Search Documents

By Grant D. Nicholas

This paper compares an integrated evaluation approach to decision-making with more traditional sensitivity analysis and Monte Carlo simulation. The primary objective is to highlight the differences in NPV that can arise from using these evaluation methods in a top down and bottom-up approach. Results from three resource scenarios, derived from sampling a "virtual" ore body (reality) on grid spacings of 75m, 50m and 25m, are analyzed and compared.

May 1, 2007

By C. R. Julian

THE large pyrites ore-bodies, the underground mining of which is to be described, are situated at Rio Tinto in the Province of Huelva in Southern Spain. The situation of the different ore-bodies with relation to one another is shown in Figure 1. It will be seen on the plan that the strike of the ore-bodies is approximately east and west. The geology of the district has been very fully described by Dr. D. Williams (1), so that for the purposes of this paper it will be sufficient to give briefly the salient features o each of the two larger ore-bodies which are being mined by underground methods at the present time. (a) San Dionisio.-This ore-body is the largest single deposit in Rio Tinto, having on its upper levels a length of 3,500 ft. On the upper levels the average width is approximately 200ft. but in places on the lower levels there is a width of 900ft. of un broken pyrites. Diamond-drill holes, without running out of ore, show the ore-body to persist to a depth of at least 1,600 ft. The ore-body in the upper part lies between slate and porphyry walls, but in depth is enclosed in porphyry walls. (b) South Lode.-Faulting is considered to be responsible for the break in the solid ore between South Lode and San Dionisio. On the upper levels, the South Lode ore-body has an unbroken length of 4,000 ft. The massive pyrites has a maximum width of 300ft. and an average of about 100 ft. Ore has been proved to a depth of 1,000 ft., at which depth the ore-body is much reduced both in length and breadth. This ore-body, to the depth at which it has been proved, lies entirely between slate and porphyry walls. The South Lode and the San Dionisio ore-bodies are mined both by open-cast and by underground methods. There is evidence that these mines have been exploited intermittently during the last 3,000 years; but, as is to be expected, no records are available of the tonnage mined prior to the time of purchase by the present company.

Jan 1, 1940

By W. P. Campbell

In the course of the development of the Red Coulee field, northwest of Coutts, Alberta, a considerable amount of information has been gathered by the Department of the Interior regarding the chemical character of waters encountered in the drilling of wells in this area. The writer, in this paper, has undertaken to assemble the available material with the idea of deducing what relations, if any, may exist between the different waters from the same well, and also how these compare with waters encountered in similar horizons in other wells. From no other district, with which the Department of the Interior has had to do, have there been received so many samples of water, and yet not all the waters logged in the drilling reports were sent in for analysis. The information, therefore, herein contained is not as complete as the writer would have desired, but sufficient evidence has been accumulated to indicate some very definite tendencies in the chemical nature of the waters of this field. The drilling of Red Coulee wells has been carried out exclusively by percussive tools. These permit 'dry' drilling, and, consequently, water-sands are recognized when encountered. Had rotary tools been used, information regarding water-sands would have been very meagre, if not entirely lacking, since, in the mudding-off process, water-sands would have been overlooked, with the result that, should water break through into a completed well, its source would not be known and remedial efforts would be greatly handicapped, if not entirely defeated.

Jan 1, 1931

By E. W. Mountjoy

THE Exshaw formation is a thin but very persistent black shale unit generally well exposed along the easterly scarp faces of the fault blocks comprising tl1e front ranges of the Rocky mountains. It is over lain by the Mississippian Banff shales and silty shales and underlain by the massive Palliser Limestone formation of late Devonian age. The Exshaw continues eastward under the plains of Alberta and on into Saskatchewan, with little change until it reaches the surface of the Palaeozoic-Mesozoic unconformity. During the summer of 1953, the writer was working- with a field party under Dr. J. L. Usher in the front ranges of the Alberta Rocky mountains. This party, sent out by the Mobiloil Company, conducted a geological survey of Devonian rocks between the towns of Banff and Jasper. The writer helped to describe and map these Devonian rocks and obtained first-hand information concerning the Exshaw shale and its relationship to the underlying and overlying sediments. Additional information was obtained from reference material and from a number of geologists whom the writer has consulted. Grateful acknowledgment is offered to them, to the Mobiloil Company for releasing field information, and to F. W. Beales and W. P. Hancock who helped edit the original paper for publication. Information from areas north and smith of that studied and from bore holes on the prairies is referred to. Localities mentioned may be found in Figure 1.

