Search Documents

The geotechnical factors controlling the design of the open pit slopes of the Pasminco Century Mine near Lawn Hill, Queensland are presented below. Pasminco Century is a stratiform shale hosted zinc deposit in the Lawn Hill Formation that is overlain in part by the Thorntonia Limestone Formation. Both the mineralisation and overburden is located within a competent rock mass such that intact rock strength and discontinuity spacing is generally sufficient to prevent large-scale slope failure by breakage through the rock mass. Rather, overall slope stability issues are dominated by the major discontinuities within the rock mass. The deposit is located in a structurally complex regime, it consists of a synclinal basin which is truncated by easterly striking normal faults through its centre and northern and southern limits and by an unconformity on its eastern and western margins. Deposit geometry and slope stability is further complicated by small-scale folding, a pattern of northeast and southeast striking subvertical faults and north easterly dipping thrust faults with their associated fault emplaced blocks of Lawn Hill Formation in the overburden. The large size of the deposit requires a staged mining approach with the excavation of both final pit walls around the external sides of each stage and interim pit walls along the internal boundaries between adjacent stages. The deposit geometry and major discontinuities control not only the final pit wall design but also interim wall location and orientation, excavation sequence and in some stages the excavation schedule. Two and three-dimensional limit equilibrium stability analyses were conducted using both deterministic and probabilistic approaches to determine appropriate pit wall design criteria and to select a suitable excavation sequence and schedule.

Jan 1, 2000

By G J. Jameson, A Agarwal

This paper is concerned with the observation and analysis of bubble clusters in a laboratory flotation cell. A device was used in which bubbles were allowed to rise in clean water containing the same frother and collector concentration as in the cell. Bubble clusters were recorded using a high speed camera and analysed using an image analyser. Dodecyl amine was employed as a collector to float silica. The effect of impeller speed on the cluster behaviour was investigated. The results were interpreted in terms of cluster diameter and shape factor. The sizes of the bubbles forming the clusters were also measured and compared to the sizes of the independent bubbles in the cell. It was found that there was an optimum impeller speed in which the cluster diameter was a maximum. Higher agitation and the consequent higher power inputs resulted in cluster break-up while lower shear rates promoted cluster formation.

Jan 1, 2005

By C Antonio, R Narayan, A Scheuermann, S Quintero, M Edraki, M Ziemski

Tailings are mostly loose material and can be classed as non-plastic sandy silts. They also tend to have low permeability, resulting in slow consolidation (settling) rates and low shear strength, even after consolidation. These qualities make them prone to liquefaction and, therefore, physical instability. In contrast, coarse waste rocks possess high shear strength and permeability when stacked in dumps. However, air and water flow-through the voids can cause acid mine drainage (AMD) with significant undesirable environmental implications. Combining the two waste streams before disposal by mixing presents a potential opportunity to harness the desirable properties of both waste streams. This practice is termed co-mingling and is prevalent within the coal processing industry. Co-mingling of metalliferous mine tailings is, however, a relatively new concept. By combining the coarse waste rocks and fine-grained tailings streams, the fine tailings tend to fill the voids between the waste rocks, reducing hydraulic conductivity and advective air (oxygen) flow into the rocks, thus possibly reducing acid mine drainage (AMD). Conversely, tailings are introduced to large frictional particles from waste rocks, providing reinforcement, stability, and possibly improved drainage. New separation methods are being introduced to the mining sector, which have the capacity to extract waste with significantly larger particle sizes. High Voltage Pulse (HVP) is a technology in which relatively coarse particles ranging in size from 30 to 100 mm are exposed to an electric pulse discharge. This pulse preferentially fractures mineralised particles while leaving unmineralised rock (gangue) intact. The stream can then be passed via a screen, with smaller mineralised particles reporting to the undersize and removing coarser unbroken barren particles, thereby eliminating waste. Coarse particle flotation (CPF) is another emerging new technology in metalliferous mining that applies flotation separation to coarser particles than conventional flotation. These new technologies produce different tailings (waste) streams with varying physical characteristics and possibly surface chemistries. This research aims to test new tailings mixtures by applying the co-mingling concept to blend the reject streams generated by these two technologies (HVP and CPF) with the tailings produced by conventional flotation. Combining different waste streams before disposal can improve stability and potentially reduce the acid mine drainage (AMD) rate, thus enabling early access to the tailings storage facility for rehabilitation and closure.

