Search Documents

An Environmental Impact Statement (EIS) for a major mining development typically has to address various aspects of surface water management, including some which generally tend to be the more contentious: the diversion of rivers and creeks from areas disturbed by mining, and their rehabilitation; the effective management of disturbed area run-off via the collection, containment and treatment of contaminated water on site in sedimentation dams; the collection, containment and treatment of mine pit water; the decommissioning of surface water storages; final void water quality; and water discharge criteria. Environmental Impact Assessment processes for proposed mining developments in Australia at the state and commonwealth level usually involve a form of Initial Advice Statement (or Notice of Intent), Terms of Reference, an EIS, and a Supplementary Report (or similar) which responds to agency and public comment on the EIS. The EIS is used by approval agencies to decide the acceptability of the Project, and to set the conditions of approval. The conditions are often in the form of a state-issued æOperational LicenceÆ or similar. With mining, the initial approval at the EIS stage is often just a pre-cursor to various other planning related approvals, including obtaining a mining lease. Afterwards, mine plans and plans of operations must be submitted to government at various stages of the mineÆs life, ostensibly to provide the detailed mine planning over periods of one û five years. Despite all this additional planning and documentation beyond the submission of the EIS, government approval agencies are increasingly not satisfied with conceptual water management designs and commitments to an outcome (such as meeting a specified water quality standard) in the EIS. Agencies are also requiring sufficient water management design information to be convinced that the outcomes are achievable. To assist proponents of major mining developments, the Queensland Government has published Technical Guidelines for water management, and Environment Australia has published a æBest Practice Environmental Management in MiningÆ booklet on water management. In addition, the Australian and New Zealand Environment and Conservation Council (ANZECC. 2000) has published Water Quality Guidelines which provide an approach to water management, and provide receiving water investigation trigger criteria. So, what are the water management issues that are likely to be the subject of comment, debate and negotiation prior to the EIS being approved? and what commitments may a mining proponent have to make in order to convince the approval agencies that sufficient investigation and design has been provided? This paper provides some answers to this question, by reference to recent major mining proposals which the author has managed through state and commonwealth Environmental Impact Assessment processes.

Jan 1, 2003

By M Cooksey, Z Zhu, N Langrené, W Chen, T Tarnopolskaya

"Dynamic decision-making can significantly increase the value of mining projects and deliver better sustainability outcomes under conditions of uncertainty. Despite its benefits, dynamic decision-making is rarely used by the mining industry, possibly because of the complexity of the algorithms used to make sequential decisions under uncertainty and difficulties in visualising the optimal strategies. To achieve better outcomes in practice, decision-makers in industry would benefit from a tool that would help them to understand and implement the results of the analysis.CSIRO is developing innovative dynamic decision support tools that include an intuitive graphical display of the boundaries between the regions of different optimal decisions, which would significantly assist optimal sequential decision-making under uncertainty. The dynamic decision support tool is based on novel stochastic optimal control methodologies that can be used to optimise decisions in situations with multiple uncertain variables and decisions (Tarnopolskaya, Chen and Bao, 2015; Chen et al, 2015; Langrené et al, 2015). The types of market uncertainties that can be considered include commodity prices, interest rates and exchange rate, while the key orebody uncertainties include the reserves, boundaries between ore types and even geometallurgical parameters.The dynamic decision support tools have a number of benefits and can be used to:construct optimal operational strategies and to optimally manage resources projectsgain insight into optimal strategies under different market conditions and project settings compare expected project values under different project settings and to select the setting that provides best sustainability outcomes.This extended abstract demonstrates the use and benefits of the dynamic decision support tools using a synthetic case study of a gold mine.CITATION:Chen, W, Langrené, N, Tarnopolskaya, T, Zhu, Z and Cooksey, M, 2016. Dynamic decisions under uncertainty – a case study on a gold mine, in Proceedings Life-of-Mine 2016 Conference, pp 20–23 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By D W. Airey

Frictional rock bolts are widely used because of their low cost. However, they have a thin wall section that makes them prone to corrosion, and they cannot be relied on to provide long-term ground support. It is difficult to assess the capacity after the bolts have been installed as they can only be pulled out if this has been allowed for during insertion. The questions of how long can the rock bolts function effectively and the effectiveness of various surface coatings, which can have significant cost implications are, investigated in this study.A series of accelerated corrosion tests have been performed on frictional rock bolts. The rock bolts, typically 900 mm long, have been inserted into concrete cylinders produced using a styrofoam insert to create the hole for the bolt insertion. Strata rock bolts with four surface coatings have been tested: uncoated black steel, galvanised, enduro (plastic coated) and coated with a proprietary aluminium/zinc alloy. Tests have been performed on two diameters of bolts. Following insertion of the bolts, the concrete cylinders were placed in a large drum filled with saltwater and current was applied to accelerate the corrosion process. The rock bolts were then extracted at various times after the commencement of corrosion. Comparison of the insertion and extraction resistances shows that corrosion initially increases the bolt resistance and that substantial section loss is required for the bolt resistance to drop significantly.CITATION:Airey, D W, 2014. Laboratory corrosion tests of frictional rock bolts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By K Koskinen, S Ronkainen

