Search Documents

By A. Mcdonald

"An X-Met Analyzer was purchased from Outokumpu in late 1983for use in the Hudson Bay Mining and Smelting smelter. Its first use was in the fuming plant to give zinc assays of each charge of slag tapped from the fuming furnaces. This quickly told the operators exactly when each charge had reached its economic tap-out point, and gave supervision a fool-proof method of identifying good operation. These and other factors led to major improvements in coal utilization in the fumers and to major increases in zinc oxide production. A second unit was later purchased for the reverberatory furnace to give silica and iron assays of the slag, and these were used to make adjustments in the feed composition to maintain the desired SiO2:Fe ratio in the slag. Since purchasing the units for the furnace, the oil consumption and copper content of the slag have dropped significantly. IntroductionSmelters have lagged far behind concentrators in process control by mean s of rapid product analysis. The on-stream X-ray analyzer was developed about seventeen years ago, and soon concentrators around the world were getting assays of the incoming ore, .concentrates and tailings every fifteen minutes, and using these to control reagent additions and other process variables. Almost always, the concentrate grade and recovery improved.In smelters, product streams are solids or molten materials, not the more easily handled slurries, and until seven years ago no inexpensive equipment was available to provide rapid analysis of this type of material. In approximately 1980, several companies developed instruments based on irradiating solid samples with low-intensity gamma rays from radio-isotope sources, and measuring the secondary X-rays emitted from different elements in the sample to provide an analysis of the elements desired.The smelter staff had a close look at what was needed and listed the following points as being critical:1. ability to provide Zn assays of a sample of slag within 15 minutes of taking it, in order to achieve optimum fuming times (zinc fuming , being a batch process, had the greatest potential benefit from rapid slag analysis);2. ability to give Cu and Fe assays on the slag, and on other smelter products, such as matte and converter slag;3. ability to give Si02 assays since the SiO2 content of the slag has a strong effect on fuming rate; and4. ability to stand up to an industrial atmosphere such as exists in the fuming plant."

Jan 1, 1987

By K. E. Waters, J. E. Nesset, F. Rosenblum, J. A. Finch, S. Moon

"Some materials when exposed to various conditions can exhibit a rise in temperature without requiring an external heat source. Generally referred to as pyrophoric or self-heating substances, they challenge the safety of materials handling, storage and transportation. Reliably assessing the self-heating potential of materials is thus essential. Over the years a number of test protocols have been developed. A widely accepted method is that recommended by the United Nations to certify the safety of shipping pyrophoric goods. Our test work on sulphide materials has shown that the U.N. test can give false negatives if the sample oxidation history is not considered. Depending on the degree of oxidation (“weathering”), the same sulphide material can exhibit self-heating ranging from safe to hazardous. For concentrates, oxidation can occur during storage and transport making the sample weathering history an important consideration in the test work. To make the U.N. test, and other single-stage self-heating procedures, more reliable in assessing self-heating potential when testing sulphide materials, it is suggested that a weathering step be incorporated in the test protocol. This test work for two sulphide samples, an ore and a concentrate, demonstrates the impact of incorporating a weathering stage in the test protocol. INTRODUCTIONSelf-heating occurs when exothermic reactions produce heat faster than can be dissipated to the surroundings. Numerous substances self-heat, ranging from wood chips and powdered milk to coal and sulphide minerals (Beever & Crowhurst, 1989; Hudak, 2002). Mixtures of sulphide minerals, most notably those containing the iron sulphide pyrrhotite (Fe(1-x)S), commonly encountered in the extraction of base metals (e.g., copper, zinc, lead, and nickel), are particularly prone to self-heating (Rosenblum, Nesset, & Spira, 2001; Payant, Rosenblum, Nesset, & Finch, 2012). In the mining and subsequent processing stages, the minerals are progressively liberated and finely ground, then separated, usually by flotation, with the resulting concentrates stored and transported to smelters for metal extraction. At most of these stages the sulphides are exposed to both moisture and oxygen, conditions that promote partial sulphide oxidation and the formation of elemental sulphur. Studies have shown that pyrrhotite, in particular, readily oxidizes to form elemental sulphur (Bernier & Li, 2003; Belzile, Chen, Cai, & Li, 2004; Somot & Finch, 2010). The elemental sulphur becomes fuel for further self-heating as the temperature of the mineral mixture increases above 100 oC (Rosenblum & Spira, 1995; Somot & Finch, 2010). It is believed the propensity of pyrrhotite to self-heat is a result of its iron-deficient, and hence somewhat unstable structure. It is worth noting that pure metal sulphides (with the exception of pyrrhotite) do not exhibit appreciable self-heating. A mixture of minerals sufficiently different in their electrochemical rest potential is required to initiate self-heating at ambient temperatures (Payant et al., 2012)."

