Search Documents

By N. W. Johnson

"Two analysis tools which have been applied to problems in industrial flotation processes are the application of kinetics and detailed mineralogical or liberation data, both on a size-by-size basis. This paper describes practical examples of the application of kineticsto examination of the entrainment recovery mechanism, the retardation of valuable minerals at the commencement of flotation sections and the resolution of problems related to valuable species with reduced rate constants at the end of sections. Examples of the usefulness of size-by-size liberation data for monthly composite samples of products from a concentrator are also described.IntroductionMuch of the published industrial flotation data on the behaviour of minerals in various size fractions have been obtained from specially conducted surveys with a duration of several hours. Such data are very valuable and provide a record of the behaviour of the entire flotation plant or sections during the interval of the survey. Some examples from the literature can be cited Cameron et al. (1971), Lynch et al. (1981), Frew (1982). Less attention has been given to the value of complementary sized data derived from compositing shift or daily inventory samples over an interval of one or several weeks with repetition of the procedure at the completion of each interval. Mineralogical point count data of the size fractions of such samples and data interpretation are rare in the literature.Kinetic data on the behaviour of valuable and gangue minerals in various size fractions have been reported often for flotation banks. In the experience 0 f the writer, there has been a tendency among operating metallurgists to ascribe problems in the flotation process to rate constant values for gangue minerals which were believed to be unsatisfactorily high. Less attention has been paid to the value for the rate constant for the valuable mineral over the length of a particular bank.Examples of the types of data which were mentioned previously have been obtained from the lead-zinc concentrator at Mount Isa Mines Limited. The various types of data have been collected to evaluate their worth in order to provide relevant information for both research and operational aspects of the plant."

Jan 1, 1987

"The McArthur River uranium deposit is the single richest uranium ore body developed in the world to date. The ore body’s average grade is 15% U3O8. Proven reserves are in excess of 450 million pounds. The grinding circuit is located underground. The ground ore is pumped to a surface facility where the slurry is thickened and loaded into containers for shipping to the Key Lake mill 78 kilometers to the south.The paper will briefly describe the mining method employed. The underground ore handling and grinding circuit, and surface facilities including slurry load out, wastewater treatment and the freeze plant will be described in detail. The paper will emphasize radiation and safety procedures that are followed to minimize operator exposure to radiation risks.LOCATIONThe McArthur River mine is located 78 kilometres north of the Key Lake mill. It is located at latitude 57’ N in northern Saskatchewan, within the southern boundary of the Athabasca formation. The nearest town is Pinehouse, located 320 kilometres to the south. Access to the mine is by an all weather road and by a private airstrip.HISTORYThe McArthur River Operation is jointly owned by Cameco Corporation (69.805%) and Cogema Resources Inc. (30.195%). Exploration for uranium in the McArthur River area started in 1980 by the Saskatchewan Mining Development Corporation, a predecessor company of Cameco.In 1984, a 12-kilometre long basement conductor was identified at a depth exceeding 500 metres. Systematic exploration drilling of this conductor resulted in the discovery of the P2 North deposit. Subsequent surface drilling programs from 1989 to 1992 delineated a narrow ore zone over a strike length of 1700 meters at a depth of 500 to 600 metres. At this time, geological reserves for the deposit were estimated to be 2.4 million tonnes at a grade of 5.0% U3O8 for a uranium content of 260 million pounds U308"

Jan 1, 2001

By Shahé Shnorhokian

A study was conducted on the seismic activities and associated rockburst events that took place at an underground Canadian metal mine over a period of five years. In the first stage, a back analysis of the microseismic database led to the identification of clusters of major events. The locations of these clusters were identified with respect to the local geology and the planned mining sequence. In the second stage, a numerical model was constructed using the finite difference code FLAC3D to simulate the in-situ stress, mine geometry, local geology, and stope sequence. Mining-induced stress fields were compared against two rockburst events that took place during this period, as well as against the various geologic units present. It was shown that by combining microseismic analysis and numerical modeling, it was possible to provide a basis for evaluating the influence of the in-situ stress regimes and stope sequencing on mining-induced seismic response.

