Search Documents

By C. M. Offenhauer

Abstract Zirconium markedly affects the formation of graphite in cast iron and may promote the formation of normal flake gaphite, fine flakes of eutectiform graphite, or spheroid nodular graphite, according to the composition of the Iron and the amount of the zirconium addition. Usually, it is employed in the form of a complex addition agent in order to facilitate its introduction and to guide its effect. The reported applications of zirconium as an inoculant for the production of pearlitic high-strength cast iron indicates that it is most effective as a silicon-manganese-zirconium alloy. Added in this form it reduces chill and minimizes zones of ferrite and eutectiform graphite. In low-sulphur cast iron, zirconium in amounts greater than 0.10 per cent tends to promote the development of eutectiform graphite. These irons are characterized by freedom from primary cementite or normal flake graphite and exhibit very little tendency to shrinkage on solidification. In hyper-eutectic low-sulphur cast iron, zirconium causes the formation of a partially nodular graphite structure. A combination of magnesium with silicon-zirconium alloy was found to produce completely nodular graphite structures without the hazards associated with the addition of elemental magnesium.

Jan 1, 1949

By P. MacPhail, G. S. Dobby, I. M. Flint

"The objective of the laboratory work described in this paper has been to develop a method f or producing small gas bubbles at moderate to high gas rates in a flotation column. Small bubbles are particularly important for attaining reasonable flotation rates of fine particles. An ultrasonic aerosol generator has been employed to add frother solution directly to the gas stream. Using porous glass and filter cloth spargers, aerosol frother addition has produced bubbles at 1/2 to 2/3 the diameter of those produced by conventional frother addition to the liquid, at a lower frother consumption.IntroductionGas bubbles are generated in a flotation column most commonly by forcing gas through a porous medium called a sparger. Typical sparger material includes rubber (pierced with small holes) , fabric (such as filter cloth), fritted glass, or porous metal (steel or bronze) . Solid sparger material is suitable for laboratory use; however, for industrial applications a flexible sparger such as rubber or fabric is necessary to prevent the eventual plugging of orfices with solid particles and/ or precipitates. An exception to this is the use of a gas liquid contactor external to the column in combination with pressure release of gas in water, a method that has been demonstrated to produce very small gas bubbles. The typical objective of bubble generation for flotation column purposes is to produce bubbles with diameter of about 0.1 cm (and less) at a gas superficial velocity of 1 cm/s to 3 cm/s. In general, the smaller the bubble, the better. In man y cases, though, there is little , or nothing, gained by generating bubbles less than about 0.05 ern in diameter.Several factors affect bubble size when generated by a sparger: gas rate, orifice diameter, sparger surface area, surfactant type, surfactant dosage, and static head. At very low gas rates bubble diameter is independent of flow rate and is proportional to orifice diameter. At the moderate gas rates encountered in flotation columns bubble diameter, db' is related to gas flow by: db oc vg n, where vg is superficial gas velocity (rate of gas flow per unit column area). For porous steel and filter cloth, n has a value of about 0.25 for vg between 0.2 cm/s and 2 cm/s(2). The magnitude of the effect of orifice diameter at these gas rates is unclear. The effects of frother type and concentration on bubble size issuing from a single orifice have been measur ed by Miagkovaru , shown here in Figure I(IS). The reduction in bubble diameter upon surfactant addition is due to the lowering of interfacial tension created by adsorption of surfactant at the gas liquid interface."

Jan 1, 1988

By Rowena Anderson

Mining companies are now looking for more effective ways to engage the community in public participation. Consensus-based approaches are becoming the most popularly applied way of achieving meaningful public participation. This paper introduces the principles surrounding consensus-building approaches and the processes for getting them started. The Healthy Communities Movement is one such consensus-based approach that offers a well-established holistic model for conceptualizing a healthy sustainable community. It also highlights the importance of public participation as an essential component of achieving a sustainable community. The paper concludes by illustrating how current company-community relations programs can utilize these models.