Aug 2, 2023

Laboratory tests were conducted to study the effects of thrust or pull-down force and rotary speed on the vibration signatures of a particular drill in a known rock type, and to determine how the vibration signatures could be used to assess bit wear. The vibration signatures were analysed using a Wavelet Transform analysis technique, which decomposes the signals in multi-bands of frequency and presents the results simultaneously in time and frequency domain. Results show that as the bit wears, large fluctuations in amplitudes in the high frequency ranges occur, and prominent peaks in the low frequency ranges were observed for a worn bit. The Wavelet Transform technique provides an appropriate and effective metrics for monitoring and evaluating the state of wear as drilling progresses through the post-processing of wavelet coefficients. This study provides a basis for the development of an on-line detection technique of bit wear in rock drilling through Wavelet Transform technique or time-frequency analysis that can be used in real time.

Jan 1, 2000

By T GRAHAM-TAYLOR

A trend towards mining more complex and economically marginal orebodies, often combined with increasingly tight product specifications, increases the number of variables which need to be considered in production scheduling. Linear programming incorporating integer constraints can be used to create production schedules which are practical as well as mathematically optimum. Factors which can be taken into account include variability in product stockpiles, targets for head or product grades, production of different material types, production from different areas, production targets for loaders, and dependencies between mining blocks. For each schedule an appropriate objective for optimisation must be chosen. Examples of objectives are: to minimise or maximise grade variation; to minimise waste movement; and to minimise movement by front end loaders. A staged approach to the implementation of computer systems based on linear programming optimisation is Proposed.

Jan 1, 1992

By Mine F. J, Woods P. H

Waste waters from mine sites may be screened for all constituents of significance as a first step in establishing water quality criteria for protection of aquatic ecosystems. Inductively-coupled plasma mass spectrometry (ICP-MS) offers the capability to screen water samples and digest solutions for virtually all elements in the periodic table. This technique is therefore able to identify elements whose concentrations are elevated in waste waters and may be rarely present in background surface or ground waters. Such elements may be present in waters at only a few ¦g/L. ICP-MS has sufficient sensitivity to detect sub-¦g/L or even ng/L levels of many elements. Waste waters from most mining activities in the Northern Territory have been examined by ICP-MS. The concentration data provide the basis of a contaminant data base. The data can show specific tracers in the ore or mineral itself, subsequently found in waste water. An example is the presence of rhenium in uranium ore. Such trace elements may be present in soluble or insoluble chemical forms and are more useful as indicators when soluble and exemplifying conservative chemical behaviour. The approach described, based on ICP-MS screening of mine site waste waters, together with general physico-chemical variables, provides the most comprehensive means yet available of selecting variables for monitoring programs and ensures that key elements and/or their chemical species are not excluded from monitoring programs.

Jan 1, 1994

By G Johnson, G W. Wilson

The settlement and drainage behaviour of co-mix, or mixtures of waste rock and tailings, are examined in a column study. Three co-mix profiles were observed for settlement, drainage, and pore water pressure response. A fourth profile with waste rock and no tailings was also observed for settlement. Co-mix consolidated faster than predictions for tailings alone, and maintained a saturated void space relative to waste rock alone. Practical benefits of co-mix as a waste disposal technology may include faster time to consolidation than tailings, a reduction in total settlement of placed material compared to tailings alone, and a reduction in acid drainage by limiting the flow of water and oxygen through maintenance of a saturated void space.

Jan 1, 2003

By D Van Doorselaere

The purpose of blasting during mining is to produce a muck pile that can be efficiently loaded and transported. There is an increasing awareness of the variation in muck pile characteristics and its economic implications. It is well known that good fragmentation by itself is not sufficient to optimise the muck loading efficiency. The swelling and configuration of the muck pile also significantly affect the productivity of the loading equipment. The characteristics of a muck pile depend upon the blast design parameters, explosive properties and rock mass geology. This study has focused on the dependence of muck pile configuration on blast design parameters, explosive properties and size distribution of the muck.The field work was done in two phases. In the first phase 12 blasts were monitored, while in the second, three blasts were monitored. The blast design parameters and explosive properties for each blast were documented and the following muck pile characteristics were measured:muck pile height and its distance from the facedistance of throwwidth of the power troughsize distribution by image analysis technique.The effects of burden, bench height, heave energy of explosive, row-to-row delay, powder factor and the mean particle size of the fragments on muck pile configuration were examined. It was observed that muck pile height and distance of throw are strongly influenced by the burden, bench height, heave energy of the explosive and the size distribution of the muck. The width of the power trough depends upon the row-to-row delay, powder factor and total burden. In addition, the effect of the fragment size distribution on the muck pile parameters has also been discussed.CITATION:Singh, S P and Van Doorselaere, D, 2015. The relationship between blasting parameters and muck pile configuration, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 369–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By P A Ferenczi