Jan 1, 2016

By D. Chakravarty, B. Samanta, D. Ghosh

Autonomous robots are useful for 3D underground mine mapping to avoid human exposure to hazardous spaces. To prepare a precise mine map, a self-navigating robot must navigate an arduous path, avoiding obstacles and sensing the environment. A prototype laboratory-scale robot was built and evaluated through a mock-up in a test mine gallery. It was outfitted with a 2D laser scanner, a stereo camera for obstacle avoidance, and a high-precision, laser-based imaging and digitizing system for collecting 3D point cloud data. Various algorithms were used for scan matching to facilitate simultaneous localization of the robot for mapping.

Jan 1, 2014

By Naizhong Xu

During the past 30 years, fully mechanized caving mining has played a positive role in the improvement of the efficiency of coal production, but which has also had a great influence on the mining environment, especially to environment damage of shallow mining areas in the central and western regions of China. The surface subsidence parameters are the basis of the surface environment evaluation and governance. During 1980~1990s of the last century in China, fully mechanized mining subsidence laws were researched more fully, however, since coal caving technology is affected by many factors, and researches on its mining subsidence laws (parameters) were found to be grossly inadequate. Through actually observed in recent years, it is considered that coal caving mining subsidence laws (parameters) can use fully mechanized mining law (parameters) for reference. Based on fully mechanized mining laws (parameters), this paper reveals the similarities and differences of the surface subsidence laws between fully mechanized caving mining and fully mechanized coal mining, which can guide the work of coal mining under buildings, water bodies and railways in new mine area and mine collapse governance.

Aug 1, 2013

By Suping Yao, Chuanyu Jiang

In the last decade, the copper industry in China has witnessed a significant change. The capacity and production of refined copper has grown remarkably from 1.5 million tons in 2002 up to 5.88 million tons in 2012. And now, China has become the biggest copper producer in the world, counting about 30% of the global refined copper production. This paper summarized modern copper smelting and converting technologies employed in China copper industry, such as OT flash technology, TSL (ISA/Ausmelt), SKS bottom blowing, Jinfeng side blowing, etc…This paper also presents some key development and improvement of these technologies up to date from their practical application in China, what will contribute as great value to any new / or renovation copper smelting projects down the road. As an engineering company in China, NERIN has been involved in many of these projects in the past decade, played an important role in the engineering works and accumulated intensive experiences. NERIN is one of the best choices for the world clients in the copper industry, providing quick engineering service, delivering cost effective projects.

Jan 1, 2014

By George A. Guess

The making of contracts for the purchase of ores is a business which the metallurgist usually understands better than the miner. Companies in the custom ore business often employ an ore buyer who is aware of the class of ore which the smelter needs, and is thoroughly conversant with the business. The miner on the other hand makes ore contracts but seldom, and it is often only after a settlement has been made that he realizes the meaning of the terms of the contract under which he has sold his ores. He has expectations usually greatly in excess of the amount 'net proceeds' shown at the bottom of the settlement sheet. Seldom does the occasional shipper really know his contract. A somewhat similar parallel is to be found in insurance policies. We all have insurance policies; we never know the conditions contained in them until after the fire. The clauses in the policy are for the protection of the Insurance Company. An Insurance Company has no friends.

Jan 1, 1926

By K. Fumimura, T. Nishimura, M. Kohno

When applying numerical techniques to problems of deformation of rocks, the body to be analyzed is divided into small portions and is represented by a system of points linked together with the neighboring points. In the so-called distinct element modeling, the particles in the system are directly connected by springs and a contact law is used to specify forces on the particles to simulate the mechanical behavior of the body. The relation between the spring stiffness and commonly measured material properties, such as the Young’s modulus and the Poisson’s ratio, should be known a priori. For the general case of a random packing of particles, the relation is found by means of a process in which a system of particles and set of parameters are prepared to simulate a set of specimen-size test and then the input parameters are chosen to match the measured material properties. The validity of the numerical result is only demonstrated by comparison model behaviors with the measured responses. The process includes trial-and-error manner, therefore, no model is complete to reproduce the mechanical properties. In this paper, a relation between the spring stiffness and the elastic constants; the Young’s modulus and the Poisson’s ratio, is introduced to a three-dimensional distinct lattice spring method. Two simple numerical examples will be presented to demonstrate the performance of the method with the procedure for the determination of the spring stiffness.

