Search Documents

By T. C. Cheng, G. P. Demopoulos

It is the object of this paper to discuss various options for improving the hematite process in terms of increased throughput hence lower capital cost and production of saleable quality hematite. With reference to increasing the throughput of the process, it has now been determined via the analysis of Akita Zinc Co's continuous industrial autoclave performance data that the process kinetics is limited by the rate of the hydrolytic precipitation reaction. By correlating the hydrolytic precipitation rate to supersaturation ratio, it is shown that accelerated kinetics can be achieved via the following measures: (1) in-situ neutralization with addition of zinc calcine; (2) elevation of temperature; and (3) dilution of feed; of which, the first one was retained for further evaluation. According to presented estimates, addition of calcine, amounting to only 2.6% of the total zinc calcine processed, can allow for shortening the retention time by at least 50%. Such drastic shortening of retention time may be either used to increase the throughput of a given autoclave circuit or alternatively to release autoclave capacity for clean hematite production. Hydrothermal treatment of the crude hematite product proved effective in producing clean hematite as according to laboratory tests, hence allowing the sulphur content of hematite to be reduced from around 4% to less than 1%. A conceptual flowsheet incorporating in-situ neutralization for accelerated kinetics with hydrothermal upgrading of crude hematite without sacrificing production capacity and with minimum upset of the plant's water balance is described.

Jan 1, 2004

By J. M. Hong, H. K. Zheng, R. Hu, C. B. Zhou

The Jinping-I double curvature arch dam, located in the middle reach of the Yalong River and with a maximum height of 305 m, is the world highest dam of the same type that has been completed. Since the second and third periods of the reservoir impounding, after which the reservoir water level was raised by about 200 m, a significant amount of leakage was observed out of the drainage holes deployed in the lowest drainage tunnel at the left-bank abutment at EL. 1595 m, with a pressure of 0.3 MPa at one typical hole when it was blocked. In this study, a number of analyses including water quality analysis, digital borehole imaging, tunnel geological mapping and in-situ groundwater monitoring were performed to investigate the source of leaking, the leakage passages and the performance of the grouting curtains. An inverse modeling procedure combining the orthogonal design, finite element forward modeling of the transient seepage flow, artificial neural network and genetic algorithm was invoked to further evaluate the permeability of the foundation rocks whose permeability was underestimated in design, using the in-situ measurements of flow rate and piezometric head. The geological structures that lead to the leakage were identified and the seepage flow behaviors in the dam foundation and the left bank abutment were assessed. Given the connectivity nature of the sub-vertically oriented fractures that induce the leakage event, it is found that some of the drainage holes with relative larger amount of discharge could be closed or blocked for reducing the amount of leakage without remarkably increasing the pore water pressure in the foundation rocks.

Jan 1, 2015

By Dave Bulled

"This paper describes the design of a molybdenite flotation circuit using FLEET technology applied to kinetics data produced from laboratory flotation testing and distributed across the blocks of a mine plan using a geostatistical approach. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the kinetics estimates of each block of ore in the mine plan. The final design then included a quantification of risk based on the accuracy of the block flotation kinetics and model fitting. The design made reference to the extensive technical reports describing earlier metallurgical test work including some pilot plant work over thirty years ago.The testing involved conducting MinnovEX Flotation Tests (MFT) to determine the rougher flotation kinetics at the specified reagent conditions and rougher-cleaner tests to determine the change in kinetics resulting from regrind. These flotation kinetics were used within FLEET simulations to create a full-scale flowsheet and plant design including recommended equipment sizes and the forecast of operating results. Measurement of detailed flotation kinetics for a wide range of samples allowed the effect of size of grind and efficiency of classification (i.e. width of size distribution) to be predicted for the whole ore body.INTRODUCTIONAdanac Moly Corp. proposed to develop a 20,000 ton per day mill to produce high quality molybdenite concentrate from its Ruby Creek resource in north-western British Columbia. It is a relatively clean low grade porphyry-monzonite occurrence containing minimal quantities of other sulphides such as chalcopyrite, pyrite, sphalerite and galena. Molybdenite occurs mainly as coarse flakes with lesser amounts of finer sized values. An optimum plant design was required to can achieve the predicted operating results, at a known level of risk, while treating the variability inherent in the ore body."

