Search Documents

By A. Scheltema Beduin, H. Oterdoom, A. Haaks, C. Kempe, A. Liedtke

"For the Kazchrome DC Ferrochrome plant, SMS-group specifically designed an electrode column that would minimize downtime. Special features include the possibility for on load electrode jointing, on load slipping, and back-slipping. Electrode consumption is strongly related to furnace load and impedance, and is very low at high loads, which makes the graphite electrode an alternative to consider even in AC applications. The electrode could also be applied in other DC applications, as for example TiO2 slag, the novel Conroast process, or (twin) DC FeNi furnaces, and could possibly be installed during bigger shut downs. This paper will describe some of the design considerations and operational performance data on this novel column in the FeCr industry that could also be of interest for the FeNi or PGM industry if these would continue to develop towards DC technology.INTRODUCTION Every DC furnace has a cathode and an anode. The anode applied is commonly known as the Concast design, though the original design was by ABB who handed it over to Concast, subsidiary of the SMS-group. Some well-known DC furnaces outside the steel industry where the Concast bottom has been installed are listed in Table 1 as well as a few other key design features.Sidewall cooling and some other data have been left out for reasons of space, and being a lesser relevant design feature to this paper. HES stands for Hollow Electrode System, in which feed is charged through an electrode. Table 1 is built up chronologically according to first start-up date. Below comments are given to briefly explain some of the columns in Table 1: •,“Arm” in the “Cathode” column means that the design of the cathode holding and regulating mechanism consists of an electrode arm as depicted in Figure 1. •,Charging is relevant as some operations started with HES charging, whereas recently most new operations have started without HES but only charging chutes, of which at least some are close to the electrode and possibly others installed closer to the sidewall. •,“Dome” in the “Roof” column means that the design of the roof involves a center piece that can be exchanged if worn. •,The optimal roof design still seems to be a topic of debate, where no design is without problems."

Jan 1, 2017

By A. Blackmore, D. Baker, L. Human

"Mechanical mixing equipment is common in a wide variety of mining, metals and process applications, such as hydrometallurgical reactors, solvent extraction, digestors, and tanks for storage of slurry or hydrocarbons. Computational Fluid Dynamics (CFD) has been applied successfully to single-phase mechanical mixing problems for several decades and is established as a reliable design tool. As computational power and CFD codes have improved over the years, there have been significant advances in modelling capabilities including improved models of turbulence, interaction of rotating and stationary components, multiphase flows, and modelling of free surface interfaces, for example. This paper will provide an overview of the application of CFD to mechanical mixing problems. First, it will review the traditional single phase Multiple Reference Frame (MRF) approach and introduce a range of advanced modelling techniques. Three examples of the application of CFD to industrial mixing problems will be given. It will be demonstrated that CFD is an effective tool for reducing technical risk in design, for identifying the root-cause of mixing problems, and testing modifications to existing operations."

Jan 1, 2015

By J-F. Béland, N. Parson

Aluminum extrusions are widely used for automotive crash management systems due to their superior specific energy absorption capabilities, as compared to steel. The Al-Mg-Si alloy series can be readily extruded into complex multi-hollow profiles, as required in crash systems, and can be used to target a range of desired strength levels. This paper focuses on the development of an axial crush test protocol and evaluation of the crush performance of common 6XXX series alloys for a variety of tempers. The observed crush behaviour is then compared to tensile test results.

Jan 1, 2015

By V. G. Papangelakis, G. A. Moldoveanu

The use of anhydrite (AH) seed, control of acidity levels and ageing were assessed as means to promote the conversion of freshly produced metastable gypsum generated in-situ to the less soluble anhydrite phase and force deposition of calcium sulphate on seed as opposed to on equipment as scale, while achieving lower terminal aqueous calcium concentration as well. It was found that moderate sulphuric acid levels (0.25M) and ageing in the presence of AH seed accelerated the gypsum-AH conversion, achieving 100% transformation of the metastable gypsum generated in situ to the more stable, less soluble AH in 6-7 days, while lower/nil acidity did not promote more than 30% AH conversion for 10 days, even in the presence of AH seed. These findings indicate that anhydrite seeding, ageing and incomplete neutralization are beneficial for scale control as well as achieving lower calcium levels, thus rendering the resulting solution more amenable for recycling.