Jan 1, 2015

By Charles A. Schacht

"Relining, lining maintenance, and ladle repair can represent a significant cost in steelmaking. Therefore, the objective of all steelmaking shops is to minimize this cost and to maximize the lining life. However, the thermomechanical behaviour of the ladle lining is highly complicated and sometimes misunderstood. The ladle design also has a significant influence on lining life. Other factors which have a direct influence on lining life are the shop lining installation practices and manner in which the ladle is used. The objective of this paper is to provide an understanding of the impact of these factors as related to improving the integrity of the lining and increasing lining life.Fundamentals of Steelmaking Ladle Lining Expansion ForcesNumerous studies have been conducted by the author on steelmaking ladles with molten metal capacities ranging from 110 ton s to 350 tons. The steelmaking ladle typically has a sidewall plate with a slight taper and for analytical purposes can be classified as a cylindrical vessel.A typical ladle is described in Figure I. The ladle sidewall lining usually consists of a working lining and a safety lining. Although the type of refractory used in the working lining varies based on the type of steel produced and other metallurgical requirements, the refractories typically used are: 70% alumina brick; direct bond mag-chrome brick; resin bond dolomite brick; and direct bond dolomite brick. Fireclay brick, high alumina brick, or a similar strength brick is used as the safety lining.Normally, the ladle lining is exposed to a through-thickness temperature gradient and restrained by the ladle sidewall plate, is described in Figure 2. The hot face side of the refractory lining develops a compressive thermal force and the ladle sidewall plate develops an equilibrating tensile force. The radial joints open on the cold side of the working lining as the lining joints have little or no tensile strength. A radial compressive load (P) develops between the working lining and the vessel shell due to the thermal restraint imposed on the lining by the shell. The radial compressive load is transferred from the working lining through the safety lining onto the ladle sidewall. Therefore, the safety lining must have the strength to accommodate the radial compressive load (P)."

Jan 1, 1991

By G. K. Lee, Whaley. H., F. D. Friedrich, I. C. G. Ogle

"IntroductionCurrent coal combustion activities at the Canadian Combustion Research Laboratory (CCRL) reflect the increasingly important contribution that coal is expected to make in meeting our future energy requirements and in reducing our dependence on foreign oil. Widespread use of coal will, however, be heavily dependent on the ability of conventional and emerging combustion systems to cope with the disruptive conflicts caused by variations in fuel quality, on requirements for better equipment availability .and on the implementation of progressively more stringent environmental constraints.To minimize these conflicts, Energy, Mines and Resources Canada has embarked on a systematic sequence of research, development and demonstration- scale (R, D and D) initiatives to stimulate the utilization and competitiveness of thermal coal in both domestic and export markets through a number of complementary in-house projects and external contracts, considered to have short- to intermediate-term benefits to industry and society.Many of the in-house projects are funded in part by industry, whereas the external contracts are either fully funded (100070 government funding) or jointly funded (50% government - 50% project proposer).External contracts and shared-cost projects are an important adjunct to the CCRL in-house effort on coal combustion, because research data can be more effectively transferred to industry and because the commercialization of novel combustion systems can be accelerated significantly."

