Search Documents

By Leggate J

In the past many coal mining projects commenced without any consideration being given to eventual site rehabilitation. Now that site rehabilitation is assuming greater importance with changing community expectations, and standards are becoming less negotiable, it cannot be ignored in either the development of mine working plans or economic models. The "unspecified" rehabilitation measures associated with many existing projects will be the subject of debate for some time to come yet. It would be wise to plan for the future. Once an agreeed standard of rehabilitation is accepted, good management involves considering practices which will facilitate eventual rehabilitation at least cost. Without planning for rehabilitation, many mines have adopted practices which are likely to result in very expensive rehabilitation measures and impact significantly on the overall profitability of the ventures. With adequate planning, procedures can be developed which achieve the same short term goals without significantly effecting cash flow but with very significant impacts on the final rehabilitation cost. This paper looks at the disposal of tailings and overburden in the coal mining process. The industry has in the past had an obvious preference for the "perceived" cheaper procedures for waste management such as wet disposal of tailings and high dumping of overburden. There are alternatives. The paper discusses the principles which should be incorporated into tailings and overburden disposal systems and identifies viable alternatives.

Jan 1, 1991

The main factors controlling the electro- winning of zinc from impure aqueous sulphate electrolytes are reviewed. Zinc, hydrogen and impurities are deposited at the cathode. The current effic- iency for zinc is increased by increasing zinc/ acid ratio and current density and by decreas- ing temperature; and may be unchanged, increased or decreased by the presence of impurity ions. A qualitative comparison of observed and predicted impurity effects is in reasonable agreement. Quantitative treatment of the effects of impurities and cell additives is not available. A tentative explanation of the time dependence of current efficiency in the presence of some impurities is provided. The forms in which impurities are deposited is substantially unknown. Impurities may be classified according to the extent of cathodic deposition. Procedures for control of cathodic deposition of impurities are outlined. The main anodic reactions are the forma- tion of oxygen, manganese dioxide and sulphuric acid. Minor reactions include the oxidation of lead, silver, cobalt and chloride. The site of the anodic reactions and the reactions generat- ing manganese dioxide are uncertain and may change with time of operation. The anode behaves crudely as an oxygen electrode with

Jan 1, 1977

Timely disclosure of information germane to the taking of investment decisions makes an essential contribution to ensuring the growth, efficiency and integrity of our capital markets. It is a core contributor to the maintenance of fair, orderly and transparent markets. Australia has a strategic need to protect and enhance market integrity. Australia is ranked tenth in the Morgan Stanley Capital International (MSCI) World Index, yet represents only 1.59 per cent of that Index. In order to survive and grow in this globally competitive environment, Australian capital markets û the drivers for economic activity in Australia û need to attract foreign investment and engage retail capital. The communication of relevant and comprehensible information to the investor plays a vital part in fostering investor confidence, thereby building depth and liquidity in our market. We have had a rewarding partnership with the mining industry to develop and recognise reporting standards which could allow ready comparability and investor understanding of the mining investment vehicle. Our mining market has been successful because of the high standards of professionalism and the intellectual capital that has been built up among the participants û the mining professionals, brokers, analysts, mining investors, professional advisers and the market operator. The balance of knowledge and understanding among these participants combined with the competition for capital, contributes to the standards for our mining market in a way that the market operator simply cannot replicate by market rules alone.

Jan 1, 2002

AustraliaÆs record-breaking drought, efforts towards environmental best practice and the current commodities boom is demanding water use and reuse as never before. Mining practices, processing, the remote communities and support industries require vast amounts of specific quality water. Sustainability of water use has been a key factor in mine development, expansion of existing operations and increasing profitability of processes involving water. Developments in water treatment technology have enabled the use of a range of processes to produce this water reliably at ever decreasing costs. This increasing acceptance of new technologies has seen seawater desalination, recycling of plant wastewater streams, municipal wastewater reuse and others to become commonplace. Processes including seawater and groundwater reverse osmosis (RO), low pH RO, thermal desalination, high rate clarification, brine water treatment, ion exchange and other advanced treatment technologies are now used as part of mining operations. This paper surveys the trends in water treatment for the mining industry both in Australia and internationally with a review of technologies and case studies of operating plants. The key technologies are explained with an emphasis on the specific requirements for mining operations û unusual raw water, process and operations limitations, environmental concerns, as well as harsh climate. Case study information from several mining operations is included.