May 1, 2002

By M. B. Kime

"A set of experimental batch leaching tests studied the effect of pH, time, temperature, and stirring speed on the relative Cu, Co, Ni, and Fe leaching yields of an oxidized copper-cobalt ore sample in an aqueous hydrochloric acid solution. The results were statistically analyzed and modelled using the structural equation modelling method. Models showed that Cu, Co, and Ni leaching yields were strong functions of the leaching time and leaching temperature, whereas the Fe leaching yield depended on the leaching temperature, stirring speed, and pH. Under optimum leaching conditions yields were 99.8% Cu, 82.4% Co, 91.3% Ni, and 30.6% Fe.RÉSUMÉ Une série d’essais expérimentaux de lixiviation en bâchée ont été menés pour étudier l’effet du pH, de la durée d’attaque, de la température et de la vitesse de brassage sur les rendements relatifs de lixiviation du cuivre (Cu), du cobalt (Co), du nickel (Ni) et du fer (Fe) d’un échantillon de minerai de cuivre-cobalt oxydé dans une solution aqueuse d’acide chlorhydrique. Les résultats ont été analysés et modélisés statistiquement à l’aide de la méthode de modélisation par équation structurelle (SEM, de l’anglais structural equation modelling). Les modèles ont montré que les rendements de lixiviation du Cu, du Co et du Ni dépendaient énormément de la durée d’attaque et de la température de la lixiviation ; le rendement de lixiviation du Fe, quant à lui, dépendait de la température de la lixiviation, de la vitesse de brassage et du pH. Dans des conditions optimales de lixiviation, les rendements étaient de 99,8 % pour le Cu, de 82,4 % pour le Co, de 91,3 % pour le Ni et de 30,6 % pour le Fe. INTRODUCTIONThe Katanga province in the Democratic Republic of Congo hosts the northwestern part of the Central African Copperbelt. This region abounds with large, rich deposits of sulfide and oxidized copper-cobalt ores. In general, the main valuable minerals present are malachite (CuCO3Cu(OH)2) and heterogenite (CoO(OH)). Common impurities found in heterogenite are Cu, Ni, Si, Al, Mn, and Fe. The substitution of Co by other cations (e.g., Cu, Ni, and Fe) has an influence on the crystallinity of heterogenite (Deliens, 1974). In general, well-crystallized varieties of heterogenite have lower impurity contents, whereas amorphous heterogenite types usually contain more impurities (Thys et al., 2009). Further, in heterogenite, Co can occur in the 2+ and 3+ oxidation states. The gangue generally consists of quartz (SiO2), talc (Mg3Si4O10(OH)2), kaolinite (SiO2·Al2O3·2H2O), limonite (Fe2O3·3H2O), and goethite (FeO(OH)). Oxidized copper-cobalt ores are often treated by hydrometallurgical methods, whereas sulfide ores are often treated by flotation or pyrometallurgy, depending on their grades. Hydrometallurgical methods typically entail selectively dissolving the metals of interest (Cu, Co, and Ni) in aqueous solutions (leaching), transferring the dissolved metals to an organic solution, and retransferring these to a second aqueous solution (solvent extraction). Copper and nickel are readily dissolved in an acidic aqueous media. In contrast, cobalt is difficult to dissolve, especially if it is present in the third oxidation state; however, this species becomes soluble after it is reduced to Co2+ (Mwema, Mpoyo, & Kafumbila, 2002; Kime & Makgoale, 2016)."

Jan 1, 2017

By L. R. Plitt

A series of experiments were carried out in an effort to develop a universally applicable mathematical model of the hydrocyclone classifier. The design and operating variables studied were: cyclone diameter and height, the inlet, vortex finder and apex diameters, the feed pressure and the solids content of the feed slurry. The model consists of four basic equations which express the cut size ( dso), volumetric split between overflow and underflow, volumetric throughput, and sharpness of separation in terms of the operating and design variables. Although empirical, the model is nevertheless in general agreement with fundamentally derived models. The model clearly 1•eveals the effect of the major variables on the operation of a hydrocyclone. Because of its broad data base and the inclusion of all the major variables, the model may be used without experimental data to predict the operation of cyclones over a wide range of different operating conditions. With operating data, the equations may be modified to serve as an operational model.

