Search Documents

By Gennaro Delisle

"Les Services TMG (Niobec) currently treat a niobium ore in the Chicoutimi area of Quebec. The mineral pyrochlore is present in a carbonatite deposit which assays 5% to 7% apatite.The ore is ground to minus 65 mesh and deslimed at 10 micrometres. Part of the carbonates are floated with a fatty acid emulsion and rejected to the tailings as a first step to ensure the proper conditions for the flotation of the pyrochlore concentrate. The carbonate concentrate is 65% minus 44 micrometres and is composed of dolomite, calcite, 22% apatite and a minor amount of silicates.A laboratory investigation was undertaken to determine the feasibility of extracting apatite from the carbonate concentrate. This led to the development of an economic flowsheet to produce high-grade apatite concentrate. The apatite is depressed with phosphoric acid, and the pH is adjusted at 4.8-5.0 with sulphuric acid. An additional amount of fatty acid is added to permit efficient flotation of the carbonates. 1n a second stage, the silicates left behind with the apatite concentrate can be removed by depressing the apatite with AIC3 while floating the silicates with a secondary amine.The results of the laboratory tests indicate the possibility of producing an apatite concentrate assaying 38.3% P2O5 (83.7% BPL) with a recovery of 66.2%. Pilot-plant tests undertaken at the concentrator yielded a concentrate of 34% P205 and recovery of 76%."

Jan 1, 1981

By W. G. McBride

INTRODUCTION Preparation of this article, at the request of the Committee on papers, has been undertaken in the hope that it may stir up helpful discussion and constructive criticism. The Canadian mining industry is in the dumps and there is no use trying to deny the fact; nor does it help to say that other industries are in as bad or a worse condition. Let us face the situation honestly and see just how serious it is. The entire financial and industrial world is in a state of depression. The gravity of the case is no doubt exaggerated by contrast with the wave of optimism and false prosperity which pre-ceded it. The prevailing gloom and pessimism are just as irrational as was the former super-optimism. As far as we mining engineers are concerned, the causes are quite beyond our control, and it is the effect upon our own industry which interests us most. This effect is an accumulation of mineral products with consequent depression in price to a point where profits have almost, if not quite, disappeared. Whether this accumulation of stocks is the result of over-production or under-consumption is difficult to say, but it would seem likely that there is a combination of the two. The introduction of selective flotation has brought about a large increase in the production of zinc, a moderate increase in the production of lead, and a comparatively small increase in copper. It has turned relatively small mines into great producers, as in the case of the Sullivan, revived expiring mines like La Cananea, and brought-in new ones like Flin Flon

Jan 1, 1931

By R. Roufail

Mineral liberation is accomplished by comminution and is the first step towards achieving successful downstream processes such as flotation or leaching. In metal mining, one of the most effective comminution methods that is used to grind particles below 10 microns is stirred milling. In this paper the study of particle breakage mode vs. mill operating parameters is addressed. Stirred mills' grinding action is mainly attrition, but operation can be manipulated to include breakage by compression or impact loading. Macro and micro analysis of particle breakage and grinding mechanisms are correlated. Macro analyses convey information that relates grinding mechanism to particle size and shape. It is speculated that the breakage mechanism in the horizontal stirred mills is massive fracture for the coarsest particles and attrition (abrasion) close to the grinding limit where the size reduction ratio approaches 1.0. For micro analysis, the particle breakage mode has a direct impact on fracture type either transgranular or intergranular. Intergranular particle breakage leads to higher mineral liberation compared to transgranular breakage. Similar minerals would have more homogeneous properties that convey a stronger bond compared to dissimilar, heterogeneous mineral bonds. Transgranular fracture requires higher energy than inter granular fracture; trans granular fracture toughness of pure single phase mineral is about 10-14 % higher than the intergranular fracture toughness. This communication presents the results of an investigation to assess how operating conditions can affect trans- vs. inter-granular breakage.

