Search Documents

By A. Gronningsater

Introduction As is well known, the fight between the blast furnace and the reverberatory furnace in copper smelting during the second decade of the century ended with a victory for the latter, a result which must largely be attributed to the introduction of flotation methods. To my knowledge, no new blast furnace has been blown-in at any American copper smelter since the War. As the metallurgy of nickel, up to and including matte smelting, is generally considered a close parallel to that of copper, the introduction of reverberatory smelting in the big new smelter of the International Nickel Company at Copper Cliff, built in 1928-30, seemed a logical adherence to a well established trend. In view of these facts, considerable comment was made when Falconbridge Nickel Mines decided to retain the blast furnace in their smelter built about the same time, in 1929. A presentation of the reasons governing this choice should therefore be of interest. The basic principles underlying the Falconbridge practice, and the considerations guiding the successive steps in the operations, will be discussed in the following. To understand the problems involved, the character and mode of occurrence of Sudbury ore must be kept in mind. Large amounts of disseminated ore are generally present. Although the gangue usually runs only about 50 per cent Si02, the ore hoisted as a rule contains more silica than needed in the smelting operation; until recently this excess was removed entirely by hand picking (in later years supplemented by magnetic sorting methods), a difficult and not very satisfactory method, in which 'the border line between ore and waste is entirely arbitrary, and therefore too much depends on the judgment of the picker.

Jan 1, 1934

By Silvana Costa

In the last two decades, there have been nearly no new mining towns built in Canada. Governments and mining companies have viewed long distance commuting (LDC), commonly known as fly-in-flyout or fly-in mines, as a way to avoid problems associated with building a new community and providing for its sustainability after mine closure. LDC is also considered more cost-effective than building a mine town. The intensification of the use of LDC in the Canadian mining sector has been quite rapid, particularly in northern regions. However, LDC has implications to employees, their families and communities, which deserve further examination, particularly considering the significant expansion in Northern mining and Aboriginal participation in this sector. This paper presents a review of the major issues in long distance commuting, both from an industry and community perspectives. It is a result of preliminary investigation for a PhD research project that will be pursued by a Bridge Fellow and UBC Mining Sustainability Working Group member, and guided by an interdisciplinary research team at the University of British Columbia (UBC). The Bridge Fellowship Program is research-training program linking the UBC?s Faculties of Medicine, Engineering and Graduate Studies. Its mission is to develop creative evidence-based prevention measures for public, environmental and occupational health problems. The SWG is an interdisciplinary student group based in the UBC Department of Mining Engineering, committed to respond to the complex sustainability-related challenges currently faced by the mining industry. In other to pursue this project, it is paramount that industry and local communities alike participate in the development and clarification of research questions as well as in the research design. It is hoped that this paper will function as an invitation for industrial and community partners for such study. The main themes identified for this research are occupational health and safety of LDC employees, family life impacts and community health impacts of this model of resource development.

May 1, 2004

By H. S. Price, F. N. Kissell, R. C. McCulloch, J. C. Edwards

"The methane em1ss10n from deep coalbeds which are actively mined is a serious problem facing the mining industry today. Pinpointing the source of methane and predicting the emission of this gas from these coalbeds is necessary if preventive techniques are to be effectively used to control methane emission. In general, because most coalbeds have water associated with them, the system to be studied may be either single-phase (methane gas) or two-phase (methane and water). Because coal mine geometry is complex and the fluids have variable properties as functions of pressure and methane concentration, the differential equations describing the flow of methane and water are not amenable to analytic solution, but must be solved numerically using high-speed computers. This paper presents the development of such a complex mathematical model along with some preliminary applications of the model to methane emission from one- and two-dimensional coalbeds with and without water present."