Jan 1, 2006

The resistance of lead to chemical attack and the ease of its fabrication has made it one of the most useful of the metals available to the chemical engineer and the electrometallurgist. It has proved to be of particular value in the manufacture of sulphuric acid, and since the conversion of the sulphur of pyritic ores into sulphuric acid is becoming the duty of the metallurgist, the corrosion resistance of this metal will be a matter of considerable interest to him from the standpoints of both producer and user. He realises that there is little to be gained in carrying the process of purification past the ordinary economic limit if little or nothing is to be added to its corrosion resistance, and he as user would not be willing to pay a premium for such purification if it can be shown that its reputed value has no scientific foundation.The metallurgist is well acquainted with the trouble and expense of meeting demands which have nothing torecommend them but prejudice and fancy. The valuable anti-corrosive properties of lead are very commonly ascribed to its forming insoluble compounds with the acids sulphuric, hydrochloric, carbonic, etc. If we trusted superficial visual evidence alone, such a view would receive strong support, but in the light of what we know of the mechanism of corrosion we must attribute its resistance to other factors much less obvious to casual inspection. Certainly there may be some mechanical obstruction set up to diffusion of the liquids towards the surface of the metal.

Jan 1, 1932

By M Delaney

Alliancing is a contractual relationship in which organisations with an interest in a project are brought together in an atmosphere of co-operation to produce superior results to benefit all of the participants. Fundamental to the concept is the management of the risks associated with the project. The traditional risk management strategy adopted by clients has been to transfer this risk to others in the belief that this will result in the lowest overall project cost. It is assumed that competition in the market place will allow these risks to be transferred without paying a premium. However, this approach often results in the development of an adversarial climate, a high level of litigation, time and cost overruns and an overall poor project outcome. Under an alliancing arrangement the parties (client, designer and contractor) are aligned through shared interests in the projectÆs success by linking profitability to performance. Under such an arrangement, an atmosphere is created whereby the participants are motivated to focus on cost-savings, pursue best value and to innovate. Successful alliancing can result in highly motivated project teams and realisation of extraordinary productivity and cost-savings flowing from increased efficiencies. The situations in which alliancing can be successful are discussed with particular reference to the Wandoo Alliance which successfully completed the $375 million Wandoo B offshore oil platform in record time and with considerable savings to the project budget.

Jan 1, 2000

By J P. R de Villiers

The Vanderbijl Park sinter plant in South Africa was investigated to determine the reason for the production of very fine sinter not acceptable as feedstock for the blast furnace. A procedure was designed to generate representative samples and to prepare the samples for chemical and mineralogical analyses. Results from a mineral analyser showed that the samples are extremely heterogeneous and therefore the sampling and sample preparation methods had to be tested in order to produce representative samples. The high production capacity at the sinter plant could also give rise to sampling errors. The method designed involved sampling of the conveyor belt at the sinter plant every four hours for the duration of three days. The samples were then milled and split into smaller sections appropriate for analysis. X-Ray diffraction (XRD) and X-Ray fluorescence (XRF) analyses were conducted on the samples. The results showed a standard deviation of less then one per cent, which indicates that the samples were representative and that the method used was therefore adequate. Systematic differences in the phase proportions between normal and fine sinter samples were detected, with the fine sinter containing more haematite than the normal sinter. The sampling method employed gives added confidence that the differences are real.

Jan 1, 2008

THE following paper is a description of the plant and operations of the above company in their recovery and treatment of the quartz tailings deposited as final residues by the various mining companies. at Waihi, Karangahake, and Waitekauri into theOhinemuri River. During the past few years the silting of the Ohinemuri River has increased to such an extent as to cause considerable interest and discussion, and has lately been the subject of a most extensive inquiry by a Royal Commission, to consider the best means of dealing with what is generally spoken of as a public nuisance.Ever since the commencement of mining in this district, which was opened as a goldfield in 1875, the various mines operating have been discharging their tailings into this river, it having been proclaimed a sludge channel in 1895. Up to the year 1900 the quantity of quartz crushed was not large, probably not exceeding 500,000 tons; but since that date the annual tonnages discharged have increased enormously, and at the present time would total from 550,000 to 600,000 tons per year. Records show that up to the end of 1910 at least 5,000,000 tons have been crushed, for an actual yield of bullion considerably exceeding £10,000,000 in value, and all the valuable tailings from...

