Search Documents

By C P. Gravenor

In 1953, a deposit of sedimentary oolitic iron ore was discovered in the Clear Hills area of northwestern Alberta. Since that time, detailed drilling has outlined reserves in excess of 200 million tons of ore grading 30 to 35 per cent iron. Attempts to physically beneficiate the ore to meet blast furnace or direct reduction feed specifications have been, in general, unsuccessful. In 1960, Premier Steel Mills Limited and the Research Council of Alberta jointly sponsored a pilot-plant test at the R-N Corporation at Birmingham, Alabama. About 5,000 tons of ore were treated, and briquettes containing 90 per cent Fe were produced, with 83 per cent recovery. At the same time that the R-N tests were being made, the Research Council initiated a program to produce high-purity powders by chemical methods. Several purification techniques were investigated; hydrochloric acid dissolution of reduced ore was finally adopted. Briefly, the steps involved in this acid process are as follow

Jan 1, 1964

By S. Feinstein, I. Reznik, Y. H. Hatzor, O. Shitrit, Y. O. Rosenberg, H. J. Vinegar, S. Nguyen

"We report the effects of porosity and total organic carbon (TOC) content on the mechanical behavior of organic-rich chalks, based on laboratory measurements. The organic-rich chalks are from the Senonian Ghareb and Mishash formations. This deposit is an immature oil-prone source rock, about 300 meters thick, situated at shallow depths (several hundreds of meters) in the Shefela basin in central Israel. The study is based on core data collected from the Zoharim borehole.Three main phases comprise the bulk volume of this rock: 1) carbonate mineralogical phase (predominantly calcite); 2) pores (mostly saturated with brine); and 3) solid organic phase (type IIS kerogen). The mechanical effects of porosity (23-45%) and TOC (4-19%) are evaluated based on bulk incompressibilities vs. volumetric fractions analysis. Volumetric fractions of mineralogical and organic phases were obtained by porosity, density and TOC measurements. Saturated rock bulk moduli were measured through ultrasonic velocity measurements. Saturated rock bulk moduli correlate best with the sum of kerogen and pore volume fractions, rather than each of them separately. The volumetric fractions were also used to define the range of bulk modulus of the organic-rich chalk, using the Hashin-Shtrikman upper and lower bounds. Based on Marion's Bounding Average Method (BAM), the normalized stiffness factor of the chalk averaged at w=0.197, indicating a soft pore geometry. Using the average normalized stiffness factor, the BAM predictions showed excellent match with the saturated rock bulk modulus and the sum of kerogen and pore volume fractions. Based on our findings, it is inferred that kerogen grains do not support the solid skeleton but are distributed between the minerals grains. We also propose here a straightforward approach for calculating the Hashin-Shtrikman bounds, based on TOC and porosity measurements. The mechanical effects of porosity and TOC indicated here are very important for the understanding of the influence of immature kerogen presence in highly porous chalks, as the Ghareb and Mishash formations."

Jan 1, 2015

By G. Hu, P. Chang

"As hydraulic fracturing is forbidden in some countries due to its accompanying environmental pollutions, microwave fracturing was proposed as a substitute technology to enhance coal seam permeability. Its mechanism includes: on the one hand, thermal stress caused by non-uniform microwave heating leads to fracture development in coal body, which increases coal seam permeability for gas; on the other hand, moisture within the coal body that hinders gas desorption and diffusion is removed during this process. To study the effect of moisture content on fracture development under microwave irradiation, high resolution photographs were taken before and after microwave treatment. These photographs were then binarized and skeletonized. Based on the processed photographs, the total area were calculated using ImageJ. The results showed that coal samples with 0% and 25% water saturation have more variation in fracture development as compared to that of samples with 50%, 75% and 100% water saturation. This study can be very useful in gas drainage and gas control in coal mines. INTRODUCTION Coalbed methane (CBM) is a clean energy source as well as a natural hazard to underground mining (Kurnia, Sasmito, & Mujumdar, 2014; Ranathunga, Perera, & Ranjith, 2014). One of the main goals of mine ventilation is diluting methane and removing underground contaminants (Xu, Huang, Nie, Chalmers, & Yang, 2017). Coalbed methane (CBM) has to be extracted prior and during underground mining to avoid methane outburst and explosion accidents. However, with the increase of mining depth, the coal permeability decreases significantly, which makes it hard to extract the methane (Huang, Xu, Hu, Kizil, & Chen, 2018). To enhance the coal seam permeability, many CBM recovery methods have been applied on-site, such as hydraulic fracturing and enhanced coalbed methane (ECBM). However, hydraulic fracturing is restricted due to environmental concerns and ECBM is only suitable for the coal seam with relative large permeability (Bustin, Bustin, Chikatamarla, Downey, & Mansoori, 2016; Huang, Xu, Chen, & Chen, 2018; Huang, Xu, Hu, et al., 2018)."