Jan 1, 1973

By F. McCarthy, W. Zhang, R. McDonald

"The processing of nickel laterites has been a topic of major interest at CSIRO for almost twenty years. During this period CSIRO has collaborated with other researchers and industry in developing a better understanding of existing processes and been actively involved in testing/developing new beneficiation and process options for these ores. The current paper summarises the results of selected studies and highlights improvements that have been achieved. Key topics to be discussed include enhancements in the mineralogical characterisation, beneficiation approaches, improvements in the understanding and application of leaching technologies, the development of synergistic solvent extraction (SSX) for the recovery of nickel/cobalt from laterite leach liquors and the collaborative development of the Direct Nickel process. Future opportunities and key research questions will be briefly examined.INTRODUCTION Nickel laterite ores comprise a significant resource in Australia and according to United States Geological Survey data nearly a quarter of world reserves are located there (USGS, 2016). More specifically, around 95% of Australian nickel resources (laterite and sulfide) are located in Western Australia (Australian Government, 2017). Given the recent closure of Queensland Nickel, essentially all of Australian nickel production occurs in Western Australia and the primary producers of processed nickel products include Nickel West (Kwinana) with ~84,000 t saleable nickel metal in 2016 (BHP Billiton, 2017), Minara Resources (Murrin Murrin) with 46,700 t nickel metal produced in 2015 (Glencore Australia, 2017), and First Quantum Minerals Ltd (Ravensthorpe) who sold 25,882 t nickel as mixed hydroxide product in 2016 (First Quantum Minerals, 2017). The total sales of nickel from Western Australia in the 2015-16 financial year were 175,722 t. The study of nickel laterites at CSIRO recommenced at the time second generation High Pressure Acid Leaching (HPAL) plants were being commissioned at Bulong, Cawse and Murrin Murrin in the late 1990’s. A combination of technical and engineering issues meant that the ramp-up times at these operations were slower than expected and the outcomes resulting from the attendant problems are well documented (e.g. Griffin & Becker, 2000; Reid & Barnett, 2002; O’Callaghan, 2003) while the issues faced at the BHP-Billiton-built Ravensthorpe plant have been addressed by the current owners of this project, First Quantum Minerals Ltd (Piper, 2012)."

Jan 1, 2017

By W. E. Uren

The Dominion Coal Board was created by Statute passed on July 17th, 1947, and was brought into effect by proclamation on October 21st, 1947. It is, consequently, a comparatively young body, having been in existence for only eighteen months. Before dealing with the constitution and duties of the Board, it may be well to answer the unspoken question of why it has been considered necessary to single out coal as one specific mineral requiring the continuous attention of a specially created permanent Board. In Canada, coal has been the neglected sister of the more spectacular minerals and it comes as a surprise co many to note that in 1948 the value of the coal produced in Canada was higher than that of any other mineral with the one exception of gold. Coal touches upon our daily lives in many different places of which the public are not generally conscious. As household fuel, it is a necessity of life in this northern climate; as a source of steam, it provides the heat for most of our industries; it is the food of the 'iron horse' chat shuttles our persons and our goods across the land; it is the source of power in many parts of the country; it is the chemical reducing agent chat, in our furnaces, transmutes the metallic oxides to the virgin metal. Coal is, in fact, the indispensable mineral chat forms the corner-stone of our present structure of industrial civilization. Is it, then, such an odd thing that the provision of an adequate supply of coal should be a matter of national interest or that measures should have been taken by government co provide for a constant watch, by a permanent Board, on the supply of co al? ? The Board is the result of the recommendations of the Royal Commission on coal which made a long and detailed study of the Canadian coal problem. It is composed of a permanent Chairman and six part-time members, most of whom have had intimate contact with various phases of the industry.

