Search Documents

By S. Litke

Elemental sulfur was stockpiled at the Mount Polley Mine for use as a source of sulfuric acid as part of research into leaching copper from oxide ores, but the project did not proceed beyond an initial pilot- scale evaluation. Since placement, the sulfur has oxidized and some sulfuric acid leached into the underlying rock. The reaction of the acid with these underlying materials has been studied as part of an evaluation of the effects of leachate from the pile. The rock underneath the sulfur pile is composed dominantly of primary and secondary alumino-silicates with less than 1% carbonate (calcite) and iron sulfide (pyrite). In its unaltered condition, the rock is classified as non-acid generating. Conceptually, it was expected the sulfuric acid would be neutralized by the rock to varying degrees resulting in a series of pH-controlled weathering fronts progressing from leached near the contact with the sulfur pile (pH <3), to active neutralization by silicates (pH 4–5), to active neutralization by carbonates (pH >7). The rocks underneath the pile were sampled to determine the extent to which the rocks had reacted and their long-term stability after removal of the acid source. INTRODUCTION When rock is blasted and excavated to facilitate mining ore, it is typically placed and stored on the surface in piles. The resulting drainage may have a neutral to basic pH (i.e., non-acidic drainage) or a low pH (i.e., acid rock drainage, ARD) depending on the mineralogy of the rock being stored in the piles. Acid- base accounting (ABA) can be used to characterise the two types of rock: potentially acidic drainage generating (PAG) and not potentially acidic drainage generating (NAG) (Price, 2009). According to Price (2009), NAG is defined as having an excess of neutralization potential (NP) in the rock in the form of calcium carbonate-like minerals when compared to acid potential (AP), i.e., a Neutralization Potential Ratio (NP/AP = NPR) greater than 2.0, whereas PAG is classified as having an excess of AP (i.e., an NPR less than 1.0). This is a conservative estimate and may be slightly modified depending on the mineralogy at specific mine sites. Rock with an NPR of 1–2 is also capable of generating acid (Price, 2009) and, depending on the mineralogy, may also be classified as PAG. Drainage from PAG material can generate acid immediately, or many years after it has been exposed to surface conditions. Disposal techniques depend on the category (i.e., NAG or PAG) and reactivity of the rock stored in the piles.

Jan 1, 2019

By G. Morin, G. Marin, M. C. Parr, J. Carignan

"Investment casting offers many advantages for the near net shape production of complex geometries, however, molten titanium reacts with most of the refractories used in investment casting shelling systems, which leads to the formation of an oxygen contaminated surface layer. This layer, called alpha case, is 0.1 to 0.6 millimeters in thickness according to the casting section size and must be removed either by mechanical or chemical milling processes. Alpha case removal processes affect casting tolerances and may contaminate the part intended for medical applications (e.g. embedding of abrasive grit media in the alloy). A shelling system based on an yttria prime slurry has been developed and was found to almost suppress the mold metal reaction. Yttria is an expensive refractory, but slurry life was found acceptable for small castings using a closed container and flow coating process instead of conventional pattern dipping. Alpha case depth has been determined for Ti6Al4V by metallographic techniques and microhardness measurements on different step block casting cross sections. Alumina and yttria second prime stuccos were evaluated in this study. The shelling system minimizes finishing operations in the production of casting for medical applications.INTRODUCTIONTitanium investment castings have been in the commercial market since the beginning of the titanium era in the mid 50’s. Investment casting is a cost effective way to produce complex parts for medical, aerospace and chemical processes applications. Investment casting of titanium is difficult due to the high reactivity of titanium with air and refractories used for shell mold building especially for the face coat. Melting is done under vacuum and no shelling system has been proven effective to suppress the mold-metal reaction yet. The main issue with the mold-metal reaction is the formation of an oxygen enriched zone at the surface of the castings named alpha case (Frueh et al., 1997; Kim, 2002; Saha, 1986). The alpha case is brittle, reduce the fatigue life in service of the parts and must be removed by chemical milling.For industrial purposes, calcia partially stabilized zirconia based slurries have become widely used in titanium investment casting for primary coats due to a combination of limited metal shell reaction. Calcia stabilized zirconia slurries have an acceptable shelf life and offer an interesting production window. Our experience shows that a resulting alpha case depth is 280 micrometers for a casting section of 6.35 mm in thickness is typical with such a shelling system (Morin, 2013)."