The flow field induced in an Outokumpu TankCell and by an OK rotor-stator mixing device in a laboratory and a process size flotation cell was modelled numerically using computational fluid dynamics (CFD). The primary target was to discover and reproduce the various interactions between the flow field and the flotation cell by numerical means. As power consumption depends sensitively on flow field, it can be regarded as a top-level derived quantity (or measure/metric) indicating the validity of the numerically obtained flow field. Having properly validated numerical means to produce the flow field the influence of various design parameters can be captured with certain accuracy. In addition, separate gas and solid phase models for bubbles and solids, respectively, were implemented. The comparisons between velocities and turbulence quantities measured using the laser doppler velocimetry (LDV) technique and CFD modelling were performed. The grid generation was performed with the commercial Gambit 1.3 and the subsequent integration and solving of the resulting algebraic equations with the commercial CFD-code Fluent 6.22. The computationally economic multiple reference frame method was included to model the moving rotor blades. Gas and solid phase models were modified mixture models.

Jan 1, 2005

At the Waikato North Head Ironsand operation, NZ Steel Mining Ltd is using a Bucket Wheel Excavator û shiftable conveyor mining system to excavate Titanomagnetite bearing sand and clay. The system utilises two Bucket Wheel Excavators with a two level shiftable bench conveyor and common trunk conveyor to deliver the material to a processing plant. The system was commissioned in November 1984 and has proved itself to be a high capacity, low cost method of excavating. Techniques of handling high sand faces have been developed and the conveyor layouts are going through a process of change to cope with the variable geo technical conditions and remain within: the characteristics of the excavators. The safety requirements for operating the system have been of a high standard and the experience has increased the confidence of the Company and the Mines Department Inspector's, for the first Bucket Wheel Excavator Mining system in New Zealand.

Jan 1, 1986

By P J. Hawke

Within the Mesa J pisolitic iron ore mine, clay is distributed unevenly throughout the deposit and often forms as pods and channels less than 10 m in width. The mine resource model, based on 50 m + 50 m spaced drilling, has been unable to accurately delineate the clay for scheduling and mining purposes. Therefore, alternative methods for mapping the clay-contaminated ore were sought. Predictive clay mapping will significantly reduce production costs at Mesa J through improved selective mining practices, more accurate scheduling, reduced wear on mining equipment and minimising the need for maintenance of haul roads and ramps. High lateral resolution electromagnetic (EM) surveying using a Geonics EM31 instrument can quickly and inexpensively delineate the extent and orientation of the clays. Preliminary results indicate that a block model based on the interpretation of the EM data can accurately predict the distribution, volume and tonnage of ore and waste material. While rip-line mapping, infill drilling, ground penetrating radar and gravity can delineate clay with various degrees of success, none were as efficient as EM31.

Jan 1, 2002

By T J. Napier-Munn

This paper proceeds from the premise that process improvement is a key part of the mineral engineer’s role, and one in which he/she can make a significant contribution to shareholder value. It presents four tools to help with process improvement projects. Two are designed for process monitoring, to determine as soon as possible whether there has been a true change in performance: the cumulative sum (cusum) control chart plot with V-mask, and the control chart using a process model. The other two are used for process optimisation: simplex self-directing evolutionary operation (SSDEVOP), and a response surface model developed using a central composite rotatable experimental design (CCRD). These methods are robust, have a rigorous theoretical basis and are easy to implement. They also promote project continuity which increases the chances of success, particularly in fly-in/fly-out (FIFO) operations. Variants are used in other industries, but they are rarely if ever applied in mineral processing to-day for reasons which are unclear. The paper gives examples of the application of each method in concentrators which demonstrate that they have the potential to be useful additions to the mineral engineer’s professional toolbox.CITATION:Napier-Munn, T J, 2014. Cunning solutions to process improvement, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 5–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By N N. Viswanathan, D Kumar, S Kumar