Jan 1, 2015

By R. Esteban, D. Runnels, J. Torrealba-Vargas, G. Couture

"Data handling is an important step in the development of a simulator of a mineral processing circuit. The model requires representative data of the scenario to be modeled. The model development involves protocols that must be followed very closely to complete a successful project.Data handling of large and diverse datasets (metallurgical test results, geological data, mining models, historical data, etc.) is a key element of the model. The information needs to be processed, reconciled, interpreted, modeled and presented to support the design or the optimization of a mineral processing plant.Best practice recommends that teams from different disciplines (such as mining, metallurgy, geology and environmental) interact to define the most important variables that could influence the simulator. For example by adopting a geometallurgical approach in the earlier stages of the project, it is possible to consolidate the number of main ore rock types in a testwork program (saving money and time) by involving geologists and metallurgists in the sample selection and data interpretation.Planning the development of a model involves an understanding of the software capabilities but also the limitations and the magnitude of the data required to calibrate the model in case of changes in the project.A successful model requires a deep understanding of the circuit to be modeled and thus plant personnel should be considered as members of the team.This paper describes the use of the "state of the art" tools for data analysis, simulation and optimization; and shows three practical examples of the use those tools in the design of mineral processing plants."

Jan 1, 2015

By Ozdemir. O.

Magnesium additions to aluminum enhance strength and hardness, lowering density, and improving corrosion resistance. However, during melting and casting processes, significant amounts of magnesium are lost due to selective oxidation. Preventing these losses would reduce the production cost and improve the quality of the final product. The effects of strontium addition on the oxidation behaviour of aluminum-0.5% and 1% magnesium alloys were investigated by monitoring sample weight gains with time with a thermogravimetric balance at 750°C. Sample cross sections have been examined using Field Emission Gun Scanning Electron Microscope.

Jan 1, 2004

By C. Hari Manoj Simha, J. Gholipour, M. J. Worswick

Due to the high pressures involved in the hydroforming process, friction and lubrication play an important role and can affect formability of the material. Tubes of A1Mg3.5Mn aluminum alloy, of 76.2 mm (3 inch) outside diameter and 2-mm thickness were considered in this study. Three kinds of lubricants, Al070, Hydrodraw711 and water, were applied to the tubes and tubes were hydroformed to burst in a square shape die cavity. The key process parameters were recorded during the tests. An in-house Gurson-Tvergaard-Needleman (GTN) damage-based material model, implemented in LS-DYNA, was used to model the process and predict the formability of this material. The applied axial loads and internal pressures recorded during the tests were used in the computations. The effect of different types of elements (solid and shell) with different constitutive models (von Mises and GTN models) in predicting the strain distribution is studied. The GTN damage-based material showed a good ability to capture necking and displacement histories in this process. Both predicted and measured results showed that the lubricant with lower coefficient of friction can effectively increase the comer expansion.

Jan 1, 2006

By N. Manopulo, J. Maier, L. Tong, C. Becker, P. Hora

The contribution presents a new finite element approach in which the common updated Lagrangian formulation is replaced by a spatial flow formulation applying a special arbitrary Lagrangian-Eulerian for-mulation (ALE). The description separates spatially the process in a die inside zone and in a profile zone. For the description of the inside zone, where the filling process occurs, a special Euler time independent mesh is applied. By this formulation the mesh has to be generated only once, which simplifies the generation of spatially optimized meshes. For mapping of the material flow during the filling process the method uses a flow surface traction method as applied in casting simulations. A further strength of the new method is the computational efficiency which allows the modelling of extrusion process with the highest complexity with a response time of 12 hours, which is important for the industrial optimization process.