Jan 1, 2019

By Reinis Sipols

AGENDA ? Introduction ? Definitions and Key features ? PEA - Preliminary Economic Assessments ? PFS ? Preliminary Fesibility Studies ? FS ? Feasibility Studies ? Costs and Risks ? Cash Flow, Economic Analysis and Reporting ? Recommendations for Improved FS accuracy INTRODUCTION ? The reporting of material information on mineral deposits has been governed by NI 43-101 legislation for almost a decade. ? The investment sector depends on the independent, professional QP to provide objective observations, comments and recommendations through all levels of geological, engineering and financial evaluation until a mine construction decision has been made.

May 1, 2013

By X. Wu

Tunnel Boring Machines (TBMs) are widely used for tunneling in urban areas because of their high advance rate, precise as-built profile and minimal impact to buildings and traffic on the ground. For a tunnel built by a TBM, there are strict requirements on alignment control and safety. To meet these requirements, it is important to monitor the position of the TBM. In the current practice, the TBM position data, including advance distance and line and level deviations, are reported manually to the managers on a daily basis. To interpret and analyze the position data, the managers also need to refer to various construction drawings. This practice is untimely, inefficient, and error prone for decision making. To improve the current practice, an automatic approach for real-time as-built tunnel product modeling and visualization is proposed, based on TBM position and orientation data autonomously sourced from the Virtual Laser Target Board (VLTB) TBM Guidance System developed at University of Alberta. Related information of the tunnel project, such as the as-designed alignment, soil layers, the ground, existing utility lines, is also visualized together with the model of the as-built tunnel. The modeling algorithm is presented step by step. Its application in a real-life drainage tunnel project is discussed and limitations are also identified.

Aug 1, 2013

By L. B. Kilius

The composite cathode system based on Ce0.9Gdo.1O2_,5 electrolyte with a painted cathode was used for an intermediate temperature (500-700°C) solid oxide fuel cell. This cathode system was chosen due to its excellent thermal expansion match to the electrolyte, its relatively high conductivity (115 S cm-1 at 700°C), and its low activation energy for oxygen reduction (99 kJ/mol). It was found that the decrease of sintering temperature of the composite cathode system produces a significant decrease in charge transfer resistances to a level of 0.25 SI cm2. The conductivity measurements of porous samples produced values between 40 and 88 S/cm for porosities of 30-40%.

Jan 1, 2005

By R. W. Lawrence, O. Lopez

Many gold deposits in the world have not been developed clue to the presence of copper and other base metals which can cause metallurgical and environmental challenges clue to the formation of base metal cyanide complexes. SART technology (sulphidization-acidification-recycle-thickening) can resolve these issues by recovering copper as a high grade sulphide concentrate, recycling the associated cyanide back to the gold leach, and eliminating the downstream environmental liabilities. Project economics can be improved substantially, leading to a positive re-evaluation of new and existing gold-copper projects. Some aspects of the design and operation of two recently commissioned SART plants will be discussed.