In secondary steelmaking, calcium treatment is practised to modify the solid alumina or spinel inclusions into liquid or partially liquid calcium aluminates. It has been seen that the dissolved calcium reacts with sulfur or oxygen present in the steel to form CaS or CaO type of transient inclusions. Post-calcium treatment these transient inclusions further react with pre-existing alumina or spinel inclusions and modify them. In addition, direct modification of pre-existing inclusions is also reported in the literature. In the present study, laboratory-scale induction furnace-based experiments are carried out to melt electrolytic iron in an alumina crucible followed by deoxidation with aluminium. The CaS-based composite material, prepared in-house, is added after the aluminium deoxidation to study the stability of CaS at the steelmaking temperature. Multiple steel samples were also taken to track the dissociation of CaS by means of sulfur pick-up in steel. Additionally, inclusion analysis of these steel samples was also performed to track changes in the chemical composition of inclusions in response to CaS addition. It has been seen that the CaS dissociates leading to a gradual pick-up of sulfur in steel. The scanning electron microscope – energy dispersive X-ray spectroscopy (SEM-EDS) analysis reveals that the alumina crucible and floated alumina inclusions are modified into calcium aluminates and the extent of modification depends on the contact time of CaS with the two sources of alumina mentioned earlier. However, the modification of alumina inclusions in the bulk steel did not occur during these experiments.

Jun 19, 2024

By J Krnmmelbein, T Raab

In Lusatia, lignite mining causes major disturbances on the landscape scale. Reclamation procedures are applied to recover the reconstructed landscape for different land use options. In this study we investigate soil physical properties of an agricultural reclamation/recultivation site directly after site restoration and the development of selected parameters within the first years after site restoration depending on varying recultivation strategies.The sandy substrates used for recultivation stem from depths of several meters. They are unstructured, free of recent organic matter and have high contents of calcium carbonate. During reconstruction and most of all during surface levelling with heavy crawlers, the substrate?undergoes high mechanical stresses. This leads to partly severe soil or substrate compaction, depending amongst others on substrate water content and mechanical stresses during site construction. We investigate the effect of different organic soil amendments, different crop rotations and partly subsoiling on the development of soil structure. We compare results of laboratory measurements directly after site construction before any reclamation measures had been applied to results we gained after three and four years of recultivation. The results show that after the earthworks are completed, the site is strongly heterogeneous in relation to mechanical stability, permeability for air and water, pore volume and bulk density. The results after three and four years show that the heterogeneity of soil physical parameters decreases. The selection of suitable crop rotations superimposes the affects of other reclamation measures, eg varying organic fertilisers or deep loosening.CITATION:Krnmmelbein, J and Raab, T, 2012. Reclaimed lignite mining areas A73 in Lusatia - Development of soil physical parameters of an agricultural site within the first years after site reconstruction, in Proceedings Life-of-Mine 2012 , pp 117-122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

There has been much debate in the past as to whether the Australasian Institute of Mining and Meteorology ("AusIMM") should issue valuation guidelines in addition to the ASX and NCSC requirements. My experience in preparing independent expert reports has been that "best practice" sets higher standards than any laws or requirements set out by the ASX and NCSC. This is where I see the AusIMM coming in.

Jan 1, 1989

By Hamilton LH, Campbell PB

Since fundamental research in applied coal petrography is carried out mostly on polished surfaces, backscattered electron microscopy is most applicable for studying coal in the SEM. By employing this technique coal macerals can be easily identified , and information on the relations between maceral groups, mineral matter and trace elements are highlighted by grey level contrasts. This type of information is valuable in coal technology and cannot by normally revealed by the light microscopy (e.g. the distribution of inherent mineral matter).

Jan 1, 1989

With the continuing move towards digital signal based control and measurement, it is inevitable that such technology will be increasingly employed on remote sites. The benefits of increased metallurgical performance, of reduced energy and manpower requirements far outweigh the problems associated with high technology in remote locations, provided that the installation is well thought out from both technical and manpower viewpoints. The new accessibility of vast quantities of process data will uncover previously unthought of savings and profit opportunities but brings with it the responsibility to carefully design the data presentation methods. The resulting changes in installed hardware will force changes in the maintenance and engineering workforce and will affect even the stores and purchasing department methods.

Jan 1, 1985

The commonly used stainless steels, their properties and uses are briefly discussed.Two specific topics are then explored in more detai's to highlight development areas, the potential of which has been largely unexploited in mining milling, refining and smelting operations. The high strength to weight ratios achievable in austenitic stainless steels has been widely used in the transport industry to design high integrity light weight vehicles,especially railway carriages. This use has rarely been extended into other structural areas where highly aggressive environments could make stainless steel a cost effective material compared to protected carbon steels. The recently developed weldable ferritic steels are described and their potential in materials handling discussed. Particular attention is paid to 3CR12, a nominal 12% Chromium, titanium stabilised steel finding wide acceptance in the mining industry.

