance, Province of Manitoba, March 11, 1992.With these words of introduction, Manitoba Finance Minister Clayton Manness announced a number of significant measures aimed at improving the fiscal regime for exploration and mining in Manitoba. At the same time, details of the Manitoba Mineral Exploration Incentive Program (MEIP) were released."

Jan 1, 1992

By C. B. Ndimande, C. Ntsele, M. Lisso, L. Arlow

"In the processing of UG2 platinum ore, stirred milling technologies are dominating regrind applications that require grinding the particles to P80s’ in the region of 45 µm. For this application stirred mills are 30–40% more energy efficient and require a smaller foot print compared to traditional tumbling mills. In this work a study was carried out using a batch pin mill and three scales of Stirred Media Detritors. A laboratory scale pin mill, a pilot scale Stirred Media Detritor with an installed power of 18.5 KW and two industrial scale Stirred Media Detritors in continuous operation, with an installed power of 355 KW and 1,100 KW were used. The industrial scale SMDs were in the secondary grinding section of a mill floatmill float (MF2) UG2 processing plants. The tests were focused on assessing the effect of feed rate and percent solids on power consumption and product fineness at lab scale, floatation response of the SMD product at pilot scale and on an industrial scale, the effect of feed rate on energy consumption and product fineness. The measurements obtained were feed flow rates, mill power and from the samples cut, particle size distribution of both feed and product. Specific energy was observed to increase with increasing percent solids over the 30wt% to 80wt% studied. Floatation response tests of the pilot scale SMD products show improvement in grade. Specific energy and reduction rations are observed to decrease with an increase in feed rate.INTRODUCTIONThe purpose of comminution in most mineral processing applications is to liberate the valuable minerals from gangue so that they can be recovered in subsequent separation stages. Most precious and base metal plants treat low grade fine-grained ores which require a higher degree of size reduction to yield the necessary degree of liberation (Partyka & Yan, 2007). Many authors have shown that the relationship between product size and grinding energy consumption is exponential, the finer the product from the comminution device, the higher the energy consumption (Gao & Weller 1993; Napier-Munn, Morell, Morrison & Kojovic, 1996; Jankovic, Valery & La Rosa, 2003). The suggested reason for this kind of relationship is that smaller particles have fewer flaws and higher strength than larger particles. Particles with fewer flaws and higher strength require higher energy for breakage to occur. One of the challenges most plants face is that of efficient energy utilisation in the liberation of the mineral from these complex ores. Conventional tumbling mills are not energy efficient in fine and ultra-fine grinding applications because some of the energy is spent on moving the charge and does not go directly into breakage. Stirred mills have been found to be about 30% to 40% more efficient and require a smaller foot print compared to traditional tumbling mills for regrind applications that require product size with P80s’ in the sub 45 µm regions (Radziszewski & Allen, 2013). Stirred mills are able to produce fine product because they can achieve a high number of stress events per unit time and volume compared to tumbling mills (Kwade, 1999a). To minimise energy usage without compromising product quality, the mining industry has adopted stirred milling technologies for fine and ultra-fine grinding (Radziszewski & Allen 2014; Kwade, 1999b). The south Africa platinum group metal (PGM) industry alone had over 40 stirred media mills installed by 2011 (Rule, 2011). Of that 40, 13 were in the ultra-fine grinding (UFG) application and the rest in main stream inert grinding (MIG)."

Jan 1, 2016

By John F. Vynne

This paper will discuss several of the systems and processes that have been developed over the past few years, and are now being utilized by major mining companies on draglines in North America, Australia and South Africa. These technologies include production monitors and reporting systems, GPS navigation systems, structural integrity monitoring systems, structural analysis studies to increase the dragline RSLs, and inspection and response strategies. The use of these technologies provides significant increases in dragline production, and reduces maintenance costs and downtime. The question that needs to be asked is what value is there in monitoring? Increasing dragline productivity is dependent upon to two items with the overall goal being to maximize the number of bank cubic meters moved and to uncover more coal: 1) maximizing payload and 2) maximizing the number of cycles. If you do not measure and try to optimize the parameters that impact payload and number of cycles, there is very little chance that you can improve overall dragline productivity. These parameters are: Maximizing payload is dependent upon the following: ? Geology ? Blasting ? Monitor weighing accuracy ? Engage location ? Disengage Location ? Rigging ? Suspended load ? Bucket characteristics ? Operator skills ? Minimizing rehandle Maximizing the number of cycles depends upon maximizing digging time, and minimizing cycle and delay/down times by: ? Minimizing Operational Delays ? Minimizing Mechanical Delays ? Minimizing Idle time ? Minimizing Walking time ? Minimizing Fill Time ? Minimizing Swing Angle ? Maximizing Swing & Return Rates ? Minimizing Spot Time A third reason to monitor, conduct structural analysis studies, and have inspection strategies is to prevent catastrophic failures such as shown in the following photographs (figures 1 & 2).

