Search Documents

By S. Joshi, E. Asselin

An electrochemical quartz crystal microbalance (EQCM) was used to study the leaching of pure gold in deaerated 1 M Na2S solution. Multiple cyclic voltammograms were measured between -0.76 and 1.242 V (SHE) at 20 mV/sec and 2 mV/sec and the frequency shift of the quartz crystal was simultaneously measured. Both the forward and reverse scans showed oxidation occurred between -0.40 to 0.20V. The frequency shift increased during both the forward and reverse scans in the potential range of -0.40 to -0.06 V indicating electrode mass decreased. Since at -0.40 to 0.20 V oxidation peaks were also observed, part of the oxidation was due to oxidation of gold. Eh-pH diagrams were constructed and showed soluble Au(I)-S(IV) species formed between -0.30 and 0.10 V (SHE). Atomic absorption spectroscopy of the test solutions and the mass change recorded by EQCM both showed about 0.015 mg of gold leached. Since the majority of the frequency shift increase corresponding to gold oxidation occurred at -0.40 to -0.06 V during multiple cyclic voltammogram measurement, the total leaching of gold could be approximated to occur at this potential interval to give a leaching rate of ca. 6.4x10-5 mg/s-cm2.

Jan 1, 2011

By F. Rashchi, N. Naseri Joda

Recycling of electronic wastes is an important subject both from an environmental point of view and also the recovery of valuable materials. In this research, PC board scraps were leached to recover Cu, Ag, Au and Pd. Due to the high cost of the shredding process and to avoid secondary pollution from odors and dusts, board scraps were cut into 5X5 cm2 pieces. To determine the most effective leachant, aqua regia, nitric acid, hydrochloric acid, ammonium persulfate and potassium persulfate were tested. The effect of the leaching parameters, the leachant concentration, temperature, leaching time and liquid to solid ratio were studied and optimized using response surface methodology.

Jan 1, 2011

By Tatsuya Oki

Tantalum capacitors can be found mounted on printed circuit boards of domestic appliances such as personal computers. These capacitors contain a considerable quantity of expensive metal tantalum and can be detached and liberated from printed circuit boards by impact breakers. In this study, the size and density distribution of the liberated electronic devices were investigated. Then, tantalum capacitors were recovered from other electronic devices using size separation and pneumatic gravity concentration methods. More than 70% of Newton's separation efficiency was obtained for tantalum capacitors. High Newton's separation efficiency could be also obtained for other types of electronic devices such as chip resistors.

Jan 1, 2011

By Solar D. Andrés

Several large open pit mines are facing the challenge to design and plan an underground transition to sustain the long term future of their operations. The desired underground method is Block Cave since its natural high productivity and low operating cost that could compete against the open pit cost to mine the final open pit pushbacks. It has been found at several operations where this transition is taking place that the pit limit at which transition is performed is rather deep. This aims to think that perhaps several transition projects have started late in the life of an operation producing an over stress in the transition project and reducing the flexibility in the design of the overall infrastructure and a substantial lost in the complete project NPV. Traditionally the approach to plan open pit underground transition consists of sequentially deciding the final pit using a Lerchs and Grossman type of optimization to find the overall maximum pit shell and then running block cave simulations to find the best footprint for the underground option. The research summarized in this paper is related to the development of an integer linear programming model that aims to compute simultaneously the maximum NPV of the combined option final limit open pit and block cave underground footprint. The model has been tested using two large block models representing two of the current operations in the process of transiting from open pit to underground operations. Finally, the integrated open pit underground transition model is going to be compared to the traditional sequential approach in order to define which method achieves the best NPV. The paper illustrates both case studies in depth.