Jan 1, 1985

By R M. Anderson, S P. Pigdon

The production of stabilised backfill at mine sites commonly uses Portland cement as the binder. Calcined gypsum has cementing properties and is cheaper to produce than cement. This paper discusses the strength of fills stabilised with calcined gypsum. Laboratory tests were carried out on specimens prepared from tailings obtained from four different sites to allow for the wide variety of tailings found in practice. The results show that the gypsum-based fills can achieve a strength of 1 MPa using around two and a half to four times the corresponding amount of cement.

Jan 1, 1998

By R Terracciano, J Schneider

Willemite (Zn2SiO4) is one of the main zinc carriers in several Neoproterozoic carbonate-hosted non-sulfide deposits ofNamibia and Zambia. Willemite commonly replaces sphalerite, but it may also replace the carbonate host rocks. Fluid inclusions, cathodoluminescence petrography and trace element geochemistry are crucial to distinguish between hypogene, high temperature and low temperature (possibly) supergene willemites. A global period of willemite mineralisation, extending from Cambrian to Lower Ordovician has been proposed for the southern hemisphere. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

A new engine family has been developed by Caterpillar Tractor Co. for application in off-highway trucks. This family, the 3500 Series is available in three configurations, covering a 600-1200 kilowatt range. This engine series incorporates the latest in design technology, stringent functional specifications for servicing ease, fuel economy, reliability, optimum performance and parts interchangeability. TECHNICAL INTRODUCTION The 3500 Series Engine has been under development by Caterpillar for over eight years and has undergone extensive testing in the laboratory and in field prototype units. - The engine configuration is a 600 Vee in 8, 12, and 16 cylinder versions. - The intermittent power output per cylinder is 75 kilowatt (100 HP). Net power for off-highway trucks is 600-1200 kilowatt (800-1600 Hp) depending on engine configurations. The 3512 (3500 Series Engine 12 cylinder Vee configuration) was the first model of the 3500 Series released. These engines offer optimum user value in terms of product durability, reliability, fuel consumption, performance and installation flexibility. Additional features of 3500

Jan 1, 1982

By Albinson T

Mexican epithermal deposits can be broadly grouped into two types based on their contained metals, distribution, associated igneous rocks and fluid inclusion compositions. Silver-gold deposits (e.g. Tayoltita) mostly occur in the western part of northern Mexico where host rocks consist of Eocene, intermediate composition volcanic and intrusive rocks; fluid inclusion studies indicate that mineralizing fluids were _10 eq. wt. % NaCl). The distribution of these two deposit types, crosscutting major major crustal sutures, and the close spatial-temporal relationships between mineralization and magmatism, together suggest that magmatic processes were more important in the formation of mineralizing solutions, as a source of both ligands and metals, than the segments of crust hosting deposits.

Jan 1, 1995

By K Kellett, A V. Metzner

From its discovery in 1845 ion exchange has continually improved technically to an extent where it is now in wide use commercially in many industries including mining and environmental. Purity Systems Inc. (PSI) has made advances in the development of metals capture materials such that metals recovery using the PSI patented technology is now a viable economic process for many previously rejected applications. PSI, in conjunction with Ammtec Limited, have developed cost effective advanced processes and systems.The presentation will introduce the chemistry behind the materials and its relevance to the chelation and ion exchange methods. The applicability of the PSI resin technology to copper, cobalt and nickel recovery and the engineered systems options available will be discussed as well as piloting at Titan Resources NL Radio Hill mine at Karratha in Western Australia.

Jan 1, 2002

By R Nakia, R Livingstone

Historically the Goldfields of Victoria produced large volumes of gold. Interest in these historical Goldfields has grown over recent years with a view to restarting production of gold. A notable example of this is the Bendigo Goldfield. There is also interest in the Ballarat Goldfield and Ballarat Goldfields Ballarat East Project is a particular example of this. The aim of this paper is to describe the ventilation aspects of the potential Ballarat East project. The mine is proposed as a decline access. The paper gives an overview of the project and in particular the ventilation planning associated with a number of possible equipment scenarios. The paper also analyses the main ventilation pollutants that are likely within the proposed mine as it develops to increasing depth. An attempt is also made to determine the depth at which mine climate will become the dominant pollutant rather than diesel exhaust pollutants.

Jan 1, 2003

By P Hayes, B Zhao

A range of materials are treated in zinc fuming processes to recover metal values and produce benign slag waste products. The selection of the optimum process conditions in these various technologies can be greatly assisted by the use of a chemical thermodynamic model of the system. In this paper the effects of slag chemistry on the liquidus temperatures, subliquidus phase equilibria and thermodynamic properties are described by a FACT model of the ZnO-PbO-FeO-Fe2O3-CaO-SiO2 system. In addition new experimental data on the effect of Al2O3 on the liquidus are presented. The implications of these findings for plant practice are discussed.

Jan 1, 2000