Jan 1, 1976

By David Scott, Denis V. Lachance, Daniel Marcotie

"LocationThe Heath Steele mine is located 50 km northwest of Miramichi, New Brunswick.Brief DescriptionHeath Steele is a 2700 t/d, copper-lead-zinc operation which employs conventional crushing, grinding, and differential flotation.HistoryThe Heath Steele mine is located in northeastern New Brunswick approximately 50 km northwest of the city of Miramichi and 65 km southwest of Bathurst. The massive sulphides containing ore values in zinc, lead, copper and silver were discovered in 1953 as a result of a joint venture between the American Metal Company and the International Nickel Company of Canada. The discovery was named after Mr. Heath Steele, manager of exploration for Amco at the time of the discovery.Mill production began in February 1957; however, the mine was forced to shutdown in 1958 due to depressed metal prices and metallurgical problems. It was re-opened in 1962 and milling operations resumed at 725 t/d until 1968 when the milling capacity was boosted to 1450 t/d and then to 2700 t/d in 1969.OreThe main ore zones are massive sulphides with very fine mineral grain. The chalcopyrite, galena and marmatitesphalerite occurrences are finely disseminated.Liberation is accomplished by grinding to 68% to 72% <400 mesh. Average mill feed assays are 0.8% to 1.2% copper, 1.8% to 2.5% lead, and 5.5% to 6.5% zinc, with 60 to 75 g/t silver."

Jan 1, 2000

By Orlando C. Gaspar

Abstract - The presence of fine-grained mineral intergrowths, the complex distribution of deleterious minor elements, and the variable base-metal contents in some assemblages commonly pose technical problems for the processing of volcanogenic massive sulfide ores. The beneficiation of most massive sulfide ores from the Iberian Pyrite Belt requires extremely fine grinding to liberation sizes of K80 = 15 µm to 25 µm. For several deposits, mapping of the ore types and metal zoning patterns has shown that the different ore types are distributed as ore lenses within the massive sulfides. Mineralogical, textural, and metallogenetic studies have provided an understanding of the distribution of both the vertical and the horizontal metal zonation in the orebodies. Because the efficiency of ore processing is affected by ore textures, and because the same mineral commonly has different textures and varies in chemical composition, a relationship between textures of the feed and the middlings must be established for all ore types defined at the deposit scale. Quantitative mineralogical methods have been developed to provide, on a timely basis, the information needed to optimize the concentration processes for the massive sulfide ores at the Aljustrel and Neves-Corvo deposits, Iberian Pyrite Belt, Portugal.

Jan 1, 1997

By Orlando C. Gaspar

The presence of ?ne-grained mineral intergrowths, the complex distribution of deleterious minor elements, and the variable base-metal contents in some assemblages commonly pose technical problems for the processing of volcanogenic massive sul?de ores. The bene?ciation of most massive sul?de ores from the Iberian Pyrite Belt requires extremely ?ne grinding to liberation sizes of K80= 15 µm to 25 µm. For several deposits, mapping of the ore types and metal zoning pat-terns has shown that the different ore types are distributed as ore lenses within the massive sul?des. Mineralogical, textural, and metallogenetic studies have provided an understanding of the distribution of both the vertical and the horizontal metal zonation in the orebodies. Because the ef?ciency of ore processing is affected by ore textures, and because the same mineral commonly has different textures and varies in chemical composition, a relationship between textures of the feed and the middlings must be established for all ore types de?ned at the deposit scale. Quantitative mineralogical methods have been developed to provide, on a timely basis, the information needed to optimize the concentration processes for the massive sul?de ores at the Aljustrel and Neves-Corvo deposits, Iberian Pyrite Belt, Portugal.

Jan 1, 1997

By T. Ivankina, T. Lokajícek, H. Kern, T. Svitek

The knowledge of 3D velocity distribution of P- and S-waves in rocks is very important parameter for interpretation and understanding the nature of seismic anisotropy observed in the earth’s crust and upper mantle. A new high-pressure measuring head was designed and constructed to enable ultrasonic sounding of spherical rock samples in 132 independent directions under up to 60 MPa of acting hydrostatic pressure by means of simultaneous longitudinal and transversal sounding. New measuring system enables ultrasonic sounding of spherical rock samples by using a pair of P-wave sensors and two pairs of perpendicularly polarized S-wave sensors (TV and TH) see Fig.1. Shear wave sensors polarization is oriented according to rotation axis of the sample. Special shear wave gel was used to transfer shear waves between the sample and sensors under acting hydrostatic pressure. An isotropic glass sphere was used to check and calibrate the new measuring setup. A spherical sample of a biotite gneiss from the Outokumpu scientific drill hole was used for testing measurement. There is shown that both, P- and S-wave velocities, can be measured simultaneously up to 70 MPa, respectively. We report data of the 3D velocity distribution of P- and Swaves measured for the first time on a sample sphere of biotite gneiss. We rely, in particular, on the directional dependence of compressional and shear wave propagation and their relationship to the crystallographic (CPO) and shape preferred orientation (SPO) of major rock-forming minerals. The 3D seismic measurements revealed a strong foliation-related directional dependence (anisotropy) of P- and Swave velocities. Ultrasonic measurements were compared with 3D velocity calculations based on neutron diffraction measurements of crystallographic preferred orientation (CPO) of major minerals. Comparison of 3-D velocity distribution (P, S1, S2 and S1-S2) determined by two completely different methods ultrasonic sounding and neutron diffraction is presented. Measurements showed that the intrinsic bulk anisotropy is basically caused by the CPO of biotite constituting about 23 vol.% of the rock.