Jan 1, 1980

By J. W. M. Porritt, M. P. Brameld, R. H. McCorkell

"Soil-gas Rn was measured by two types of alpha-particle-track detectors, by emanometry and by counting alpha-activity on Rn-decay-product collectors. Soil samples were analyzed for V by fluorimetric and fission-track methods, their Rn-emanation by decay-product collectors and their total alpha activities with track detectors. The same uranium anomalies were revealed by each method. Fission-track analysis of leaves for V showed only random variations with sampling site, and the Rn emanation of trees and leaves removed from them was barely detectable . The agreement among the other methods is significant, total alpha and collector methods are simple, rapid and useful, and a combination of methods at a site would reveal disequilibrium in the U-decay series if present. Track-Rn measurements are highly reproducible and insensitive to apparatus design and their sensitivity is not enhanced by covering the detectors with thin foil or placing them in large containers.IntroductionIn the past two years , a number of methods of geochemical exploration for uranium have been tested by the authors over the known copper-uranium occurrence at South March, Ontario. This was done partly to compare methods and partly to develop and test new ones. The South march deposit has been described a number of times by others(1,2,3,4). The methods included in this study were the following.Emanometry, Radon in soil gas is measured by pumping the gas into the cell of a scintillation counter or emanometer(5,6). Alpha particles from radon (222Rn) and its decay products (218Po and 214Po) produce scintillations of light in the silver-activated zinc sunphide (ZnS(Ag) covering the walls of the cell. These are counted by a photomultiplier tube and scaler, the count ra sulphide (ZnS(Ag) covering the walls of the cell. These are counted by a photomultiplier tube and scaler, the count rate being proportional to the concentration of radon in the soil gas."

Jan 1, 1981

By Denghong Wang

Abstract- The Ashele Cu-Zn deposit is a recently discovered volcanogenic massive sulfide deposit in Xinjiang, China, hosted by Lower to Middle Devonian submarine bimodal volcanic rocks. The primary ores of this polygenetic deposit are represented by massive syn-depositional pyrite, chalcopyrite, and sphalerite, and were formed by submarine exhalation. Hydrothermal alteration consists of strong sericitization, chloritization, silicification, and carbonatization of the metavolcanic rocks beneath the massive orebodies. Depletion of Na2O is an obvious chemical change in the hydrothermal halo. Geological and geochemical evidence suggest that the Ashele Cu-Zn massive sulfide deposit was formed by submarine exhalation related to bimodal volcanic rocks, trapped in a rifting basin, then deformed by shearing, and thermally metamorphosed by the intrusion of dacitic porphyry. Sulfur and lead isotopic studies indicate that metals such as copper and zinc may have originated from spilites, but that volatile components, especially sulfur, were derived directly from submarine volcanic magmas.

Jan 1, 1999

By P. S. Daly

"The purpose of this paper is to describe the types of instrumentation used at Sherritt Gordon's Ruttan Mine to monitor the"" effects of mining. The aim of the monitoring program is to establish parameters to achieve a maximum ore recovery with minimum dilut ion in a safe environment.The copper-zinc Ruttan Mine is in northwestern Manitoba, approximately 760 km from Winnipeg (Fig . I) . Production commenced in 1973 from the open pit at the rate of 10,000 tons per day. Pit bottom lies 58 metres above the first mine level. Underground development has overlapped with open-pit mining throughout. The open pit was phased out in the latter part of 1980.Underground production began in early 1979. The mining method employed in the first lift is sub-level blasthole open stoping with delayed hydraulic filling. Large-diameter (6.5-in.) holes are being drilled in the crop stope area and are also planned for some other areas for vertical retreat mining into a slot. GeologyThe orebody consists of numerous sulphide lenses of variable size, geometry and geology . The lenses occur within volcanoclastic host rocks which exhibit a strong variability in intensity and type of alteration and structural characteristics. Stope design and sequencing were based on these complex geological factors."

Jan 1, 1981

By John A. Meech

"Oleic acid flotation of Mount Wright thickener underflow tailing material has been shown to be capable of increasing plant recovery by 3%. High levels of oleic acid addition (1.5 kg/t) are required, which limit the economic practicality of the system at this time. Nevertheless, from a technical viewpoint, the process is stable with respect to extreme fluctuations in oleic acid requirements, pulp pH and pulp temperature. Methods to reduce the average consumption of oleic acid need to be found. One technique that merits further testwork uses the ""piggy-back"" principle to float hematite fines with coarsegrained hematite particles.IntroductionWith most large-scale iron mining operations treating specular hematite ores, flotation is not often conside red a necessary processing step. The bulk of the iron minerals can be concentrated by gravity techniques and the generation of fines can be minimized because of the course- grained nature of the mineralization. Nevertheless, production of some fine material is unavoidable, and recovery of iron from this fraction by spirals is poor (10-30%).When the proportion of the iron in these fines becomes excessive, alternative methods to conventional spirals are considered(11), Many of the techniques that have been developed suffer from either poor recovery (e.g. the Reichert cones at 36010 recovery)(11) or low throughput rates (e.g. wet highintensity magnetic separation)(12), Flotation is often passed over because of excessive reagent costs, pollution problems and/or balling difficulties from the reagents used.However, of all the processes available, flotation can yield high recoveries (60-90%) at reasonable throughput rates with excellent process control features (reagent addition and/or cell level). The key parameter is reagent cost.This paper describes testwork on the use of oleic acid to float hematite from the fine fractions of the Mount Wright concentrator tailing. The concentrate product from this plant is directly shipped, so no balling problems exist. As well, oleic acid may be considered a lesser pollution hazard than many of the cationic collectors used in other iron ore flotation systems. A reduction in fine hematite slimes discharged as tailing into lakes may also reduce environmental damage."

