Search Documents

By Ohga K, Isobe T

Basing upon many and long practical experiences of gas drainage from coal seam and results investigations on the gas flow through in si-tu coal seam using tracer gases,it became clear that solid coal itself is hardly gas permeable or has extremely low gas permeability. Almost all of gas flows from a coal seam into boreholes through fracture net- works intersecting with them.Primary and secondary fractures in coal seams differ in their size and continuity from place to place according to differences of the coal strength and the stress conditions. A lot of gas can be drained through boreholes which intersect with many and/or wide fractures. A mathematical model for gas flow from a coal seam to a borehole through a discoidal fracture is proposed. From the numerical analyses,the apparent radius of the discoidal fracture in this model is shown to be a good indication of the gas drainage ratio. In addition to this,an atempt to make fractures around a borehole using high velocity water jet(ca.lmm dia.,300-700atm., 100-200 1/min.) is introduced.

Jan 1, 1982

By Royle A. G

The paper describes a geostatistical structural analysis of an 80 square mile lease of the Athabasca tar sands. Each step of the analysis is presented with the ultimate objective of condensing the principal structural characteristics of the chosen regionalised variables into the opera- tional form of the variogram model. The variogram model is then used to form kriged local and global estimates, with the corresponding estimation errors.

Jan 1, 1977

By Mousset-Jones P, McPherson M. J

This paper explains and discusses a computer program developed to deter- mine the optimum combination of fan pressures that will give a required distribution of airflows in a mine ven- tilation system. The program is based on an existing simulator, VNETPC and two experimentally developed relationships: (1) linearity between fan pressures and added regulator resistances and (2) a non- linear convex function relating the system air power and the fan operating Pressures.

Jan 1, 1988

Against a background of deeper pits, the introduction of prestripping fleets and the need for closer control of operating costs (especially the waste removal component), Australian coal operations utilising draglines have in recent years become increasingly focused on:1. assessment of more efficient excavation methods; and2. application of explosive products and initiation systems which offer more flexibility than ever before.Additionally, developments in blast performance assessment techniques and equipment, and computer modelling and excavation monitoring systems have provided an improved opportunity to design a blast to achieve a desired profile suited to the excavation equipment and Sequence.

Jan 1, 1992

The Mineral Resources Act 1989 was assented to on 25th October, 1989 after more than two years of consultation and negotiation between Government, the mining industry and other affected parties particularly the major rural organisations.The legislation proposes major conceptual changes in a number of areas and adopts a totally new approach to the definition of land and the mechanisms available to the mining industry for accessing such land.Unfortunately the passage of the legislation through Parliament coincided with the lead-up to the State election. Ultimately it became an election issue generating much adverse comment in the media particularly from rural and landholder groups. It was obvious that much of this anti-mining propaganda resulted from a lack of understanding of the legislation and the benefits that flow to the majority of landholders as well as the mining industry.It is essential that the contents of the Mineral Resources Act be thoroughly understood by all parties. Only then will all the State's resources be able to be developed in a multiple land use environment.This paper outlines the philosophy behind the new Act and the more important provisions contained therein.

Jan 1, 1990

By McAuley T. J

Computer software is an integral part of mining operations today with many sites using six or more software packages on a daily basis. However, the use of these different programs generates the need for substantial staff training. The current trend toward large integrated packages to solve this problem is counter-productive because the relatively small companies producing specialised mining software do not have the resources to develop quality software with all the required features. Software standards are being proposed by various parties but recent history indicates these will be unsuccessful. An alternative approach is suggested using the various standards which have been developed for the Windows operating system.

Jan 1, 1995

By Todd W, Stone C

A 3D graphics modelling system has been applied to longhole stope ring design at Z.C. Mines, Broken Hill, NSW. This has been in operation for a four month period (January, 1988). The purpose of this application was to provide computer assistance to mine planning engineers and blasthole design draftsmen for the longhole design process, particularly by: 1. reducing the- volume of tracing, drafting and geometric manipulation which is a significant feature of the manual design process, 2. providing additional design drawings to enhance the conception and implementation of stoping design.

Jan 1, 1988

In 1976, The Zinc Corporation Limited Broken Hill set up a plant to re-process a hill of tailing (Mt. Keast) from the original treatment operations. With the likely disappearance of this source of feed in 1985, an investigation was initiated to determine what other feed sources might be available. This involved searching through old records and photographs as well as a subsequent drilling campaign. The paper briefly covers the history of treatment operations and describes, as a result of the information obtained, the likely future sources of feed.