Jan 1, 2009

By G. R. Yourt

"Generally speaking the usual approach for controlling dust is three-fold:1. Suppress the formation of dust at the source.2. Confine dust that cannot be suppressed.3. Dilute and remove dust that cannot be confined.This discussion will be concentrated on the second approach, namely, confining and disposing of dusty air.Dust BehaviourBefore delving into actual design principles a brief discussion on behaviour of dust should be helpful. For prevention of silicosis only respirable dust, ranging in size from < 0.5 to 5u needs to be controlled. As particles of this size have insignificant mass and momentum they follow air movements very closely. Consequently if contaminated air around dust sources is confined within enclosures and leakages maintained, strongly indraft dust is automatically controlled and capture velocities are of no concern.Dust SourcesAt metal mining operations ore is prepared for wet concentration by crushing it to mostly <3"" in size. This usually involves a jaw crusher, one or two cone crushers, one or more screens and several conveyors. Dust is actually produced only by the crushing action but it is liberated also when numerous fine particles contained in the ore stream are dispersed by surges and vibration at the discharge of the crushers, screens and headpulleys of conveyors. Furthermore, dust is dis¬persed when the slime adhering to the underside of the return portion of belts becomes dry and is rendered airborne by vibration and by cleaning floors especially where the slime has dropped."

Jan 1, 1971

By H. E. Frimmel

Most of the gold in the Late Archean Witwatersrand Basin is of detrital origin but, in its present form, it is metamorphosed. The only relict detrital features preserved are the morphological characteristics of some placer gold particles. Regional burial metamorphism in the shallower and deeper levels of the Witwatersrand Supergroup reached temperatures around 300°C and 350°C at pressures between 2 kbar and 3 kbar, respectively, estimated from phase relations, chlorite-chloritoid exchange thermometry and chlorite thermometry. Metamorphism of the gold involved compositional homogenization of individual gold particles and partial recrystallization. Various infJ.1tration events caused the partial mobilization of the gold at slightly lower temperatures, between 240°C and 300°C. These infiltrations can be related to crustal extension during the deposition of massive carbonate sequences of the Transvaal Supergroup (around 2.5 Ga), and later to the emplacement of the Bushveld Complex, and to the Vredefort event around 2.0 Ga ago. The mobility of the gold was dependent on the sulfur fugacity prevailing in a particular horizon which, in tum, was determined by the amount of pyrite (and other sulfides) present in that horizon. With the sulfur fugacity being controlled by stratigraphy, low fluid rock ratios in a pyrite-rich horizon were most conducive for the mobilization of the gold. Thus, long-range gold mobilization in the Witwatersrand Basin can be expected to be the exception rather than the rule.

Jan 1, 1994

By E. J. Marcotte

"IntroductionDevelopments in the preparation, hydraulic transportation and placement of classified mill tailing as an effective backfill and support for mining excavations, have made feasible several advancements in mining methods that are safer and more economical. Hydraulic backfill systems have played an integral part in the development of more efficient cut-and-fill and blasthole stoping.The hydraulic transportation of tailing fill has made possible the elimination of expensive and laborious transportation, placement and spreading of gravel type fills. Also, in cut-andfill stopes, the use of hydraulically placed consolidated fill has largely eliminated the need to use extensive timbering for floors and supports, previously necessary when only gravel type, waste rock or unconsolidated tailing fill was used .Another important advantage of using mill tailing as backfill is that it decreases the need to contain a large portion of the mill solids waste in a surface disposal area and thus reduces environmental and ecological problems.Tailing Fill PropertiesConsolidated tailing fill consists of deslimed mill tailing and Portland cement. These two materials are mixed together in various proportions to form a high density slurry which is transferred underground by gravity through boreholes and pipelines. After placement underground, the water is drained off and the mixture is allowed to set. The strength of the consolidated fill is dependent on the cement content, particle size distribution and curing time. A typical tailing/ cement ratio used for bulk filling in stopes requiring vertical wall support is 30:1. Ratios ranging from 8:1 to 5: 1 are used for stope floors. High pulp densities minimize segregation and loss of cement during placement as well as reduce the amount of drainage water to be handled."