Jan 1, 2007

By Erwin L. Zodrow

THE AUTHORS welcome this timely opportunity to comment o n a paper by MacLean and Merner (" Room-and- Pillar Mining at the Prince Mine of the Cape Breton Development Corporation " , ClM Bulletin , June 1978, pp. 59-62) concerning the rock falls and their relation to "a change in the strata". First, however, it is proper to express our gratitude to the Cape Breton Development Corporation, and in particular to A. R. MacLean, for making it possible for us at the College of Cape Breton to start two new collections. The first of these is a fossil plant reference collection from the Sydney Coalfield, Cape Breton (Upper Carboniferous period) , and the second is a documentation of the role o f pyrite in the formation of hydrated sulphates (samples from No. 26 Colliery, 1-B Mine, and the Prince Mine at Point Aconi). Conditions of sedimentation in the deltaic-type basin of the Upper Carboniferous time in the Point Aconi area were such that on the (coal) swamp, now represented by the Stubbart (or Hub) seam , (a) clays of varying thickness and extent were deposited , (b) biogenetic sulphur was introduced and (c) flora were buried. These are essentially the culprit s that make rock falls possible and at the same time predictable over large areas (in the present mine). The clays lithified to become shale, and biogenetic sulphur combined with iron to become pyrite (marcasite?), which exists as nodules and in fine-grained layers.

Jan 1, 1978

By F. Y. Hsiao, H. C. Kao

Underground excavation in hard rock is normally stable at shallow depth except for wedge failure. However, the excavation depth is rapidly increasing recently. In high overburden stress condition, the integrity of rock would be destroyed with degrading rock strength. Therefore, understanding both the peak and the post-peak strengths of hard rock are necessary to assess the tunnel stability at depths. The characteristic of the post-peak strength is seldom studied in Taiwan in the past. Various estimation methods for the post-peak strength degradation were briefly reviewed in the paper. Based on the Geological Strength Index (GSI) system is widely used in the determination of the rock mass strength, the quantitative residual GSI system was adopted to estimate the possible strength degradation for a hydraulic tunnel in Taiwan. The Mohr-Coulomb model (no strength degradation) and the post-peak strength degradation model (strain softening model) were used to simulate the excavation of the case tunnel at different depths. The analyses demonstrate that the tunnel is in stable condition at 600m of depth. And the effect of the postpeak strength degradation on tunnel deformation is progressively significant with increasing tunnel depth. Approximate 3-5 times of increase in crown settlement and horizontal convergence would occur when post-peak strength degradation are considered at 2400m of depth. Severe tunnel deformation may endanger the tunnel stability. Modeling results reveal that the post-peak strength degradation has a great effect on tunnel stability under high overburden stress condition, which should not neglect in deep tunnel design.

Jan 1, 2015

By J. K. Gowans

"INTRODUCTIONTo bring a mining property into production in the Canadian High Arctic a company must deal with the harsh environment, the short shipping season and the high cost of labour. In trying to minimize the effect of these factors, the concept of a barge-mounted process plant was investigated as an alternative to the conventionally built concentrator. Cominco's previous experience gained at the Black Angel Mine on Greenland's west coast suggested that this would be a practical alternative.The normal shipping season at Little Cornwallis Island is approximately six weeks long, from mid-August to the end of September. All equipment and materials must be delivered during this small ''shipping window."" The logistics problems are enormous; if the conventional approach had been used the major process equipment would have been delivered to Little Cornwallis Island at the same time as the completed barge actually was! Construction would also be starting at the start of the worst climatic conditions, the Arctic winter. Nine months production was gained by opting for the ""Barge"" approach.What the Arctic winters do to the shipping season, so do they affect the productivity and the cost of labour. Construction labour must come from southern Canada. Thus higher transportation costs and higher wage rates, with more overtime and incentives, increase the labour costs to approximately 50% over normal southern rates. Couple these rates with the lower productivity involved with men working in the extreme cold temperatures and the net effort is worth avoiding. A process plant being constructed in Southern Canada can take advantage of more accessible labour at lower costs, increased productivity and a faster construction schedule. The barge concept must still deliver the equipment and materials during the ""shipping window"" but it can in the completed form."