The Proterozoic iron oxide related Au-Cu-Bi (Tenant Creek style') deposits at Tennant Creek can be classified as syntectonic polymetallic hydrothermal replacement type mineralisation. These deposits have characteristics in common with a number of other Proterozoic iron oxide (Cu-U-Au-REE) hosted deposits in regions which include Southeast Missouri, USA; the Kiruna district, Sweden; the Great Bear Magmatic Zone, Canada; the Stuart Shelf, South Australia; and the Wemecke Mountains, Canada. Similarities between these and Tennant Creek style deposits include: 1. Tectonic Setting: Formed at shallow crustal levels (

Jan 1, 1994

A practical approach has been developed for the design of both grates and pulp lifters. It is based on: an appreciation of the process interaction between grates and pulp lifters, an interpretation of mill charge structure as it relates to discharge through grates, and an analysis of pulp and solids flow in pulp lifter channels. This approach can be used to improve the overall discharge effectiveness of AG and SAG mills.

Jan 1, 2000

By P K. Seccombe

The McKinnons gold deposit is hosted by weakly deformed, Palaeozoic metasedimentary rocks of the Cobar Basin in the western Lachlan Fold Belt of New South Wales. Mineralisation comprised a largely supergene resource of 1.7 Mt of ore, grading 1.7 g/t gold, established over structurally controlled, primary gold and base-metal mineralisation in underlying, carbonate-rich meta-siltstones and sandstones of Early Devonian age. Mineralisation was associated with at least two major fluid cycles. The first cycle was characterised by four stages of vein formation. Early quartz and carbonate veins (Stages 1 and 2) and quartz-pyrite breccias (Stage-3) occurred prior to, or early in, the main regional deformation (D1). Continued D1 deformation produced syntectonic, carbonate-base-metal veins (Stage-4), primarily in dilatant zones adjacent to fold axes. The second cycle of mineralisation was an epithermal-style event, driven by a shallow, syn-D2 or post-tectonic intrusion, defined by aeromagnetic imaging. The intrusion may have exploited a jog, controlled along the basin margin by basement faults. Mineralisation produced gold-pyrite veins, associated with pervasive quartz-sericite-adularia and chlorite-sericite alteration. Highest primary gold grades are confined to quartz-adularia boiling zones. The McKinnons deposit offers an important example of mineralisation formed by multiple processes. Early-stage, base-metal mineralisation at McKinnons reflects structurally focussed, basin dewatering and metamorphic processes, typical of other deposits in the Cobar Basin. By contrast, late-stage gold mineralisation at McKinnons is magmatically driven and of epithermal style. Recognition of overprinting distinctive geological events is critical, not only in modelling ore formation, but in developing a versatile exploration concept.

Jan 1, 1999

Getting it right is a very profitable outcome. Shareholders would ideally like to see their directors get it right all the time on the major economic decisions. But it is very difficult for mining directors to get it right all the time in such an uncertain environment. Primary decision-makers of companies with significant stakes in the mining industry should get it right much more frequently. The legal measures of evidence (beyond reasonable doubt and on the balance of probabilities) can be used to determine whether grade estimates (a key revenue variable) are realistic. The application of this approach can be far reaching. More frequently correct decision-making would result in more effective allocation of limited resources (capital and labour). In turn, this would result in higher financial returns and a more extensive mining industry.