Jan 1, 2015

By J. -M. Lalancette, D. Lemieux, C. Chouinard

"A gold bearing concentrate containing 107 g/T of gold, 9.3% copper and 706 ppm of mercury was processed at the demonstration scale for the extraction of gold and copper using a cyanide free process. The concentrate was generated through flotation to upgrade the gold and copper grade, but also showed contamination with mercury. This concentrate was submitted to the DST process demonstration plant. The concentrate was first oxidized using a fluidized bed to produce a calcine. The mercury was volatilized during the oxidation stage with an efficiency higher than 98%. The mercury was condensed and removed from the sulfuric acid using a thiosulphate process. Copper was extracted from the calcine as copper sulphate using diluted sulfuric acid. The solid remaining after acid leaching was submitted to the DST chlorination process for gold extraction. Under optimized conditions, a gold extraction of 97.3% was achieved in the chlorination reactor. Gold was recovered from the pregnant brine by precipitation on silica using a DST proprietary process.INTRODUCTION Dundee Sustainable Technologies Inc. (DST) offers proprietary metallurgical processes for the treatment of material from the mining industry. DST processes enable the extraction of precious metals and for the removal and stabilization of contaminants, such as arsenic, from ores and concentrates. DST provides environmentally-friendly, viable and efficient processes, capable of handling complex and refractory ores which cannot be processed with conventional approaches due to metallurgical issues or environmental considerations. Several mining jurisdictions around the world have banned or restricted the use of cyanide. DST has developed a closed loop chlorination process as an alternative to the conventional cyanidation process for the extraction of precious metals from minerals. The tailings from the process are inert from toxic substances such as cyanide and organic compounds, are sulphide depleted which means they do not generate acid, and thus, meet and/or exceed environmental norms. The process has demonstrated excellent gold recoveries within a fraction of the time needed for cyanidation to obtain similar results. Moreover, the closed loop process does not generate any liquid effluent and does not consume much water: it only requires a water make-up to compensate for moisture leaving with the tailings and by-products, and seawater may be used. The improved environmental footprint of the DST process has been certified by the Environment Technology Validation program (ETV) which provides an independent evaluation of the performance claims of innovative technologies."

Jan 1, 2017

By F. Mohamm

"Recent changes in regulations and scientific advances concerning selenium bioaccumulation have placed greater importance on non-biological treatment systems for selenium control. Mining wastewater contains hexavalent selenium (selenate) as the predominant aqueous species and possibly small amounts of tetravalent selenium (selenite). Non-biological removal of selenite is accomplished readily and cost effectively by ferric co-precipitation and adsorption using ferric oxyhydroxides sourced from ferric salts or iron anodes in electrocoagulation cells. Selenate on the other hand is difficult to remove. It is often incorrectly assumed that electrocoagulation is suitable for removing both selenite and selenate. Selenate removal efficiency by electrocoagulation is low and the amount of waste residue produced high. In contrast, BioteQ’s Selen-IX™ process removes selenate very efficiently and produces a much smaller amount of stable residue. The process combines selective ion exchange with electro-reduction of selenate in electrocells that physically resemble electrocoagulation cells but are designed and operated differently. This paper summarizes four years of pilot scale demonstration on a wide range of mine waters and discusses the key benefits and limitations of Selen-IX™. The pros and cons of combining ion exchange with electro-reduction in comparison to direct electro-reduction of selenate are also reviewed.INTRODUCTION Selenium in Mining and Mineral Processing Effluents Similar to sulphate and metals, selenium presence in mining and mineral processing wastewater originates from minerals contained in the mined deposits. Therefore, no organoselenium species are typically present in these kinds of waters and inorganic species including selenite (SeO32-), selenate (SeO42) and elemental selenium account for the majority, if not all, selenium present in these streams. Elemental selenium is not always present in mine water but is often contained in smelter wastewater. To comply with new environmental regulations, a successful water treatment plant must remove selenium from all these forms effectively and economically without generating by-products that are difficult to dispose of or manage. Elemental selenium can be dealt with using filtration or gravity separation in clarifiers often assisted by flocculants and/or coagulants. Mine impacted waters typically contain other forms of suspended solids which are removed from water in this way. Once the solids are removed, the selenium species that remain untreated are the dissolved forms. In mining waters this is mostly selenate with small fraction of selenite. In smelter wastewater, the majority could be selenite. It is well established that tetravalent selenium is readily removed from water by using ferric iron co-precipitation at pH > 4 (NAMC SWG, 2010). Ferric hydroxide/ferrihydrite solids act as the adsorbent for tetravalent selenium when it is in one of the ionic forms of biselenite or selenite. This treatment for tetravalent selenium is highly efficient. Therefore, tetravalent selenium removal is generally not an issue and is often easily incorporated into lime neutralization or unit operations such as electrocoagulation used for removing other metals present in mine impacted waters. Another option of dealing with tetravalent selenium is sulphide precipitation in acidic pH which produces SeS2 and can separate selenite from other metals and/or sludge produced at neutral to alkali pH."

