Search Documents

This paper describes results of an investigation of fracture during tube expansion of 5052 and 5754 aluminum seam-welded tubes to optimize the forming of aluminum tubes during hydroforming. The tubes were produced in laboratory by press forming of tubular blanks and pilot-scale high frequency induction welding. The effect of property mismatch between the weld and base metal has been investigated. The material work-hardening was obtained by roll forming of sheet blanks in the 0-temper and H32 temper condition. The results showed that a significant work-hardening can be present in aluminum tube without causing weld fracture during tube expansion. The work-hardening increases the yield-strength mismatch between base metal and weld. Annealing reduces the hardness of base metal leading to more uniform deformation during tube expansion. As a result the occurrence of weld fracture is reduced. The study showed significant deformation of the welds during tube expansion. Weld thinning can be as large as parent-material thinning before fracture. To avoid fracture at the weld joint, good formability and high yield strength of the weld is needed. FEM simulation showed that minimizing the width of the weld joint can reduce thinning of the weld.

Jan 1, 2004

By M. J. Gagnon

The agglomeration of particulate materials is used in many mineral processes to enhance the settling of the fine particles, Depending upon many physical and chemical parameters, the aggregates demonstrate specific density-size distributions, In this study, a fractal model of the agglomeration process is introduced, Based on reliable experimental data and on physical calculation, the model presented helps to envisage the initial formation of the micro-flocs, and to interpret the subsequent interactions between the aggregates in terms of either coagulation or flocculation, Data from different sources, materials and different agglomeration processes are analysed and compared in the light of the proposed model.

Jan 1, 2005

By E. Herrera, L. Mariscal

"Ilo Copper Smelter operates since 2007 with an ISASMELTTM furnace as a single smelting unit (1,200,000 tpy) associated with two Rotary Holding Furnaces for separation of matte and slag, and which directly produces a discard slag. Southern Peru continually has been improving the slag chemistry of its ISASMELTTM furnace in order to reduce copper losses, given its big economic impact due to large slag mass generation. The present paper describes the influence of the CaO, Al2O3 and magnetite content in the slag of the ISASMELTTM furnace correlated with the SiO2/Fe ratio and its liquidus slag. Also it defines the best slag chemistry and operating practice in order to reduce the copper losses without compromise the bricks life of the furnace.INTRODUCTIONIlo Copper Smelter of Southern Peru (Grupo Mexico) is located on the southern coast of Peru, and treats mainly copper concentrates produced in its own mines (Toquepala and Cuajone).The modernized smelter was commissioned in 2007 and operates with an ISASMELT™ furnace as a single smelting unit (1,200,000 tpy), which is associated with two Rotary Holding Furnaces (RHF) for separation of matte and slag. This slag is directly sent to the dump. Figure 1 shows the smelter flow diagram.The ISASMELT™ process is a bath-smelting process using a single lance. The lance tip is immersed into a molten slag bath contained within the stationary, vertical, refractory-lined ISASMELT™ furnace. The injection of oxygen-enriched air, through the lance into the slag results in a highly turbulent molten bath. Feed material falling into the turbulent bath from above reacts rapidly, resulting in extremely high productivity for a relatively small bath volume."