Jan 1, 2011

By J. ?H. Chen

Remote sensing technologies have been applied to numerous fields and already benefited those in improving efficiency and recognition accuracy. Change of streamflow can be devastating to residents living along riversides. Still it is difficult to detect such deathly change in large area scale by traditional field surveys. The research aims at provision of detecting streamflow change using a mathematic method based on remote sensing technologies. The scope is on remote sensing stream images taken during the invasion by Typhoon Morakot, bringing one of the major catastrophes to Taiwan. An algorithm was adopted to deal with streamflow recognition on RGB images. The algorithm is capable of yielding change measured by meters and illustrates how main streams shift. An practical example for the Baolai area surrounded by Laonong stream shows that the streamflow moved 88 meters (36 pixels) toward the downtown area during the invasion by Typhoon Morakot. In addition, the results highlight all dangerous zones (scouring zones) for residents to prevent further potential damage.

Aug 1, 2013

By Ralph Harris, Javier Jara

"Oxygen is essential in gold cyanidation. It is supplied to the leaching media by sparging oxygen or compressed air into the cyanidation tank. The rate of oxygen transfer is critical to achieve the desired oxygen concentration in solution.The performance of a novel device for gas sparging recently developed at McGill University is compared to the mass transfer characteristics of the two spargers most used in the gold industry: the four lance configuration and the inverted cone. The distribution of gas and the kinetics of oxygen desorption of the three types of spargers was studied in a 140 litre tank. The oxygen dissolution of the new device is three to five times faster than the other spargers. This could increase the leaching rate and/or decrease the cyanide and oxygen consumption.IntroductionIn hydrometallurgical processing, it is often necessary to bubble gas through a pulp to carry out the wanted reactions. The gas can act to agitate the pulp and it can also supply reactant. The rates of the reactions which require a reactant supplied by the gas are often dependent on the rates of mass transfer from the gas to the solution.A common example of this is gold cyanidation which requires oxygen for gold dissolution. Since the gold containing slurry is rich in other oxygen consuming substances (sulphide like pyrrhotite), it is important to provide enough oxygen to allow complete gold dissolution within the residence time of the cyanidation reactors. It has been demonstrated that the rate of gold dissolution is directly proportional to the dissolved oxygen concentration of the pulp which in turn is proportional to the oxygen partial pressure in the bubble 1 2 3. Improving the rate of mass transfer of oxygen increases the dissolved oxygen concentration of the slurry and therefore improves the rate of the reaction.The rate of mass transfer from a bubble to its surrounding solution increases with decreasing bubble size and increasing gas bubble residence time which in turn increases with decreasing bubble size. The generation and dispersion of small bubbles is thus critical to achieving high rates of mass transfer. Different configurations and devices used to inject gas have different effects on the bubble size and the residence time, influencing the overall rate of mass transfer. Therefore better mass transfer can be achieved by adopting a more efficient method.The methods tested in this report are the four lance configuration (wall spargers), the inverted cone and a new device, designated HCD. The wall spargers and the inverted cone are used widely in the industry today."

Jan 1, 1994

The Daly-Judge Tunnel, begun in 1887 to drain mine workings, is now a source of potable water for the Municipality of Park City. The water is exceptionally clean; however, when roof falls occur, suspended solids levels become too high and water from the tunnel cannot be used in the treatment plant. In 2001, the tunnel was inspected and rehabilitated to ensure that the water supply for the 2002 Winter Olympic Games would be uninterrupted. Twenty-five timber tunnel sets were removed, and 86 steel sets were installed. Timber lagging was installed or replaced over about 230 m (750 ft) of tunnel length.