Jan 1, 1981

By E. G. Parker

"Sherritt's zinc pressure leaching process converts zinc sulphide concentrates directly to zinc sulphate solutions and elemental sulphur. Thus, one pressure process step replaces both the roasting and leaching operations of the conventional roast-leach route. In addition, high single-pass extractions eliminate the need for residue treatments to recover unleached zinc. Because pressure leaching produces elemental sulphur, rather than sulphur dioxide, acid plants and smoke stacks are not required, and air pollution control and work-place hygiene are greatly improved. .In 1977, Cominco Ltd. and Sherritt Gordon Mines Limited jointly operated a three-tonne-per-day pilot plant to demonstrate pressure oxidative leaching of Sullivan zinc concentrate and the subsequent separation of elemental sulphur. The process consisted of regrinding the concentrate, continuous leaching at 150°C at elevated oxygen pressures in a four compartment autoclave and the subsequent recovery of elemental sulphur, either in the molten liquid form from a decantation autoclave or as a flotation concentrate. Of the zinc contained in the concentrate, 97% was extracted in 90 minutes, and 96% of the sulphur was converted to the elemental form.Following the successful pilot campaign, Cominco began building the world's first commercial zinc pressure leaching plant. This plant, which was in operation by late 1980, will eventually treat about 25% of Cominco's planned zinc capacity of270,000 tonnes per year.This paper describes the general process principles, the results obtained from the pilot plant and the integration of the process into Cominco's operations at Trail. The application of pressure leaching to a ""grass-roots"" plant is also discussed, and compared with conventional roast-leaching."

Jan 1, 1981

By E. Contestabile, T. R. Craig

"This report describes the development and effective use of shaped charges as part of the Elliot Lake Mine Roof Stability Project to remotely remove the heads from roof bolts. With a slight modification, these same shaped charges are being recommended f or use to the Brunswick Mining and Smelting Corporation Limited (Mining Division), to cut steel cable bolts.IntroductionThe Canadian Explosives Research Laboratory (CERL) often receives requests to cooperate in solving problems encountered in private industry or other sectors of the government. CERL is equipped to design and test explosive and pyrotechnic devices and the policy is to treat each case individually.The first case reported evolved from a request from a sister laboratory at Elliot Lake. The intent was to remotely remove the head s of roof bolts as part of a mine roof stability project. The device designed for this use was 1000,70 effective in the laboratory and 80% effective in the mine.The second case reported results from a request from a private mining company knowledgeable of the Elliot Lake Project. Their requirement was to remotely cut cable bolts. This request was first treated as presenting a new problem. The solution, however, proved to be very similar to the former."

Jan 1, 1985

By Errol Ladner

The application of large-diameter bore holes in underground operations at Heath Steele was first tried in February, 1975. Since that time, 90,000 feet of 6-l/2-inch holes have been drilled, primarily in open blasthole stoping, for a total of 1.4 million tons, 37% of underground production. This paper deals with a review of drilling with conventional percussion longhole drills, a practice which is still utilized at Heath Steele, and the changeover to accommodate the use of larger blastholes in underground operations. The discussion will include layouts for 2-inch-diameter blasthole stope blocks, 6-inch-diameter stope blocks, trials for I. T.H. (in-the-hole) stope rooms, and drill pat/ems, drilling and performance. The complexity involved in the development, drilling and blasting of 2-inch blastholes is overcome by the over-all simplicity of drilling and blasting in I. T.H. stopes. This has made the practice of open blasthole stoping more economical and efficient. The future indicates an increase in the company's I. T.H. program. Investigations are being undertaken regarding longer holes to decrease development costs. A VCR stope is also being developed for trial.