Jan 1, 1994

The Beverley uranium mine û now in production in the remote north of South Australia at1000 tonnes per annum û was established to meet a projected, but little-recognised shortfallin primary supply of uranium for the nuclear industry in the early part of the 21 st century. Inthe context of AustraliaÆs lack of bi-partisan support for uranium mining and the nuclearindustry, a four to five year window of opportunity existed from 1996 to establish the mine.During this period, Beverley achieved a number of firsts including: the first ISL mine inAustralia; the largest ISL mine in the world and the first to produce more than 500 tonnes ofuranium in its first year; the first to be established under a new Native Title regime in SouthAustralia; and the first to be established under a revised South Australian Mining Act.Beverley was brought into production against the background of: hostile opposition fromanti-nuclear activists; a suspicious and at-times hostile media; a regulatory and politicalcommunity that was unfamiliar with ISL mining; commercially unsophisticated Aboriginalgroups; an inexperienced engineering industry; and the vagaries of development in a remote,semi-arid location with neither population nor infrastructure. The lessons that can be learnedfrom Beverley showed that û like much in life û flexibility and timing are crucial.

Jan 1, 2002

By T R. Justice

The Eastern Distributor tunnel is located approximately 24 m beneath the suburbs of Woolloomooloo and Darlinghurst to the east of the central business district of Sydney. The 1.7 km long tunnel will carry three lanes of northbound traffic over three lanes of southbound traffic in a æpiggybackÆ arrangement, with a maximum cross-section 22 m wide by 12 m high.The tunnel is constructed predominantly within horizontally bedded Hawkesbury Sandstone. In the unweathered to slightly weathered state, the rock is typically medium strength (average UCS about 24 MPa), with an average quartz content of 72 per cent.Major geological features that intercept the tunnel route are the Woolloomooloo Fault Zone and two extremely to moderately weathered dolerite dykes. The fault zone intersects the tunnel at about 25¦ to its alignment and comprises a series of discrete faults over a width of approximately 50 m. The overall movement of the fault zone appears to be reverse. The two dykes are the 1 m wide Oxford St Dyke and the 6 m wide Great Sydney Dyke.This paper outlines the site investigations and the interpreted geotechnical model for the tunnel route prior to the commencement of tunnelling. This model is then compared to the encountered conditions. The very good correlation between the expected and the encountered conditions shows the high quality of geotechnical investigation and interpretation.

Jan 1, 1999

By R Forster

Direct ship iron ore (DSO) operations at Extension Hill in Western Australia’s Midwest region have commenced, with fi rst product railed to the port of Geraldton in July 2011. Reserves are 14.8 million tonnes (Mt) of haematite-goethite ore overlying an Archaean BIF-hosted larger magnetite deposit which Mount Gibson Iron Limited (MGI) sold to other parties in 2006.Some unique geological aspects of the deposit shape DSO mining and processing operations. Owner-operator selective mining, blending, crushing and screening on site will produce three million tonnes per year (Mt/a) of Lump and Fines product to be trucked 86 km to Perenjori, railed 232 km to Geraldton, and loaded aboard Panamax-sized ships through the dedicated iron ore shiploader at the Geraldton Port Authority’s Berth 5 facility.The statutory approvals process for this project formally began in 2004, dominating delays in a predevelopment phase which extended over a longer period than the likely life of DSO operations. The lack of transparency, uncertainties and costs inherent in state government processes have influenced decisions made by MGI while assessing other development opportunities in Western Australia. Potential for additional Reserves exists at Extension Hill, however MGI’s ability to extend the mine life will hinge on statutory approval to explore for and evaluate other DSO resources on surrounding granted mining leases.The nature of the resource and use of existing infrastructure for product transport have enabled MGI to keep operating costs and capital intensity of this project relatively low. A tenacious development approach by MGI and robust project economics have fi nally enabled this site to take its place as a revenue earner beside the company’s other DSO operations at Tallering Peak and Koolan Island.

Jul 11, 2011

For the purposes of this paper the Newcastle Coalfield is considered to be that 35 km wide rectangular tract of country west of a line running 45 km along the coast, south from Newcastle.