Jan 1, 2015

By I. R. Muirhead, S. Frimpong

"The mechanization of mining operations in underground coal mines has led to faster cutting rates of coalfaces with increased levels of emission of gaseous and particulate contaminants in the workings. Consequently, the fresh air streams from the main ventilation systems reaching distant workings are often insufficient, ineffective or inadequate and have to be supplemented by auxiliary ventilation systems to create and maintain the required working environments underground. The efficiencies of auxiliary ventilation systems are largely affected by drivers of the system such as the type and capacity of the fan; the type, length, diameter and condition of the ventilation ducting and the distance from the discharge end of the intake ducting to the face. Traditionally, single point measurements of methane gas concentrations using either flame safety lamps or hand-held measuring instruments have been used to assess how safe underground coal workings were. Unfortunately, such occasional measurements of methane gas concentrations do not give an accurate picture of the real gas concentration in the working as they are often taken from the easily accessible locations in working. Continuous monitoring of the methane gas concentration in development headings enables a better assessment of the environmental conditions prevailing there. All variations in the methane concentrations are more easily captured on a continuous monitoring basis than by instantaneous single point measurements. The approach adopted in this work was to continuously monitor the concentration of methane very close to the face and about 60 m outbye in development headings, observe the types of auxiliary ventilation equipment and their sizes being used in the working as well as noting the lengths from the discharge ends of the forcing and exhaust ductings to the face.In this paper, empirical methods are used to calculate the mean efficiencies of the auxiliary ventilation systems in selected development headings in coal mines in North America. This enables the assessment of the effectiveness of the auxiliary ventilation systems and the identification of the system drivers in them. The results show that the efficiencies of the forcing systems ranged from 17.02% to 96.81% while the efficiencies of the overall systems varied from 6.04% to 54.16%. The distance from the discharge end of the intake ducting to the face appeared to be the strongest driver in the performance of the auxiliary ventilation systems studied. It was also noted that when the discharge end of the intake ducting to the face does not exceed 7 m, there were faster purging rates of methane at the face and the efficiencies of the overall auxiliary ventilation system were greater than 50%. These findings are very important in underground coal mining in North America as they will assist to avert calamities, such as the Westray coal mine disaster in 1992 which resulted from the explosion of methane gas, by identifying which components of the ventilation system need special attention to create safe working conditions underground."

Jan 1, 2003

By Richard A. McIvor

"All mine shaft conveyances in Canada and most of the United States that are supported by a single hoist rope or attachment point and used for transporting persons are required by regulation to be equipped with safety catches and mechanisms. These safety mechanisms, commonly called safety dogs, are designed to stop and hold a free falling conveyance, with a full personnel load, in the event of a hoist rope or attachment component failure. The conveyance’s safety mechanism must be tested under dynamic conditions before it is used to transport personnel. This paper will discuss free-fall testing and it’s results on conveyance free-fall tests performed in the test tower at INCO Limited, Sudbury, Ontario.Topics covered will be free-fall tests on various wood types such as B.C. fir, Karri wood and Trusjoist MacMillan Limited Parallamwood (PSL), comparison of deceleration rates versus free-fall velocity and the influence of safety dog tooth design on deceleration rates."

Jan 1, 1996

By Lawrence Nordell

A Conjugate Anvil-Hammer Mill (CAHM) has the potential to replace conventional crushers and SAG mills, with their respective conveyors and stockpiles, in a SABC circuit. It may improve comminution circuit efficiency by 100%. CAHM compresses rock in a more efficient way, similar to 19th century stamp mills, which follows the fundamental research of Schönert (1990 & 1996). CAHM efficiency is being proven through the use of ROCKY (2011) Discrete Element Method (DEM). ROCKY features allow it to simulate realistic comminution. CAHM is customizable with many geometries that are rock-property specific. ROCKY?s wear modeling compliments the structural integrity of the design.