Jan 1, 1949

By M. B. Dusseault, A. Pirayehgar

"There is concern that hydraulic fracturing (HF) near an existing critically stressed fault could trigger slip and generate a seismic event of significance. To this end, a mathematical discontinuum model representing a naturally fractured rock (NFR) mass containing a fault is created, and fault slip response to fluid injection is studied. UDECTM is used as a Discrete Element Method (DEM) approach to define the seismic moment, and also to assess the influence of injection and slip on further shear slip propagation. In most of the simulations, slip and dilation take place along a number of oriented fracture surfaces, so it is reasonable to assume that in a real case, microseimic emissions would accompany each slip “event”. The moment magnitude scale (Mw) is used to measure the size of the microseismic event in terms of the energy released. Seismic moment is a measure of the total energy (work) released during a seismic event and is used to measure its size. From another aspect, the injection energy is calculated as the total energy required for achieving the hydraulic fracturing; this is viewed as energy to open fractures against the ambient stress field and much of it is potential stored energy that can be released and create discontinuities (work of fracture), deformations (W=F·d), heat and radiated seismic energy. A small amount of the total released energy is transformed to radiated seismic energy and another small amount results in tensile fractures. Fracture energy is used to calculate the work required to create fracture surfaces. Comparing the energy release by fracturing or seismic events indicates their contribution to the total amount of released energy or total work. The amount of energy associated with the stick-slip event is small compared with the overall work done to generate the distortions (i.e. increases in aperture by forcing them open) in the rock mass, and much of the energy in slip is lost as heat from the plastic deformation, rather than as radiated seismic energy.Microseismic monitoring shows the spatial distribution and magnitude of seismicity associated with slip of bedding planes and natural and incipient fractures. Work calculations have been undertaken to look at the various sources of energy storage (elastic strain energy) or dissipation (slip), and likely the energy losses from viscous dissipation could be addressed as well, helping to clarify HF processes in NFRs."

Jan 1, 2015

By M. B. McClenaghan, O. P. Lavin, Ian Nichol

"Abstract-Exploration in most areas of Canada has to contend with problems posed by glacial overburden. In many areas exploration for gold has been based on the sampling of tills, frequently by deep overburden drilling, and analyses of heavy mineral concentrates. Notwithstanding the significant role that till geochemistry has played in the discovery of some important gold deposits over the last few years, increased appreciation of the nature of the glacial history and stratigraphy and the character of gold within till has led to the recognition of a number of ways whereby the effectiveness of exploration can be improved upon.In order for till geochemistry to be useful in exploration, a number of conditions must be fulfilled, including:1. mineralization, or alteration halo related to mineralization, subcropping at the bedrock /over­ burden interface; 2.glacial erosion and dispersal of a recognizable signature of mineralization into the glacialsediments; 3, preservation of glacial sediments containing this geochemical component (trace metal or mineral) at positions subsequently selected for sampling (normally drill sites); 4. correct identification of specific till units and associated ice movement history; 5. collection of adequately large and representative samples; 6. appropriate sample preparation and processing; 7, appropriate geochemical analyses; and 8. correct data processing and interpretation.While we have no control over the first two geological conditions, and only limited controlover till availability, we can control the quality and thoroughness of sampling, sample identification, sample preparation, analysis and interpretation. In particular attention needs to be focussed on obtaining a large enough sample to be adequately representative, an unbiased sample must be collected, together with appropriate sample processing, analysis, data processing and interpretation. It is considered that by modifying or extending existing approaches to gold exploration the chances of exploration success can be increased. In particular, analyses of both the heavy mineral and minus 63 ?m fractions of till is recommended because gold in till may occur in different size fractions."

Jan 1, 1992

By T S. Cochrane

This paper is based on observations made during a recent visit by the writer to three of the dust research laboratories .in West Germany, each .of which is mainly concerned with studymg the composition and character of the respirable dust produced in mines or at industrial sites. The three institutes are discussed as regards their orgamzat10n and duties, their methods of dust sampling and analysis, and recent trends in research and development. An extensive bibliography completes the paper. Introduction A RECENT trip to Europe to attend international conferences m Austria and m Belgium gave the writer the opportunity to visit a number of research laboratories and mines in Western Europe. The visits to the dust research laboratories in West Germany are the basis of this report. In Germany, cooperative associations formed prior to and since the turn of the 20th Century to promote the safety and welfare of their workers have recognized the effects of airborne dust on the general health of the labour force.

Jan 1, 1964

By J. Visman

"The Compound Water Cyclone is a concentrator for the wet processing, in bulk, of finely divided materials such as slack coal, fine ores and mineral sands. It was originally developed by the Fuels and Mining Practice Division of the Mines Branch, Department of Mmes and Technical Surveys, Ottawa, for the cleaning of friable slack coals and slurries.Since its introduction in the coal industry in 1962, its application to other materials has also been studied, with special emphasis on simplicity of operation and low over-all cost per ton of finished product .In this paper, a description is given of commercial two-stage units presently available for the processing of granular materials, including wastes a1:1d other low-grade products. A pneumatic control system is used for operating the cyclone under back pressure .and for automatic cut-point adjustment. An account is given of results obtained on coal mineral sands and ores in the Wes tern Regional Laboratory of the Department of Mines and Technical Surveys. Results of several industrial applications are discussed."