Jan 1, 1956

By C. E. Rodgers

WHEN the writer was engaged early last year by Canadian Comstock and its subsidiary, the Metropolitan Electric Company, to act as Consulting Mining Engineer in connection with the layout and equipment of the new ore-dressing laboratories at Laval University, Quebec, the metallurgical laboratory section of the School of Mines building was completely erected, including plastered walls, partitions, etc., and finished concrete floors. At that time, however, no equipment had been ordered, except three Dominion ball-mills and two Bell screening machines. ADVANCED OR CONTINUOUS LABORATORIES The continuous laboratory section of the Department occupies the basement and three floors of the building, with an approximate floor area of 9,000 square feet. Because of limitations imposed by the design of the building (height and arrangement of rooms, strength and design of floors, etc.), modifications of layout from what otherwise seemed most desirable were, of necessity, made. These included: (a) Omission of automatic sampling of the dry ore. (b) Complete elimination of inclined belt-conveyors through floors. (c) Exclusion of bucket elevators for either dry or wet ore transfer. (d) As a substitute for grill-covered drains and floor sumps, drainage from sections or from individual pieces of equipment was piped to a disposal system in the basement. (e) Substitution in several instances of fabricated steel in place of the usual concrete foundations for machinery. (f) Reducing floor cutting and area of such opening to a minimum. Ore storage and chute capacity above the basement level was also minimized to reduce total weight.

Jan 1, 1941

By Robert D. Brown, Robert B. Parsons

"The mining industry may have survived the October 28 federal budget relatively unscathed, but the same certainly cannot be said of the petroleum sector-and many mining men are left wondering if their industry will be the next one to be singled out for special attention, as federal and provincial governments seek additional revenues and pursue nationalistic or provincial policies.Higher taxes, higher prices, a potpourri of ""incentives"", and a -""Canadianization"" policy mark the principal features of the new National Energy Program released by the government along with Finance Minister MacEachen's budget address.This month, Tax Notes examines the federal budget. with appropriate emphasis on the National Energy Program and its possible future implications forthe Canadian resource industries.IntroductionMost of the Canadian mining industry (tar sands miners excepted) heaved a sigh of relief on the evening of October 28, 1980, as Finance Minister MacEachen confounded the prophets in his budget address by not raising personal or corporation taxes and by making only relatively modest changes in the general tax system. Instead, he concentrated on a sweeping new energy policy. Unfortunately for that important sector of Canada's mining industry which is involved in mining the country's vast tar sands reserves, either now or in the future, the National Energy Program that was introduced along with the budget 'has serious implications."

Jan 1, 1981

By R. K. Rajamani

Discrete Element Method simulation of charge motion in ball, SAG and autogenous mills has become a standard for design of mill internals, power draft evaluation, etc. Both two-dimensional and three-dimensional codes are being used. The two-dimensional code dominates the user market since the code completes a simulation in one or two hours. On the other hand, three-dimensional codes have been in the domain of specialists who can handle the complexity of the code and have access to parallel computing hardware. For the first time, this barrier is overcome via computing with graphic processing units (GPU). Commodity graphics cards now allow parallel computation with hundreds of processors. It is shown that the computational time has been reduced by a factor of fifty using GPU computing. Hence, SAG charge simulation results in three dimensions are achievable in a few hours using affordable desktop machines. The GPU computing shown here enables the three dimensional simulation into a manageable daily task for mill designers and researchers. On the technical side, the simulations can be elevated to a higher level of complexity to simulate breakage and transport. First, the speedup factor of fifty is established for the Nvidia GeForce GTX 580 graphics card. Next, four simulation tasks, consisting of AG, SAG and ball mills are reported. The simulation of AG and SAG mills are completed in less than 8 hours. The ball mill simulation with 1.25 million spheres is completed in 27 hours. In the near future, as the graphic card hardware advances the compute time can be halved.