Jan 1, 1989

By L. J. Friedman

The recovery of sulfur dioxide from metallurgical gases for the production of sulfuric acid has been the primary means of reducing sulfur dioxide emissions from nonferrous smelters. Sulfuric acid has been produced from gas originating from fluid bed roasters, electric furnaces, reverberatory furnaces, flash smelting furnaces, Pierce Smith and flash converters, sinter machines, etc. The gas from each of these sources has a unique set of variables that affect the design and operation of the sulfuric acid plant. In addition, the sulfuric acid plant itself has been evolving, with new equipment designs and materials. This paper will review each of the unit operations in the gas cleaning and contact sections of the metallurgical sulfuric acid plant, discussing various equipment designs, materials and the handling of gas stream variables and impurities. The paper updates to 2007 previous works on metallurgical sulfuric acid plants by the authors, and analyzes new equipment and systems, including: FRP or alloy quench systems, alloy converters, towers and pump tanks, heat recovery systems, high efficiency mist eliminators, tower packing, etc.

Jan 1, 2007

By Pamela Paradis-Sokoloski, Deni Thibodeau, J. Denis, Samantha J. Espley, P. O’Donnell

"During the previous decade, the role of spray-on liners within the mining industry was limited to providing a corrosion resistant coating to screen and bolts; however, increasingly, liners are being used as ground support products. Expanding use and testing of liners have demonstrated their ground support function, yet the definitive support mechanism is still under debate. The most promising theory is the retain/hold/reinforcement concept (Kaiser et al.,1992). This conceptual theory has been the basis for the recent underground trials at INCO where, specifically, shotcrete and MIROC Mineguard were tested in two trials to further define limitations and applications of each liner.In a cursory overview, shotcrete is becoming accepted as a support product, while Mineguard is only slowly gaining acceptance.This discrepancy is the result of the corresponding life-spans within the industry, whereby shotcrete has had wide-spread use for decades, yet Mineguard has only recently been introduced. Currently at INCO, shotcrete is primarily used: to provide support in poor ground conditions, to add stability when developing through backfill, and to provide damage control in seismically active mines. It is also used to protect production headings and secondary-blasting chambers from fly-rock damage during blasting. Despite an obvious support function of the liner, shotcrete has always been used in addition to bolts and screen. Comparatively, Mineguard is still in the testing stage, where the greatest potential is increased productivity for applications in multi-tasking development headings. In this scenario, Mineguard provides instant support to replace screen, and bolts temporarily. When the heading has advanced, the drill and support crews work in tandem, drilling off the next round and installing bolts for long-term radial support, respectively. Other potential applications of Mineguard are within production headings to replace screen in the back, and screen and bolts in walls. The potential for both liners to replace conventional support is clearly war-ranted, such that defining the support role was the primary goal of the two underground trials."

Jan 1, 1996

By John L. Rich

A New Field for the Mining Industry A new field for the mining industry is in prospect. This is the recovery of the petroleum which has been left in the ground in the older oil fields whose yield has declined until they are no longer profitable to operate in the ordinary way. The fact that an oil field has reached the economic limit for operation by pumping does not necessarily &apos;mean that the oil has ? been exhausted. In many such cases not over one-fifth, or even one-tenth, of the total oil content of the field may have been taken out when this stage has been reached. This means that there exists a large reserve of oil which can be recovered by whatever process best takes advantage of the natural conditions under which the oil occurs. Mine drainage is one of the processes by which this oil may be recovered. Its relative importance will depend partly on the ingenuity and wide-awakeness of mining engineers, and on mining capital. The opportunity is undoubtedly at hand. In order that we may be in a position to judge the possible advantages of mining methods for the recovery of this oil, I have reviewed, on the following pages, the methods now in use, and have discussed the physical conditions of the reservoir rocks in which the oil is found, and the suitability of the various recovery processes, in use or proposed, in the light of these reservoir conditions.