Jan 1, 2017

By R. L. Bruening, R. M. Izatt, N. E. Izatt, S. R. Izatt

"Molecular Recognition Technology (MRT) is a simplified, green chemistry process with applications in selective separations of Ni(II), Co(II), and platinum group metals in primary ore beneficiation processes and secondary recovery operations from spent products, scrap, and environmental waste solutions. Simplification in MRT processes is achieved by non-use of solvents, reduced space requirements, and a simple separation system involving columns packed with metal-selective SuperLig® resins. Minimal waste is generated and metal recovery is achieved at 99% levels from g L-1 to <mg L-1 concentrations. MRT systems are attractive technologically and economically compared with solvent extraction, ion exchange, and precipitation separation processes. Commercial examples of MRT use include removal of impurity metals Cd, Cu, Ni. Fe, and Pb to mg L-1 or lower concentration levels from Co streams to produce battery-grade Co. Highly purified Co is required for optimal function of lithium ion rechargeable batteries and superalloys associated with aerospace and gas turbine operations. Impurity metals are recovered for reuse or proper disposal rather than being discarded to landfill. Green chemistry processes, such as MRT, are needed in metal separations going forward into the 21st century to achieve global metal sustainability in processing of native ore and treatment of secondary sources.INTRODUCTION Maximizing efficiencies of metal separations and optimizing metal recovery rates during separation processes are important goals on the road to achieving metal sustainability. Achievement of these goals is consistent with stated principles of green engineering (O'Connor, Zimmerman, Anastas, & Plata, 2016) and green chemistry (Anastas & Eghbali, 2010). Molecular Recognition Technology (MRT) separation processes using SuperLig® resins have a 25-year record of performing competitive, commercial metal separations with metal recovery rates approaching 100% (Izatt, Izatt, Izatt, Krakowiak, & Bruening, 2017). SuperLig® resins are characterized by high selectivities for specific metals over concentration ranges from g L-1 to mg L-1 or lower. MRT systems use no solvents and are simple in design and operation resulting in reduced capital and operating expenses."

Jan 1, 2017

By T. Johnson, K. Lambrych, D. Kelley

Materials for construction of equipment used in hydrometallurgical plants are selected based on a combination of their ability to perform as required in aggressive process environments as well as their cost. As a material of construction, fiber reinforced plastic (FRP) has been shown to provide equal if not improved durability relative to alternative materials such as corrosion resistant alloys at a considerably lower cost. This is particularly true in the case of equipment used in acid leaching processes for copper, cobalt, nickel and rare earth elements. The selection and extensive use of FRP over alloys in new hydromet plant construction in North and South America illustrates this advantage of FRP effectively. This paper will compare corrosion performance and cost of plant equipment fabricated with stainless steel alloys and FRP made with Epoxy Vinyl Ester thermoset resins. Real world case histories for FRP piping, storage tanks, extraction vessels, and electrowinning cells combined with laboratory based corrosion studies will be reviewed to demonstrate how FRP materials are selected for hydrometallurgical equipment.