May 1, 2008

By Patricia Dillon

EHS Management Standards Communication and Reporting (8) ! Establish processes for internal and external communications ! Designate responsibilities for communication with COI ! Report as defined by senior management ! Report annually to employees, shareholders, COI on EHS and social performance Community Rights and Public Consultation (9) !Identify COI?s and establish process to hear concerns !Acknowledge and respond to complaints !Support local communities !Plan for closure and conduct public consultation !New projects include identification of COI?s, concerns to be considered in design

May 1, 2004

By D. Mark Richards

Highland Valley Copper is a large open pit copper mine in the southern interior of British Columbia. Machine guidance technology using the Global Positioning System (GPS), was first implemented at the mine in late 1996 for blast hole drill navigation. The purchase of a third BE49R drill in 1998 completed the change to GPS navigation for all the mine?s drilling. The acceptance of this technology was almost immediate at both the operator and management levels. With the purchase of a new P&H 2800 shovel in 1997, the opportunity was taken to extend GPS navigation to a shovel. Due to communication restrictions, this was not as successful as envisaged. In late 1999, following a cost benefit analysis, a three-shovel trial of Caterpillar?s Computer Aided Earthmoving System (CAES), was initiated. The trial was successfully concluded in June 2000 and a further two shovels were equipped. Acceptance of this system has been very good at all levels, which has undoubtedly contributed to its success. In September 2000, CAES was extended to the dozer fleet with the purchase of a new track dozer. The CAES equipped dozer is used for pit production and project work. It is planned to extend CAES to the rest of the shovel fleet in 2001, along with a production front-end loader and one or two more track dozers.

May 1, 2001

By R. T. Erskine

"IntroductionIn this paper it will not be possible to cover all details of the reagent systems at Brunswick Mining and Smelting but it is hoped that a description of the evolution of these systems will be of some benefit. The concentrator of Brunswick Mining and Smelting located near Bathurst, New Brunswick was originally designed as a 3,000 ton per day operation but before construction commenced was uprated, with 4,500 tons per day being treated by the summer of 1964. Development of the open pit at another ore body five miles away was initiated in 1965 and additional concentrator and crusher facilities went into operation in September, 1966. Present total daily throughput is over 8,000 tons per day. The ore at Brunswick is very high grade but mineralization is very fine grained and requires grinds generally over 75% minus 400 mesh for liberation. The amount of surface exposed using grinds of this order understandably requires great quantities of reagents, Reagent mixing systems for the original concentrator allowed only for batch mixing and were very expensive in labour cost especially.During the first three years of operation total number of men employed in reagent handling reached a peak of four men per shift and six men on dayshift unloading cars for a total of 22 men. At present only one man is employed on shift, and four men on dayshift take care of unloading and mixing reagents, a total of 8 men. The man on shift is almost entirely occupied with checking feeder operation, flow rates, and head tank levels. Most commonly used reagents are tabulated in Fig. 1 showing average monthly and daily requirements in the Brunswick operation as well as pounds per ton of mill feed as found in 1969. It is very obvious that with over seventeen tons each of lime and soda ash and six tons of copper sulphate used each day, opening of bags and mixing batches of solution is an inefficient undertaking."

Jan 1, 1970

By Willie Manfrey, Richard Klimpel

This paper describes the effects of slurry viscosity on the selection-for-breakage and breakage distribution parameters in the wet grinding of cres. A series of experimental tests were run on laboratory scale ball mills. Slurry viscosities were modified by varying the solids/water ratio with and without the presence of selected chemicals. Very consistent and predictable correlations are shown to exist. The grinding parameters were calculated using a computerized back -calculation technique developed by Klimpel and Austin. Industrial scale circuit calculations and preliminary plant trial data suggest that considerable increases in throughput and/or fineness of grind can he achieved through the judicious use of chemical additives.