May 1, 2011

By D. Imeson, T. Grammatikopoulos, G. Pearse, M. Aghamirian, C. Mohns

"Spodumene mineral is a source of lithium for lithium ion batteries. Thus, the production of a spodumene concentrate with an approximate grade of 6% Li2O is targeted. Traditionally, spodumene is concentrated by froth flotation using fatty acid as the collector. Amine collector can also be used to float mica ahead of spodumene as required or feldspar from the spodumene tailings. Slimes have a negative effect on spodumene flotation and they are commonly separated by scrubbing and de-sliming prior to spodumene flotation. The main losses in spodumene flotation typically occur in cyclone overflow, scrubbing slimes, spodumene flotation tailings and mica concentrate. In recent years, dense media separation (DMS) is the main concentrating process in Australian spodumene operations. In these operations, DMS is efficient at generating coarse grain concentrates and rejecting large portions of silicate gangue, thereby directly reducing the milling cost. The ore should be crushed to 3/8” or coarser while further crushing is possibly necessary on the middling particles to scalp further spodumene. The DMS feed should be classified to remove fines (typically -0.5 mm particles). The final middlings and undersize fractions could then be processed by flotation. The main requirement in DMS operations is to have good spodumene liberation at relatively large grain size. This paper reviews the most significant DMS and flotation parameters in spodumene beneficiation. The treatments of different minerals in the spodumene ore are also addressed.INTRODUCTION A number of laboratory/pilot plant programs have been recently conducted at the SGS Lakefield site, sponsored by different clients. The main objective has been to develop a process flowsheet to generate a spodumene concentrate containing 6.0% or higher Li2O (~75% spodumene) suitable for producing lithium carbonate by a hydrometallurgical process. Depending on spodumene liberation size, dense media separation (DMS) can be an attractive option to produce a final high grade concentrate and to reduce the mass to be treated in the flotation circuit. In such a case, crushing would typically be performed in stages, with DMS separation to recover a spodumene concentrate and reject gangue minerals following each stage. DMS middlings and -0.5 mm fines can be processed by flotation to further recover spodumene. In the flotation process, coarse stage grinding minimizes the grinding cost and formation of slimes. In the majority of cases, a grind size (K80) of approximately 200 microns is sufficient for flotation. After primary grinding, mica, if present in an appreciable amount, should be floated to minimize interference with spodumene flotation. Desliming after scrubbing and high density conditioning are the key process operations prior to spodumene flotation. Spodumene can then be floated from silicate gangue minerals with a fatty acid or a mixture of fatty acid and petroleum sulfonate at slightly alkaline pH. Subsequently, feldspars can then be floated from the spodumene tailings."

Jan 1, 2012

By Michael I. Brittan, Craig M. Sams

"Economies of scale and the variable characteristics of many large ore deposits have resulted in grinding installations using very large SAG mills fitted with variable speed drives. Low-aspectratio single-stage SAG mills were introduced in South Africa to process the consistent gold bearing Witwatersrand quartzites. Elsewhere, circuits were patterned after the more conventional North American circuits with high-aspect-ratio SAG mills followed by ball mills. This paper provides information on two recent Gold Fields group installations covering both types of SAG mill in large, single-stage applications. While these operations process similar tonnages, the mills represent opposite ends of the aspect-ratio spectrum. The Tarkwa mine in Ghana employs a low-aspect 27’ x 42’ 14MW SAG mill. The St Ives mine in Australia operates a conventional 36’ x 18’ 13.4MW SAG mill.INTRODUCTIONGold Fields is one of the world’s largest gold producers with annual production of approximately 4.2 million ounces. The Gold Fields group has operations in South Africa, Ghana and Australia, along with numerous exploration sites and advanced projects in several other countries. This paper discusses new milling operations in Ghana and Australia.TarkwaThe Tarkwa Gold Mine is located in Ghana, West Africa, approximately 350 kilometers west of the capital city of Accra (Figures 1 and 2). The site conditions are tropical with an average annual rainfall of 1,930 mm and a maximum temperature of around 35°C."

Jan 1, 2006

By Patrick M. - Langevin

THIS TALK IS ABOUT : How the DBL mining camp deposits have been found and what is done to find the next one PLAN: Overview of the geological context Historical exploration perspective Deposits geology and key features Conclusion