Jan 1, 1983

By Andre Panteleyev, Charels S. Ney, John M. Anderson

"Sam Goosly prospect, 22 miles southeast of Houston, B.C., was discovered in 1967 through geochemical reconnaissance. Soil sampling interpreted with respect to an east-to-west ice movement led to drilling targets.Mineralization is in a window of rocks thought to be Hazelton Group surrounded by Tertiary volcanic rocks and intruded by two stocks separated by about one mile. A westerly quartz monzonite stock is dated 61.1 m.y. and an easterly gabbro-monzonite complex is dated 52.5 m.y. The Tertiary volcanics are trachyandesites shown by the B.C. Department of Mines and Petroleum Resources to be in part extrusive equivalents of the gabbro, and they overlie Hazelton rocks uncomformably. Copper-molybdenum mineralization is sparsely developed in the westerly stock. Silver-copper mineralization forms an elongate west-dipping slab between the stocks in Hazelton rocks, which are continuously pyritized. The gabbro stock is not mineralized, but some dikes related to it are slightly so. Tertiary rocks are pyritized, but are not known to carry copper-silver mineralization. Hazelton rocks are divided into a lower conglomerate, an intermediate pyroclastic unit and an upper mainly sedimentary unit. They form a west-facing homocline. Coppersilver mineralization resides in the pyroclastic unit, mainly in a massive dust tuff through which are lenticular units of lapilli tuff. Well-mineralized rock is typically a breccia of light fragments in a dark chlorite-sulphide matrix. Sulphides are pyrite, chakopyrite and locally pyrrhotite, with very minor tetrahedrite, s phalerite and other sulphosalts. Rock alteration is predominantly a pervasive pyrite-sericite type, with widespread tourmaline, scorzalite, gypsum, ankerite and traces of fluorite. The most evident control of the copper-silver mineralization is the gross parallelism, over a strike length of 1.5 miles, to Hazelton strata, particularly a massive dust .tuff unit. In detail, mineralization crosscuts bedding and there is no appreciable banding within sulphides . A strictly syngenetic origin is untenable, but some initial concentration in a volcanogenic environment with subsequent modification by thermal processes seems likely."

Jan 1, 1972

By Ralph Harris, Xia Qi, Frank Komsic

"Gold cyanidation kinetics which are often limited in commercial operations by the rate of oxygen dissolution from gas bubbles into the slurry, are discussed. Emerging technologies for improving the rate of oxygen dissolution are compared and the gas efficiency, energy use and operating performance of inverted cones and a device based on a jet diffuser are examined. The effect of solids loading is also reviewed and a relationship between operating parameters and the kilograms oxygen dissolved per kilowatt-hour is presented.Inverted cones are shown to create slurry settling problems at high gas flow rates and surface tension lowering agents are shown not to greatly improve the overall rates of oxygen dissolution.The novel jet diffuser technology operates at a range of gas to liquid ratios that improves its energy use over conventional technology and the performance of a number of designs are discussed.Gas efficiencies as high as 35% were observed with the novel diffusers at 40 cm diffuser immersion and are expected to increase at greater immersions. Energy use of 1.8 kg 02 I kWh were estimated for prototype full size diffusers operating at 100 cm immersion. Energy use of 3.S kg 02 /kWh is conservatively expected at 600 cm immersion.IntroductionGold ExtractionGold that can not be recovered by gravity separation can be recovered by either the Merrill-Crow process or the newer carbon in pulp (CIP) or carbon in leach (CIL) processes 1. Reductions in operating costs and improvements in gold recovery are central mill operating strategies. The present paper examines the potential for improvement that can be achieved in the gold cyanidation step of gold recovery. This paper introduces a number of emerging technologies and provides a basis for comparison of the performance. It shows that the basis for comparison of a particular technology depends on the type of gold extraction circuit employed and the type of reactants employed."