Jan 1, 2012

By V. ?. Chanturiya, G. P. Dvoychenkova, ?. Ye. Kovalchuk

"Several mineralogical investigations have revealed the composition of modified kimberlites and the mud generated during treatment of diamonds, which contains up to 50% clay minerals (e.g., talc, talcsaponite, chlorite-saponite, Na-saponite) and X-ray amorphous phase. We investigated the composition of the natural diamond surface in relation to the diagnosed minerals and established the sequence and conditions for mineral formation on the crystal surface under kimberlite processing conditions. This article suggests a method to destroy and further dissolve minerals on the crystal surfaces using water system electrolysis products, which makes it possible to restore the diamond hydrophobic properties. The application of chemically treated water in the foam separation cycle under the conditions of high recovery of diamonds made it possible to increase the content of the factory concentrate by 8.0%.INTRODUCTIONThe high content of the modified minerals in the kimberlite ore results in the formation of hydrophilic slicks on the surface of the crystals which decreases the diamond’s hydrophobic properties and increases the losses thereof in the process of grease and foam separation to 20-30% (Kurenkov, 1957; Chanturiya et al., 1998, 1999, 2005; Duikarev et al., 2000).The previous researches have revealed the fact that the prospective way of solving the problem of intensity of mineral impurities formation on the surface of the crystals and the increase of concentration parameters is reached due to application of physical and chemical stimulation techniques on the solid and liquid pulp (Stricland-Constable, 1971; “Improvement of the technology…”, 2006; Makarskii, Adodin & Tarasova, 2011; Chanturiya, Dvoychenkova & Trofimova, 2012). However, the main task of investigations to stipulate the objective achievement is the studying and justification of the reasons of the diamond surfaces covering by the mineral slicks"

Jan 1, 2016

By S. Y. Mostowy, P. W. M. Shibley

"When Texas Gulf Sulphur Company discovered the Kidd Creek ore body in 1964, a crash program began almost immediately for the design and construction of a modern concentrator. It was necessary to mill two distinct ore types; one containing copper and zinc, the other lead, silver and zinc minerals. The final concentrator design was to handle 9,000 tons of ore daily in three circuits. One circuit was to treat copper-zinc and another lead-zinc ore exclusively on a permanent basis. A central circuit was designed with adequate flexibility to treat either of the above ore types in accordance with planned mining schedules. Ecstall Mining Limited, a wholly owned subsidiary, now operates the mine and concentrator complexes for Texas Gulf. The mine is located 15 miles north of Timmins and the concentrator 15 miles to the north-east along Highway 101. The ore is hauled from the mine to the concentrator over a 17-mile railroad. Initial milling operations began in November, 1966.1 - ABSTRACTThis paper deals with bulk reagent handling at the Kidd Creek concentrator. The reagent section at Kidd Creek has operated excellently since milling began in 1966. The bulk handling techniques are satisfactory. They have contributed substantially to good working conditions, economical practices and metallurgical efficiencies. The bulk handling features described should be considered in existing and proposed concentrators."

Jan 1, 1970

By M. Jiang, X. Fan, W. X. Chen, Z. K. Guo, H. H. Zou

"Some improvements are carried out for elasto-plastic model by taking the shear dilation effects and relaxation effects of deep rocks into accounted. The high pressure equations of states with Mie-Grüneisen form are also introduced to describe the relation of pressure-volumetric strain. Numerical simulations of free field responses for deep underground explosions are conducted by using the user subroutines which compiled by means of the secondary development functions of LS-DYNA9703D codes. It is indicated that the dynamic responses of free field are well simulated based on this improved elasto-plastic model, and the analytical results are in good agreement with the data of U.S. Hardhat nuclear test.INTRODUCTIONDynamic behaviors of deep rocks for underground explosions are obviously different from that of shallow underground explosions and have aroused great attentions of international experts who work for rock engineering. The dynamic models of deep rocks could be roughly divided into classic elasto-plastic model and fracture damage model according to different theoretical foundation. M. E.Kipp and D. E.Grady et al. are the outstanding representatives who engaged in the researches of fracture damage mechanics. Researches of dynamic problems for geomaterials were carried out by C.C.Grigorian and the conclusion that incompressible elasto-plastic medium model could not be used to solve the problems of closed underground explosion was derived, and therefore C.C.Grigorian model was proposed. In this model, C.C.Grigorian assumed that the average hydrostatic pressures and the densities of medium had one to one relationship, and the path of loading or unloading is different from each other. For shear deformations, analytical solutions of the problems were derived according to the model which was slightly different from Prandtl-Reuss model, the constitutive equations were closed by Mises-Schleiher constitutive model. However, the analysis showed that there were two inadequacies in C.C.Grigorian model. Firstly, the shear dilation effects of fractured medium after wave front could not be considered. Secondly, the relaxation characteristics of the rocks in fractured region were not taken into account."