Jan 1, 1983

Geomechanics is one of the more specialised aspects of site supervision on a major tunnell- ing project. The controlled deformation of a rock mass as a result of tunnelling and the knowledge of loading of temporary and permanent underground supports are important for safe, economic construction. These basic parameters depend on the construction method and sequence and the geological conditions through which a tunnel is driven. Thus geomechanical monitoring during the construction phase provides feedback to a design team and allows any revisions to a design to cater for local conditions not revealed by earlier investigations. Detailed geological mapping is an integral part of geomechanics in the construction phase. It serves as a monitor on pre construction predictions and also forms part of the as- constructed record. If conventional excavation-techniques are adopted, geomechanics can provide a service of blast' vibration monitoring of surface structures in urban areas.

Jan 1, 1976

Martin Mining and Tunnelling Pty Ltd is a mining contractor with offices in Kalgoorlie, WA, Australia and Timmins, Ontario, Canada.Martin Mining and Tunnelling Pty Ltd offers services in mine contracting which include shaft raising, raise enlarging, excavation of rock passes and ventilating systems. It also offers the mining industry a unique mining method using the Alimak raise climber system.The Alimak raise climber system may be utilised in various types of orebodies, as the system is flexible to change. Sloping widths, drill hole patterns and changes in dip can all be accommodated with this method.This system allows for a highly productive, cost-efficient alternative to conventional longholing methods. This paper will focus on various aspects of the Alimak system which inherently make it a safe, viable method of ore extraction.

Jan 1, 1993

By Bezuidenhout M, Moolman D. W

In the minerals industry numerous problems cannot be solved by conventional mathematical models owing to their complexity or a lack of phenomenological understanding. Neural networks provide one way of mapping the ill-defined relations between process variables and functions for such ill-defined problems. Consequently, processes such as leaching and froth flotation are mostly controlled in an empirical way by using rules of thumb. In addition, these processes involve so many independent and dependent variables that the plant operator finds it difficult to visualise or even observe a change in process conditions. The structure of froths developed on the surfaces of industrial scale froth flotation cells has a significant effect on both the grade and recovery of valuable minerals in the concentrate. Although these effects are well known at the process operational level, where considerable heuristic knowledge is available, little work has been reported on a detailed characterisation of the mechanisms and the visual characteristics of the surface froth. Recent results from an on-line observation of froths in several plants have proved the relationships between image features representing froth behaviour and metallurgical results. It will be shown how supervised and unsupervised neural nets are being used on operating plants to interpret computer vision data. In froth flotation the operator is supposed to visually observe process changes from the appearance of the froth, which is an unreasonable demand under industrial conditions. The system described here determines textural parameters on-line, and tracks the changes in process conditions via a Self-Organising Map (SOM) neural net. This monitoring system warns the operator about fluctuations in reagent addition, and gives an idea of the type of froth encountered. In another example, changes in the mineralogical characteristics of gold ores are represented on an SOM map, based on the diagnostic leaching behaviour of such ores.

Jan 1, 1997

By M J. Saynor, W D. Erskine an, D R. Moliere

The Jabiluka uranium mine was constructed in the Ngarradj catchment, a right bank tributary of Magela Creek in the Northern Territory. The Jabiluka Mineral Lease is adjacent to Kakadu National Park, near an area listed as Wetlands of International Importance under the Ramsar Convention and recognised under the World Heritage Convention. In the late dry season of 1998 and prior to the 1998 - 1999 wet season, a stream-monitoring program was implemented in the Ngarradj catchment to collect baseline data on sediment transport within the catchment to assess and proactively manage associated impacts caused by mining at Jabiluka. Stream suspended mud concentration, stream discharge and rainfall data were collected for four wet seasons (1998 - 2002) giving an almost continuous data set. The stream system has high natural variability dependent on rainfall intensity and subsequent discharge and pre-wet season fire distribution and intensity. In general, mud concentration is elevated at the commencement of the wet season until about February. This is caused by first-flush removal of surface material detached during the dry season by agents such as bioturbation (including anthropogenic activity), wind erosion and surface desiccation. Water quality trigger values downstream of the mine were derived using upstream percentiles and the before-after-control-impact, paired site design. Both analyses showed no observable impact from mine construction in 1998 or during the study period. However, the impacts of dry season fires could be clearly detected. The data set provides good baseline information for future assessment at Jabiluka and demonstrates the need to view measured parameter values on a catchment-wide basis with knowledge of rainfall, discharge and fire distribution.

Jan 1, 2004

By B Bendtsen, L McQueen

The use of shotcrete as an efficient means of both temporary and permanent ground support has continued to grow over the last 30 years, with its use underground now commonplace around the world. However, the development of analytical design methods has lagged advances in material and application technologies. Historically, part of the reason for this was a lack of understanding of how shotcrete linings actually worked. Considerable progress has been made in this area in recent years and this paper attempts to summarise the current state of practice with respect to shotcrete lining design. It then concludes by summarising areas where the authors consider future research and development is still required.