Jan 1, 1996

By M. J. Michaud, M. J. Lavigne

"A cornerstone of any successful mining project is an understanding of the mineral assemblage and metal distribution comprising the deposit. Knowledge of the precise mineral/ metal zoning enables an operation to utilize different mining and processing methods optimized for different parts of the deposit. The Lac des Iles mine, located in northwestern Ontario, is one operation that depends on a good understanding of these issues. Current resources for the Roby Zone total 94.1 Mt grading 1.66 g/t Pd, 0.18 g/t Pt, 0.14 g/t Au, 0.062% Cu, and 0.053% Ni.The Roby Zone occurs within the gabbroic portion of the Lac des Iles intrusive complex and consists of three compositionally and texturally different ore types with variable PGE, base and precious metal contents. PGE occur as sulphides and bismuthotellurides in net-textured sulphides, coarse sulphide blebs and as finegrained inclusions within secondary silicates.Knowledge of the precise mineral/metal zoning has directly and indirectly improved several operational aspects, including resource modelling, mining, and processing. For example, metallurgical recoveries have been increased by up to 3% to 5% and concentrate grades have increased by up to 100%. IntroductionLac des Iles Mines Ltd., a wholly owned subsidiary of North American Palladium Ltd., owns and operates a 3000 t/d open pit mine and concentrate facility, located 100 km north of Thunder Bay in northwestern Ontario. The Lac des Iles PGE-gold-copper-nickel mine has been in commercial production since 1993 and in 1997, produced 1.8 million grams of palladium, 127 000 g of platinum, 114 000 g of gold, 438 000 kg of copper and 354 000 kg of nickel (North American Palladium Ltd., 1998).Under the Industrial Research Assistance Program (IRAP), a two-year study of the mineralogy of the Roby Zone was undertaken with a goal of improving the profitability of the mine. Geological mapping, petrography and geochemistry of the Roby Zone were completed during this study. Utilization of the detailed mineral/metal zoning identified as part of this study was implemented at the mine and shown to positively impact many operational aspects including mining and processing."

Jan 1, 2003

By H. A. Schnell

"The Phase I Mill at Cluff Lake in northern Saskatchewan was designed to accommodate a very specific high grade uranium ore. As this high grade ore was depleted, construction was undertaken on a new mill circuit (Phase 2) to process a more conventional lower grade ore deposit.The Phase 2 Mill expanded the ore throughput to 800 tonnes per day. The new process employs crushing, grinding, leaching, counter—current decantation, solvent extraction and magnesia yellowcake precipitation and drying to produce a yellowcake concentrate.This paper discusses the process decisions required for this expansion and outlines the new mill circuit. Included is a review of the start up in August, 1984.1.,INTRODUCTION The Cluff Lake Uranium deposit is located 720 kilometers north of Saskatoon in northern Saskatchewan. A high grade deposit was discovered in 1970 with the first production taking place in 1980 after lengthy hearings. The original mill (or Phase 1 Mill) was specifically designed to accommodate this very high grade ore for a very limited plant life.Pilot plant work was carried out in 1981 on the other lower grade ores found in the immediate Cluff Lake area. Feasibility and process selection studies were then undertaken as the Phase 1 mill was nearing its end of life. These studies were completed in March 1983 when approval was given to construct the new Phase 2 mill."

Jan 1, 1985

By K. V. Konigsmann

"The results of Mr. Klymowsky's research confirm the essential role played by oxidation products in the flotation of base metal sulphides. They invite a discussion on the subject of aeration which I may open by a brief description of the development and current practice of aeration. The first installation of pre-flotation aeration in Canadian milling practice was undertaken during the years 1928 and 29 at the then new Noranda Mill. C.G. McLachlan and his collaborators demonstrated that the flotation differential between chalcopyrite and iron sulphides was enhanced by aeration in soda ash alkaline pulps. The ores treated contained more than 80 per cent sulphides. It was proposed already then that the products of mineral oxidation assisted copper and retarded iron sulphides, at least pyrrhotite flotation. The concentration of thiosulphates was used as a measure of the progress of oxidation. Several papers by C.G. McLachlan elaborate on this subject.The aerator was also used as classifier since it was held that aeration, i.e. controlled oxidation, should go hand in hand with creation of new mineral surfaces. Grinding mills and aerators were placed in closed circuit. Figure 1. This aeration was essential for successful separation at Noranda.Following the application of aeration at Noranda the technique was applied to existing mills in N.W. Quebec. Impressive improvements in concentrate grades and recoveries were obtained. It was observedthat the zinc flotation benefitted from aeration as much as the preceding copper float. In the late forties and fifties the aerator classifier was installed in new mills associated with the Noranda group. A diagrammatic sketch of the Quemont flow-sheet (figure 2) may serve as a typical example."