Jan 1, 2015

By Anthony A. Zoobkoff

Gotcha! ? What Did I Just Agree To? ? You can?t repeat or use anything you heard. ? Did you agree before you knew what you were going to be given, told or shown? ? If you knew what you were to be given, told or shown, would you have still agreed?

May 1, 2013

By B. Dubreuil, J. -M. Lalancette, D. Lemieux, C. Chouinard

The extraction of gold and silver has been examined via the use of mixed halogens: chlorine and bromine. The reaction was performed in a brine of sodium chloride with a small amount of sodium bromide at 40-50°C, in an atmosphere of chlorine, at atmospheric pressure. The process takes advantage of the very high reactivity of bromine towards gold, while the higher oxidation capacity of chlorine leads to gold chloride as end product with recycling of bromine. Fast reaction rates are observed along with gold recovery at the level of 95%. Chlorine-consuming common elements are removed prior to chlorination.

Jan 1, 2011

By I. E. Puddington, F. W. Meadus

The beneficiation of barite in mill tailings using an agglomeration technique has been demonstrated. Barite was selectively absorbed from a conditioned aqueous slurry into a collector oil by mechanically mixing slurry and oil. The resulting oil-bonded barite-containing agglomerate was washed, to remove gangue material, and further mechanically contacted with dilute H2SO4 This treatment resulted in the transfer of barite into the aqueous phase. Grades as high as '97% BaSO4, with recoveries of 80%, have been obtained using this technique.

Jan 1, 1973

By J. R. Parga T., P. J. Valenzuela G., L. S. Quiroz C., P. Guerrero G., J. L. Valenzuela G.

"Pressure oxidation is a hydrometallurgical pre-treatment process used for refractory auriferous sulfide ores. In the work reported here, a refractory pyrite ore sample from the Mulatos mine, Sonora, Mexico was characterized. The sample was subjected to atmospheric cyanidation, and simultaneous pressure oxidation and cyanidation under different conditions of temperature and pressure. The mineral characterization showed that pyrite is the main species in the sample. The gold extraction tests were carried out in an 1-litre Parr pressure vessel at a temperature range of 90-120 °C, a pressure range of 87.5–150 psi (using oxygen), and a cyanide concentration range of 0.8-1.2 %wt. The gold extraction results showed that diffusion through product layer is the rate controlling step.INTRODUCTIONIn hydrometallurgical precious metals extraction, the most commonly used process is sodium cyanide leaching, as shown in the next reactions involving gold and silver (Fleming, 1992; Marsden & House, 2006):4Au(s) + 8CN- (aq) + 2H2O(l) + O2(g) ? 4Au(CN)2 -(aq) + 4OH- (aq) (1)4Ag(s) + 8CN- (aq) + 2H2O(l) + O2(g) ? 4Ag(CN)2 (aq) + 4OH- (aq) (2)“Refractory” auriferous ores or concentrates often contain gold and silver locked inside other sulfide phases such as pyrite. This renders cyanidation ineffective, so oxidative pre-treatments are used in order to convert the sulfide minerals into porous oxide minerals and make cyanidation work more efficiently. Reaction (3) shows the oxidation of pyrite in alkaline media and the formation of the porous oxide (Koslides & Ciminelli, 1992):2FeS2 (s) + 15/2 O2 (g) + 8H- (aq) ? Fe2O3 (s) + 4SO4 2- (aq) +4H2O(l) (3)A process of simultaneous chemical pressure oxidation and cyanide leaching for a flotation concentrate produced in the mine of Bacís, Durango, in Mexico, gave good results (Parga et al., 2007). In the study presented here, it was intended to use this treatment for a refractory pyrite mineral from the Mulatos mine in Sahuaripa, Sonora, Mexico, modifying variables such as pressure, temperature and cyanide concentration to find the best conditions for oxidation and leaching."