Jan 1, 2012

By A. G. Eccles

"INTRODUCTIONWestern Mines' copper-lead-zinc operations are located in Strathcona Provincial Park, near the geographic centre of Vancouver Island. This park includes Buttle Lake, which flows into the Campbell River water system. The latter provides domestic water for the Town of Campbell River, approximately fifty-eight miles from the mine site.Operation of the concentrator commenced in December 1966, at which time the tailings were discharged into a small tailings pond near the plant. On May 8, 1967 Permit No. 185 was granted to the company, allowing discharge of the tailings, through a submerged outfall, to the bottom of Buttle Lake.Needless to say, the concept of operating a mine within a park, and the discharge of tailings into Buttle Lake generated considerable controversy. However, this has all but been eliminated over the years by the proven effectiveness of Western Mines' pollution control program. In 1973 this program was further upgraded with the addition of an alkaline chlorination plant. Effluent treatment by this method became necessary as a result of process modifications, and has been effective in maintaining the levels of characteristics in the tailings within the ever increasing pollution control requirements imposed on the industry."

Jan 1, 1977

By D. P. Tripathy

A supply chain encompasses all the activities associated with the flow and transformation of goods from the raw materials stage(extraction), through to the end user. Supply chain management (SCM) is the integration of these activities through improved supply chain relationship, to achieve a sustainable competitive advantage and it rests on its ability to provide the right goods and services when and where needed. The supply chain is the vital component of any company?s value chain which links the operating processes to its supplier and customer. The globalization of business promises to offer new and unique challenges for the supply chain competencies of most firms. Challenges will also increase in the environmental aspects of supply chain often referred to as ?Green Issues?. The supply chain of mining industry comprises of the flow of material and information from the mine site, to processing and loading for transport, to the customer. However, due to recent changing environmental requirements affecting mining and mineral processing operations, increasing attention is given to developing environmental management (EM) strategies for the mineral supply chain. This paper focuses on: ? Environmental factors leading to the development of an extended environmental supply chain, ? Additional challenges presented by the extension, ? Performance measures appropriate for the extended supply chain, ? Developing a general procedure towards achieving and maintaining the green supply chain.

May 1, 2006

By Vanessa C. Koppe

During ore body modeling normally additional samples are required to improve resources evaluation and mining planning. At this stage one rises the question about where additional samples should be located. Regular sampling pattern seems to be a reasonable choice, since all the regions within the deposit receive the same number of samples without a clear clustering. Nevertheless, values for certain attributes (grades for instance) from a mineral deposits may behave more erratic in some regions than others. Consequently, by adding samples to these regions could bring more benefit for reducing the uncertainty related to a transfer function such as Net Present Value (NPV), instead of adding samples to location of low grade uncertainty. Thus, for a given number of additional data, the test of a regular pattern and a pattern which add samples on areas of high uncertainty of the attribute of interest is worth. This paper presents an algorithm that allows the construction of these two patterns, automatically, on a software commonly used in the mining industry. The algorithm leads to a fast analysis on the efficiency of the two patterns in reducing the uncertainty associated with a transfer function.

Oct 1, 2009

By G. M. Carrie

Introduction The subject of basic refractories is daily becoming of increased importance in metallurgical processes, and there is a constantly growing necessity for the development of better materials. This fact, together with the realization that Canada possesses one of the best sources of such refractories in the British Empire, if not in the world, made it appear? advisable that the subject be presented to the Empire Mining and Metallurgical Congress at the 1927 meeting. Having been in close touch with developments in the Canadian product during the past five years, G. M. Carrie was requested to prepare such a paper. The Canadian producers of magnesia refractories have succeeded in developing the product to a place where it has almost entirely displaced imported materials from the Canadian market. These developments were made possible by a close study of the methods of preparation of the material, and by an exceedingly careful control of the manufacturing process so as to obtain a thorough blending of the different constituents with the resultant uniformity of composition. This point is very important to the metallurgist, as un-uniform materials are a potent cause of difficulties in most manufacturing processes and the constant trend is towards their elimination. The temperature at which the Canadian material is burned ensures high specific gravity and thorough shrinkage. The grain size of the product is so controlled that the voids are only just sufficient to allow of proper bonding, thus making possible a dense, hard bottom affording high resistance to erosion and shock. Careful proportioning of the constituent elements absolutely prevents disintegration.