Jan 1, 1973

By C. Veloo

"Westmin Resources operates a mine/mill complex at Myra Falls and produces copper and zinc concentrates with minor associations of gold, silver, and lead from a polymetallic, massive sulphide orebody. Mill flotation performance has historically been plagued by periods of uncontrollably high circulating loads leading to low concentrate grades and below optimal tails. This led to a detailed examination of the flotation process. Locked cycle, and pilot plant data are presented. In addition, plant design and commissioning as well as column cell details are discussed. A comparison between actual and predicted performance is also presented. Benefits realized are higher copper and zinc concentrate grades and improved zinc recovery.PrologueMyra Falls Operations is located at the south end of Suttle Lake in Strathcona Provincial Park. Access to the mine site is provided by a 90km paved highway from Campbell River, British Columbia.The mine and facilities are nestled in the narrow Myra Valley between Mount Phillips and Mount Myra. These steep, rugged mountains rise from the valley floor at an elevation of 900 feet to summits of almost 6000 feet. The steep slopes are heavily wooded with fir, hemlock, and cedar up to an elevation of 4000 feet where a transition to alpine meadows occurs. The summits are craggy rock faces, some capped with glacial ice. Myra Creek winds its way through the valley dropping several hundred feet into Suttle Lake. Precipitation is high at over 100 inches per year, which may include up to 10 feet of snow in winter. The temperature may range from 32° C in summer to -18° C in winter.Myra Falls began production in 1965 with the Lynx Mine, supplemented by the Myra and Price Mines in subsequent years, feeding a 950 stpd mill up until the middle of 1985 when the H-W mine was brought into production. The original mill was replaced with a modern 2700 mtpd facility and in 1988 production was increased to 4000 mtpd.Both Lynx and H-W mines are currently in production producing an average of 3650 mtpd. The ore minerals are primarily sphalerite and chalcopyrite, with subordinate galena, bornite, tetrahedrite, and electrum."

Jan 1, 1992

By L. Parthasarathy, S. K. Pan, M. P. Srivastava

"Total iron ore reserves in India, as reported by the Indian Bureau of mines, are 23.6 billion tons. Hematite iron ore reserves constitute about 45 % of the total reserve. If we go by the National Steel Policy-2005 projections, India’s supply of hematite iron ore would not last more than 40 years. Laboratory investigations were carried out for the development of a process flow sheet for treating low grade as well as Banded Hematite Quartzite (BHQ) iron ore. The purpose of these investigations was to aim for better resource utilization.Beneficiation studies were conducted on samples of low grade and siliceous iron ore from the Dalli mines, a captive mine of the Bhilai Steel Plant and BHQ ore from Southern states of India. The process flowsheet, developed for upgrading of low grade iron ore, incorporates wet screening of the ore at 0.5 mm, followed by grinding of the +0.5 mm fraction to below 0.5 mm. The whole –0.5 mm fraction, after grinding, was treated in a conventional hydro-cyclone and stub cyclone followed by treatment in Wet High Intensity Magnetic Separator (WHIMS). This resulted in a concentrate product having >66% Fe content from a feed containing 55.5% Fe with an iron recovery of 48 %. The process flowsheet developed for treating BHQ ore in the laboratory resulted in an increase in iron grade in the concentrate from 43.4 to 61.3 Fe % with a yield of 51.7 % .INTRODUCTIONThe classification of Indian iron ore resources have been made compatible with United Nations Framework Classification (UNFC), which is more scientific and has been adopted in most countries in the world. Iron ore reserves and resources estimated using the UNFC classification system, as of April 01,2000 are about 12,906 million tons of hematite ore and 10,628 million tons of magnetite ore. The Indian Bureau of Mines (IBM) has given a breakdown of these reserves by designation as either lumps or fines of hematite iron ore (Table 1). The percentage of the reserves reported lumps and fines are 42 and 34% of the total reserves respectively. High grade iron ore is less than 10% of the total reserve."