Jan 1, 2012

By A. K. Verma

This paper provides a brief overview of evolution of deformations, stresses, and pore pressures due to different excavation stages during construction of an URL. Excavation of a rockmass develops a damage zone of finite width around the excavated zone which is associated with changes in permeability and which affects the fluid flow mechanism. In this study, a coupled hydromechanical (HM) analysis has been conducted for a water saturated porous rock mass which has been created by sequential excavation and backfill of vertical disposal pit of an URL. For this purpose, an Atomic Energy of Canada Limited?s in-floor concept for a deep geologic repository suitable for Indian conditions has been used. Changes in rock deformations, stresses, strains and mechanically induced pore pressure in an undrained condition, during excavation, as well as those caused by mechanically induced rock deformations after backfill of the disposal pit, have been modeled. A three-dimensional finite difference tool FLAC3D has been used for the analysis.

Jun 1, 2012

By D. L. Griffith

THE realization by metallurgists of the important effect that traces of impurity may have upon the properties of a metal, and their steady demand for purer and still purer metals, have made the special cools for 'trace' analysis of increasing value. In the United States at least, spectrographic analysis is becoming the standard method for determining the impurities in zinc die-casting alloys. The Hudson Bay Mining and Smelting Company, as a producer of virtually pure zinc, uses the spectrograph to control the purity of its products, and-as the electrolytic method is employed here-to control both the impurities in the electrolyte and those 'trace' elements, which, while they do not contaminate the zinc, have a great effect on the plating efficiency. The general plan of the laboratory is shown in Figure l; the housing for air purification, which is on the roof, is indicated by broken lines. One of the chief factors affecting the layout was the easy way in which a spectrographic assay can be spoiled by contamination. To minimize the quantity of dust tracked in, the laboratory was made separate from the general research laboratories, and an office was placed between the two. This arrangement has its drawback because of the traffic through the office, but it has effectively cut down dust. For similar reasons, the available space was subdivided into a number of small rooms, and the air currents in the laboratory were so arranged that dust would be carried where it would do least harm. Air is drawn in at the roof over a 50-kilowatt bank of Calrod heaters, through Annis air filters, by a No. 4 Sirocco fan. Most of it is forced into the spectrograph room, but some goes to the office and darkroom. The air flow is from the spectrograph room, through the plate-measuring room, into the chemical laboratory, where it is exhausted by a No. 1% Sirocco fan on the fume hood. Air can also re-circulate from the plate-measuring room back to the heater. The arrangement is such that the air in the laboratory is maintained at higher pressure than the outside air; consequently, no dirt enters through cracks about the windows and doors. A thermo-regulator holds the temperature constant within one or two degrees; only on the hottest days in summer does the temperature rise enough to affect the focus of the instrument.

Jan 1, 1940

By C. Boudreault, M. Fortier, S. Fafard

In the forging industry, the increasing trend is to use DC cast billets as forging stock to replace extruded stock. However, there is little technical information available in open literature. In order to gain a better understanding of the behaviour of cast stock during deformation, a study was initiated to evaluate the impact of an homogenisation treatment on the billet prior to cold forging. Axisymmetric upsettings of cylindrical samples machined from DC billets were achieved in order to evaluate and compare flow stresses, crack initiation and propagation. Results show a 30% decrease in flow stress after homogenisation. Observations of the deformed samples show major cracking for the as-cast material. Optical microscopy and SEM observations have related the crack initiation to decohesion around ß -AlFeSi particles and subsequent growth along the constituent path. Homogenisation effectively breaks up and transforms the ß phase, present as platelets in the cast product, into smaller spherodised a-AlFeSi particles. This has the effect of preventing crack growth in the forged product. The homogenisation treatment also resulted in the reduction of Mg and Si in solid solution. The softer matrix generated 29% less die wear when compared to the as-cast structure. Based on the results of this study, it is thus recommended to homogenise cast billets prior to cold forging.