Jan 1, 2012

By Boris Yacksic, R. W. Bruce

"The flotation of a cassiterite ore with oleic acid will recover primary or rougher concentrates assaying over 10 per cent Sn, with a recovery of 80 to 90 per cent. These rougher concentrates cannot be up-graded to a marketable grade by normal reflotation. Experiments were conducted on low-grade tin ores, and a process was developed for up-grading the rougher flotation concentrates by a reverse flotation technique. The process was tested on a number of samples of ore from the Catavi mine in Bolivia. The results of these tests showed that a concentrate assaying 40 to 60 per cent Sn could be readily produced, with a recovery of 60 to 75 per cent of the tin in the ore."

Jan 1, 1967

By A. W. Davis

Sapping and mining have constituted an important part of siege operations ever since powder came into general use in Europe. Before this period, famine was the main weapon in the hands of the besiegers, and the history of the middle ages is replete with accounts of sieges lasting two and three years. With the advent of explosives, a position impregnable to assault might be readily won by mining under, and blowing up, its defences. The natural offensive against this method of attack is to countermine and stop the attackers underground before their objective is reached. Thus developed the art of military mining. The French and British, in the Peninsular war, were adepts at this method of warfare, and the explosion of a mine and the formation of a breach were the usual preludes to the general assault of a position. In the Crimea, at Sebastopol, the British and Russians did a lot of underground fighting, as the old maps of their galleries, now in the museum at Chatham, will testify. In the siege of Port Arthur, in still later times, the Japanese and Russians were hard at it as well.

Jan 1, 1926

By T. Banerjee, Y. Dumais, R. Lemire

"Agnico Eagle LaRonde produces over 300,000 ounces of gold annually, along with silver, zinc and copper by-products. The LaRonde plant consists of a conventional SAG and Ball mill circuit, followed by flotation. Load management is imperative for maintaining stability in grind size and ensuring consistency of the flotation feed. In flotation, the mass pull profiles of the cells and reagent dosage rates need to be managed to maximize recovery, while maintaining product quality. This is achieved by controlling the air, level and reagent addition set-points across the circuit. However, disturbances such as feed size distribution, ore hardness and mineralogy make it challenging to maintain efficient control using traditional control techniques. LaRonde therefore worked to develop a progressive control strategy, targeting stability and optimization. This started with a year-long instrumentation upgrade campaign, focusing on optimizing the performance and reliability of plant-wide instrumentation. The process was then optimized, leveraging AwaRE advanced controllers running in closed loop with PARC modules embedded within the PLC. The installation of 8 PFC cameras in flotation changed the flotation operation from a level and air control based strategy, to one that controls mass pull. This new control philosophy has allowed the plant to effectively manage mill load, improving grind size and providing increased throughput with better flotation performance.INTRODUCTION Background Since 2015, Agnico Eagle LaRonde has been conducting an optimization campaign to maximise the performance of plant assets leveraging instrumentation and control. The grinding and copper flotation circuits were identified as the areas having the greatest opportunities and value proposition for advanced control. A disciplined approach was followed to design and implement a progressive control solution to achieve operational excellence."