Jan 1, 2016

By P. C. Holloway, M. J. Collins, K. R. Buban

Historically, there has been little incentive to process copper-arsenic concentrates by leaching, rather than via established smelting operations. However, with ever tightening environmental emission standards and more arseniferous concentrates being produced, increasingly sophisticated and upgraded off- gas handling facilities are required in smelting operations, generating greater quantities of challenging metallurgical dust. In this context, oxidative pressure leaching offers distinct advantages. The current state of pressure leach technology delivers high extractions from copper concentrates, while producing an environmentally stable process residue, without atmospheric emissions of sulphur dioxide or arsenic. However, as was shown in an earlier study, copper extractions and environmental leach residue stability are impacted negatively by arsenic levels above 2.5 to 3.0 wt%. In further studies on pressure leaching of copper concentrates, Sherritt has developed process conditions that allow even highly arseniferous (> 7 wt% As) feed materials to be converted into environmentally stable residues, with excellent copper extractions. At the same time, pressure leach residues can be generated that are amenable to silver recovery via direct cyanidation, without pre-treatment by lime boiling or hot curing. The results of pilot plant test work are discussed. INTRODUCTION As the production of copper has expanded over the years, resource exploitation has extended beyond relatively clean, high grade and easily accessible ores, and copper sulphide concentrates increasingly come with higher levels of contaminants, such as As, Hg, Sb and Bi, and lower copper and sulphide sulphur concentrations. However, as concerns on the impact of the emission of such contaminants into the natural environment have mounted, import/export restrictions have made the trading of copper concentrate more difficult, and, in particular, the export of concentrates with greater than 0.5 wt% As; under ever tightening environmental emission standards, these lower quality concentrates can be a significant strain on the off-gas handling facilities in smelting operations. The processing of arsenic bearing copper concentrates is, therefore, an increasing challenge as copper producers seek to exploit more complex mineralization and to extend the life of their operations. In this environment, processing arsenical copper concentrates with high temperature pressure leaching (>200°C) must be considered as an alternative to pyrometallurgical processing. Leaching kinetics for copper minerals at these temperatures are rapid and acid is generated for potential use in heap leach operations. Pressure leaching of copper concentrates eliminates gaseous emissions of arsenic and sulphur, while generating environmentally stable residues, as measured by the Toxicity Characteristic Leach Procedure (TCLP) (Kalanchey et al., 2007). Both medium and high temperature pressure leaching of copper concentrates have also proven themselves technically on an industrial scale (Marsden et al., 2004) with high copper recoveries.