Jan 1, 2006

By Per Hedvall, Jan-Eric Ståhl

"The main objective of this study is to introduce the new Sandvik’s production cost-model within Crushing & Screening (C&S) technology. So far, there have been different ways of determining different production costs in the industry, however, the previously published and presented methods have not been very efficient in calculating the costs per product and metric ton. Accordingly, the current study has been planned and started in collaboration with Lund University to provide an accurate and easy to implement cost estimation program to determine the costs for crushing and screening plants worldwide.The proposed model has been adapted to fit the C&S processes of different rocks/ores fractions. The result is presented as cost per ton of the end product(s).Within this paper the cost estimation results for 3 different crushing and screening plants are presented based on the information obtained from the following sources: a) documents at Sandvik SRP, b) Sandvik’s crushing & screening internal/external machines/plants data and information, c) literature studies, including the use of Sandvik’s internal/external simulation and software programs, d), visiting the crushing and screening plants ,e) interviews, information systems’ data, and, f) testing and observations by ourselves.In order to improve the level of accuracy and the validity of the attained results, simplistic Monte-Carlo simulations have been used, where needed. The achieved results, so far, have proven the reliability of the model. The calculated cost estimations have shown an accuracy over 80% when they compared with real cost data obtained from plant practices.The current cost calculation model, will offer the possibility of:•,Calculating the production costs in proposed and/or existing C&S plant.•,Making detailed cost analyses for the end product(s) in proposed and/or existing C&S plants.•,Determining the profitability of each finished product when it’s required.•,Cost optimization by potentially cutting the cost for part of C&S plant with an existing plant practice"

Jan 1, 2016

By ManhKha Trinh, Neal Pyke

Dofasco was the first company to adopt oxygen steelmaking in North America in 1954, two years after the first LD vessel installed and operated successfully in Linz, Austria. Since then, Dofasco has investigated and implemented several strategies to maximize hot metal usage and minimize overall cost. Some key strategies -low hot metal silicon, combined blowing conversion, vacuum degassing tank upgrade and BOF slag carryover control - are discussed. Post combustion, scrap preheat, carbon injection trials along with current operating philosophies are described.

Jan 1, 2004

By J. Sadaki, G. Dodbiba, S. Murakami, T. Fujita, S. Matsuo, H. Ono, K. Okaya

Printed circuit boards (PCBs) from discarded personal computer (PC) and household appliances were crushed by mechanical crushing or water explosion to remove mounted parts. More parts were stripped from PCB for PC composed of epoxy resin than from PCB for household appliance composed of phenol resin. In an attempt to raise the copper grade of PCB by removing other components, a carbonization treatment was investigated. The crushed PCB without surface-mounted parts was carbonized under a nitrogen atmosphere at 1073K. After screening, the char was classified by size into oversized pieces, undersized pieces and powder. The copper foil and glass fiber pieces were liberated and collected in undersized fraction. The copper foil was liberated easily from glass fiber by stamping treatment. On the other hand, tantalum capacitors were collected from mounted parts. The tantalum-sintered bodies were separated from molded resins by heat treatment at 723 to 773K in air atmosphere and screening of 0.5mm. Silica was removed and 70% of tantalum grade was obtained after more than 823K heating and separation.

Jan 1, 2011

By J. A. Hillier

"IntroductionThe purpose of sampling is to remove a portion of material from a stream which is representative of it in size, moisture and mineral content.To prevent the effects of segregation, generally caused by the way in which a conveyor, pipe or launder is loaded or directed, the sampler should cut proportionally the entire cross section of the stream.If one conveyor transfers to another at a right angle, fines may be dropped on the near side, and the coarse material thrown to the opposite side. Segregation can also occur as a result of the motion of a conveyor belt passing over the idlers causing the coarse material to roll to the sides of the belt.When slurry changes direction of flow in a launder or pipe, the heavier and coarser fraction will centrifuge to the outside of the curve and tend to remain on one side of the stream. Similarly, if two streams joining in a common launder are not mixed at the point of confluence, they will continue down the launder unmixed . This effect is particularly noticeable in a plastic lined launder.Therefore, a proportional sample is usually accomplished by a constant rate of cutter travel across the entire stream, making certain that the cutter is not full or splashing over before reaching the end of travel.The cutter should operate on a constant interval based on time, tonnage and uniformity of flow. The opening should be at least three times the width of the largest piece to be sampled. The cutter width is more critical with ore samples where particle sizes are large. With slurry samples, the opening is usually much larger than the minimum in order to obtain sufficient samples"