Jan 1, 2015

"Pilot plants for pressure hydrometallurgy represent special design and project execution challenges. Over the past twenty years, Zeton has designed and fabricated a variety of world-class pressure hydrometallurgical pilot-plant facilities for the nickel industry, and this paper discusses design considerations and strategies related to such projects. Project execution methods are also discussed, and guidance is given for the selection of materials of construction and for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical pilot equipment. The paper concludes with a discussion of the need for process similarity with future commercial operations and the realities of pilot-scale equipment.INTRODUCTION The process technology developer or owner and the designer/fabricator of a new pilot-plant facility are faced with some difficult technical choices even after the decision to build a dedicated plant has been taken. A pilot-plant project is usually on the critical path of a large commercial project involving investments many multiples greater than the capital cost of the pilot plant. Schedule savings in the design, manufacture, and commissioning of the pilot plant or in a rapid completion of the experimental program can be disproportionately beneficial to the overall development project. However, inappropriate shortcuts resulting in major oversights can be disproportionately problematic. A number of considerations and suggestions for both the project execution approach and the process engineering design of pressure hydrometallurgical pilot-plant facilities are presented as a guide for potential owners and operators of new pilot-plant equipment and facilities. These suggestions are particularly applicable to the nickel industry, where the majority of our firm’s prior hydrometallurgical experience was obtained. This paper is an update to an earlier publication (Martin, 2004), offering an opportunity for a new generation of metallurgists and engineers to learn the specialist requirements of pilot- and demonstration-scale plant design, which are key functions in the development and commercialization of new processes."

Jan 1, 2017

By A. Blackmore, A. Lamoureux, J. Woloshyn

This paper provides an overview of recent applications of Computational Fluid Dynamics (CFD) to combustion related fugitive emissions problems. The aim is to illustrate the capabilities and discuss the present limitations in this field. Examples include design of retrofitted NOx reduction technology in a kiln and in a boiler, and the prediction of pollutants such as SO2 and metallurgical dust emanating from a copper flash smelting furnace. It is demonstrated that CFD is an effective tool for reducing technical risk in design, for identifying the root-cause problems and testing solutions, and for concurrently assessing emissions reduction and process impact. In addition, the value of CFD for demonstrating due diligence for regulatory compliance is discussed.

Jan 1, 2015

By S. Yue, P. Vo, M. Jahazi

The flow behaviour and microstructure development of a near-alpha titanium alloy during beta working has been investigated. Typical cogging conditions were simulated through compression testing of IMI834 at temperatures of 1025°C-1100°C, strain rates of 0.01 s-1 - 1 s-1 and post-deformation heat treatments up to 4h. Using a synthesis of available literature models, a finite element model has been developed and validated through quantitative measures of flow stress-strain data and beta grain characteristics. Flow behaviour was analyzed through a self-consistent method while the microstructure development was considered with regard to the kinetics of beta recrystallization. Deformation at beta or high alpha/beta working temperatures (T>l025°C) produced minor flow softening with complete grain refinement achieved through metadynamic recrystallization.

Jan 1, 2006

By H. Saeedi Ali, A. J. Monhemius

"Anglo Asian Mining’s Gedabek mine is situated in the Lesser Caucasus mountains in Western Azerbaijan. The ore body is a complex copper-gold porphyry deposit, comprising intermixed oxidized, transition and sulphidic gold and copper-bearing ores. Gold in the sulphide ores is generally not refractory and is recoverable by cyanide leaching, but the secondary copper minerals, which are also cyanide soluble, lead to high cyanide consumptions. Ore processing at Gedabek is by agitation leaching for high grade ore (>1g Au/t) and heap leaching for lower grade ore. In order to cope with the high copper concentrations in the cyanide leach liquors, a unique combination of resin-in-pulp for selective gold extraction and SART processing for copper removal and cyanide recovery is used. In 2015, a flotation plant was added to treat the tailings from the agitation leach plant before the tails are sent to the tailings dam. This plant produces a copper sulphide flotation concentrate and also recovers some of the residual gold and silver in the tailings. Since February 2017, due to lower grades of gold and higher copper in the feed ore, the decision was taken to alter the flow sheet and to carry out flotation ahead of agitation leaching, to reduce the cyanide consumption during leaching by removing soluble copper minerals. The paper compares and contrasts the performance of the plant in the two configurations, namely, (i) leaching followed by flotation and (ii) flotation followed by leaching.INTRODUCTION In May 2009, Anglo Asian Mining started open pit mining for gold on its Gedabek property in the Lesser Caucasus Mountains in western Azerbaijan. Gedabek is situated on the highly mineralized Tethyan Belt that runs from the Himalayas to the Balkans. The ore body at Gedabek is a complex copper-gold porphyry deposit, comprising intermixed oxidized, transition and sulphidic gold-bearing ores. The sulphidic ores contain mainly pyrite and chalcopyrite, with some secondary copper sulphide minerals, such as bornite and chalcocite, and minor amounts of sphalerite, galena and tetrahedrite. Gold in the sulphide ores is generally not refractory and is recoverable by cyanide leaching, but the secondary copper minerals, which are also cyanide soluble, lead to high cyanide consumptions and passivation of free gold."