Jan 1, 2018

By David Thomas, Charles Harper, Brian Watters

The Star-Waddy Lakes area lies withjn the northeasterly-trending early- to mjd-Proterozoic volcanoseilimentary-pl utoruc belt referred to as the La Range Domllin. In the area investigated the domajn is composed of the Central Metavolcaruc Belt which is bordered by metasedimentary belts of the Crew Lake and MacLean Lake Belts to the northwest and southeast respectively. The boundaries between the Central Metavolcanic Belt and the flanking belts are generally marked by prominent zones of shearing. The volcanosed imentary succession is intruded by a variety of ultramafic to felsic plutons which, on the basis of lithology, field relations and geochronology, can be broadly subdivided into three groups or episodes. These are: a) an 'early' (ea. 1866 Ma), possibly subvolcanic, episode marked by composite intrusions ranging from gabbro-diorite to granite, b) an 'intermediate' (ea. 1854 Ma) plutonic event distinguished by more homogeneous felsic intru ions ; and c) a 'later' (ea. 1835 Ma) event characterized by leucocratic quartz-rich grani te intrusions. The La Range Domain has undergone polyphase deformation with a strongly developed northeast-trending structural grain. Large scale folding is manjfested by large regional sy nforms, arcuate and triangular patterns associated with many of the plutons and by tight to isoclinal folds within the adjacent metasedimentary belts. Inhomogeneous strain characterizes much of the Star-Waddy Lakes area. With strain gradients being typically very steep, zones of high strain consisting of zones of extreme extensional fabrics, discrete shearing, as well as broader zones of cataclasis and structural slicing, are often juxtaposed with areas of relatively minimal deformation . Dilation structures tend to favour these zones of highly contrasting strain. Late, brittle fractures, faults and shear zones are widespread and appear to be particularly important as loci for gold mineralization. Metan1orphic mineral assemblages indicate that upper greenschist to middle amphibolite facies conditions were attained. Geological and geochenucal evidence indicates that the Central Metavolcanic Belt evolved in an island arc environment. Metavolcanic rocks from both the Waddy and Star Lakes areas display similar characteristics on variation diagrams (e.g. AFM and the Jensen cation plot) in that the dominant trend is calc-alkaline with some basic to intermediate types having a mildly tholeiitic character. A few samples from the southern end of Lower Waddy lake display komatiitic to basaltic-komatiitic afl'injties. The relatively immobile minor and trace elements (e.g. Ti , Zr, Nb, Y, Cr) provide reliable characterization of the metavolcanics, particularly of the basalts, which have highly distinctive trace element properties. Geochemical patterns for the basalts are similar to those for modem volcanic arc basalts. Low initial 87Sr/86Sr ratios (0.7017 - 0.7019) are consistent with a subduction-related origin for the volcanics. The major plutons have chemical properties typical of volcanic arc granites and are largely calc-alkaline in character, showing little chemical variation from the volcanics.

Jan 1, 1986

By Morris J. Viljoen, Young. David R.

"Abstract -The zone of economic interest at H.J . Joel Gold Mine is the VS5/Beatrix Composite Reef, a quartz-pebble conglomerate of Archean age. The reef occurs at the base of the Eldorado Formation, Central Rand Group, of the Witwatersrand Supergroup. At !east three stratigraphically distinct conglomerates form this economic zone. In order of deposition these are the Footwall, Beatrix, and the VS5/Beatrix reefs. The Footwall and Beatrix reefs are equated with the Aandenk Formation with transport directions toward the northwest, whereas the VS5/Beatrix Reef is of Eldorado age, with transport directions toward the south. The change in the drainage direction was caused by a major basin-wide tectonic event that occurred prior to the deposition of the Eldorado Formation. The Beatrix Reef was formed in a proximal, braided, fluvial environment by a process of aggrading gravel bars between channelways. The VS5/Beatrix Reef was formed by the desegregation of pre-existing Beatrix Reef with the introduction of new material containing much shale detritus and is seen to have been deposited in a more ·distal, braided, fluvial environment, similar to the Beatrix Reef.The average gold concentrations are different for each conglomerate; the Beatrix at 32.1 ppm Au, the Footwall at 24.4 ppm Au, and the VS5/Beatrix at only 12.4 ppm Au. A sedimentary gold concentrating process related to higher energy braid channels was primarily responsible for these high gold grades. Not only the basal unconformity surface, but also, internal degredation surfaces, were prime sites for concentration. An understanding of the spatial distribution of these differing conglomerates and their braid channels forming the economic reef zone is necessary in predicting ore grades for future mining."

Jan 1, 1994

By Paul Guliov

Coal-bearing Tertiary sediments of the Ravenscrag Formation in southern Saskatchewan host numerous deposits of clinker resulting from in situ coal combustion. Clinker deposits form when sediments of relatively low temperature firing properties overlie coal seams which are undergoing prolonged spontaneous combustion. The resulting fired material is useful for decorative landscaping aggregate, rock gardens, driveways, mud control and others. Predicting the occurrence of clinker deposits requires a knowledge of the spatial distribution of coal seams and the nature ofoverlying sediments. Knowledge ofpaleotopography at the time of coal combustion can assist in locating more highly-fused material which can yield greater block sizes. Coal data bases can be used as a predictive tool by outlining areas where coal is or was at or near surface and therefore may have been susceptible to spontaneous combustion.