Jan 1, 1911

By Hinkley JT, Smitham JB, Nicol SK

Historical investigations of mineral flotation have highlighted the many factors which affect flotation. Some of these are related to the mineral, its degree of liberation (however defined), solution chemistry and flotation reagents. The complexity of the interactions between these factors often leads to uncertainty over whether the final grade/recovery results obtained in either laboratory or pilot scale tests are in fact the maximum recovery at a specific grade. The reason for this is that there has not previously been a general technique for establishing the floatability of an ore. This study describes the further development of the 'tree' flotation technique for minerals other than coal, and in particular its application to iron ores. Oxides have been chosen as a system of intermediate complexity between the simple coal system and sulphide minerals to illustrate the principles and develop the concepts. The 'tree' flotation procedure consists of the progressive flotation to completion of successive froth products, followed by reflotation to remove entrained material. It therefore represents an 'equilibrium' approach to floatability rather than a kinetic approach. By ordering the various products and tails in order of increasing grade, a cumulative curve of grade and recovery can be constructed against which an isolated batch or plant result on the same ore can be compared. In this investigation, a Jaspilitic iron ore was tested at various grind sizes to determine the 'best' flotation grade-recovery that could be obtained with a given set of reagent conditions. The separation characteristics of a process are best measured on a system which contains particles which behave as 'middlings' with respect to the process in question. For this reason a natural ore was chosen in preference to model systems in order to relate more readily to plant situations.

Jan 1, 1993

By Churchill J

A suite of software programs has been written to provide the field engineer or geologist with the capability to collect and store data directly into small, portable handheld computers. This allows the engineer and geologist to collect data in a more efficient manner as the data is collected in sequence and is verified at the time. Typical applications for this software include geological and geophysical logging, trucking surveys, mine surveying, condition monitoring, ventilation surveys and maintenance systems. The software allows the user to construct his own electronic notebook by structuring data input to the computer in a similar manner as is now done on pre-printed forms. The user can store all valid entry codes or numeric ranges in a dictionary and all data inputs made are validated against this dictionary. Once constructed the user may call the electronic data sheet into the unit and collect data which will be stored into the unit which has the memory capacity to record data for up to periods of 60 hours. The data can then be automatically transferred to mini/microcomputers for immediate analysis and report generation. The software may be used on a variety of handheld computers.However the generally rugged environments found in the mining industry limit the choices. In particular the authors have selected a unit weighing a little over one kilogram, which is rugged enough to fall off an underground survey vehicle, and survive when accidentally immersed in water,without losing data. This paper describes the software developments in detail. The project development work to produce this system has been funded by a grant from the Australian Mineral Industries Research Association and is supported by a number of large Australian mining companies.

Jan 1, 1986

By Kim M

Mukuk gold mine in South Korea produces a pyrite concentrate containing gold associated with arsenopyrite as a gangue mineral. The effects of Portland cement as a depressant on the flotability of arsenopyrite were studied to improve the separation of arsenopyrite from pyrite concentrate containing gold. A series of the fundamental flotation tests were performed using Portland cement as a function of pH and concentration of the collector. Flotation recovery of pyrite and arsenopyrite in the fundamental tests with amyl xanthate showed that arsenopyrite was depressed by the addition of a moderate amount of Portland cement, but pyrite was not depressed by it. In the flotation tests of the artificial mixture samples with arsenopyrite and pyrite, following pH were adjusted to be 10.5 by Portland cement, different amount of amyl xanthate was added. The results from these studies showed that flotation recovery of pyrite was 100 per cent under the condition of some addition of amyl xanthate, but arsenopyrite was not floating at all. Portland cement shows remarkable depression of galena, but its effect on the flotability of chalcopyrite is not as clear. In the pulp under Portland cement addition, chalcopyrite can be easily activated by the addition of sodium bisulphite, whereas galena is depressed more effectively. From the batch flotation tests with the pyrite concentrate, the galena concentrate and the Cu-Pb bulk concentrate from the mines, it was confirmed that the results of the batch flotation tests agree with the results of the fundamental flotation tests. The effects of depression by Portland cement on pyrrhotite, marmatite and stibnite are also discussed briefly.