Jan 1, 1966

By G. P. Contractor

Medium and low carbon steels, modified with uranium, were studied in order to evaluate the influence of uranium on forge ability, mechanical 11roperties, response to heat treatment and microstructure. Uranium contents ranged up to 0.70 per cent. The medium carbon steels are hot short if the uranium content exceeds about 0.35 per cent. More uranium can be tolerated in low carbon steels. The hot shortness is caused by the formation of intergranular phase UFe2. Critical transformation temperatures, Jominy hardenability, and resistance to tempering are not significantly affected by the 11resence of uranium. Similarly, uranium has little or no effect on the tensile properties of carbon steels. The addition of uranium has a favourable effect 11n the stress-rupture characteristics and some beneficial effect on fatigue properties. However, more results are required for verification. In the steels investigated, it seems that most of the uranium carbide combines to form complex inclusions of U (0, C, N) or (C, N), rich in oxygen or nitrogen or both.

Jan 1, 1963

By Jin Liu, Torstein A. Utigard

At its Copper Cliff Smelter, Vale Inco Limited processes a bulk copper-nickel concentrate in two Inco oxygen flash furnaces. Coke supplies a minor proportion of the process heat requirements, limiting the flash furnace matte grade to the target 45% CuNiCo. Coke addition to the furnace offers a potential means of establishing a reducing barrier on the surface of the molten bath. Such a practice would be conducive to producing sulfur deficient (partially metallized) matte. At the same iron content, the iron activity of sulfur deficient matte is higher than that of regular matte. A supernatant coke barrier could, therefore, be expected to lead to higher nickel and cobalt recoveries, reduction or even elimination of magnetite furnace bottom build-up and increased sulfur elimination as SO2 in the flash furnace. Extensive experiments were conducted in a miniplant flash furnace to investigate the effect on process metallurgy of the suggested modified scheme. The introduction and description of the experimental set up were given in Part 1 of this paper and an early paper published in Yazawa symposium1 together with the results and some in depth discussion on metallurgy. This paper intends to discuss the kinetics of the miniplant flash furnace testwork.

Jan 1, 2015

By J. C. Underwood

"The wear performance of grinding balls under conditions of impact and abrasion is affected by their chemical composition and structure. The selection of appropriate analyses and heat treatments that will provide both abrasion and impact resistance takes into account the effects of certain elements on structure and harden-ability, as well as the over-all effect of composition and hardness penetration on the residual stress pattern developed through heat treatment. Direct quenching from forging temperatures substantially increases hardenability over that obtained in reheat-quench practices, and can be done without undue risk of damage to the ball provided that the harden-ability bears the correct relationship to ball diameter.Average volumetric hardness and percent hardened volume are convenient parameters for quantitatively expressing the response to heat treatment and indicating anticipated wear properties. A number of factors which can lead to reduced wear life as a result of material or processing problems are reviewed and illustrated."