Jan 1, 1927

By A. A. Sirkeci, M. Tarkan, N. Acarkan, O. Kangal, G. Bulut

This investigation deals with the evaluation of the tailings of the Kirka Borax Plants. In this respect boron in the tailings was recovered and the utilization of the clayish fraction was investigated. There are five tailings ponds in Kirka four of which are used for the tailings of the borax concentrator and the remaining one is used for the tailings of the sodium penta-borax plant. Experiments were conducted with samples taken from ponds containing coarse fraction and fine fraction. Coarse fraction of Borax Concentrator were screened through a set of sieves. The fraction above 1 mm was removed with 41.5% recovery and 33.3% B203 content. Scrubbing was applied above 0.1 mm and products containing 32 to 34% B203 were obtained with recoveries around 35%. The tailings of sodium penta borax plant was also screened and it was found that 15% of boron reported to +1 mm size fraction with 35% B203 content. Sample containing fine tailings was treated by cycloning. The cyclone overflow was found to be below 6µm and it was separated to be used in the subsequent tests. The usage of cyclone overflow in paper, ceramics, glass, pigment and drilling industries was investigated. Since this fraction is mainly composed of carbonate minerals rather than clay minerals it was suggested that it may be used for construction and moulding purposes. Furthermore, the B203 content of the cyclone overflow was reduced to 2.4%.

Jan 1, 2004

By C. J. R. Braithwaite, Giancarlo Rizzi

"The Navan zinc-lead ore deposit (70 million tonnes) is hosted principally (97%) by the Meath Formation (Lower Carboniferous, Courceyan, Navan Group), comprising a lower, mainly carbonate mudstone unit, the Stackallan Member, and an upper grainstone-dominated unit. TheStackallan Member, about 60 m thick, comprises about 35 peritidal cycles including an oolitic grain-stone interval. Grainstones forming the upper part of the formation, about 150 m thick, comprise at least six shallowing-upward ramp cycles. Emergence horizons are indicated by subaerial dissolution surfaces, in situ breccias, and a single palaeosol.Most dolomitization at Navan is con?ned to the Meath Formation. The linear dolomite body,trending NE-SW, has a ?attened, laterally limited, tabular geometry in cross-section, suggesting that dolomitizing ?uids initially rose vertically, cross-cutting stratigraphic and sedimentological bound-aries, although ?uid ?ow was subsequently controlled by these features.Three stages of dolomitization are indicated by textural relationships, cathodoluminescence (CL),oxygen isotopes, and ?uid inclusion data. Stage 1 crystals, with generally dully luminescing cores and up to six overlying subsidiary zones, are the main replacive phase. Crystal surfaces are commonly corroded and overlain by bright stage 2 rhombs (which also form new nuclei lining molds and fractures). Three subsets of zones are present in stage 2 crystals: bright, non-luminescent, and dull; these are locally separated by additional corrosion surfaces. Stage 3 comprises relatively large baroque crystals, generally dully luminescent but with up to seven sub-zones. Isotopic and ?uid inclusion data suggest growth of successive stages from waters which became progressively hotter(60°–160°C).The distribution of the ores follows the dolomite trend. Ores were precipitated between Stages1 and 2 of dolomite growth, following Stage 2, and also during the nucleation and growth of Stage3 crystals. Dolomitization and mineralization appear to have been temporally and genetically related. The cyclic sedimentation of the host rocks, which accentuates lithological and petrographical contrasts between depositional units, controlled dolomitization. The relationship between dolomitization and mineralization, which is closely associated with faults, provides powerful exploration criteria. The recognition of these features in limestones elsewhere in the Irish ore ?eld may point toward unrecognized zinc-lead prospects."