Jan 1, 1993

Silver and gold bearing ore from the Palmarejo mine, located within the Mexican state of Chihuahua, contains a complex mix of electrum, native silver, silver sulfides and silver chlorides. This paper presents a case study that describes the selection, development and engineering of a tailored process plant for the recovery of silver and gold from this ore. Process circuit feasibility study modelling, metallurgical test work and engineering studies are outlined. Options considered to optimise the recovery of the contained silver and gold are compared, based upon cost, operability, recovery and engineering aspects. Concentration by flotation was found to be the preferred primary recovery route. Intensive leaching of the flotation concentrate resulted in solution grades sufficient to allow direct electrowinning to be evaluated against the more traditional Merrill Crowe process. The flotation tailings stream is processed through a separate leaching stage as there is sufficient economic metal extractable from this stream. The processing flow sheet, which is designed to maximise the recovery from both the flotation concentrate and tailings, and to utilise a common metal production facility, is presented.

Jan 1, 2009

Accidents in open pit mining have a high cost in lost time of person- nel, damage to equipment and installations, and lost production. The realities of export competition require that Mine Management sig- nificantly reduce the costs associated with accidents and workplace ill-health. Newer management approaches are proving effective in reducing the Total Cost of Risk through a strucured Occupational Health and Safety Programme exhibiting the following features: ò Formal Company Policy ò Accountability for OH&S performance clearly designated to each level of management and supervision ò Effective utilisation of a Mine Occupational Health and Safety Co- Ordinator and a Mine Occupational Health and Safety Adviser ò Development of realistic OH&S Objectives ò Training of Management, Supervision and Workforce in Occupa- tional Health and Safety ò Development and adoption of Safe Work Practices and Procedures ò Effective employee selection procedures, control of Contractors ò Monitoring of the health of the workforce ò Collection, recording and distributing information on all Mine inci- dents, accidents, injuries and damage ò Ensuring that the Mine environment is healthy and safe ò Effective Emergency Procedures to deal with injury, fire, rescue and other situations of risk ò Controlling those Mine hazards which cannot be removed ò Adopting a high standard of Occupational Rehabilitation ò On-going visible Management participation in the programme to ensure that momentum is developed and maintained. This approach requires that Occupational Health and Safety be given equal status with product quality, maintenance of plant and output per- formance; its implementation is rewarded with improved morale and major cost reductions.

Jan 1, 1989

A key premise to this paper is that most people involved in the design and implementation of drilling and blasting operations could benefit from a greater understanding of the geological materials, deposits and landforms they are dealing with. The second key ingredient for successful blasting is the concept of blasting objective. Mine operators and blasting contractors must be clear on what drives their costs (blasting leverage) and should formulate blasting objectives and operational targets which help in this regard. Many operators ignore geology descriptors and features apart from the name of the rock and start crudely quantifying the rock mass properties in terms of uniaxial compressive strength, or even worse still as hard or soft. This occurs too early in the design process and not much attention is paid to the geological materials, geological structures and the characteristics of the deposit they intend to excavate. In effect the rock type name and the strength descriptor become the site geology. Furthermore many blasting operators do not formalise their blasting objective, do not set operational targets and do not measure results to the degree required for continuous improvement. In this paper a number of civil, surface mine and underground mine blasting applications are tabulated in terms of typical blasting objectives and common geological materials. A good description of geological materials can convey a lot of useful information for blasting operators if they are able to accommodate this knowledge. In addition a clear statement of the blasting objective and associated operational targets will maximise the likelihood of achieving blast-driven downstream productivity improvements. The æStarting at Both EndsÆ combination is deemed extremely useful for any continuous improvement blasting program.