Jan 1, 2017

By Christiaan Zeilstra, Jan van der Stel, Koen Meijer, Gerard Louwerse, Tim Peeters

The steel industry is producing about 5% of the world wide CO2 emission. Therefore the European steel industry has defined a research program to reduce the CO2 emission by 50% per ton: ULCOS. Since its start in 2004 ULCOS has identified four technologies for further development. Two of these technologies which produce liquid hot metal are discussed. The ULCOS blast furnace is based on recycling of decarbonated topgas and the capture and storage of CO2. The concept has been demonstrated during three campaigns at LKAB EBF in Luleå, Sweden. The smelting reduction process HIsarna is a combination of the cyclone-technology and Hismelt. The process has been demonstrated successfully in four campaigns at a pilot installation on the IJmuiden steelmaking site.

Jan 1, 2015

By C. Tissot, R. Palmer

"Due to the low concentrations of gold, direct measurement of gold concentration in ore on belt has not been seriously considered to now. Pre-concentration or sorting strategies have largely consisted of particle sorting based on secondary characteristics such as colour, which can be successful in select cases. CSIRO has produced sample measurement results using gamma activation analysis of ~300 gm samples with accuracies of around 30 ppb at best. With this encouragement, a feasibility study into gold ore measurement on belt for the purpose of sorting pods of gold ore has been undertaken. The study described here included, prototype design options with existing industrial Linacs, extensive Monte Carlo modelling of measurement sensitivity and shielding, further sample measurement, a study of the interaction of target measurement accuracy and sorting efficiency, and a rough estimation of potential economic benefit. The projected model sensitivity of around 0.1-0.15 ppm (1 standard deviation) in 10 seconds for 1 ppm average feed result in good bulk sorting performance and intriguing economic potential.INTRODUCTION Pre-concentration or sorting strategies for gold ores have largely consisted of particle sorting based on secondary characteristics such as colour or density, which can be successful in select cases (Klein, 2010). No method is available to measure gold content for sorting in particles or even in bulk on belt, principally due to the low concentrations of gold present. In fact, in many cases it is difficult to do rapid bulk grade measurements of base metal ores with concentrations many orders of magnitude higher. By a fortunate quirk of nature gold is particularly amenable to gamma activation analysis (GAA). CSIRO has performed extensive work in GAA of samples of crushed ore (Tickner, 2017). This has resulted in the Photon AssayTM technique that is currently being commercialised through the CSIRO spinoff company Chrysos. The technique relies on the recent availability of industrial high intensity X-ray sources such as Linacs which are currently being used in industry for security, medical and sterilisation applications. This development has led to CRC ORE funding a feasibility study to determine whether on-belt measurement of gold concentration is possible at a rate and accuracy sufficient to be useful for bulk sorting, where pods of ore are diverted rather than individual rocks. The study in the first instance is based on Monte Carlo modelling that has successfully predicted the performance of the sample based gold measurements. As well as the measurement feasibility consideration was also given to the likely heterogeneity of gold ores and hence the degree to which useful separation could be achieved. This is then tied to a back of the envelope evaluation of the order of magnitude economics of bulk sorting in an example deposit."