Jan 1, 2019

By Dan Zou, Ji Chen, Deqian Li

"Bayan Obo mixed RE concentrate is the largest RE source in the world. RE elements occur dominantly in bastnaesite and monazite. This paper describes a clean and green technique for processing Bayan Obo mixed rare earth (RE) concentrate. A two-step oxidation method can lead to the effective recovery of REs, thorium (Th), fluorine (F) and phosphorus (P). Ce has a property of valency change, enabling the separation of it from other RE(III) elements. Making use of the interactions of cerium (IV) (Ce(IV)), F and P, a new extraction system was created to separate Ce(IV) effectively from other RE(III) while recovering F, P and Th by complexing F and P following the oxidation of Ce(III) to Ce(IV). The method includes two parts. Firstly, bastnaesite is oxidized by air roasting and sulfuric acid leaching. And then a first leach liquor containing Ce(IV), F and P is obtained. Secondly, monazite was converted into REhydroxide through alkaline attack and then Ce(III) in the RE-hydroxide was oxidized into Ce(IV) by wetair oxidation. After sulfuric acid leaching the oxidized RE-hydroxide, a second leach liquor is obtained. The two parts of leach liquor containing Ce(IV), F and P are then extracted by Cyanex923 to obtain CeO2, CeF3 and CePO4 based on the complex of Ce(IV) with F and P. The raffinate was further extracted by the primary amine N1923, and Th-product was recovered as ThO2. The RE elements recovery yield during the whole process is greater than 92%. The new technique not only provides a new way for Bayan Obo RE ore utilization, but also avoids resource waste and environment pollution.INTRODUCTIONRare Earths (REs) refer to lanthanides, including scandium and yttrium. Owing to the similar structure and property of RE(III), it is difficult to separate them from each other, especially for the adjacent elements. According to the United States Geological Survey, in 2010, the whole world has about 142 million tonnes of rare earth reserves. In that, China ranks the second with 22% following Brazil which ranks first with 32% (Cheng, 2011). There are three main RE ore types in China with about 80% mixed ores in Bayan Obo, 10% bastnaesite ores in SiChuan and ShanDong province and 2.9% ion adsorption ores in Southern China. Bayan Obo mixed RE concentrate consists of bastnaesite and monazite. The concentrate contains CeO2/_REO of 50% and there are 7–8% F, 4-6% P and 0.2–0.3% Th."

Jan 1, 2016

By Joey R. Kish, Shooka Mahboubi, Hatem S. Zurob, Gianluigi A. Botton

The kinetics of the Cr2O3-based scale oxidation and volatilization were studied in the presence of water vapour (H2O). A commercial Cr2O3-based scale forming Type 310S stainless steel was examined at the ambient pressure (0.1 MPa) and 550ºC in relatively low and high H2O containing environments of air- 10% H2O and air- 70% H2O, respectively. The increase in the partial pressure of H2O (pH2O) from 10% to 70% resulted in transition of the oxidation and volatilization kinetics from the parabolic rate law for air-10% H2O to the paralinear rate law for air-70% H2O. The kinetics transition was attributed to the increase in the Cr loss rate from the base scale after coupons exposure in air- 70% H2O. The significant role of the Mn alloying element in the base scale protectiveness was also discussed in the context of the Cr2O3-based scale stability.

Jan 1, 2017

By R. R. Irrinki

Abstract -The Key Anacon deposit consists of four sulfide zones called, from south to north : Key Anacon No. 1, Key Anacon No. 2, Key Anacon No. 3, and Key Anacon Copper Zone. Massive sulfides of zones 1, 2, and 3 are underlain by rocks correlated with the Nepisiguit Falls Formation and are overlain by matie volcanic rocks correlative with the Boucher Brook Formation. In contrast to zones 1, 2, and 3, narrow northwesterly-trend.ing, copper-rich fracture zones occur within the Patrick Brook Formation. Sulfides in zone 2 occur as three mineralogical associations, namely: pyrite-chalcopyrite, pyrite-sphalerite-galerta, and pyrrhotite-sphalerite-galerta. The distribution of lithologies and en-echelon patterns of the three sulfide lenses of Key Anacon No. 2 zone are the result of F1 and F2 folding. Zone 2 is the most promising economically, with proven reserves of 1.11 million tonnes grading 0.2207o Cu, 3.47% Pb, 8.41% Zn, and 96 g/t Ag; the zone is open below a depth of 427 m.

Jan 1, 1992

By P. G. West-Sells

At Barrick&apos;s Zaldivar Copper Mine in Chile, the addition of sulfuric acid to the ore going to heap leaching is a major expense. A process in which a portion of this acid is replaced by elemental sulfur added to the heap has been developed by Barrick and Westcoast Biotech that has the potential for significant cost savings. Initial shake flask tests with plant raffinate solution indicated that oxidation of elemental sulfur by a culture of sulfur-oxidizing bacteria, some indigenous to the Zaldivar heap, showed a significant lag period. This lag period could be reduced by dilution of the raffinate, but dilution would not be economical to implement at Zaldivar. Short (0.75 m) column tests indicated that after the initial lag period, sulfur biooxidation occurred steadily and the acid requirement for obtaining the same copper recovery as the control without sulfur was reduced by as much as 13 kg/t. These tests were followed by taller (5.1 m) column tests that confirmed the reduction in acid consumption, with no negative effect on copper extraction.