Jan 1, 1999

COAL constitutes such a gigantic item in modern industry, either for direct heating, production of coke for smelting, or for the generation of power, that its quality and price play a very significant part in economic industrial progress. Australia is still a very young country industrially, and is groaning under many disabilities compared with competitors overseas, not the least of which is the quality of coal. Linked with the word "quality" should be that of "utility," for high-ash content prevents efficient utilization of the fuel.The marketing of good quality coal is a very important matter indeed, and if industry in Australia is to progress in the way that it should, this matter must receive keen attention.New South Wales, above all the other Australian States, has been blessed by nature with vast coal-fields, from which fuel is shipped to every State, and provides the base for power for most of our railroads and industries.Experts frequently refer to the fact that in some districts only partial extraction of thick seam coal is being made, without a care or thought for the future. Ranking next in importance to this is the fact that much of the coal is being carelessly marketed.Very few collieries in Australia are equipped with coal-washing plants for dealing more particularly with small coal grading which most industries require, and to which coal producers as a whole pay the least attention. In England each year nearly20,000,000 tons of coal is being water-washed before sale, and is marketed as a fuel of far greater utility once it has been freed from extraneous ash.Investigation proves that a great many pits in New South Wales are marketing coal (more particularly small coal) containing a considerable quantity of extraneous ash, due to the admixture...

Jan 1, 1926

Education and Training for the minerals industry has been identified as one of the key priorities by the AusIMM and many closely related groups. The AusIMM Education Taskforce has been engaged, through a visioning exercise, in evaluating what minerals education and training should look like by 2025. A common recurring theme is that for minerals education and training to be efficient and effective into the future, it needs to be comprehensive and inclusive. Some previous attempts to achieve efficiency and effectiveness have had limited success, mainly due to approaching the issues involved from a narrow, singular perspective. This paper outlines that the achievement of the desired outcome may require an approach that parallels the same techniques that are used for multi-dimensional mine planning, treating tertiary minerals education and training in a similar way to the planning involved for a complex orebody. Just as efficient and effective mine planning requires engagement and understanding of many factors, so too does engagement with tertiary minerals education and training. The major factors that need to be considered are outlined in the paper, including: levels of tertiary education and training; Australian Qualifications Framework (AQF), Levels 1 to 13: systems of minerals education and training, such as higher education, (mainly universities), industry/professional associations and licencing requirements, vocational education, (mainly TAFE) and workplace programs; types of minerals or mining methods involved; volume of delivery; stage in the flow sheet, (geology, mining, beneficiation, extraction, refining). For comprehensive mine planning there is the need to develop links or roadways and openings between different levels of a mine. Similarly, to achieve a comprehensive tertiary minerals education and training model, there is a need to develop pathways, recognition and credit transfer between the various levels and components of minerals tertiary education and training.

Jan 1, 2005

The history of black coal as a fuel dates back in Europe more than 2,300 years, and possibly longer in China. Originally the mining of coal was done by underprivileged people, but with the industrial revolution and the dawn of mechanisation, the status of the coal miner improved. The improvement continued to the present day. Coal miners now take an important role in industrialised countries and enjoy a high standard of living. The miner is amongst the highest paid and best technologically served in any industrial activity. The abundance of coal relative to alternative fuels and its widespread occurrence, brings with it a prosperity much valued in those countries with significant resources such as Australia. Coal will play a major role in easing the world energy shortage. In addition to the conventional usage, throughout the world coal gasification plants are in various stages of development. Coal liquefaction plants are beyond the drawing board stage. Slurry pipelines to supply coal for direct burning in electric generating and other plants are planned. In the current atmosphere of environment consciousness, Australia has to contend with people with only marginal interest trying to influence coal mining activities to the detriment of the overall prosperity of Australia. Fortunately enlightened legislation is the greatest protector of the environment and in many instances great improvement to the environment ensues after mining has passed. With its vast resources of black coal Australia can look forward to a significant role in future supply of fuel. As a result of the trade and industry involved, Australia can become an even more influential country in world politics, trade, and the setting of high living standards.