Jan 1, 1927

By J. W. Craig

CHROME ore, which is used in Canada in the production of ferro-alloys, in a variety of refractories, and indirectly in many chemical industries, is both commercially important and scientifically interesting. The sight of chromium metal is familiar to all of us in the home, the office, the automobile. Chromium is synonymous with armaments: it is understood to be one of several essential metals in tanks, which played an important role in the defeat of France in the spring of 1940. Chromium, in other forms, comes into our daily lives by way of paint and leather, of the familiar green ginger-ale and beer bottles, and more indirectly in every pound of steel produced in the .Dominion. Necessary to our civilization in peace and war, the ores of chromium occur in many corners of the earth. This paper attempts to describe the chemical constitution of chrome ores, their world distribution, and the various chrome products and their industrial applications in Canada.

Jan 1, 1940

By J. H. H. Chamberlin

"In the Introduction the author briefly discusses the company history as it relates to the development of its contracts with the Japanese steel mills. The main part of the text describes how Coleman Collieries Limited approached the problem of mining coal profitably in thick, steeply inclined seams. For many years a basic room-andpillar system was worked by conventional methods. Main roadways were driven on strike across the mineable area. These roadways acted as haulage routes for coal, materials and men. Rooms were developed to the rise of the main haulage route by pairs of men using air-operated hand picks. As these rooms advanced the miners would lay and extend a sheetiron chute down which mined coal would gravitate to a controlled loading point, where it was loaded into trains of mine cars. Connecting roadways or ""OFFS"" were driven at predetermined intervals between adjacent rooms, forming pil1ars or blocks. Extraction of the blocks followed on a line conducive to good strata control some distance behind the developing rooms. A need for higher productivity, expansion of the operations and a scarcity of qualified miners resulted in the company deciding to mechanize its underground mines. Joy 6 CM continuous miners and 10 SC shuttle cars were selected as being machines that could reasonably negotiate the problems associated with the pitching seam. The equipment, nonetheless, has definite limitations and Coleman therefore developed a modified version of the room-and-pi11ar system such that the miners and cars could work on cross pitch. In the area described, main roadways were driven to the rise on an average gradient of 12 degrees. Panels, which consisted of two parallel roads with interconnecting cross-cuts, were then developed on strike to a boundary point. Blocks formed in the development of the panels were subsequently extracted on retreat. Problems associated with each phase of the operation are thoroughly discussed, together with roadway support methods and equipment used for the conveyance of coal and materials."

Jan 1, 1972

By C. H. Tiernon

"This paper was' prepared to emphasize the part that coal washing tables can play in the development of many of the reserves of coking coals in Western Canada_ It covers a brief history of the development of the coal washing table through the present third-generation unit, which suspends from overhead steel beams and is driven by a counter-rotating gear mechanism. The design and operation of this unique table are covered in detail.An analysis of actual operating data is included, with explicit statistical breakdowns of the table products. The data used were actually produced by operating coal companies, and also produced by the United States Bureau of Mines while gathering data for a research investigation. Table feed capacity is discussed, as well as performance criteria and the parameters of relative table performance. Several typical table flowsheets are described, emphasizing the specific reasons for their use. The paper covers the past and present value of the table to the United States coal industry, and makes mention of the newest addition to the family of suspended, multiple-deck, counter-rotating, gear-driven, coal washing tables, the CONCENCO ""88"" Deister table."

Jan 1, 1973

By R. S. Adhikari

The changes in defects patterns or in element condition index during visual inspection of bridges are primary concerns for inspectors. This paper presents a new approach for change detection of defects in bridges by identifying changes in texture patterns through spectral analysis of digital images. The commonly used method for change detection is image differentiation. This subtraction method requires images to be of same size, scale, and rotation. However, no two images are same in real practices. Thus, image registration is required to align images and to produce change maps. This process is tedious and it is difficult often to achieve a good registered image. But, the change detection task can be readily modeled in frequency domain for texture patterns discrimination and also for quantifying their properties. This paper proposes a novel approach for change detection by transforming digital images into Fourier spectrum. In new coordinate system, 1-D signature functions can be drawn which facilitates easy comparison of textures in different directions. The proposed methodology provides useful tools for comparison of inspection history graphically and quantitatively. In practice, expensive sensors are used to detect subtle change in defect patterns. The proposed method can be used to detect any subtle change in defect patterns using digital images at much lower cost.

Aug 1, 2013