Jan 1, 2007

By N. Sarmady, Mei Li, N. C. Parson, W. J. Poole

"The mechanical behaviour of AA6082 is a function of the extrusion conditions and in particular, the quench rate after extrusion. It is well known that precipitation of Mg-Si phases on grain boundaries during quenching can negatively affect the ductility of the alloy. In this study, AA6082 alloys containing 0.5 wt. % Mn and 0.15 wt. % Cr were direct chill (DC) cast, homogenized and then extruded to produce 3 mm x 42 mm strips. The microstructure in the as-extruded strips was unrecrystallized due to the Zener-Smith drag from the Mn/Cr dispersoids. It was shown that a solution treatment of 5 minutes at 560°C did not significantly affecting the as-extruded microstructure but if the as-extruded strip was cold rolled prior to heating, recrystallization occurred concurrently with the solution treatment. As such, 3 initial microstructures were produced, i.e. unrecrystallized and recrystallized with a grain size of 9 and 40 µm. After the solution treatment, controlled cooling experiments were conducted using the Gleeble 3500 thermomechanical simulator with cooling rates of 10, 25, 80°C/s as well as water quenched. The mechanical properties (e.g. yield stress, fracture stress and fracture strain) were determined from tensile tests for the different combinations of initial microstructure and cooling rate. The relationship between the quench rate and precipitation of Mg-Si phases on grain boundaries was examined by FEG-SEM. It was found that the yield stress decreased as the cooling rate decreased and that there was complex relationship between the fracture properties and the microstructure.INTRODUCTION As the automotive industry strives to reduce fuel consumption and CO2 emissions with the goal of reducing the environmental impact, there is a need for lighter vehicles. As a result, aluminum alloys are gaining popularity to replace steel parts as structural components. An exemplar of this is the Ford F-150 pickup truck which has an aluminum body and is ˜750 pounds lighter than the previous steel version of the vehicle. The structure includes a mix of aluminum sheet, extrusions and cast alloys. The current research is concerned with the performance of aluminum extrusions in applications such as side rails, crash tubes and other structural parts. These components experience a combination of bending, stretching and folding both during the forming of the part and in service, e.g. crash of a vehicle. There is a need to have detailed information on the influence of processing on final material performance, in particular the cooling rate after extrusion."

Jan 1, 2018

By W. Petruk

"D. Doyle How large is the beam to which you referred? Are we considering Watts, Griffis the probe of a 1 micron sized particle?& McOuatReply Yes. The beam would be about 1 micron. We could enlarge or reduce it depending on the current in-put.D. Doyle Then chemically bound material we might not see. If you are restricted to 1 micron then you would not be able to separate things smaller than this. Is this not so?Reply We won't be able to analyse it but we will see it as the scanning electron microscope has a resolution down to about 0.1 microns. We should be able to get the general composition of such a grain plus its surrounding grains. We feel we can then make a reasonable estimate if it were as small as 0.1 microns. An accurate analysis would be achieved with grains of 3 and 4 microns.D. Doyle Would this have an application in the hydrocarbon field?Reply The lowest atomic number would be sodium. We wouldn't be able to go below that atomic number. Anything with sodiumor a larger atomic number would enable us to analyse the carbon.M. Fairwether Do you have any policy relating to priorities. For instance areCominco companies going to be limited in the amout of samples permitted to give everyone a chance because quite frankly our company, and I'm sure all base metals companies can hardly wait for the installation of this equipment. I can forsee two years back-log of work in the first month.Reply Quite frankly, I haven't looked at this. At the present time the work is under the START program but I suppose we will have to look at possible changes. Anything under the START program has first line priority.B. Thorndycraft Will the briquetting of samples be automated as well? Pinson MiningReply No, not at this point. Our polish section laboratory is first-class and can turn out 18 polish sections a day which is more thar we can handle.B. Thorndycraft With the capability of this machine to operate in a hands-off manner perhaps it could start to look for the 5 micron gold particle in tailings?Reply I have such a program using a wave-length spectrometer rather than the energy dispersive. The wave-length spectometer is about 10 times as sensitive and would scan the section much faster. A one inch diameter polished section would be scanned in about 7 hours for anything 1 micron or larger."