Jan 1, 1989

By Norman B. Davis

Introductory Feldspar is one of the most important mineral products consumed by the various branches of the ceramic industry. In the manufacture of table ware, electric porcelain, floor tile, and enamels, it supplies the chief fluxing ingredients necessary to bond the other more or less inert materials together when moulded into desired shape and fired in a kiln. Feldspar is used in the manufacture of bottle glass as a means of introducing alumina in a form easily assimilated. It is also used in certain scouring soaps particularly designed for cleaning enamel and glass surfaces. Feldspar, as it finds its way to the trade, is not a single mineral but is rather a mixture of various proportions of the feldspar silicate series, either in natural intergrowth or blended in the milling process, to produce a desired result. It is often further modified by the presence of quartz in amounts up to 30 per cent. The table on the next page gives typical commercial analyses of feldspar from various sources. Canadian feldspar produced to date has consisted mainly of the high-potash, relatively low-soda, variety, and has enjoyed a good market in the United States for the manufacture of enamels, electric porcelain, and vitrified table-ware. About eighty per cent of the output has been exported to the United States, but, with increased milling facilities in Canada and changes taking place in domestic United States sources of supply, the proportion exported will be reduced next year.

Jan 1, 1931

By J. B. Hamilton

The advantages of generating and distributing electrical energy direct from the coal-fields so closely affects the mining industry that a few remarks on the unbalanced phases of coal distribution is worthy of attention. The value of coal imported into Canada from 1912 to 1921 exceeded the sum of $580,000,000. In 1922 Ontario imported 1,640,000 tons of anthracite and 9,440,000 tons of bituminous coal. I submit that the use of Saskatchewan lignite in an electrical super-power plant equipped for the carbonizing of coal, and disposal of excess gases would be the commencement of a solution of the fuel shortage in Ontario. As Saskatchewan becomes more and more populated and manufacturing increases, the amount of by-product carbonized fuel available for shipment to Ontario will increase, and its shipment to that province would decrease the trade deficit of the national balance sheet. If and when this is carried out it will mean a better and wider market for Alberta fuels in Saskatchewan and Manitoba.

Jan 1, 1924

By J. M. Harrison

"The Nor-Acme gold mine is near the shore of Snow lake, northern Manitoba, about 75 miles east of Flin Flon. The claims that form the nucleus of the present property were staked in 1927 by C. R. Parres, but it was not until 1941 that diamond drilling disclosed the potentialities of the deposit. In that year a large-scale drilling programme was begun under the direction of F. Ebbutt, of the Howe Sound Exploration and Development Company. Two orebodies were outlined containing about 5,000,000 tons of ore assaying $5.25 in gold per ton. In August, 1945, construction of the mining plant was begun.All information and interpretations contained in the following brief description of the deposit were obtained from surface mapping.GEOLOGYThe ore lies at the contact between a coarse, basic, pyroclastic rock, which is the hanging-wall, and grey, acidic lavas and sediments, which form the footwall. These rocks are cut by irregular basic intrusions that vary in composition from diorite to hornblendite, and by small acidic dykes . Tourmaline is locally common in the hanging-wall rock near the ore.The ore occurs in brecciated, silicified, and ·slightly carbonatized rock. Arsenopyrite is the main sulphide and the gold is associated with it. Pyrrhotite is locally abundant and minor pyrite, chalcopyrite, sphalerite, galena, and cubanite have been noted. Two orebodies are known, the Dick and the Toots. The Toots, which is much the smaller of the two, is about 1,000 feet west of the Dick."

Jan 1, 1954