May 1, 2006

Block caving is an underground mining method for the profitable extraction of massive, low-grade orebodies. Lately, it has become the mining method of choice, for many mining companies, because of depleted high-grade orebodies, and declining metal market prices. Block cave mining, however, still faces several challenges. Lack of access to the cave remains a major issue in understanding the rockmass response to mining for method optimisation. Improving our understanding of the rockmass response to caving will lead to safer and more productive operations. Combining large datasets from multiple sources with virtual reality scientific visualisation (VRSV) is a viable alternative to understanding complex cave behaviour without access to the cave. This is achieved using immersive environments with the ability to view complex multi-dimensional data (beyond 3D) graphically. VRSV offers a unique platform where it becomes possible to immerse the multi-disciplinary experts, and/or management team, in a virtual mine environment for quick decision making and fast resolution to conflicting conclusions. The underground mining system is complex due to multiple interrelating factors such as geology, excavation geometries, stress and time. Block caving is even more complex than most underground mining methods due to the network of tunnels required, and the use of induced stress, among others. As a consequence of the complexity in the block caving environment, it is vital that the mining system is analysed holistically, as a system, rather than optimizing individual factors one at a time. This paper presents a customised software module developed for use in the Advanced Visualisation Interactive Environment (AVIE) at The University of New South Wales (UNSW), Australia, to enable VRSV investigation into block cave mining systems (BCMS). This approach has the potential to provide a better understanding of the effect of time in in rock engineering, which has proven to be an important factor in hard rock mines (Ma & Daemen, 2006; Malan et al., 1997; Suorineni, 2010) but never validated. This work back analyses the early undercutting phase of a case study block caving operation with the view to understanding time/sequence effects. There is evidence that heterogeneous rockmass time-dependent behaviour governs the seismic response of the rockmass following undercut developments.

Jan 1, 2015

By V. J. Sopuck, O. P. Lavin, Ian Nichol

"A major challenge of contemporary exploration geochemistry is the development of procedures that can locate blind mineralization or mineralization that sub-crops below a cover of transported overburden, the composition of which bears no relation to the underlying mineralization. Over the past few years, the possible existence of diagnostic geochemical features in the country rock associated with volcanogenic massive sulphide deposits has attracted increasing attention both on the local mine scale and on the regional scale. In the present investigation, the nature of the geochemistry of a number of Archean greenstone belts of the Canadian Shield is examined to determine the feasibility of distinguishing productive from non-productive areas of copper-zinc mineralization. The results indicate that productive areas are distinguishable from non-productive areas providing consideration is given to the effects of igneous differentiation on rock compositionIntroductionArchean massive sulphide deposits are an important source of copper and zinc, and to a lesser extent silver and gold, particularly in Canada. As in the case of most other forms of mineralization, there is a continual need to develop new techniques that will improve the chances of success in the search for these deposits. The majority of Archean areas in the northern latitudes are overlain by a variable cover of glacial overburden. Considerable progress has been made in the development of new geochemical exploration techniques for use in glaciated terrain, based on the detection of anomalous dispersion in the glacial overburden. In certain situations, however, as in the search for blind deposits or in areas covered by glaciolacustrine deposits, overburden geochemistry offers little hope for success. In the case of massive sulphide deposits, one possible solution may lie in the detection of anomalous geochemical signatures in the bedrock. Recognizing this possibility, attention has been directed to the investigation of the nature of lithogeochemical dispersion associated with massive sulphide deposits on both regional and local scales, to establish the potential of lithogeochemistry as an aid in the search for these deposits."

Jan 1, 1980

By Derek Ettie

"In the Hydrometallurgical processes, the presence of the so-called "crud" is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design.The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the series-connected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation.The transfer of the organic phase into the electrolysis cell can result in a "burnout" of the cathode. The carryover of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show.To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl® by this means, we can guarantee our customers the maximum possible solvent recovery and minimize the solvent costs in this process step. This system is presented in detail in this paper."