Jan 1, 1977

By Laxman M. Amaratunga, Glen G. Hein

"Most mining operations utilize the tailings coarse fraction for backfilling while the fines have been traditionally disposed on surface in tailings ponds. Recently, paste fill has been developed which uses a fraction of the fine tailings (10-30% w/w of <45 µm) in the fill (Brummer and Moss, 1991). This development allows a mining company to use a portion of the fines for backfill, but still requires surface impoundment of the unused tailings. Reactive tailings have the added problem of generating acid after being oxidized in the presence of air and water. Treating acid mine drainage (AMO) from these ponds has proven to be a costly environmental problem and a long term liability.One practical method to reduce the environmental impacts associated with the tailings pond is to modify the physical and chemical prope1ties of the fine tailings so that they can be utilized in an environmentally safe manner. This was accomplished by agglomerating the tailings into pellets and using theses pellets as a coarse aggregate in a total tailings paste fill. This technology does not require any supplemental sand or gravel to be added to the fill.This paper presents the ongoing research into utilizing these tailings agglomerates as a coarse aggregate fraction, in order to create a total tailings paste fill which has supe1ior strength characteristics.IntroductionThe Canadian mining industry produces more than 500 million tonnes of tailings and waste rock annually. The waste rock is usually returned underground for use as rock fill in underground support with the tailings remaining to be disposed of in tailings ponds. Tailings consist of a coarse and fine fraction, and can be either reactive (acid generating) or non-reactive. In an effort to minimize tailings disposal, the coarse fraction has been used underground in backfill along with alluvial sands. This diversion of the coarse fraction, however still requires that the fine fraction be disposed of in tailings ponds. This disposal creates the potential for acid mine drainage (AMO), since in the presence of air and water, reactive sulphide tailings can generate acid. It is therefore an important goal in the mining industry to minimize the disposal of fine tailings into tailings ponds since the treatment of AMO is a costly and long-te1m environmental liability."

Jan 1, 1997

By Pierre Labrecque

Dispatch systems have been used for open pit mining since the early 1980?s but similar systems do not widely exist for underground mining. There is a need for developing dispatch systems for underground mines, particularly highly automated operations such as block caving. An innovative method, Agent Based Modeling (ABM) for a dispatch system for a block caving operation, is proposed in this paper. The model is based on a particular behaviour observed in social insects. The focus of the ABM dispatch system is adaptability with respect to changing operational conditions and effective integration of maintenance modules with the operation. The paper will show the advantages of this innovative method compared to existing similar systems. Furthermore, the preliminary approaches for developing an agent based modeling system for block caving operations are highlighted and discussed in this paper. 1. Introduction In social

May 1, 2008

By Nelson Lawrence

An Electrical Risk Management/Inspection Program has been designed specifically for the mining sector in order to provide electrical code expertise and systemic gaps in electrical systems. Goals include improved safety and productivity, reduced injuries and help to enable businesses to better comply with the electrical codes and regulations that govern them. The Electrical Risk Management/Inspection Program is now recognized by some of the world?s largest mining organizations. Since June, 2001 these electrical safety advisory services have been available to underground and surface mine sites throughout Ontario and are now offered throughout Canada and around the globe. This program is also currently being applied to review new electrical installations for mine construction projects thus improving the safety and reliability of mine site electrical systems.

May 1, 2006

By Marc Tardif

"The way alarm information is provided to an operator can make a huge difference in the minutes following an upset. Process alarms are often looked at as a way to help avoid catastrophic failure and serious accidents. But knowing that mineral processing is so energy consuming and that raw material is not consistent, all small upsets should also be seen as a catastrophe because they can have significant impact on product cost and quality.This paper will demonstrate how it is possible to use data from process alarms to provide operators with real time, value added information that will help them take the right decision at the right time and in turn, reduce unplanned downtime by 20 to 80% and incidents by up to 50% (number and cost),and optimize energy and capacity usage.In the era of Big Data, living in a world where we are submerged with information, one of the biggest challenges is to find the right information at the right time.Alarm rationalization projects will often focus on alarm quantity, but alarm quality is also very important. It is possible, by following a simple 6-step process to turn “alarms” into truly valuable information for operators. Based on known standards (ANSI/ISA 18.2 and EEMUA 191), this process will capture the knowledge of the best and most experienced operators and process engineers, and make it readily available to everyone, right on time, when it matters the most.INTRODUCTIONWhen spending some time in a modern control room, it is easy to notice the huge quantity of information that is available to the operator. Modern operation stations feature multiple screens with HD capability. These screens display information like process display, history trends, alarms and events list, maps with geo-located information, images from live cameras, etc. However, it is harder to assess whether all this information is really helping operators: Is all the information relevant? Are process screens overcrowded? Is the information easy to understand? Does the operator know what to do with all the information? Are there too many alarms?"