Jan 1, 1975

Environmental leaching methods such as the toxicity characteristic leaching procedure (TCLP) test or the ASLP test are used to assess wastes including mining and mineral processing by-products. These tests were initially designed as regulatory tests simulating conditions in a co-disposal municipal landfill waste facility and do not allow leaching performance to be predicted in site specific scenarios. Further, the assumptions underlying these tests tend to define worst-case scenario leaching conditions for by-products from the mineral industry disposed of outside a co-disposal scenario.   Recently some characterisation leaching test methods have been issued as ISO/TS standards (ISO/TS 21268-3:2007 and ISO/TS 21268-4:2007) that aim to define the leaching performance of soil type wastes and to predict the leaching performance of these wastes over long time frames. In this preliminary work these standards are trialled for by-products from the mineral industry and the quality of information that can be obtained from them compared to TCLP/ASLP tests.   Where clear comparisons were possible, the TCLP/ASLP tests were typically found to extract a similar, or often greater, amount of component than (i) tests conducted at the same pH but without the acetate buffer or (ii) for test conditions aimed at simulating long-term leaching in an eluate defined by the waste type. While further work is required, the preliminary results indicated that the tests may provide reliable long-term estimates of leaching performance of wastes in soil types of variable pH and provide a suitable basis for long-term planning for optimal waste handling, treatment or even re-use.

Jun 1, 2010

By V Narayanaswamy

SustainabilityÆs imperative of economic development in tandem with social advancement and environmental protection is widely accepted, but much debate remains about the practical implications for the minerals processing technologies and practices for the future. Experience in other industry sectors however suggests that sustainability can be a value-adding framework for innovation in processing technologies, business models and management systems. This position paper explores how sustainability can drive innovation in minerals processing, by reviewing pertinent ideas and experiences gained in non-minerals sectors. Sustainable innovations can generally be broadly ranked from incremental to transformative, with each category having its own typical improvement potential, timescale and technological and operational challenges. This leads to a æmud mapÆ for sustainable innovation in minerals processing with three distinct tracks: eco-efficient operations; sustainable plant design and sustainable processing. Competing models for the sustainable innovation process through either forecasting or back-casting, have in common the strong reliance on vision, perspective and competency, which in turn highlights the importance of sustainability frameworks. Such sustainability frameworks provide normative goals and option elicitation prompts to assist with the analysis of current processes and scoping of more sustainable alternatives. A comparative analysis of five prominent environmental sustainability frameworks revealed three cross cutting sustainability themes that challenge current resource processing technologies and practices. These are: fate of materials (zero dissipation of materials); compatibility of materials and processes; and materials intensity of industrial products and processes. Although the sustainability concepts presented in this paper have not been extensively road tested in the minerals processing industry, there is ample evidence that recent initiatives in the Australian resource sector illustrate the applicability of the proposed framework. It is therefore argued that more in-depth assessment of sustainable innovation concepts would be a valuable contribution to the sustainable resource processing theory and practice.

Jan 1, 2004

At the outset I want to thank you for inviting a representative of the Chamber of Mines of South Africa to address you on the subject of mining and its future at this, the 13th Congress of the Council of Mining and Metallurgical Institutions. It is indeed a pleasure and an honour to be here. As many of you will recall, four years ago I, as the then President of the South African Institute of Mining and Metallurgy, had the privilege of hosting and welcoming you to the 12th Congress, the third such congress hosted by South Africa. The late Sir Ernest Oppenheimer, President of the 1930 Congress - the first to be held in South Africa - in his opening address foresaw the mining industry as "the most potent factor in spreading the benefits of civilisation over the sub-continent." We have come a long way since those halcyon days but, as I noted four years ago, it still remains true that mines have been, and will continue to be, the missionaries of development in many, if not most, of the Third World countries. I have been asked to address you on the subject of "mining" and to let my imagination roam widely so that delegates can leave the congress with a broader vision than they brought on arrival. It is a tall order and in my attempt to fulfil it I ask you to cast your minds back 120 years to a sultry, rustic day when the first diamond was discovered in South Africa at the now famous town of Kimberley. At that time the South African economy, predominantly pastoral, was still at subsistence level. Almost overnight the ensuing diamond rush turned the then British- owned northern Cape Colony's semi-desert scene into a hive of mining activity, every prospector bent on making his instant fortune. It was very little different, I am sure, to the gold rushes that hit California in 18+8, Australia in 1851, New Zealand in the 1860s. and the Yukon in the 1890s.

Jan 1, 1986