Jan 1, 2001

By W. P. Campbell

Foreword At the outset, it should be stated that this paper does not pretend to present a panacea for the ills that 'frozen' wells are heir to, but rather is an attempt to bring to the attention of those whose special concern it is, a little theory and some facts, which have been brought to light recently, in connection with the problem of 'freezing' as it applies to naphtha-producing wells in the Turner Valley field, and to draw some conclusions that follow from the facts discovered. It should also be stated that the investigation is not to be regarded as in any sense complete, but in progress. Doubtless new facts will be brought to light from time to time which may modify present ideas on the subject, but whether favourable or contrary, these will be welcomed, as the purpose of the Department is to secure as complete information as possible of the factors contributing to 'freezing', since this must be the first step to an intelligent attempt to remedy or prevent its occurrence, if such can be done. It is possible, too, that the cause or causes of freezing may not be the same in all cases, but whether this be so or not will have to be determined later as new information comes to hand. Introduction One of the worries which must constantly confront the operators of gas-naphtha producing wells in Turner Valley-although all, fortunately, have not met with it-is the possibility of the occurrence of what is commonly called 'freezing' (going off production).

Jan 1, 1930

By Jiuhua Xu, Shuiku Jia, Weiren Sun

"Abstract -The Jinqingding gold deposit, situated in the east Jiaodong Peninsula of Shandong province, is typical of the pyrite-quartz vein gold deposits in the Muping-Rushan gold belt of China . The gold deposit is controlled by a great NNE fracture zone and is composed of several lenticular orebodies within the fracture zone occurring in the Kunyushan granite massif. The Kunyushan granite massif was formed by the replacement of the Archean Jiaodong group.The main minerals associated with gold are pyrite, chalcopyrite, galena and sphalerite; the gangue minerals are dominated by quartz, sericite, microcline and calcite. The mineralizing event can be divided into four stages: (1) pyrite-quartz; (2) quartz-pyrite; (3) siderite-polymetallic sulfides; and (4) calcite-quartz. Gold occurs mainly as native gold and electrum in stage 1 and stage II. There are some evident differences between pyrite from major stages of gold mineralization and that from minor stages; these include differences in crystal forms, size and composition of fluid inclusions.Wallrock alterations consist of sericitization, silicification, pyritization and potash-feldspar alteration. Five alteration zones can be distinguished from unaltered granite (zone 0) to vein lodes (zone IV). Au and Ag increase rapidly from zone 0 to zone IV, Cu increases continuously, while Pb and Zn increase slowly. R-type geological factor analysis indicates that the Au, Ag, Cu, Pb and Zn bear a close relationship to wallrock alteration."

Jan 1, 1994

During the past 10 years, research work to improve the survey of stope limits after mining supplied useful information, particularly for large open and sub-level stopes, regarding waste dilution caused by differences between final production limits and planned stope limits. However, the efficiency of this information to improve the overall efficiency of the mining process is limited, given that the impacts of inaccurate ore limits leading to dilution (sensu stricto) and ore losses haw not been considered adequately. Geological/sampling information should be optimized in terms of quantity and/or quality for the deposit characteristics and the constraints of the mining method used. As industry practice regarding the definition and recording of dilution is flexible and as ore losses frequently am poorly doc-umented, the use of these terms is reviewed. Simulations were carried out on two typical narrow gold deposits, based on an earlier study at Inco's Thompson mine regarding the impacts of wide to narrow delineation grids using recorded variations of vein geometry. Vertical to sub-vertical deposits of 3 m and 6 m widths mined by long-hole open stopes were considered. Deposits delineated by 7.5 m (25 ft) grids were taken as a base case and the impacts of less accurate limits in conjunction with long hole mining based only on a 15 m (50 ft) delin¬eation grid. The impacts of overestimation (dilution) and underestimation (metal losses) were considered separately, using the average error of +/-0.62 m recorded in the Inco study. The impact of less accurate information was much stronger on the narrower deposit: both dilution and ore losses diminished the net present value of the 3 m wide deposit by 39.27% and 45.41%, respectively, and that of the 6 m wide deposit by 12.84% and 11.55%. As the impacts of ore loss and those of dilution on the net present value am almost identical in these simulations, we could, in practice, assume a 50/50 split between dilution and ore losses in such a case. These results do no take into account the effects of local optimization measures taken at the mine production level (blasthole sampling near stope limits, etc.) The potential impacts of geological and sampling uncertainties in terms of lower NPV justify and require more systematic efforts to ensure that deposit appraisal work and feasibility studies are adequate to optimize company revenue and competitive returns to investors from mine production activities.