Jan 1, 1984

By David C. Mulder

As a result of the dramatic growth of Edmonton, Alberta during the past decade and the rapidly increasing price of natural gas, Edmonton Power has received provincial government approval to construct and operate an 8O0-megawatt- capacity coal-fired thermal generating station at Genesee, about 50 km southwest of Edmonton. The power plant will consist of two 400-megawatt steam-driven thermal generators, with provision in the future for two or more additional units. The coal will be hauled by truck from the nearby three-million-tonnes- per-year strip mine, with economically recoverable reserves exceeding two hundred million tonnes. Edmonton Power controls a major part of the coal leases in the area, and is working with other lease holders in developing the most efficient mining plan. A natural depression was selected as the site for the 600-hectare cooling pond to provide water for the power plant. Edmonton Power is working closely with the people in the area to ensure that their rights and concerns are communicated and recognized by all parties.

Jan 1, 1981

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Froth depth or interface level is an important control variable in column flotation which can influence both grade and recovery. A common method of locating the level is based on sensing the hydrostatic pressure at one or more points along the column. The level indicated can be in considerable error, largely because of variations in froth and collection zone bulk densities. A portable conductivity probe has been developed to detect the position of the interface from conductance measurements across the interface. The location of the interface corresponds to the position where a large change in conductance is observed, which is primarily a consequence of the difference in gas holdup between the collection and froth zone. This probe detects the position of the interface to an accuracy of ± 5 cm. The probe can be used while the column is in operation, which allows for on-line recalibration of the level detection system. Results obtained in its application in a pilot-scale column (0.91 m in diameter) are described.

Jan 1, 1990

By P. R. A. Andrews

"Areas of bubble contact were delineated for cassiterite in the presence of chloride, fluoride, sulphate, phosphate, oxalate and citrate ions using dodecylamine hydrochloride collector. The limits of pH, and the minimum collector concentration were established using the bubble pick-up technique.Bubble contact did not occur below the p.z.c. (point of zero charge), estimated to be 4.7, in the presence of chloride ion, and fluoride ion showed only a weak response in the same pH range. These anions are considered to act as indifferent electrolytes. Activation at pH values below the p.z.c. was obtained with sulphate, phosphate, oxalate and citrate ions; the greatest response was by oxalate and phosphate ions extending pick-up to between pH 2.0 and 2.5.Activation appeared to be strongest when anionic protonated species were in maximum concentration. Strong activation also corresponded to the formation of very stable metal ion species, thought to be formed on the surface of cassiterite, between exposed stannic ions and modifying anions; dodecylammonium ions being absorbed on the surface so modified."

Jan 1, 1991

By Juan C. Sotomayor Álvarez

The Huantajalla mine is seated on Uchucchacua &apos;s Mixing District that is the fourth producer of Silver in the world. Huantajalla Mine is a new mine that nowadays is being explored and recently it has began to operate. The project for 4-A vein exploitation in Huantajalla Mine using Longhole drillings as a new method of mixing is developed by Planning Department of Uchucchacua Mine in coordination with Geology Department of this mine, started in June 2004. This project is funded by Company of Mines Buenaventura S.A.A In July 2002, Geology Department started the exploration on the area of Huantajalla Mine, discovering the 4-A vein. The reconnaissance and definition of the vein finished June 2003, finding 79,080 Ton of mineral of Silver with a grade of 40.0 Oz Ag/ton and a thickness of 1.85 meters (6 feet ). Using the longhole method on the vein exploitation will replace the cut and fill and shrinkage methods, and it will keep a dilution of 15%.