Jan 1, 2016

By H. W. Hughes

"The Wasamac Gold Mines mill, situated 10 miles from Rouyn-Noranda on highway 59, commenced milling April 1st 1965 at a rate of 700 tons per day. This has gradually increased to over 1200 tons per day in December. The mill has done up to 1400 tons on occasion.The ore was formed in the Wasa shear zone by means of replacement. The minerals which replaced the original rocks were carbonates, quartz, pyrite, chlorite, gold and silver. Work index varies from 9. 6 on the chlorite to 11. 6 on the quartz. The gold is very finely disseminated throughout the gangue and while associated with the pyrite is not included in the pyrite. Very seldom is gold found or seen in the free state.Test work showed a medium fine grind of 85 to 90 per cent was necessary to achieve a 95.00 per cent extraction. Straight cyanidation time of 30 to 36 hours was indicated. This has been borne out by subsequent mill performance with a grind around 87 per cent minus 200 mesh and extraction ranging from 95 to 96 per cent.When it was decided to bring the Wasamac property into production, the Bicroft Uranium Mines Ltd. crushing and grinding units together with one pebble mill and the pachuca tanks from Dyno Uranium Mines Ltd. were purchased.Wasamac crusher house and mill buildings are of laminated wood construction, covered with 5/ 8th inch plywood and corrugated iron sheeting."

Jan 1, 1966

By W. J. Witte, M. K. Witte

"INTRODUCTION A pilot heap leach project was conducted on the B. P. Selco Hope Brook ore located in southwestern Newfoundland. The pilot heap leach was undertaken to assess and confirm the following:1) To confirm that heap leach technology now currently used in the United States could be applicable to Canadian sites.2) To confirm gold recovery by the Heap Leach technology3) To assess and study potential heap leach environmental concerns in cold and wet climate.PROJECT LOCATIONThe Hope Brook Project is located near the southern coast of the island of Newfoundland, approximately 100 kilometers southeast from Stephenville, approximately 25 kilometers west of Burgeo, Newfoundland. Access to the property is limited to helicopter, float plane or by sea through Couteau Bay. The property was covered with muskeg and very few trees. Surface relief was moderate with many poorly drained boggy sections confined to small areas. Many small unnamed lakes were located on the property which provided water to small brooks and streams flowing to Couteau Bay.Several locations were reviewed for the installation of the pilot heap leach facility. Important parameters used to select a suitable location included sufficient land area, close proximity to but not on the ore body, reasonable protection from wind, sufficient supply of fresh water, close to a suitable location for a portable crushing plant, reasonable access to aggregate material for preparation of the test pad and ponds and suitable contours to minimize site preparation."

Jan 1, 1987

By Alireza Sarafi, Alijan Aftabi

"A hydrocyclic system used for mineral separation at the laboratory scale results in the separation of more than 90% of micas. The system functions only by water and might offer advantages where other methods of mica separation are not available. INTRODUCTIONVarious methods for the separation of micas, wollastonite, and garnet, e.g., screening, flotation, magnetic separation, and heavy liquids, are well known (e.g., Spence, 1929; Bates,I960; Gillson et al., 1960; Benjamin, 1971; Connor and Kolhnar, 1991; Collings and Andrews, 1991). However, where these methods are not available, the separation of micas by a hydrocyclic system developed by Sarafi and Aftabi (1991) may prove to be economic. This note is a brief description of the hydrocyclic system. Minerals and MethodFor testing the recovery of mica and other minerals from different rocks (garnet-mica schist, skarn, and pegmatite), standard minerals were tested first, and then rock samples. Pure mineral standards were prepared from coarse-grained samples of pegmatite, mica schist and skarn; the grain size of the minerals separated was more than I cm. The Hydrocyclic System and Mineral SeparationThe hydrocyclic system is shown schematically in Figure 1. In the first step in mineral separation, mineral and rock samples were crushed, milled, and then sieved to minus 250 plus 125 microns. Approximately 10 gm to 25 gm of the sample were inserted in decanter Dt • The motor pwnps, M1 and M2, were then turned on and the water valve rl was opened. At this time, water was flowing turbulently (30 em3/sec. to 50 em3/sec.) and minerals were separated according to their crystallographic nature, density and!or habit. The fInal separation was done by exit valves r2, r3 and r4, while the motor pwnps were still operating. After each experiment, the rt , r2&apos; r3 and r4 valves were closed and the motor pumps were turned off. Following this, minerals in each decanter and the mter were collected, dried and weighed. The whole time of the experiment was optimized to be about 10 minutes, but varied from 3 to 15 minutes for micas and garnets. respectively."