Jan 1, 1979

"The gravimetric dust sampler is one of the tools now available to the industrial hygienists for determining the worker 's exposure to the numerous types of particulate matter that may be present in the workplace. The paper ' reviews the different sampling trains that can be used for the two major criteria for respirable dust and some of the sources of error in this dust assessment technique.IntroductionIt may be stated simply that the measurement of airborne dust in the working environment is done for one or two reasons: namely, for engineering control purposes and! or to evaluate the potential for toxicological insult arising from the inhalation of dust particles.This paper reviews the progress made in the development of dust-assessing instruments, particularly the gravimetric types designed to meet British and U.S. dust criteria , and discusses the limitations in their use for this purpose."

Jan 1, 1981

By A. L. Mular

"IntroductionSince the mid -1960s, automatic control of grinding circuits has become the rule, to avoid losses attributable to frequent circuit upsets associated with uncontrolled disturbances such as ore hardness variations. Higher capital costs of grinding equipment and corresponding operating costs-especially with respect to energy consumption-are major factors that continue to stimulate interest in grinding control.Grinding circuit control strategies depend upon the control objectives defined by the processing plant and are subject to constraints such as: maintain final per cent solids within some range, do not transport steel ball s out of the discharge trunnion, or do not overflow or empty the pump box and so on. Constraints depend on the nature of equipment employed within the grinding circuit and may actually determine the characteristics of the control scheme. Typical control objectives are:1. Maintain final particle size at set point by ,a. manipulation of fresh feed rate with circulating load maintained by manipulation of pump box water addition rate, orb. manipulation of pump box water addition rate with circulating load maintained by manipulation of fresh feed rate, where the methodology utilized to accomplish either (a) or (b) is dependent upon equipment/circuit constraints such as the availability of a variable speed pump.2. Maintain circuit throughput at a maximum by,a. manipulation of fresh feed rate subject to constraints on final particle size and variables such as power draw, circulating load and mill overload.3. Maintain mill load at set point by a. manipulation of fresh feed rate subject to constraints such as on power draw.4. Maintain mill power draw at set point bya . manipulation of fresh feed rate subject to mill load constraints. Often, a grinding control objective is dictated by the recovery vs fineness-of-grind characteristic that exists for downstream separation circuits. When recovery is relatively insensitive to size, maximum throughput in the grinding circuit is advantageous.The purpose of this paper is to review control strategies for primary ball mill grinding circuits, rod mill/ball mill grinding circuits and semi-autogenous grinding mill circuits. Primary sensors employed are highlighted and modern trends are documented briefly."

Jan 1, 1989

By S. Dallaire

With the attainment of high temperatures it becomes possible to process any kind of material (particularly ceramics) in their liquid state. In the plasma spraying process, the material to be sprayed is rapidly heated until it is molten and is propelled by high velocity gases onto a surface where it adheres, to give protective coatings for a wide range of applications. The method could be considered as one of the most versatile and rapid to build up thick deposits (of plastics, metals, ceramics, cermets) and also free-standing artifacts for particular requirements without resorting to lengthy forming and sintering studies. Although plasma spraying is at the production stage in industry, advanced processes have also been developed for economically producing a wide range of new materials. This paper illustrates the benefits of the process and evaluates the challenges it represents.

Jan 1, 1987

By G. R. Baiden

"An Automatic Haulage Truck (AHT) has been developed for manless tramming of run-of-mine material in an operating mine. The AHT has a 70-ton capacity and uses an electric trolley system in combination with a computer control system to operate the vehicle. The purpose of the AHT was to provide a high capacity, high productivity material transfer system where conveyor belt applications are not immediately practical.The AHT project was started in 1983 at Inco Limited, Ontario Division as a result of the need for rapid material transport to match increased extraction rates resulting from bulk mining methods. The original concept was to use a continuous loader with the truck. However, in order to minimize development problems the truck project was considered a stand-alone project.The AHT project consisted of concept development, preliminaryand detailed design, manufacture, surf ace testing and mine implementation.The AHT was manufactured and ready for testing in 1988. At this point the truck was first moved onto the test track for debugging. This proved successful and in 1989the decision was made to install the AHT at Little Stobie mine on 2000 level. Commissioning of the system was started in 1990and at present a fully functional automated haulage system is in place at Little Stobie mine producing 3000 tons/day.This paper describes the project presenting results achieved to date."

Jan 1, 1992