Jan 1, 2014

By Mark Ferra

Flotation is used in mining to produce concentrates of copper, gold and several other valuable ores. In 2017, a copper mine near Globe, Arizona improved their rougher cells productivity using technically advanced electro-hydraulic actuators in the flotation process by enabling excellent tank pulp level process stability. The new actuators controlled the dart valve position to allow pulp to leave the cell. Tank cell pulp level can change due to feed and discharge fluctuations from neighboring tanks. When traditional pneumatic actuators are used, they have sluggish response times and overshoot due to the inherent physical property of air being compressible. Electro-hydraulic actuators have the benefit of hydraulic stiffness to deliver accurate and repeatable (0.1%) dart valve positioning. The froth layer has more opportunity time to maximize mass transfer into the launderer. The results are an increase in copper recovery by 2-4%. INTRODUCTION In 2013 there was an international flotation technical conference well attended by respected flotation specialists for both mining companies and academia. During the technical session a leading metallurgist was discussing pulp level measurement and said that when he was on the cell deck he stated, pneumatic actuators air cylinders stroking up and down. The presenter then claimed with confidence that "I listened to actuator move so the pulp level in the tank was being controlled!" No one questioned his assumption and I can assert that the audience was quite technical and not shy in their critiques of speakers. The flotation community simply believed that the existing pneumatic technology was enough with no alternative. Having a stable flotation cell pulp level is critical to effective copper recovery. Controlling pulp levels in flotation cells is a complex task that includes modulating dart valves in each cell. The use of REXA Electraulic actuators will decrease the process dead time and maintain froth height in a controlled manner, especially from pulp slurry volume fluctuations from neighboring cells. By reducing flotation cell pulp level tank height variation, a copper mine in Arizona has realized a 2-4% recovery improvement by increasing the froth transfer to the launderers in the rougher cell circuits compared to pneumatic actuators. This paper examines the benefits of using an electro-hydraulic actuator to ensure proper pulp level control and reduce the process operational cost. It will focus on actuator positioning the dart valves to maintain pulp level setpoint at a copper mine in Arizona.

Jan 1, 2019

By Maarten van de Vijfeijken, Marco Rufli

"By using the latest generation of medium voltage frequency converters, new possibilities have arisen to improve the grinding process. Beside all the direct and indirect advantages, several dedicated functions have now been implemented for ring geared grinding mills in the minerals industry. The advanced operational functions ensure a smooth, safe and reliable operation with minimum stress for the mechanical equipment and therefore highest availability of the mill. Several papers have already been presented concerning the benefits of using this state of the art technology for mill drives (Ravani von Ow and Bomvisinho, 2010; Ravani von Ow and Gerhard, 2010). However this paper will not only show and explain the operational benefit of these functions, but will focus on the experiences gained with this kind of sophisticated ring geared mill drive system. Several measurements of different operating conditions (starting, frozen charge remover, controlled roll back, backlash, etc.) made on an installed and commissioned 2 x 5 MW dual pinion ring geared mill drive system will be shown and discussed. Also the accuracy of the load sharing between the two 5 MW motors during starting, normal operation and stopping will be demonstrated using real measurements from an operating system. Finally the inherent features of these drive systems are briefly discussed.INTRODUCTIONLooking at the demands of grinding mills, we can split them into operational, maintenance and protective demands. For smooth and safe operation, it is important that critical situations are avoided as much as possible. Maintenance functionality must be quick and easy to execute, while protection of the system is important during all operating conditions. ABB has considered all these demands during development of their dedicated mill functions. By adding an additional controller (mill controller), not only a lot of application related functionality and protection is included, but also the interface between the mill drive system and the customer’s distributed control system (DCS) is simplified."

Jan 1, 2011

By Nicolae Dobritoiu

The literature in this field and the practical activity record that a method, respectively the technology used for an underground mining work have many components which, in order to be applied, demand that for each of the parameters that describe the environment of the mining work and that influence the chosing of that method and that technology of execution, must have values in an interval well determined. There are situations when one or many parameters of the set of parameters that describe the environment of the mining work, can modify its values, and, as a result, one or more components of the methods or technology cannot be applied anymore, making necessary a replacement of their values. The information offered by this graphical-analytical model allow the determination of optimum solutions for the process of digging of the underground mining work and thus it will result the incresing of the technical-economical efficiency of the digging process and, also the increasing of the quality of the underground mining work.

Oct 1, 2009

By Huilan Yang, Feng He

This paper intends to introduce the development of copper smelting and converting technologies in China in recent years, with a particular emphasis on the introduction of various continuous converting technologies, and moreover, it analyzes the advantages and disadvantages of those technologies, including their impact on the downstream anode refining from different points of view. INTRODUCTION At present, many converting technologies are used in copper pyro-metallurgical plants in China, including Peirce-Smith (PS) converter, flash converting furnace, multi-lance based top blowing, bottom blowing and so on. These technologies have spanned a wide range of time. PS converter technology has been applied in copper smelters for many years and most of the blister copper have been produced by this technology; flash converting technology has been developed since 1990s and been maturely applied in several plants up until now; top blowing and bottom blowing technologies have been revived in China in the past decade and boast good environmental protection performance, energy efficiency, throughput capacity and short process flow. All of the said technologies have reference operations in treating high-grade matte. As more and more attention is paid to environmental protection globally and copper smelters continuously seek for cost reduction, it is necessary to share those converting technologies, especially those new converting technologies derived in China, with copper smelting practitioners in the world. This paper aims to analyze the advantages and disadvantages of various technologies from a macroscopic view and discuss their actual application effects, current developments and future improvements. BRIEF INTRODUCTION OF VARIOUS CONVERTING TECHNOLOGIES IN CHINA China has seen a rapid development in copper smelting industry in the past 30 years and has become the largest gathering place of copper smelters in the world, most of which are operating with PS converting furnace technology, however, with the increasingly strict environmental requirements of the Chinese government in recent years, the low-level pollution issue and the disadvantage of large gas exhaust amount per unit of copper of converting furnaces are particularly prominent.