Oct 1, 2004

By Wouter Bleeker, Isabelle Cadieux

"Abstracts of theses related to mineral deposit studies and exploration, completed at geology or earth science departments of Canadian universities, have been compiled for the period 1991 to mid-l993. Part I, presented in the June 1994 issue of the CIM Bulletin, gave a listing of thesis titles. Part II, which consists of edited abstracts of these considered to be of direct application to mineral deposit studies and exploration, is presented under various themes as follows;A. Kimberlites, Other Alkaline Intrusions and Related Studies;B. Volcanogenic Massive Sulphide Deposits and Related Studies;C. Mineral Economics;D. Mesothennal Gold Deposits, Other Gold Deposits and Related Studies;E. Magmatic Nickel-Copper, Platinum Group Element, and Chromite Deposits and Miscellaneous Platinum Group-related Studies;F. Granite and Pegmatite-related Deposits and Porphyry Deposits;0G. Diverse Hydrothermal Deposits, Sediment-hosted Copper Deposits and Mississippi Valley Type Lead-Zinc Deposits; andH. Uranium-related studies, Evaporites and Exploration GeophysicsAbstracts related to themes A. B and C are presented in this issue; the remaining abstracts will be presented in future issues."

Jan 1, 1994

By H. Somekawa

The fracture toughness and deformation structures an AZ31 magnesium alloy processed by equal-channel-angular extrusion (ECAE) were investigated. The average grain sizes of as-ECAE and annealed-ECAE alloys were 4.0 and 16.3 µm, respectively. The plane-strain fracture toughness, Kip, in as-ECAE and annealed-ECAE were estimated to be 27.3 and 23.5 MPam1/2, respectively, by stretched zone analysis. The fracture toughness indicated higher value with grain refinement. From optical microstructural observations in samples after fracture toughness tests, although deformation twins were observed in annealed-ECAE, no deformation twins were observed in as-ECAE. From TEM observations, the dislocations on basal and non-basal planes were activated in as-ECAE. With grain refinement, the activations of dislocations on both basal and non-basal planes were possibly related to the reduction in formation of deformation twins in as-ECAE. In addition, in comparison with direct extruded process, ECAE process was more effective method to improve the fracture toughness in magnesium alloys.

Jan 1, 2006

By Sandra L. Mesa-Espitia, Gretchen T. Lapidus

Gold present in arsenopyrite matrices is refractory and requires highly oxidative pretreatments in order to obtain acceptable degrees of extraction. However, these release many byproducts that are harmful to the environment. In the present work, a high-grade arsenopyritic ore was pretreated with different solutions, containing hydroxide ion, EDTA, oxalic, tartaric, or citric acids, to improve gold extractions in a posterior leaching step. The pretreatments were carried out at room temperature for 24 hours with a respective ligand concentration of 0.25 M. Once completed, the residue was leached in a thiosulfate solution to quantify the effect of the pretreatment on gold extraction. Only 29% of the gold content was leached, with very slow kinetics, in the untreated mineral. However, after pretreatment with tartaric or citric acid, the kinetics improved, although the percentage of gold extraction only reached 42-45%. The highest gold recovery, with very rapid kinetics, was found with the oxalic acid or the hydroxyl ion pretreatment (70 and 62%), respectively, but also corresponded to the most arsenic co-dissolution.