Jan 1, 2006

By H. A. Baxter

THE Eustis concentrator is located about nine miles southwest of Sherbrooke, on the main line of the Quebec Central railway. The concentrator is served by a side track parallel to the main line, and all supplies for both the mine and mill are delivered at the mill yards. The concentrator treats 250 tons of copper-iron ore daily by preferential flotation, whereby, first, the copper sulphides are floated and the iron pyrite is depressed, and, second, the iron pyrite is reactivated and floated, resulting in an iron pyrite concentrate and tailing, the latter going to waste. During 1934, 71,709 tons of ore were treated, averaging 3.712 per cent copper and 32.1 percent iron, with a small amount of silver and a trace of gold. The recovery was 93.77 percent of the copper, and 70.43 percent of the iron as iron concentrate. The copper concentrate produced averaged 25.623 percent copper and the iron-pyrite concentrate averaged 42.13 percent iron and 49.173 percent sulphur. HISTORY The first mill at the Eustis mine was built in 1904 (1). For a few years previous to this rime, some jigs had been operated to concentrate the fines from the mine, the coarse ore being hand-sorted. Both the fines and sorted lump ore were shipped to acid plants. The building of the mill was based on test work carried out by Professor Robert H. Richards at the Massachusetts Institute of Technology. The method of concentration consisted in careful classification in a Richards classifier, which made six different sized products. These products went to Wilfley tables, where a concentrate, middling, and tailing were made. The middling was returned to the rolls. Crushing was done by a jaw crusher and two sets of rolls, resulting in a screen size of about five-mesh.

Jan 1, 1936

By J R. O Walli

Large production shafts can be successfully sunk through the ubiquitous Blairmore formation of southern Saskatchewan by employing the freezing process and by the installation of a cast iron tubbing lining. Although the freezing technique for shaft sinking and the use of cast iron tubbing to preserve the shaft are new to the North American continent, these procedures have been employed in Europe for the past eighty years. More than 200 shafts, covering a wide variety of ground conditions, have been sunk by the freezing process, and most of these have been lined with cast iron tubbing. The No. 1 shaft of International Minerals and Chemical Corporation, near Esterhazy, Saskatchewan, comprises the first major example in Canada of the employment of European methods to overcome extremely difficult ground conditions. The Blairmore formation was solidified by the deep freezing process, employing a lithium chloride solution as the refrigerant, with input temperatures ranging to -55°F

Jan 1, 1964

By A. Moyano

The development of the traditional converting process performed in a PeirceSmith or Hoboken converter is limited by the investment magnitude associated to the fulfillment of the environmental regulations. Thus, the continuous converting process rather than a conceptual process alternative is becoming a necessity for a smelter facing limited converting capacity and/or lacking of fulfillment of the environmental regulation with its maximum converting capacity. The objective of this paper is to present the progress of the Codelco continuous converting process evaluated at pilot-scale level when converting solid mattes or white metal into blister copper. These tests allowed for gathering of relevant data to be considered for a new stage of evaluating the Codelco continuous converting at industrial-scale test. The pilot-scale tests were done in a Teniente Converter pilot scale unit at the Codelco Norte Smelter. The results of processing solid copper mattes (65-75% Cu) and producing low sulfur content blister copper with production of a constant S02 gas concentration, and the production of liquid slag with low copper solubility was achieved and is discussed in the present paper.

Jan 1, 2007

By H. Arima

The Akita Zinc Company is the only refinery which produces hematite from the iron content in the zinc leach residue. The Akita Hematite Process consists of five stages, which are SO2 pressure leaching, the first neutralization stage, the de-arsenic process, the second neutralization stage and pressure hematite precipitation. In order to strengthen its cost competitiveness and stabilize its operation, the Akita Hematite Process has been modified continuously. Most recently, two process modifications were carried out. The first was an improved ability to maintain a lower arsenic concentration in the de-arsenic process, and the second was an increased throughput in the hematite precipitation autoclave. The details of these recent changes in the Akita Hematite Process are presented in this paper.