Jan 1, 2008

By Michel Brissette

"To recover more valuable ore and considering the complexity of minerals, the needs to grind finer is increasing. To reach the desired fine grinding targets, using the existing grinding media size, the energy consumption is increasing exponentially. As already proved at this conference, small grinding media represents the best potential to improve grinding efficiency. How do the small grinding media perform in industrial grinding mills?The use of small grinding media in regrind mills proved that finer grinding can be achieved at lower energy consumption. In ball mills, smaller grinding media versus 25 mm media generate a power saving from 10% to 44%. In vertical stirred mills, the power saving increases from 20% to 60%. More potential savings have been identified.For the same operating conditions, how a vertical stirred mill is performing compared to ball milling? In regrind application, a vertical stirred mill with small media (5-12 mm Millpebs) will require at least 62% less energy than a ball mill charged with 25 mm grinding media.INTRODUCTIONIn some mining applications, fine grinding is needed to liberate further the valuable ore. The purpose of regrind mills is to achieve the last stage of grinding before final flotation stage: the cleaners. In part because of high prices of small grinding media as well as availability, the most widely used size of grinding media is 25 mm.When calculating the recommended ball top size from Bond’s formula (Bond, 1961), the size for regrind applications is much lower than 25 mm. Today, the barrier for small grinding media is broken. They are best suited in regrind application. The size of grinding media is one of the most important variables affecting the mill efficiency (McIvor, R., 1997; Nesset, J.E., Radziszewski, P., Hardie, C. & Leroux, D.P., 2006).Conventional ball milling was discarded for fine grinding because of its very poor energy efficiency (Zheng, J., Harris, C.C. & Somasundaran, P., 1994; Yan, D.S., Freeman, M. & Dunne, R., 1995). Therefore, new technologies as stirred mills were developed to grind finer more effectively. Three fundamental questions should be asked. What is the best fine grinding technology? What should be the best media size to use? Is it possible to grind finer by using less energy with the existing regrind equipment?"

Jan 1, 2009

By R. H. Colquhoun, A. W. Bolland, H. J. H. Pieterse

"American Barrick Resources Corporation acquired the goldstrike property in north eastern Nevada in early 1987. Since that time, the company has undertaken an extensive development program. This paper will overview the milling, autoclaving, and heap leaching facilities which are part of the $400-million Betze development plan. Gold production at the Mine has increased from 40,000 ounces per annum in 1987 to more than 500,000 ounces in 1991. And in 1992 Goldstrike will be the single largest North American gold mine when it produces 1,000,000 ounces.1. SUMMARYAmerican Barrick Resources Corporation acquired the Goldstrike property in northeastern Nevada in early 1987. Since that time, the company has undertaken an extensive development program. This paper will overview the milling, autoclaving, and heap leaching facilities which are part of the four year, $440- million Betze Development Plan. Gold production at the Goldstrike Mine has increased from 40,000 ounces per annum in 1987 to more than 500,000 ounces in 1991. In 1992, Goldstrike will be one of the largest North American gold mines, when it produces appro approximately 1,000,000 ounces.2. INTRODUCTIONAmerican Barrick Resources Corporation is in the process of developing the Betze gold deposit, located on Barrick's Goldstrike property in the Carlin area of Nevada, U.S.A.The Goldstrike Mine has 17.9 million ounces of proven and probable reserves and an additional 460,000 ounces of possible reserves. Additionally, the Purple Vein deposit, one mile north of the Mine, is expected to add at least 4 million ounces of reserves by year end 1991.The Goldstrike ore body contains both oxide and sulphide ore. The largest part of the reserves are contained in the high grade, deep sulphide ore. Mining of the sulphide ore contained in the Betze deposit involves the removal of large quantities of overlying oxide ore. Oxide ore is treated through one of the following processes:-"

Jan 1, 1992

By C. H. Stockwell

"The Precambrian rocks of southeastern Manitoba contain a great variety of mineral deposits, including gold, chromium, copper, nickel, lithium, tin, beryllium, tungsten, and molybdenum. Although considerable interest has been shown from time to time in each of these types of deposit, production to date has been almost entirely in gold. This has had a value of about $26,000,000 and has been derived chiefly from the San Antonio mine, with lesser amounts from the Central Manitoba, Gunnar, Beresford Lake, Ogama-Rockland, Diana, and other properties.Most of the deposits lie within volcanic and sedimentary rocks or within basic intrusions cutting these rocks. These favourable rocks occur in several areas, which have been given local names and are separated from one another by large bodies of granite (Fig. 1).In general, the several areas are characterized by different types of mineralization. Thus, the Rice Lake-Beresford Lake area contains numerous gold deposits and has yielded almost all the gold production to date; the Maskwa River, Euclid Lake, and Oiseau River areas are, on the whole, characterized by deposits of chromium, copper, nickel, lithium, tin, and beryllium; and in the West Hawk Lake area there are deposits of gold, tungsten, molybdenum, and lithium.As might be expected in a district containing such a variety of mineral deposits, the structural conditions controlling their deposition also vary greatly. It is, accordingly, convenient to discuss the structural geology and mineral deposits of each of the more important areas separately."