Jan 1, 1997

By C. J. R. Braithwaite, Giancarlo Rizzi

"Abstract-The Navan zinc-lead ore deposit (70 million tonnes) is hosted principally (97%) by the Meath Formation (Lower Carboniferous, Courceyan, Navan Group), comprising a lower, mainly carbonate mudstone unit, the Stackallan Member, and an upper grainstone-dominated unit. The Stackallan Member, about 60 m thick, comprises about 35 peritidal cycles including an oolitic grainstone interval. Grainstones forming the upper part of the formation, about 150 m thick, comprise at least six shallowing-upward ramp cycles. Emergence horizons are indicated by subaerial dissolution surfaces, in situ breccias, and a single palaeosol.Most dolomitization at Navan is confined to the Meath Formation. The linear dolomite body, trending NE-SW, has a flattened, laterally limited, tabular geometry in cross-section, suggesting that dolomitizing fluids initially rose vertically, cross-cutting stratigraphic and sedimentological boundaries, although fluid flow was subsequently controlled by these features. Three stages of dolomitization are indicated by textural relationships, cathodoluminescence (CL), oxygen isotopes, and fluid inclusion data. Stage 1 crystals, with generally dully luminescing cores and up to six overlying subsidiary zones, are the main replacive phase. Crystal surfaces are commonly corroded and overlain by bright stage 2 rhombs (which also form new nuclei lining molds and fractures). Three subsets of zones are present in stage 2 crystals: bright, non-luminescent, and dull; these are locally separated by additional corrosion surfaces. Stage 3 comprises relatively large baroque crystals, generally dully luminescent but with up to seven sub-zones. Isotopic and fluid inclusion data suggest growth of successive stages from waters which became progressively hotter (60°-160°C).The distribution of the ores follows the dolomite trend. Ores were precipitated between Stages 1 and 2 of dolomite growth, following Stage 2, and also during the nucleation and growth of Stage 3 crystals. Dolomitization and mineralization appear to have been temporally and genetically related. The cyclic sedimentation of the host rocks, which accentuates lithological and petrographical contrasts between depositional units, controlled dolomitization. The relationship between dolomitization and mineralization, which is closely associated with faults, provides powerful exploration criteria. The recognition of these features in limestones elsewhere in the Irish ore field may point toward unrecognized zinc-lead prospects."

Jan 1, 1997

By T. Möller

Grinding mills are the heart of the mineral processing plant, and are production-critical machines which are required to achieve high availability. Liner wear life and a liner design that promotes ease of installation are important variables to achieve a high level of mill availability. Increased mill size results in more mill internal surface to protect, and more liner components to install and remove. This drives designers toward an increase in liner size to minimize the number of components to be installed by the liner handler. The liner attachment method can also have a large impact on mill availability as well as safety during installation. This paper outlines the experience from the development, installation and follow-up of liners installed in two 38&apos; x 45&apos; AG Mills at Boliden Aitik in Sweden. A new Poly-Met shell liner concept has been developed to minimize the number of liner components. The new Poly-Met shell liner components are made much larger than conventional Poly-Met or steel liners. This reduces the number of components to be installed/removed by the liner handler and helps to minimize installation time and consequently down- time. A new attachment system has also been developed to eliminate the need for the installation crew to be in the ?drop-zone? of the shell liners while installing the liner bolts. One interesting aspect of this project was the requirement to predict liner life for these new large format AG mills. The existing 22&apos; diameter mills at Aitik provided a base-line reference for this purpose, and DEM studies were used in the project development stage to predict the wear life of shell liners for the new 38&apos; diameter AG mills. The results from this study are included.

Jan 1, 2012

CAT offers three different methods to accomplish crowd & retract on an electric rope shovel Rack and pinion Rope crowd HydraCrowd The presentation will compare the three systems and introduce the benefits of the Hydracrowd