Jan 1, 2019

By D. M. May

"Cut-and-fill mining is a stoping method that has been widely utilized in the mining industry over the past forty years. It took preference over shrinkage methods at Levack in the early 1930sbecause of its safety aspects; i.e., prompt support of the stope sidewalls, good working floors and better accessibility to support poor back areas. In addition, higher recoveries of ore were possible because of the flexibility of the method in that silling could take place easily at any horizon; low-grade ore could be sorted and left in the stope as fill and certain zones of rock could be left unmined. With modern techniques, a steady production rate can be established, as filling and mining can be carried out stimultaneously.AIthough there are numerous variations of cut-and-fill mining throughout the world, this paper reviews the original type of mining, with modifications and improvements through the years to present modern practices, with the Levack West operation appearing to be the most productive at this time. Stoping efficiencies have also increased substantially from the original 10 tons per manshift to the present 55 tons per manshift.The paper also outlines the many improvements that have been made with respect to mucking and ground support operations; from hand mucking in a single stope to the use of frontend loaders and haulage trucks in fully accessible stope complexes; and from timber props to roof bolts of various types. Although present methods are extremely satisfactory, experimentation is continually being conducted to improve safety and productivity for future mining.IntroductionThe major mining operations of the Ontario Division of Inco Limited are located in the Sudbury Basin (Fig. 1). Around the rim of this geological formation and within 30 miles of the City of Sudbury are nine producing mines and one ' open pit operated by the company .Ore production currently approximates 11.5 million tons per annum from underground and open-pit operations. Underground mining methods include sub-level caving, shrinkage, cut and fill, undercut and fill, blasthole and vertical retreat. The Levack Complex, the main plant of which is the central Levack Mine, produces 11,000 tons per day.The first prospecting in the Levack area, in 1887, was conducted by James Stobie, who examined rock cuts along the route of the Canadian Pacific Railway to the northwest of Sudbury. However, it wasn't until 1913 that operations commenced at Levack under the Mond Nickel Company."

Jan 1, 1981

By Mostafa Benzaazoua

Les remblais en pâte cimentés sont de plus en plus utilisés dans les exploitations minières souterraines. Une autre alternative d?utilisation du remblai en pâte consiste à le pomper et à le stocker dans des empilements de surface. En plus d?avoir des avantages d?un point de vue de stabilité physique des ouvrages, le remblai en pâte cimenté en surface permettrait également de stabiliser les contaminants dans la matrice du remblai à l?aide du processus de solidification et de stabilisation. Dans cette étude, des remblais en pâte constitués d?un résidu minier sulfuré renfermant beaucoup d?arsenic et de différents liants ont été testés afin d?évaluer la stabilisation des contaminants dans la matrice de remblai. La méthode utilisée pour évaluer la stabilisation et la solidification des contaminants est le test de lixiviation en extracteur de Soxhlet. Les résultats géochimiques issus de ces essais ainsi que la caractérisation chimico-minéralogique des remblais lixiviés ont été analysés pour comprendre les phénomènes chimiques présents dans les remblais durant le temps de cure. Les résultats obtenus montrent que les sulfures présents dans les remblais étudiés (pyrite FeS2 et arsénopyrite FeAsS) s?oxydent et provoquent la dissolution des hydrates les plus vulnérables (dissolution de la portlandite Ca(OH)2 et/ou décalcification des gels CSH). Le calcium produit permet de précipiter les sulfates (essentiellement sous forme de gypse plus ou moins hydraté) et l?arsenic sous forme d?arséniates de calcium plus stables. Les différents liants utilisés donnent des résultats différents en termes de stabilisation et de solidification qui seront discutés dans cet article.