Jan 1, 2006

By C. -G. Berg, J. T. Tuominen

Since the beginning of the 20th century, energy efficiency in copper smelting has been improved by a factor of 30 as a result of adopting autogenous smelting processes with more and more efficient waste heat recovery systems, increasing use of oxygen enrichment and countless smaller improvements. Nevertheless, energy in the form of electricity and fuels continues to be the biggest contributor to smelter operating cost. Metallurgists around the world are under constant pressure to find ways to save those precious megajoules wherever they can. One area that is often neglected is the removal of water contained in concentrates. Copper flotation concentrates, as delivered to a smelter, typically contain some 8–12% moisture. This moisture must be removed and the only way to do this is by evaporation, which consumes a lot of energy. Several studies have shown that the most efficient way of removing this moisture is to use a steam- heated indirect dryer—the least efficient way being the feeding of wet concentrate directly into a smelting furnace. Even in the most efficient smelters that employ modern steam drying, the energy needed to remove the moisture from the concentrates constitutes over 15% of the total energy consumption of a smelter – acid plant complex. The major steps that have been taken in the past to lower the energy consumption of moisture removal are the use of drying in general and the adoption of steam drying. The energy efficiency of concentrate drying has been improved by 25% over the last 20 years. The latest giant leap in this area, the Kumera Heat Recovery Dryer, is the result of Kumera’s long-term development in improving the efficiency of concentrate drying. The Heat Recovery Dryer is a novel application of steam drying that uses the waste heat from dryer exhaust gas for drying concentrates, thus, cutting the energy consumption by a further 30%. This paper discusses energy consumption in copper smelting in general and analyzes the energy consumption of concentrate drying in detail. Different dryer types are compared especially from the perspectives of energy consumption and environmental emissions. Applicability of different energy sources for drying is evaluated and discussed. The principle of the Kumera Heat Recovery Dryer is presented along with results from extensive continuous pilot plant tests. Potential applications and the feasibility of Kumera Heat Recovery Drying technology are discussed.

Jan 1, 2019

By Hilden. M.

"As the Cadia mill was the first 40ft diameter SAG mill, commissioned in 1998, its performance, liner and discharge design attracted considerable international attention. Twelve years on, the liner design and the control philosophy are being readdressed to further improve the mill’s performance. A comprehensive series of 3D liner scans, over life of the liner, have been used to calibrate liner mass loss and progressive changes in the liner profile. This data is being used to provide true charge mass and mill filling, plus progressive trajectory profiles over life of liner. This information, along with measures of mill performance over liner life, is being used to select the optimal operating conditions as the liner wears, and hopes to inform future liner design. INTRODUCTIONSince the Cadia mill was the first 40ft diameter SAG mill, its performance, liner and discharge design has attracted considerable international attention, as reported in previous SAG conferences. The mill experienced particular challenges with regard to pebble and slurry discharge, which necessitated a discharge redesign, incorporating a considerably greater pebble port open area and curved pulp lifters (Hart, Valery, Clements, Reed, Song & Dunne, 2001). Packing between lifter bars on the shell liner was found to dramatically reduce mill throughput over the first half of the liner life. In response, the liners were redesigned to a 2/3 spacing so as to open up the space between lifters. Due to ongoing high liner wear issues, the liner was redesigned based on the discrete element modelling (DEM) of Conveyor Dynamics conducted by Nordell and Potapov (2001). This aimed to maintain mill throughput with new liners and provide an extended liner life. This design was kept proprietary for many years, so has not been open to review."

Jan 1, 2012

By A. J. Smethurst, S. B. Hearn, S. Boskovic

"The problem of crud in solvent extraction is well known and can be a major handicap and operational issue. Colloidal silica can cause a number of problems including interfering with flocculation, initiating crud formation in solvent extraction (SX), decreasing SX extraction kinetics and increasing SX phase disengagement times. Flocculation can be utilized to remove some of the troublesome particulates but colloidal silica does not flocculate well and presents a different problem requiring innovative chemistry to solve. Coagulants can assist by facilitating the removal of this colloidal silica by promoting the agglomeration of the particles to a size which can be more readily settled or flocculated in solid/liquid separations. This is achieved when the coagulants bind to the surfaces, displacing water and destabilizing the colloids, whereupon they bind to each other which facilitate their amenability to conventional flocculation.INTRODUCTIONSilicate minerals are abundant in the upper layers of the Earth’s crust, and there are few mineral deposits without significant levels of gangue silicates. Silicate minerals include the pure silicas, such as quartz and other silicate containing minerals such as clays, chlorites, feldspars, as well a vast number of less common silicates.During the acid leaching of ores, two types of fine silica particles are released in solution from the dissolution of the host mineral. The first consists of partly depleted silicates, and the second is colloidal silica, which forms in solution. It is this second type which has the potential to cause crud formation as well as poor solution clarities, slow filter rates and excessive flocculant usage (Figure1)."