Oct 1, 2009

By E. S. Moore

DEEP oxidation and-secondary enrichment of ore deposits, although so important in many parts of the world, are comparatively rare in the Canadian shield. Intensive glaciation during the Pleistocene epoch accounts for their rarity. Glaciation has cost Canada much in the destruction of not only enriched ore deposits, but placers that must have been developed near our numerous gold deposits during the long period of weathering that pre-ceded the Pleistocene. There seems to be a very common misconception regarding the average depth of rock that has been removed from the shield by glaciers. These bodies of ice are usually given credit for the removal of the greater portion of the thousands of feet of rock that we know has been eroded from this large area since Precambrian time. As a matter of fact, the average thickness of solid rock removed can be measured in tens rather than even hundreds of feet, although very deep erosion has resulted in some sections where the glacial ice has been constricted in depressions, such as deep valleys and lake basins. On the other hand, there are few areas within the shield where the glaciers have not disturbed practically all of the mantle rock and some feet of the underlying bed-rock. The chances of finding deeply oxidized cappings and enriched ore deposits are therefore comparatively few and these have been found chiefly where favourable structural and topographic conditions for their formation and preservation have existed. Faulting has been responsible for several of these deposits, and easily decomposed rocks, such as. sulphides and carbonates, have been very important factors. Topographic features, such as high and resistant hills, favourably situated with respect to the ore deposits have, in a few cases, played a part in providing protection from glacial erosion and in furnishing head for the descent of surface waters. At least four cases of oxidation to depths quite abnormal in the Canadian shield have so far been found in Ontario. These are the Helen and Josephine iron mines in the Michipicoten district, the Keeley silver mine in South Lor-rain, and the Ross gold mine in Hislop township, Cochrane district. A deeply oxidized zinc deposit of unusual interest occurs in the Precambrian rocks in New York State, not far from the Canadian border, and there arc the well-known iron deposits in the Lake Superior region of the United States.

Jan 1, 1938

By F. Bosché

Previous research has shown that ?Scan-vs-BIM? systems are powerful to provide valuable information for tracking structural works (progress, quality, safety). However, the transferability of this capability to other construction areas such as MEP works has not been assessed so far. Comparatively, the construction of MEP systems, in particular pipes and ducts, tends to be more flexible with respect to the positioning of individual components, so that Scan-vs-BIM systems could be defeated when tracking MEP installation works. This paper presents recent results on the feasibility and performance of using a Scan-vs- BIM system to track MEP works. The approach followed is presented and then tested with two real-life challenging case studies were conducted simultaneously but totally independently in Canada and Italy. The results show that, as expected, pipes and ducts tend to be more loosely positioned than structural elements leading to a poorer performance of the Scan-vs-BIM system. Nonetheless, it appears that the system works well to assess the level of conformance of site installation works, providing valuable information for estimating emerging performance metrics like ?percent built as-designed?. In addition, the proposed system could also be useful to accelerate and thus reduce the cost of delivering as-built BIM models for in the case of new builds.

Aug 1, 2013

By E. J. Burrough

MR. J. J. McIntyre (International Coal & Coke Company, Ltd., and McGi1livray Creek Coal & Coke Company, Ltd., Coleman, Alta): Mr. Burrough's excellent paper, Metallurgical Coals of the Crowsnest Area, seems especially timely now, when the need for developing iron industries in the west, as well as in the east, is receiving so much attention. His -thorough review of the 'coking' industry is an especially valuable contribution, along with which the following brief remarks on coking in the Crowsnest Pass area of British Columbia and Alberta may be in order. When the Crowsnest Pass line of the Canadian Pacific railway was built there were great expectations for the non-ferrous metal industry; quite a number of smelter's were al-ready in operation in British Columbia and the northwestern United States, and further expansion was confidently expected. The suitability of the medium-volatile coking coals of the Pass for making metallurgical coke had been recognized from the time the fields were first explored. By the time the mines were fairly well developed there was already a market to war-rant the building of coking plants, and a common belief that expansion of the market would require a large coking industry. The first coke production was from plants built by the Crowsnest Pass Coal Company, Ltd., at Fernie, B.C. in 1903, and the International Coal and Coke Company, Ltd., at Coleman, Alberta. These plants were followed by others built by the Crowsnest Pass Coal Company, at Michel, B.C., by West Canadian Collieries, Ltd., at Lille, Alberta, and by Leitch Collieries, Ltd., at Passburg Alberta, and by a plant at Hosmer, B.C.

Jan 1, 1951

By Z. Trojanová

Mg micropowders generated by gas atomisation of a magnesium melt with argon were mixed and ball milled with ceramic nanoparticles prepared by laser-induced gas phase reaction. The materials were then hot extruded. Specimens were deformed in tensile as well as compression tests at temperatures between 20 and 300 °C at a constant initial strain rate. The flow stress is significantly influenced by the test temperature. The yield stress decreases with temperature. This decrease and the flat character of the stressstrain curves at elevated temperatures indicate possible contributions of softening processes. The materials studied exhibit high-damping characteristics. The results are analysed and possible mechanisms are discussed.