Jan 1, 1959

By Yongjun Peng, Yufan Mu, Rolf A. Lauten

"Chalcopyrite, a major source of copper, is commonly found associated with iron sulfides, particularly pyrite. The separation of chalcopyrite and pyrite by flotation is difficult due to the galvanic interactions between pyrite and chalcopyrite during grinding and flotation. Galvanic interactions may cause oxidation and dissolution of chalcopyrite, copper activation of pyrite and the formation of hydrophilic iron hydroxide coating. The overall effect may change the floatability of the components and lead to the misplacement of pyrite into chalcopyrite concentrate. The objective of this study was to investigate the effect of lignosulfonate-based biopolymers on the depression of pyrite in the flotation of chalcopyrite with xanthate as collector and the mechanism responsible for the selective depression of pyrite. The flotation results showed that biopolymers depressed the flotation of both copper-activated pyrite and chalcopyrite in single mineral flotation although to different extents. In the flotation of mixed mineral systems, biopolymers significantly depressed pyrite flotation but had a less influence on chalcopyrite flotation. The selective depression of pyrite by biopolymers was due to the preferential adsorption of biopolymers on copper-activated pyrite surface. Galvanic interactions between pyrite and chalcopyrite surfaces promoted copper activation on pyrite. Presence of cuprous ions on pyrite surface favored biopolymer adsorption by the formation of a complex between the cuprous ions and biopolymer molecules. The same galvanic interactions also facilitated chalcopyrite oxidation leading to the formation of hydrophobic polysulfide that enhanced the hydrophobicity on chalcopyrite surface. The biopolymer structure controlled the depression effect. The results showed that the biodegradable biopolymers are promising depressants for pyrite.INTRODUCTIONCopper sulfide minerals, such as chalcopyrite (CuFeS2), bornite (Cu5FeS4), chalcocite (Cu2S) and covellite (CuS), are the major mineral source for copper. They are often found finely interlocked with iron sulfides, especially pyrite (FeS2) (Owusu, Brito e Abreu, Skinner, Addai-Mensah, & Zanin, 2014). Pyrite, as the most abundant sulfide mineral, is perceived as gangue in most cases and should be removed from the associated sulfides to minimize its contamination of the copper concentrate (Owusu, Addai-Mensah, Fornasiero, & Zanin, 2013; Wang & Forssberg, 1991). The commonly used strategy to remove pyrite is flotation (Wang & Forssberg, 1991)."

Jan 1, 2016

By W. A. Haley

This paper discusses how a large wheel loader should be equipped, with particular attention paid to tires and tread life, and describes the several steps that can be taken to provide favorable working conditions and reduce over-all costs. A comparison is then made of wheel loader production and costs vs those of power shovels, and the present and possible future applications of the wheel loader are outlined.

Jan 1, 1969

By D. J. Hains

IN this paper we shall examine the Why, Where and How concerning the agglomeration of iron ores and concentrates. Fig. l answers the questions @f why there is so much interest at the present time in the art of agglomeration. The use of sinter or pellets in the blast furnace has materially increased their rated •capacity. ':'President Hains Company Ltd. Engineering J. S. McMahon ( 1) reports an increase from 653 tons of .pig iron per day to 1140 tons of pig iron per day with the use of a 100 per cent sinter burden on one of his blast furnaces. In the United States the use of 100 per cent pellets has increased pig iron production from approximately 1800 tons per day to over 3000 tons pig iron per day (2). In our economic system the general objective is to produce more and better commodities cheaper. Fig. 2 shows the decrease in coke consumption with increased tonnages from the furnaces when using -

Jan 1, 1961

By J. B. McKay

It is the purpose of this paper to present an initial report on the construction and operation of the Fluo-Solid roaster at the property of Campbell Red Lake Mines, Ltd., Balmertown, Ontario. The roaster prepares for subsequent cyanidation the bulk flotation concentrate obtained from four hundred tons per day of gold ore. The mill flow-sheet 'includes jigging and amalgamation; flotation; cyanidation of flotation tailing; and roasting followed by cyanidaition of flotation concentrate plus amalgamation tailing. Overall mill recovery for the year 1950 was 90.2 per cent. Recovery possible by straight cyanidation of this ore would not exceed 80 per cent. The ore contains considerable arsenopyrite and pyrrhotite as well as pyrite, with lesser quantities of nickel, zinc, and copper minerals. The mineralization is for the most part extremely fine. The roaster first went into operation on August 7th, 1949, and at the end of 1950 it had roasted 10,916 tons of concentrate. The average recovery of gold from calcine during that period was 94.86 per cent in the primary stage of calcine cyanidation. The average assay of calcine residue from primary cyanidation for the entire period was 0.37 oz. per ton. Both laboratory tests and plant metallurgical balance calculations indicate a further recovery of approximately 10 per cent of this 0.37 oz. when the calcine residue is again cyanided, in the flotation tailing cyanidation circuit.

Jan 1, 1951

By K. Winterton, Carruthers. J.