Jan 1, 2005

By G. M. Brownell

THE Falcon Lake stock is a small igneous mass, 2.6 square miles in area, which has intruded a belt of older lavas and metamorphosed sediments. It is well exposed and the entire area of its outcrop is taken up with surveyed mining claims, the claim lines forming a grid which makes ideal conditions for a detailed petrographical study of the unusual variations which are found in the composition of this unit (see Figure 1). The study of this mass, which has revealed features of both scientific and economic significance, began in the summer of 1939 when trainees in a Prospectors' Training Camp, a Do-minion-Provincial youth-training project under the writer's supervision, were, detailed to map rock outcrops on various mining claims. Microscopic study of rock specimens taken on a line across this stock were made during the following winter and proved to be of such interest that a special trip was made the following summer for the purpose of gathering more data, the results of which are presented here. Location The stock is close to the southeast corner of the province of Manitoba, about three miles from the Ontario boundary. It lies between Falcon and West Hawk lakes and less than a mile south of the Trans-Canada highway. It is easily accessible by motor car, as a branch road from the highway leads to the Sunbeam Kirkland gold mine, which is within the inner core of the stock. Previous Work This area was the first in the Province to receive attention from prospectors, who entered it from the adjacent Lake of the Woods district during the days of the mining boom in the 1890's. Small occurrences of gold, copper, molybdenum, and tungsten ores were found, but to date there has been no production from the district, except for small shipments of gold ore. The regional geology has been mapped by the Manitoba Department of Mines and Natural Resources, the Falcon Lake stock being shown and recorded as of "varying composition". The more detailed work involved in preparing the accompanying map has necessitated only minor changes in the outline as previously mapped.

Jan 1, 1941

By M. Drozd, M. Somppi, Z. F. Yamak

"Activated carbon is used to recover gold in solution from various gold circuit designs including carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) processes; however, the characteristics and durability of the activated carbon can vary. Handling this medium poses challenges when fine carbon losses occur in the CIP, CIC, and CIL circuit discharge. Additionally, adsorbed gold on carbon fines can be lost to the discharge. The studies in this paper aim to standardize laboratory methods for testing activated carbon qualities specific to the gold industry. The investigation focused on size distribution, platelet content, wet attrition resistance, gold kinetics, and gold loading. The results demonstrate that a 96 h attrition test and a gold loading test form a basis for ranking carbon samples based on expected economic performance of the plant. ¦ KEYWORDS Activated carbon, Carbon attrition, Carbon ball-pan hardness, Carbon evaluation, Carbon fines loss, Carbon turnover RÉSUMÉ Le charbon actif sert à récupérer l’or en solution dans diverses conceptions de circuits de broyage d’or, notamment les procédés de charbon en pulpe (CIP, de l’anglais carbon-in-pulp), de charbon en colonnes (CIC, de l’anglais carbon-in-column) et de lixiviation au carbone, ou charbon au lixiviat (CIL, de l’anglais carbon-in-leach). Toutefois, les caractéristiques et la durabilité du charbon actif varient. La manipulation de ce milieu pose des problèmes dès lors que se produisent des pertes de carbone à grain fin dans la décharge des circuits CIP, CIC et CIL. Par ailleurs, l’or adsorbé sur les fines de charbon peut se perdre durant la décharge. Les études réalisées dans le cadre de cet article visent à normaliser les méthodes de laboratoire pour tester les qualités du charbon actif spécifiques au secteur de l’exploitation aurifère. L’étude portait sur la composition granulométrique, la teneur des plaquettes, la résistance au frottement humide, la cinétique de l’or et l’adsorption de l’or, à savoir la capacité du charbon actif à adsorber l’or sur une période spécifique. Les résultats ont montré qu’un test de frottement de 96 heures et un test d’adsorption de l’or constituaient le fondement d’un classement des échantillons de carbone du point de vue économique en vue de trouver l’échantillon générant le meilleur rendement des usines. ¦ MOTS CLÉS charbon actif, dureté de la batée des billes de carbone, évaluation du carbone, perte de fines de charbon, renouvellement du carbone, résistance au carbone INTRODUCTION The use of activated carbon for gold extraction is among the most common processes in modern gold-milling plants. Although gold losses are inevitable in the milling process, operators often focus on reducing gold loss to tailings. One focus area that is important in gold recovery is optimizing the use of activated carbon and examining potential changes to realize improved economics for carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) processes. Granular activated carbon (Figure 1) is widely used for gold extraction from slurries containing gold-cyanide complexes. This activated carbon—produced from charred coconut shells—is well suited because of its adsorption kinetics, gold-loading capacity, attrition resistance, and ability to be reactivated. The extraction process using activated carbon technology involves adsorbing gold from an aqueous leachate; the gold is dissolved using a cyanide salt and consequently a dicyanoaurate(I) ion (Au(CN)2–) is formed, as noted in equation 1."