Jan 1, 2006

By S. Abu-Samra

By virtue of its complex nature, the construction industry comprises a wide spectrum of interrelated variables and factors. This multifaceted character of the construction industry puts the use of engineering modeling tools and techniques on top of project management necessities. This research introduces a macro-level earthmoving management system using Genetic Algorithms (GAs) to reach the optimum allocation of earthmoving equipment. The Earthmoving Equipment Management System (EEMS) functions through four integrated modules: (1) A Central Database containing information about projects and available equipment; (2) An Equipment per Segment Selection module that calculates the cut and fill quantities, plots the Mass Haul Diagrams, and selects the equipment types to be used for each segment; (3) An Equipment Pool module which determines the production and cost for each available equipment, based upon the project site conditions; and (4) An Optimization Engine equipped with a GA optimization solver. This engine formulates the optimum earthmoving cost for all projects, by changing the number of allocated equipment. The Optimization Engine takes into account the number of available equipment and calculates the weekly equipment allocation. The EEMS model was implemented on an earthmoving company conducting five different projects on hand. The model proved to be an effective tool in providing decision makers with optimum equipment utilization on a multi-project scale to minimize the earthmoving cost. The results were then compared with the company?s existing micro-level management system, demonstrating better performance on the level of savings, amounting to 13% of total earthmoving cost.

Aug 1, 2013

By Michael S. Moats, Prashant Bagri

"In recent years with increasing concerns about energy consumption in hydrometallurgical processing, there is an ongoing attempt to use Catalytic Titanium Anodes (CTAs) for copper electrowinning. For this work, anodes with IrO2 - Ta2O5 coatings were prepared in the laboratory with the same total coating loading but varying the number of layers by changing the speed of withdrawal in dip coating. A second set of CTAs were fabricated on niobium, Ti Grade 1, Ti Grade 7 and Ti Grade 36 metal substrates. All the anodes prepared in the laboratory were characterized using standard electrochemical techniques and subjected to accelerated life testing. It was found that the coating would not adhere to the niobium substrate, the grade of titanium had a minimal to no effect on the life of the anode, and it is observed that as the coating speed slows, there is an increase in the electrochemically active surface area of the coating which seems to directly contribute to an increase in the Tafel slope of the anodes. There was inconclusive evidence on the effect of coating speed on anode lifetime.INTRODUCTIONLarge scale hydrometallurgical extraction of copper has become widely practiced over the last 40+ years. The hydrometallurgical route entails leaching, solvent extraction and electrowinning. With the increasing desire to process refractory sulphides like enargite and chalcopyrite through the hydrometallurgical route, use of hydro-processing of copper is expected to remain high.In conventional electrowinning, copper is deposited on the cathode and an inert anode is used for oxygen evolution. Presently, the most common anode material is rolled lead-calcium-tin and the cathode is 316L stainless steel (Robinson et al., 2013). This lead alloy is fairly inexpensive and is robust, providing lifetimes typically of 4+ years. The main drawbacks of lead alloys are their relatively high oxygen evolution overpotential, the need for cobalt in the electrolyte to reduce their corrosion, the contamination of cathode product by lead, and the generation of harzardous by-products (Hiskey, 1999)."

Jan 1, 2016

By S. R. L. Harding

"Introduction0N MAY 2th, 1953, Socony Seaboard Pembina No. 1 well, located 70 miles west-southwest of Edmonton, was completed as a producer of high-gravity oil from the Cretaceous Cardinm sand. This event is possibly the most significant in the development of the oil industry in Western Canada since the Devonian discovery at Leduc in 1947. The result of the Pembina discovery and the follow-up drilling has been a tremendous increase in interest in the Cardium formation.Descriptions of the Cardium formation, as it occurs in the 'Central Foothills' and in the 'Southern British Columbia Foothills' have been presented by R. E. Folinsbee (9)-and C. R. Stelck (21), respectively. The purpose of this paper is to discuss the more regional aspects of the subject.The name Cardium was first used .as a stratigraphic term in 1863. Dr. James Hector ( l2), geologist attached to Captain John Palliser's exploratory expedition, gave the name 'Cardium to the whole section of marine Cretaceous beds exposed along the Bow river west of Calgary."

Jan 1, 1955

By Subagyo, Geoffrey Brooks, Ken Coley

The generation of droplets and their subsequent reaction in the emulsion is critical to the overall kinetics of oxygen steelmaking. High temperature experiments have been performed at McMaster University to study this behavior. The results from this work and other previous studies has formed the basis of a number of physical and chemical models that attempt to describe the critical aspects of droplet behavior in Oxygen Steelmaking. These models include semi-empirical models for predicting droplet generation rate, droplet size distribution and droplet residence time as a function of blowing parameters.