"Attempts have been made to produce hardened structures of a pseudomorphic type in various carbon and alloy steels. In order to obtain martensite with a fine distribution of cementite, an initial structure of fine lamellar or nodular pearlite is required; this may be obtained by conventional means. This is followed by partial austenitization and quenching.Two methods have been tried to induce partial austenitization:(a) A resistance (direct current) heating method involving rapid entry into the austenite field.(b) A new method, described as the ""threshold"" technique, involving homogenization of temperature just below A 1, followed by entry into the austenite field; two furnaces are required.The resulting structures have been examined for microstructures, hardness, tensile, and impact values. The tensile properties are comparable with those obtainable by conventional treatment methods. Impact values are disappointing, but this is explainable from the nature of the manifold changes occurring."

Jan 1, 1960

By M. F. Almeida

"Due to the randomness of all factors influencing the sintering operation, a two-stepped procedure is proposed to find the best way of using stocked fines at a plant producing Fe-Mn alloys for the steelmaking industry. The approach is based on the following: (1) predict the result of the sintering operation by establishing the best multilinear regression model using some of the characteristics of the loaded material; and (2) find the best solution under a minimizing cost criteria by solving a linear optimization problem using the regression equation plus constraints on the feed and product. IntroductionSome tests carried out using 20% to 30% of sinter in the material loaded into a 60 000 KVA Tysland-Hole electric furnace producing Fe-Mn alloys for the steelmaking industry indicated: (1) a meaningful decrease in the off-gas temperature and, consequently, a better energy use due to the material higher porosity; (2) more uniform heat distribution as a consequence of the electrode reaction zone enlargement; (3) an improved furnace control resulting in a smoother operation; and (4) a decrease in gas production facilitating the off-gas treatment. For some years, this plant used only the coarse fraction of the Mn ores, thus stocking all the received and own-generated fine particles. In view of the mentioned results, a strategy for increasing the use of stocked fines was formulated, including a step where it was necessary to decide which components and respective quantities should be used in the blends to be sintered (Almeida, 1984).It is well known that several factors affect productivity and energy consumption in sinter production, also influencing the product quality. Raw materials characteristics, namely chemical and size composition, affect permeability to gases and may or may not allow a deeper bed. In general, finer ores decrease permeability, increasing electricity consumption by fans, but due to their higher specific surface area, react more completely with other components in the mixture. For coke granulometry, a compromise must be obtained in order not to burn it too quickly nor to widen the flame front, therefore decreasing productivity. Decreasing coke in the blend also acts in sinter bonding, decreasing its consistency and increasing crushing and return fines. Moisture addition also influences components mixing, pre-agglomeration, bed permeability and, consequently, sintering productivity. Therefore, optimum conditions must be established for both a given sintering plant and the components in the feed (Dawson, 1993)."

Jan 1, 1998

By D. D. Liu

This paper proposes a charge induction dust measurement method based on detrended fluctuation analysis (DFA) for use in coal mine environments, based upon electrostatic interference, dust properties, wind speed, particle size, moisture content and other factors. In this methods, sequence x(t) is first obtained through a dust concentration sensing probe, and then the cumulative deviation y(t) is calculated, and y(t) is divided into same lengths. Secondly, a first-order linear fit is used for data of each interval, and mean-square deviation filtered DFA was calculated for each interval. Finally, the dust mass concentration of the corresponding time is obtain by supplemented calibration coefficient and fitted the data point which is the mean and square root for all lengths of interval. Simulation and verification experiments showed that the charge induction dust measurement method based on DFA can reduce coal mine electrostatic interference effects with high accuracy. The design has been successfully applied to select areas.

Aug 1, 2013

By P. Talonen

Since the last Iron Control in Hydrometallurgy Symposium in Montreal in 1996, the Kokkola zinc plant has increased its capacity from 175,000 t/y to 280,000 t/y by installing an atmospheric concentrate leaching process, which has also affected iron control in the leaching circuit. Major changes have been made at the jarosite residue pond; a subterranean plastic wall reinforced with bentonite and cement has been built around the pond. A new water collecting system that is used for groundwater level control in the pond area was installed. With these two investments in the pond area, it is now possible to prevent any seepage flow from the pond into the surrounding environment. Water pumped from the residue pond is treated in the water treatment plant. This paper describes the behavior of iron in Kokkola's current leaching processes. The treatment of the jarosite, the improvements to the residue pond and the water treatment process are also described.

Jan 1, 2006