Jan 1, 2016

By Mengsu Hu, Yuan Wang, Jonny Rutqvist

Material interfaces and typical boundary conditions are boundaries influencing the existence, uniqueness and stability of numerical solutions of water flow in heterogeneous media. The Numerical Manifold Method (NMM) with a two-cover-meshing system is an ideal method to handle boundaries, considering its flexibility with no need to adjust mathematical nodes onto boundaries, the meshing efficiency, and its integration precision. In this study, we derive and compare two new approaches for boundary constraints, i.e., a discontinuous approach with Lagrange multiplier and a continuous approach with jump function in the frame of NMM. In the discontinuous Lagrange multiplier method (LMM), Dirichlet boundaries or the material interfaces are regarded as discontinuities which are linked by Lagrange multipliers. In the continuous Jump function method (JFM), the material interfaces are regarded as inner interfaces, where the refraction law is realized by constructing jump terms with discontinuity of hydraulic gradient in its normal direction. Both the continuous and discontinuous approaches make full use of the aforementioned advantages of NMM and are established based on a clear physical meaning of water flow by our energy-work seepage model. The newly derived boundary-constraint approaches were coded into an NMM water flow model and tested for precision and efficiency on different simulation examples. We first tested both LMM and JFM for an idealized heterogeneous model, comparing the numerical results with analytical solutions. Then we tested both approaches with a heterogeneous model and compared the results of hydraulic head and specific discharge. We proved that both approaches are very suitable for material boundaries considering the accurate realization of the boundary constraints and the flexibility with no need for mesh-conforming.

Jan 1, 2015

By T. Haubold, K. Ortner, T. Jung, D. Roth-Fagaraseanu, C. Mattern

Application of integrally bladed disks (blisks) is of increasing interest in compressors of aero engines. Blisks are preferred due to their potential for size and weight reduction, for increased performance and for reduced manufacturing costs compared to conventionally bladed disks. Erosion of the blisk aerofoils in service reduces engine performance, and can result in short shop visit cycles. This significantly increases the life cycle cost of these components, particular when considering that eroded aerofoils can't be exchanged easily for blisks during refurbishment. Shop visit cycle times can be extended and maintenance costs can be reduced through the application of an effective protective coating. The ongoing development of an erosion resistant coating and deposition process suitable for coating complex blisk geometries is described here. The coating is a multilayered W /TiB2 system exhibiting superior erosion resistance compared to known single- and other multilayer concepts. A modified sputter process is used to enable coating even of blisk geometries with shadowed surface to competitive recurring cost.

Jan 1, 2006

By C. A. Young, H-H. Huang, L. G. Twidwell

Solid particles, especially oxides/hydroxides, develop an electrical charge on their surface when submerged in aqueous solution. Parks was able to relate PZC (point of zero charge) of an oxide to its minimum solubility and isoelectric point. Dzombak has compiled an extensive database for adsorption reactions on ferrihydrite surfaces using the double layer theory. The equilibrium calculational program, STABCAL has been used to extend the considerations of Parks and Stumm. The PZC for many hydroxides, complex oxides, and non-oxides have been investigated and the results are reported in the literature. Removal of arsenic and metals by adsorption on ferrihydrite as the substrate has been computed using ST ABCAL and the computational results are compared to experimental data. Absorbents other than ferrihydrite such as aluminum hydroxide are also discussed.

Jan 1, 2005