Jan 1, 2004

By J. Shahabpour

"Abstract - Breccias with angular and rounded clasts of a late-mineralization, ""barren"" hornblende porphyry dike set within a comminuted matrix consisting of rock fragments and quartz, cemented by quartz and K-feldspar of hydrothermal origin is observed in diamond drill cores from the Sar Cheshmeh porphyry copper deposit. Studies of age relationship between vein types, phyllic-altered clasts and the breccia groundmass suggest that the brecciation is a late event. The breccia clasts record evidence of hydrothermal reaction between the clasts and fluids responsible for the brecciation.Formation of bornite, in the breccia clasts of the originally barren hornblende porphyry dike, and in the breccia matrix, along with the scarcity of bornite in the Sar Cheshmeh deposit itself suggest involvement of fluids which are later and of different composition from the fluids responsible for the known mineralization at Sar Cheshmeh. These later fluids may be related to a later plutonic event and suggest the possibility of a later, and concealed deposit."

Jan 1, 1994

By B. A. Monkman

"IntroductionONE OF :THE most effective methods by which the construction industry is combatting mounting building costs is by making increased use of lightweight materials, thus reducing the dead load to be carried •by structures. This applies to non-metallic materials as well as to metallic ones, and particular attention has been given to developing lightweight aggregates for use in concrete.The use of lightweight aggregates is not new and, in fact, dates back to the Roman Empire, when pumice was used in the walls and domes of the Roman buildings. More recently, and up to a decade or so ago, the demand for these aggregates was met from deposits of volcanic cinders, pumice, scoria, etc., and from the by-products of blast furnaces and coal burning boilers. However, these sources of supply are no longer sufficient to meet the demand, for transportation costs pretty well restrict the use of the natural lightweight aggregates to the western cordillera regions where the deposits of these materials occur, and the use of expanded slag aggregates to the areas neighbouring the plants where slags are produced. As for cinders, the supply has been greatly reduced by the conversion of industry to fuel oil, natural gas, and powdered coal, and the large stockpiles which existed previously have been pretty well exhausted.Industry's approach to the problem of a decreasing supply, in the face of an increasing demand, has been characteristically direct. The solution has been to construct plants whose sole .purpose is to produce economically an acceptable light-weight aggregate from materials close at hand."

Jan 1, 1955

By Gorrell. H. A.

Subsurface water data can be very valuable in .petroleum exploration and research. For the discussion of problems related to subsurface waters uniform nomenclature and classifications are required. The term 'connate water' has frequently been incorrectly used. It should .only be used in its original sense in which it is analagous to 'fossil water'. Classifications .based on origin and on sodium-chloride content are proposed. Present and possible uses of formation water analyses are briefly discussed. Since the potential uses of formation water data are not fully understood, complete analyses of selected samples should be made to insure against future requirements. The subsurface waters of Alberta show considerable regional variation in amount and proportion of dissolved salts.

Jan 1, 1958

By J. D. Bateman

Introduction The lifting of restrictions on the development of radioactive mineral deposits by private individuals has re-opened the search for uranium in Canada to a large body of professionally trained prospectors. The entry of private capital and experienced prospecting techniques into the search for radioactive minerals has been enormously stimulated by the atomic developments of the past several years; and we can now look forward to the discovery of new productive sources of uranium. The rate of new discoveries will, how ?ever, depend on the effectiveness of the methods used. The large number of new pitchblende occurrences reported within the past several months is largely a measure of the energy with which the portable Geiger-Müller counter has been applied in the field. The counter is simply a 'radio' receiver tuned to one of the products of spontaneous atomic disintegration that is characteristic of all radioactive materials. Its effective use depends largely on how it is applied under the various geological and topographical conditions that ma y be encountered, and also on an understanding of its limitations. Extensive geological information relating to the occurrence of radioactive minerals in Canada has been accumulated during the past several years, and it is now possible to define in a general way many of the geological formations in which pitchblende and related minerals are likely to occur. Furthermore, prospecting can be localized in those parts of the favourable formations that offer the greater promise of containing commercial deposits. In this selection, the Geiger counter is the most useful tool available to the prospector for the actual detection of radioactive materials. As an example, an area of two square miles in the Northwest Territories, within which about a dozen pitchblende occurrences had been found over a several year period by conventional prospecting methods, yielded more than forty-five additional discoveries by application of the Geiger counter. Yet earlier attempts at prospecting this area with the counter had failed, due largely to faulty instruments and lack of experience in field application. The limitations of the counter are very considerable; but, when they are recognized, there is no more useful tool for the discovery of radioactive ores. It was not until 1944 that a practicable portable counter was developed, and then only by co-operation in the field by geologists and physicists. Officers of the Geological Survey of Canada working with physicists of the National Research Council brought about the development of the modern counter.