Jan 1, 2014

By E. Faria

"The Santa Rita mine is located in north eastern part of Bahia in Brazil and is owned and operated by Mirabela Mineração do Brasil Ltda. Typical SABC circuit was designed as the preferred option for the 4.0 mtpa (500tph) to produce a P80 of 125um for flotation. Although the SAG was originally designed to operate with conventional radial pulp lifters, later it was fitted with Outotec’s Turbo Pulp Lifters – TPL (Latchireddi, 2005). The milling circuit commenced commissioning on the 24th of October 2009 and the milling circuit achieved the nameplate capacity within days. with small and relatively simple measures to rectify. Since commissioning, the SAG mill has been working in fully autogenous grinding (FAG) mode with no balls (in contrast to the estimated 10% ball charge) and has been consistently treated up to 650tph.This paper examines the comminution design process, the operating philosophies, start-up experiences, post commissioning optimization and future development works. An evaluation of mill performance relative to the design criteria for the project life to date is also included."

Jan 1, 2012

By K. D. A. Whaley

The Captain North Extension deposit consists of five sulfide lenses hosted in cherty and chloritic metasediment that is bounded by quartz-eye rhyolite and laminated rhyolite. Lens 2 consists of sphalerite and galena with silver-rich tetrahedrite in chert. Lens 3 contains massive pyrite, with chalcopyrite and minor gold, gradational to minor pyrite in a chloritic metasediment. The other lenses are unexplored. The sulfides occur as beds, fracture infills, and disseminated grains. Reserves are estimated at 207 555 tonnes grading 7.380/0 Zn, 2.76% Pb, and 91.81 g/t Ag. The deposit is isoclinally folded, dips steeply west, plunges 50 degrees south, and is faulted out to the north, where drag folding has reversed the plunge. Minor cross-faults contain talc and sericite. High sphalerite but low pyrite abundances result in poor responses to standard electromagnetic techniques. Lens 3, which contains more pyrite than Lens 2, responds better to induced polarization and allows detection. Geochemical anomalies are found in a nearby swamp and stream, but an impervious till cover inhibits the development of soil anomalies.

Jan 1, 1992

By J. E. Gill

THE 1938 season was marked by a distinct lull in exploratory activity in the Province of Quebec. Quebec was not unique in this respect, but the condition appears to have been more acute here than in most other parts of the Dominion. Various causes may be suggested to account for this. The general disturbance in political and economic conditions throughout the world has certainly had an adverse influence. Uncertainty induced by changes in the mining laws of Quebec in 1937 contributed. A third cause was the belief, now held by many, that the easily accessible deposits in the main producing belt extending eastward from. the Rouyn district have now all been found and that new discoveries in this field will henceforth come more slowly and more expensively. A fourth is the lack of conspicuous success by companies and individuals who have interested themselves in less accessible areas to the north, notably the Chibougamau district. A fifth, the unattractive appearance, as viewed on published geological maps, of the vast area extending northward to Ungava bay and Hudson strait. A sixth, the attraction of such speculative funds as were available to the Northwest Territories, where spectacular finds were reported in the fall of 1937. Whatever may be the relative importance of these causes, languor in exploration will ultimately be reflected in production returns. This appears, therefore, to be an opportune time to take stock of the general position of the Industry in the Province and to consider ways and means of counter-acting those conditions which are now impeding, or will in the near future impede, its expansion. At the request of the Institute Secretary, Mr. Carlyle, I have prepared a brief summary of accomplishments to date and a discussion of some of the geological aspects of the problem.

Jan 1, 1939

By N. W. D. Davis

"As I have recently carried out some further research on the Navan lead-zinc deposit data while working in Michel David's research team, I should like to add a few comments on the paper- ""Universal Kriging for Ore-Reserve Estimation- Conceptual Background and Application to the Navan Deposit"", by M. Dagbert and M. David (CIM Bulletin, pp. 80-92, February 1976). The first comment is that since this research has been carried out, important new theoretical advances have been made which make for an easier application of geostatistics to the non-stationary case (see Matheron0l). This is the theory of intrinsic random functions of order k. With the aid of this theory, it has been possible to write computer programs which can carry out automatically universal kriging, although so far such applications have been largely confined to automatic contouring and not to mining problems. However, if approached with care there is no reason why these methods should not be applied to mining problems and, in this case, an automatic study has been done on this data."

Jan 1, 1976