Jan 1, 1954

By K. H. B. Wenzl

"Since the autumn of 1973, the world's attention was captured by the startling revelation that conventional energy supplies were not inexhaustible but were in fact quickly dwindling with future shortages imminent until lagging exploration and technology yielded additional energy sources to catch up with the spiralling increase in demand. This situation was precipitated by the Arab Oil Embargo and the resulting soaring cost of world crude oil.During the past few years there has been tremendous activity in the energy field which has had a direct impact on the Inca Metals Company Ontario Division operations. The company's reaction has been to establish an energy management program which will be described later in the paper. First, a brief description of the Inca Metals Company and the primary energy resources which are utilized will assist in putting the program into perspective.The Inca Metals Company, a unit of Inca Limited, is responsible for the production and sale of primary metals products worldwide. The company's operations in the Sudbury District include mines, ore concentrating plants, a Smelter, Nickel and Copper Refineries and an Iron Ore Recovery Plant. The Ontario Division also has a mine and concentrating plant in Shebandowan near Thunder Bay, and a metals refinery at Port Colborne. Inca is the largest producer of nickel in the non-communist world and is also a major producer of copper and platnium group metals."

Jan 1, 1978

By R. M. Kleine

In the fall of 1968, Sheridan Geophysics leased the Renzy Mine property 50 miles northwest of the town of Maniwaki, Quebec. A 500-tpd flotation mill was dismantled at Belleterre, Quebec, trucked into the mine over a winter road and re-erected during extreme winter conditions. Approximately one billion gallons of water were removed from Renzy lake to expose the orebody. A 3,000-hp diesel generating plant and a self-supporting community were set up during the early part of 1969. This was a remark-able achievement considering that most of the work, including the pouring of foundations and the draining of the lake, had to be done during the winter months. Despite this, the project was completed ahead of schedule and one million dollars below budget. The mill is now treating an average of 800 tpd.

Jan 1, 1970

By T. Backers

In fracture mechanics modeling the rock mass is seen as the combination of rock material and fractures, which are evident on different scales. The activation and propagation of fractures dominates the stability and performance issues as well as fluid flow potential. Once fractures have started to grow into each other and create through going separations, stability of rock engineering constructions may be violated. Further, as fracture mechanics inherently incorporated a scaling law in the form of the participating fracture length, scaling issues can be more accurately mirrored. This contribution highlights some examples of application of a fracture mechanics based code on some rock mechanics issues such as numerical laboratory experiments, borehole stability or the creation of fluid pathways due to underground constructions. The results show explicitly the creation of fractures and connection of existing ones, and hence the safety and performance issues. It has to be concluded that the basis for frequent application of fracture mechanics on specialized challenges in Geomechanics is laid, and the needs for future developments are defined.

May 1, 2009

By R. J. McLeod

"CONTROL STRATEGYThe Lake Dufault Division of Falconbridge Copper Limited has been concentrating a complex copper zinc ore since late 1964. An ARL X-ray on stream analyzer was installed in 1966 for process control. A Digital Equip-ment Corporation PDP8 was added in 1968 for more complete control. To improve the system the computer was exchanged for a Moded PDP-81 in 1971.The new computer is time sharing with 8K core memory and 32K disc storage. A new interface was installed to accommodate 14 X-ray streams and additional analog signals for process control. The system gave us additional capacity and flexibility to make changes in operating programs and control strategy while on line. As the computer is used for process control a modified focal language was chosen as the operating language for ease of operation. This language is more suitable for process control than for statistical work.The main components of the control system are(a) Computer(b) Interface(c) Production Control X-ray Quantometer(d) Teletype terminals(e)Reagent feeders(f) Sample SystemThe operation of the system consists in the computer selecting the various streams to be analyzed by a PCXQ Quantometer. When the flowing sample is presented to the X-ray the intensities of the various elements are read by the computer from analog to digital converter, the assays are then computed. From the tonnage and assays the computer is programmed to determine the amount of reagent added to various parts of the circuit. The computer drives the feeders via the interface for the required amount of reagent. After following a certain sequence the computer prints out the performance and control data on an ASR35 Teletype. The data is printed out approximately every seven minutes. Any des¬ired changes in the program or strategy can be made during operation via an ASR33 Teletype connected to the computer."

Jan 1, 1973