Jan 1, 1949

By M. Barati

A collaborative research between University of Toronto and Hatch was conducted to understand and optimize the process conditions pertaining to a novel steelmaking technology. In this technology, known as CRISP, direct reduced iron is continuously melted and refined in a stationary electric arc furnace. The major challenge against continuous operation of the electric furnace was identified to be minimizing the corrosion of the refractory in order to achieve uninterrupted operation for a minimum of one year. Theoretical analysis and bench scale experiments together with two pilot runs resulted in defining an operating window for slag chemistry that would minimize chemical attack to the refractory while satisfying the oxidizing conditions required for sufficient decarburization. An analysis of the process in terms of energy consumption and emission of greenhouse gases revealed that it is superior to the current batch DRI-based steelmaking technologies.

Jan 1, 2011

By J. E. Gill

Discovered in 1952, the deposits have been explored by diamond drilling on and near a group of islands in lake Nipissing and from under-ground workings. The ore mineral is a uranian pyrochlore. It occurs in breccia zones in association with calcite, apatite, a?cmite, feldsiiars, biotite, magnetite, sulphides, and fluorite in varying amounts. The pyrochlore concentrations occur in a steeply-dipping gneiss series with some crystalline limestone. Trends indicate a ring structure 114 miles in diameter. The main ore zone shows evidence of repeated brecciation and a succession of replacements .giving rise to a complex of rock types. Pegmatite and lamprophyre dykes cut the ore as do calcite-fluorite veins and later faults with small displacements. Columbium and uranium occur al-most exclusively in pyrochlore, but the proportions vary. There is no tantalum and only small amounts of titanium.

Jan 1, 1957

By Kaiwen Xia, Bibhu Mohanty, Per Svedensten, Sheng Huang

"The mechanics of crushing and grinding operations in mining and excavation processes has been investigated in a laboratory simulation study. It employs a multi-particle bedded rock target, which is subjected to multiple impacts. The impact set-up consists of a Hopkinson pressure bar and a Piston-holder system. The apparatus, employing a 38 mm diameter pressure bar, was used to apply varying but calibrated dynamic loading force on the rock particles. The energy consumed by the sample during fragmentation was determined by considering the energy carried by the incident wave and the reflected wave. The Pistonholder system is used to hold rock samples and to recycle fragments after each test for particle size analysis, for single as well as multiple impacts. The feed size selected was in the range of 9.5 to 12.7 mm for all rock samples, and the impact velocity was set at 14 m/s. Two strong granitic rocks and a relatively weak limestone were the target rocks. The resulting particle size distribution after each set of impacts, ranging from single to 10 consecutive impacts, were analyzed, and various size distribution functions (i.e. Rosin- Rammler, Swebrec, Grady and Gilvarry functions) were fitted to compare their suitability in predicting the fragment size distribution for each rock type. INTRODUCTIONCrushers are widely used in the mining industry all over the world. Understanding fragmentation behaviour of rock under crushing process is fundamental to improved productivity and efficiency in mining operations. This is particularly so as all subsequent size reduction processes such as crushing and grinding are far more energy intensive than the initial blasting process employed in breaking of in situ rock. A considerable body of experimental studies exists on the behaviour of rock crushers for specific rock types in order to aid in the design of various types of crushers. However, these studies are mainly site specific, that is, the results are largely empirical, and the fundamentals of fracture process that lead to size reduction have not been dealt with adequately. Most such studies have attempted to link the input parameters, such as feed size and crusher parameters, with output particle size, and global energy expended in the process. However the physical mechanism of crushing process is still not well understood. First of all, the energy consumed by the rock sample is hard to calculate during standard crushing or grinding tests; secondly, multi-particle test is hard to perform in the laboratory due to irregular shape of the subject rock sample. In This paper, describes a laboratory crushing apparatus for multi-particle rock samples, with sufficient control of the energy expended in the process, with a view to relate creation of new fracture surfaces in the size reduction process."

Jan 1, 2015

By Nader Golchinfar

The V-shaped breakout zones around excavation boundary have been captured by a variety of numerical methods such as FEM and DEM methods and failure criteria such as linear Mohr-Coulomb and non-linear Hoek-Brown failure criteria. Diederichs (2007) used Hoek-Brown parameters in his spalling parameter approach; however, it is convenient to use the Mohr-Coulomb failure criterion in numerical modeling because the material parameters can easily be determined from triaxial tests. It is shown in this study that when peak and residual strength parameters as well as dilation angle are properly defined, the brittle Mohr-Coulomb failure criterion can be used to model depth of failure near underground excavations satisfactorily.

Jun 1, 2012