May 1, 2013

By Unkown

The Province-wide road ban on movement of heavy loads has had the effect of curtailing or stopping development in several areas. In the Leduc area, the discovery well has been restricted in flow to only a fraction of normal due to limited storage space, but drilling at Imperial Leduc Nos. 2, 3, and 4 has been continued for the past few weeks. The No. 2 well is within 100 feet of the producing horizon and should be completed within the next few days. According to reports, it has been logging slightly lower, structurally, than the discovery well, but, regardless of the outcome, it has been an important test to determine westerly cross-section of the Leduc structure. No official reports have been made available of any tests made during the drilling of the well, but it is understood that promising oil and gas shows have been indicated in higher formations. Actual drilling operations have not been commenced by any of the other companies holding leases in the immediate area but it is expected that, when road bans are removed and equipment is assured, several wells will be commenced. Announcement has been made that Imperial Oil, Limited, will drill a well near Battle lake, about thirty-five miles southwest of the Leduc field. Location of the well has been made following an extensive seismograph survey of the area, with total depth of the test well expected to be in the 8,000- to 8,500-foot range. Drilling will be done with the heavy-duty rig last used at the De Winton test. Imperial Oil have abandoned hope of oil production in the Provost area after drilling nine wells, but will retain their interest in the gas field that has been developed. Of the wells drilled, four indicated gas flows ranging from 1,060 to 13,200 M.c.f. per day.

Jan 1, 1947

By Oscar F. Tangel

This paper outlines Canada&apos;s current status in world iron ore markets, and evaluates t he prospects for the future. Estimates for the production, export and consumption of iron ore are given. Canada&apos;s major market will continue to be the United States, with the European Common Market countries, Japan and the United Kingdom also forming important outlets. The advantages held by Canada&apos;s major competitors in these latter three market areas are briefly discussed

Feb 1, 1966

By Oscar F. Tangel

This paper outlines Canada's current status in world iron ore markets, and evaluates the prospects for the future. Estimates for the production, export and consumption of iron ore are given. Canada's major market will continue to be the United States, with the European Common Market countries, Japan and the United Kingdom also forming important outlets. The advantages held by Canada's major competitors in these latter three market areas are briefly discussed.

Jan 1, 1966

By S. A. Willis

For over 150 years gypsum from Nova Scotia has been shipped via water to the United States east coast. The history of the movement has been one of continual improvements in quarrying, loading, and shipping. At the start, man-size rock quarried by hand auger and black powder was loaded into horse-drawn carts, hauled to the waterfront, and dumped into 100-ton sailing schooners. Last year the Canadian Gypsum Company completed the latest and most modern of these successive installations for the movement of this Nova Scotia product. The new system loads crushed gypsum into 11,600-ton vessels at Hantsport in two hours&apos; time at high tide. At the head of the bay of Fundy are located vast deposits of gypsum. The tidal rise and fall of 45 feet twice a day, with its attendant swift currents, has always presented major navigation and shipping problems. When the tide is low, the Hantsport ship-loading pier is high and dry, with no water within 400 feet. Three hours later a large river has flooded in (running up hill) and large steamers can dock at the wharf. Before high water, the ship has been loaded and -there is a depth of 30 feet or more of water around the wharf. At high water, the ship sails away on the ebbing tide as the river runs in the other direction. Tides are caused by the gravitational attraction of the moon and sun on the ocean. When both celestial bodies are pulling together the &apos;spring tide&apos; results, which means a 50-foot variation from high to low. This occurs at new and full moon. A week later, when the sun and moon work in opposition, the difference is only 32 feet between high and low water. The bay of Fundy, having a funnel shape (150 miles wide at mouth from Yarmouth to Portland, while the upper estuary at Hantsport is only one mile wide), builds up a tidal influence from 10 feet at the mouth to an average of 45 feet at Hantsport.

Jan 1, 1948

By Eugene Sun, Qiang Xu

This presentation will review current applications of composite materials in aircraft design and discuss the challenges involved in maximizing the potential of the composites in aircraft applications.

Jan 1, 2010

By A. Sadough vanini A. Kami

In this paper, effects of different ageing treatments on the mechanical properties, microstructure and formability of 7075 aluminum alloy have been studied. Forming limit diagrams of the alloy have been obtained for four ageing conditions including T6, OA1, OA2 and O. For this purpose, combination of uniaxial tensile tests and the Erichsen cupping tests with different sizes and shapes of sheet specimens have been performed after each ageing treatment. The highest formability and the lowest formability have been observed at samples with O and T6 ageing treatments, respectively. Also, investigation of precipitated microstructures showed that the size of precipitation particles has a significant effect on the formability of the alloy. Formability improves with coarsening of precipitation particles.

Oct 1, 2011