Jan 1, 1994

By John Keay, Douglas R. Shaw, Gregory J. Olson

"The results are presented herein of on-going laboratory investigations of heap bacterial oxidation as a pretreatment method for the recovery of sulfide-encapsulated gold from ore samples of the Rhodes Mining Lahoca deposit, located in northern Hungary. The ore contains just over 2 g Ault and as much as 6% sulfide, mostly as pyrite. Laboratory aerated column tests conducted at Colorado Minerals Research Institute (CMRI) showed that mild to moderate biooxidation of the finely crushed ore occurred rapidly in approximately three months, with cyanide gold recoveries of up to approximately 60%. The results contrast cyanide gold recoveries of less than 30% from non-pretreated ore. Mineralogical examination of biooxidized residues indicated that the mechanism of biooxidation of crushed ore was related to microorganisms following pathways along structural anomalies in the pyrite grains. Such selective biooxidation is an important result to minimize the biooxidation and aeration time and effluent neutralization costs in a commercial operation.IntroductionThis paper describes the development of a heap biooxidation process for the Lahoca gold project The Lahoca deposit is situated in northern Hungary, at the site of a former copper mining area. Lahoca is a large tonnage, relatively shallow, deposit amenable to open-pit mining Lahoca has the potential to produce I 00,000 ounces of gold annually for at least ten years at its minimum reserve base.The laboratory test work conducted initially by Rhodes Mining NL demonstrated that the Lahoca refractory ore is amenable to whole ore and concentrate oxidative pretreatment and cyanidation. Capital and operating costs, however, for such milled ore treatments were considered relatively high. Rhodes Mining subsequently evaluated heap leaching methods, particularly heap biooxidation pretreatment, as a process route that promised superior economics suitable for exploiting lower gold grade refractory ores.This paper focuses on the laboratory column (simulated-heap) biooxidation test work, particularly the proposed mechanism of selective microbial oxidation, wherein only a small amount of the sulfides are oxidized sufficient to allow commercially acceptable gold recoveries by conventional cyanide heap leaching. Selective or minimal biooxidation of sulfides is considered important to minimize biooxidation time and aeration requirements, as well as acid effluent neutralization costs."

Jan 1, 1998

By Roy EI. Durr, Glen R. Davidge

"This paper presents the results of structural analyses and full-scale destructive tests conducted on liner plate culverts. The purpose of this work was to establish a design method and evaluate the suitability of using these structures in potential roof-fall areas for a rehabilitation application in lower stress and relaxed mining environments. Field evaluation of the design is currently in progress.Theoretical ultimate resistance functions were established for two different culvert shapes and were found to be representative of their experimental behaviour. The ultimate resistance function was used to determine their plastic behaviour to a rapidly increasing deflection condition, to determine the energy absorption capacity of these structures, and to predict their response to impact loading.IntroductionThe Kidd Creek mine of Falconbridge Limited is located justnorth of Timmins, Ontario. The area under rehabilitation for which this program was developed is the 2600 level of the No. I mine. The problem of effectively securing selected drifts at the 2600 level in NO.1 mine, for access to a high-grade ore block, is key to the economics of the operation. Diamond drill test holes had indicated a loosened rock mass above the 2600 level of about 7.5 m thick in response to the extensive mining operation below this level. This level forms the arbitrary boundary between the No. I and No. 2 mines, and has extensive volumes of cemented rock fill below it and largely untouched ore above it to the 2000 level in the North orebody. The walls at that level were showing relaxed ground conditions typical of de-stress: sub-horizontal joints opening up, and peeling.Due to the ground conditions, the consequent safety risks, the high grade of the ore, the potential production delays, and the likelihood of several phases of rehabilitation, regularly used drift rehabilitation employing rock bolts, cable bolting, or shotcrete was not practical. Two options were deemed possible alternatives to suit these conditions, steel sets with blocking and lagging, and liner plate culverts with backfill. Culverts were chosen."

Jan 1, 1995