Jan 1, 2019

By Rodney A. Cooper

The Mary River iron ore deposits were discovered in the 1960?s. The high quality of the deposits was immediately evident, and drilling programs were successful in defining a resource adequate for supporting a feasibility study. Through a combination of ownership, market and political forces, the deposits were not developed. Having missed the window of opportunity, the project remained dormant for over three decades. Baffinland Iron Mines Corporation, with its 100% ownership of the Mary River deposits, began trading publicly in 2004. Modern exploration and metallurgical test work began in 2004 and has continued in 2005 and 2006, resulting in total expenditures during this period of almost C$60 million. In May 2006, an engineering team lead by Aker Kvaerner E&C, a division of Aker Kvaerner Canada Inc., completed a scoping study based on the first of five identified deposits. Highlights of that study include direct shipping of high quality lump ore to Europe over a 34 year mine life at a production rate of 10 million tonnes per annum, based on an indicated resource of 309 million tonnes at 66.1% Fe and an inferred resource of 28 million tonnes at 65.9% Fe. Capital costs were estimated at C$1.5 billion. Using iron ore prices approximately 36% below that of the 2006 market, a pre-tax internal rate of return of 15% was estimated assuming equity financing. Payback on initial capital was 5.9 years. The pre-tax life-of-mine cash flow was estimated to be C$6.3 billion. As a result of this study, Baffinland initiated a Definitive Feasibility Study, under the management of Aker Kvaerner, which is scheduled for completion in December 2007. This paper touches on the geology of the deposits, the current resource and the outlook for expansion. Project permitting, construction planning, logistical challenges and ocean shipping considerations are discussed, providing a current perspective on the project scale, scope and timeline for commercial production. In addition, an overview of the Company?s bulk sampling program will be provided.

May 1, 2007

By V. A. Preto

The Rexspar uranium deposit is located approximately 5 kilometres south of Birch Island, B.C. Three separate zones of commercial-grade uranium mineralization mineable by open pit have been outlined. Uranium and fluorite-celestite mineralization occur in a trachytic member of alkali-feldspar porphyry, lithic tuff, tuff breccias and pyritic schist conformably interlayered with a succession of strongly deformed greenschists and fragmental rocks that are, in large part at least, of volcanic origin. The age of these strata is not precisely known, but they are considered as part of the possibly Mississippian Eagle Bay Formation. Commercial-grade uranium mineralization is always associated with fluorphlogopite-pyrite replacement of the trachytic unit and is contiguous to, but separate from , a zone of ore-grade fluorite mineralization. In all zones, ore occurs in lenses of variable thickness and lateral extent, which lie parallel to the schistosity of the trachytic rocks and surrounding greenschists. The principal radioactive minerals at Rexspar have been identified by other workers as uraninite, uranothorite, bastnaesite, torbernite and metatorbernite. Considerable amounts of thorium oxide and widespread rare earths have been reported from all three radioactive zones. The geology of the deposit suggests that the trachytic rocks represent a highly differentiated intrusive-extrusive system in which fluorphlogopite, pyrite, fluorite and uranium-bearing minerals were deposited late in the evolution of the system by deuteric, volatile-rich fluids. The considerable amounts of thorium and widespread rare earths associated with the uranium tend to support the thesis that this element is of primary origin rather than secondary.

Jan 1, 1978