Jan 1, 2017

By Kevin P. Plucknett, Z. Memarrashidi

"In the current work, factors influencing the corrosion mechanisms of TiC and Ti(C,N) based cermets are reviewed. Cermets were typically prepared with 30 vol.% of metal binder, in the form of various in-situ reaction-formed Ni3Al alloys. Commercial WC-Co hardmetals were also examined as baseline materials. The assessment of corrosion involved a variety of electrochemical measurements, including open circuit potential and potentiodynamic polarisation. The corrosion potential and current density were determined, following Tafel extrapolation, allowing estimation of the corrosion rates. Post-corrosion characterisation involved scanning electron microscopy analysis and associated energy dispersive X-ray spectroscopy of the sample surfaces. It is demonstrated that the primary corrosion mechanism for this type of cermet is dissolution of the metallic phase during oxidation attack, and thus this response can be expected to increase with the amount of binder in the cermet, although degradation can be subtly affected by composition (i.e. alloy composition, C:N ratio, impurities in the ceramic phase, etc.) and test procedure (i.e. aerated vs. de-aerated electrolytes). It was observed that addition of N content into the ceramic phase is beneficial to the corrosion characteristics of TiC based cermets, through significant refinement in the grain size of the hard phase. Similarly, elimination of impurities, such as W in selected TiC powders, also improves the corrosion resistance.INTRODUCTION Cermets are prepared using the combination of a hard, high elastic modulus ceramic phase with a ductile, high toughness metallic binder. This pairing of hard and ductile components ensures wide application of cermets in demanding wear environments. These materials are consequently used industrially in both bulk and coating form. The most common example of such a composite system is based on the use of tungsten carbide with a cobalt-based binder (WC-Co), which has been widely examined over the past 80 years. However, while WC-Co has been shown to exhibit an excellent combination of high strength and wear resistance, the corrosion and high temperature properties of this material are relatively poor. In addition, WC-Co possesses a high density (~13–14 g/cm3), which makes it a less desirable option when the component mass is a design factor (i.e. use in aerospace). In particular, the aqueous corrosion response of WC-Co limits its use in wear environments where combined corrosive degradation may occur (i.e. tribo-corrosion scenarios). Alternate cermet systems are therefore being actively developed due to these performance limitations."

Jan 1, 2017

By C. Piribauer, E. Feichtenhofer, A. McEneaney

"As part of a major diversification project, RHI AG, through its plant in Drogheda Ireland, has developed a Caustic Calcined Magnesium Oxide (CCM) for use in the Cobalt (Co) & Nickel (Ni) hydrometallurgical extraction industry. In the course of the project, the company investigated the chemical and physical properties of a number of different Magnesia’s used in Co & Ni hydrometallurgy applications and has been able to determine the important parameters for a successful Magnesia for this application. A number of live plant trials have confirmed the results of this testwork and the company is now proceeding to produce this product in commercial quantities at Premier Periclase Ltd., the RHI AG plant in Drogheda, Ireland. This paper will outline the development work conducted by the company and highlight the important chemical and physical properties that make a successful CCM. Much of the research was conducted at the RHI Technology Centre in Leoben, Austria. In addition, a number of external laboratory studies were conducted on behalf of RHI AG. The result of this work has allowed the company to develop a Magnesia product with optimised properties for use in the Cobalt and Nickel hydrometallurgical extraction process.INTRODUCTION Premier Periclase is part of RHI AG, a globally operating supplier of refractory products, systems and services, headquartered in Vienna, Austria. The company produces Magnesia from seawater at its plant in Drogheda, Ireland. While the main focus is on production of refractory grade Dead Burned Magnesia for the steel industry, the plant also produces a number of different grades of Caustic Calcined Magnesia as well as Magnesium Hydroxide products. As part of a major project to diversify the company’s product base, the use of CCM in the Cobalt (Co) & Nickel (Ni) hydrometallurgical extraction industry was investigated. One of the company’s highly reactive grades of Caustic Calcined Magnesia was found to be particularly suitable for this application. In an effort to understand what makes a successful Magnesia for hydrometallurgy the chemical and physical properties of different Magnesia’s used in Co & Ni hydrometallurgy were investigated. This paper and conference presentation outlines the findings of this process."

Jan 1, 2017