Jan 1, 1993

By Boyle L. A

A positive displacement pump is being dev eloped for pipeline transportation of coking coal to a -50 mm export specification, at a con- centration and velocity which will allow trans- portation in the plug flow region, minimising degradation of the particle structure, and pipe= line friction losses which will be lower than with turbulent or laminar flow. Pump operation is by hydraulic powered free pistons in a rota- ting cylinder block, with cylinders overlapped by stationary inlet and discharge ports in a water lubricated and sealed rotary valve. Before this development coking coal was not considered suitable for transportation in slurry form, for the valves in the double act- ing duplex piston pumps used for slurry pipe- lines, cannot be divorced from the slurry and require that the solid material must be reduced to a fines'consistency before introduction into the pump suction. The hydraulic transportation of 10 million tonnes of -50 mm coking coal, 50 km from the Bargo area west of the escarpment to an offshore shiploader at Port Kembla is feasible. Study shows that economic factors alone would dictate that the development of a pumping system for long distance transportation of coking coal is necessary. The greatest impact from the slurry transportation of coking coal would be the

Jan 1, 1976

The establishment of vegetation onto open cut mine spoil is dependant on the nature of the soil and rock strata of the overburden. Experience has shown that in the Bowen Basin of Central Queensland the nature of the minespoil changes considerably as subsequent and deeper mining strips intercept changing rock strata. The different mixes of strata at the surface of reshaped spoilpiles can produce variable response in the sown vegetation cover. It is usual that land features of mine sites are known in detail and are depicted on mine or locality maps. Subsurface strata and lithology descriptions are available and are used for planning of open cut mining operations. Surface and subsurface data can also be used to estimate the intrinsic nature of overburden through the use of fence diagrams. Lithology at points along a mined strip can be obtained and used to describe overburden. Indications are that correlations exist between salinity of overburden components and the response of vegetation. The developed procedure thus becomes a useful tool for the prediction of revegetation Practices.

Jan 1, 1987

By P Bartlett, K Naidoo

Premier Diamond Mine is planning a new, mechanised, block cave, with a production level approximately 1000 m below surface. A high degree of tunnel damage is expected, due to stress and the relatively low in situ strength of kimberlite. An evaluation of the timing of tunnel excavation, tunnel size and spacing has been carried out to define critical parameters for planning layouts and development schedules. Extensive use has been made of three-dimensional FLAC3D numerical models, calibrated against known rock mass behaviour at 650 m depth, to examine the influence of undercut advance on production level excavations. These were able to represent the effect of stress rotation on tunnels during undercut advance and the effect of an inclined undercut. The analysis has provided guidelines that are possibly applicable to any deep block cave layout. The choice of drawpoint layout is of considerably less significance than the proportion of ground extracted on the production level elevation prior to advancing the undercut. The analysis shows that damage to production development will be potentially severe if it is all excavated prior to advancing the undercut, or is mined directly beneath the undercut face. The development of the main production tunnels alone ahead of the undercut may be feasible, but no breakaways should be put in as they appear to trigger a rapid increase in the severity of damage. The optimal sequence is when all production tunnels are developed at least 10 m in plan behind the undercut, where the induced peak field stress is less than 20 MPa and a maximum support pressure of 100 to 500 kN/m2 is require to contain movement. The assessment showed that the conditions are not significantly improved by increasing drawpoint spacing from 15 m to 18 m. The vertical spacing between the undercut and production level beneath is investigated. Provided production level development is carried out beneath the undercut, there would appear to be little benefit in increasing the vertical spacing between the undercut and production level beyond the current 15 m to 18 m.

Jan 1, 2000

By P Kumar, J Safarian

Understanding how ore interacts with flux particles at elevated temperatures to create molten slag is crucial since it governs the dynamics of a chemical reaction. This study explores the smelting behaviour of pre-reduced Nchwaning manganese ore when combined with lime, with the objective of examining the evolving interaction between pre-reduced ore particles and lime over time. The research sheds light on the interaction between solid and liquid and the phases that emerge during this process. To achieve this, a sessile drop furnace was employed to rapidly heat the materials positioned adjacent to each other on an alumina substrate and to observe the smelting process as it unfolded over time. This method allowed for the direct observation of the melting temperatures and the flux-ore reaction progression rate, and the potential disruptive events that might occur. By comparing the molten interfaces of the fluxed materials at various time intervals, this study provides insights into the relative rate of slag formation from the two materials. The results indicate that the main slag formation initiated at approximately 1400°C and continued to advance with time, with complete mixing occurring around 1500°C. The possible phases formed were identified using Scanning Electron Microscopy and modelled using Fact Sage thermodynamic software. In addition, the iron particles in the pre-reduced Mn ore were separated and settled from a rich MnO-containing slag. It was found that the separation of molten iron droplets from the slag depends on the rate of solid MnO particles dissolution into the adjacent slag phase.

Jun 19, 2024