Nov 1, 2002

By Dominic Fragomeni

"The mineral processing industry has had a long history of innovation that is recognized but not often celebrated. These include significant advances in mineral measurement, testing, comminution, mineral separation and process control technologies that have transformed mineral assemblages into ore.This presentation presents some of the major mineral processing innovations and the impact they have had on our industry. As we look to the future, it is critical that we innovate and change. We will explore some examples of the next developments and how they can be catalyzed in the face of risk management, lower metal price cycles, resource constraints, inertia and the challenge of short term value delivery."

Jan 1, 2017

By Frederic M. Langevin

?? Introduction ?? LaRonde ?? History of Seismicity and Rockbursting ?? November 27th 2002 Rockburst ?? April 1st 2006 Rockburst ?? December 11th 2006 & January 11th 2007 Rockbursts ?? Seismic Risk Management Plan ?? Conclusions ?? Located in Northwestern Quebec (Can.) ?? In operation since 1988 ?? Reserves at Shafts #1 and #2 depleted ?? Production now comes entirely from Penna Shaft ?? Deepest single-lift shaft in the western hemisphere (2240 metres) ?? 7300+ tonnes per day ?? 2007 Reserves (proven & probable): ?? By-products: Ag, Cu, Zn ?? Sinking #4 Shaft (LaRonde II winze)

Feb 1, 2008

By P. G. Semple

"In January 1985, Equity Silver Mines Limited began operation of a cyanidation circuit to scavenge precious metals from the flotation tailings. At present, this process is treating 270,000 tonnes of tailings per month and is recovering in excess of 0.20 grams of gold per tonne. To obtain these results Equity is operating a carbon-in-leach circuit that utilizes pressure stripping, zinc precipitation acid washing and thermal reactivation. A cyanide destruction circuit is also required to minimize the deleterious effects on reclaim water in the flotation stage. This paper describes the existing scavenger plant, and details the start-up problems encountered and the modifications made to correct these problems.INTRODUCTIONEquity Silver Mines Limited , a 68% owned subsidiary of Placer Development Limited , is located 38 km southeast of Houston in north central British Columbia. The geographic location of Equity Silver Mines is shown in figure #1. In September 1980, production first began with the ore being supplied from the Southern Tail open pit. In March 1984, the Southern Tail deposit had reached its economic pit depth, and since then ore has been supplied by the Main Zone pit the gold mineralization in the Main Zone is less refractory than the Southern Tail and cyanidation of the flotation tailing appeared to be a viable alternative.An extensive test program was undertaken and the results confirmed that considerable gold and silver values were amenable to cyanide leaching. A feasibility study showed that these values could be economically recovered and the detailed engineering work began."

Jan 1, 1987

By M. N. Bassim, W. W. Tennese

"Concepts of linear elastic fracture mechanics were applied to study two cases of failure, namely an equalizing beam from a tandem rear axle of a highway tractor unit and the main beam of a flat bed trailer. In the first case, the presence of a crack, initiated by stress corrosion cracking followed by significant fatigue crack propagation produced a state of stress which was sufficient to produce brittle failure. Calculation of the fatigue life agreed with the number of cycles that the structure experienced before final fracture. In the second case, it was demonstrated that a combination of low temperature and high loading rate was sufficient to cause brittle fracture.IntroductionFailure analysis of engineering components has generally been carried out without the benefit of fracture mechanics. It is generally understood that real structures inevitably contain internal or surface flaws which under an applied load, may propagate to fracture. Fracture mechanics relates the applied stresses to the crack size in specified geometries. Since its introduction approximately thirty years ago, fracture mechanics has evolved as a design philosophy which can be used to develop fracture-safe designs. It can be also applied in analysis of failures, to ascertain if sound design and fabrication methods have been used."

Jan 1, 1985

By M. H. B. Nasseri

Barre granite?s samples have been tested for fracture toughness under mode I along two different directions with respect to microstructural fabrics were investigated. 3D objects counter algorithm technique is applied on micro CT images to identify physical properties such as crack induced porosity, crack density, generated total surface area and contribution of individual mineral grains within the damaged zone.The result obtained justifies very well the fracture toughness anisotropy in Barre granite, and explains the difference in the structure of the damage zone evolving as a result of test crack interacting with pre-existing microstructural fabrics. The present study has potential application in the fields of rock mass stability, oil reservoir stimulation, rock fragmentation and damage in blasting and emplacement of dykes.

May 1, 2009