Jan 1, 2008

The Olympic Dam deposit is located some 600 km north of Adelaide in South Australia. It was discovered in 1975 by Western Mining Corporation and in 1979 a joint venture was formed with British Petroleum for the evaluation and development of the project. Studies were completed and construction started in 1986 with the plant being commissioned progressively between April and August of 1988. In 1993 Western Mining acquired BP's interest and are now owners of the whole deposit. The scale of the initial development was 1.5 Mtpa of ore for the production of 45 000 tpa of copper cathode, 900 tpa of uranium oxide and some gold and silver. Two expansion programs have occurred in 1992 and 1995 and current performance is at the rate of 3 Mtpa of ore for the production of 84 000 tpa of copper cathode, 1500 tpa of uranium oxide, 24 000 oz per year of confined gold and 380 000 oz per year of confined silver (Table 1). An aerial view of the plant is shown in Figure 1. The benefit of diversifying into the production of more than one product is undoubted and the flexibility of being able to produce variable quantities of copper and uranium also allows advantage to be taken of a change in market conditions.

Jan 1, 1996

By Cairncross A. A

Papers on technical aspects of the Melbourne Underground Rail Loop project are being presented at this conference or have been presented previously or will be presented at other forums. This paper provides the framework for these papers by presenting the overall engineering tasks. The conceptual design, the special investigations undertaken, the management of the project and the construction development are highlighted.

Jan 1, 1981

The three systems of mining in use in the Southern Coalfield of New South Wales are bord and pillar with or without subsequent extrac- tion, longwall and shortwall. Bord and pillar with extraction is regarded as the conventional system. The application of continuous miners and powered roof supports (Shortwall) to coal min- ing has, grown in recent years from something of an oddity among extraction systems to an acceptable and viable approach in certain min- ing environments. The method can be applied in a high proportion of situations where normal pillar extraction is practised with advantages over the conventional approach. These advantages extend to both safety and efficiency aspects and also include better utilization of coal reserves. It holds hope for further gain in efficiency because its simplicity of layout lends itself to achieving the goal of contin- uous haulage towards which operators are always striving.

Jan 1, 1976

Today the application of computer programs for planning of mine-ventilation and for safety- analysis of ventilation systems is widespread practice in German mining. The computer program for network calculat- ion, developed at the "Mine Ventilation Testing Centre of the Westfalische Berggewerkschaft- skasse" allows the distribution of airflow and pressure in mines to be calculated. In a physically well founded manner it takes into account the natural ventilation as well as changes of volume-flow in the mine, which both are dependent on pressure and temperature. Compared to an incompressible treatment of the mine air these circumstances are of increasing importance with the increase of depth, air temperatures and fan-pressures'. This especial- ly holds for the calculation of airflows during failures of fans or for assessing the influence of open mine-fires on ventilation. The application of the program is very easy and its structure is made to fit the requirements of practice. For instance it takes into account the fan characteristics of all fans. For each planning calculated air- flows in all mine workings are compared to those of an eligible basic calculation or to measured airflows. In addition for the

Jan 1, 1983

By Lawson F

The Australasian Institute of Mining and Metallurgy is a society of engineers and scientists formed in 1893 (incorporated by Royal Charter in 1955) to advance science and engineering in the mineral industries, and to facilitate the exchange of information and ideas to enhance the professional excellence of its members. The Institute has several grades of members. The professional members are linked with Student and Company Members, as well as an Affiliate grade covering other professionals and non-professionals with experience in the mineral industry. The diverse group covers all sections of the mineral industry, from exploration through production to marketing of minerals and petroleum. Corporate (professional) membership also covers science and engineering professionals from specialisms other than the "traditional" ones in geosciences, mining and petroleum engineering and metallurgy. The Institute has Branches throughout Australia, New Zealand, Papua New Guinea and Oceania, whose activities complement the corporate occasions arranged for the benefit of all members by Headquarters in Melbourne. Members are drawn from all sections of the industry - private enterprise, government, research, education, and the support sector, including consultancies, manufacturers and suppliers. Membership of The Institute allows professionals to contribute to their profession through participation in The Institute's seminars and conferences, its many committees and Branch meetings, and through contribution to its many high standard publications. The Institute is the main body for the accreditation of professionals in the minerals industry. The activities of The Institute are directed towards the achievement of professional excellence. It provides opportunitites for contact with, and professional support from, colleagues, and the interchange of information on the latest industry developments.

Jan 1, 1989

By Duran A, Eggers M. J

It is standard practice in geotechnical studies for mine design to drill a series of inclined oriented boreholes into the proposed pit walls. However, this investigation tool is often used without an adequate understanding of the inherent shortcomings in the method and the many potential sources of error. Of the more commonly used orientation methods in Australia the clay imprint technique is probably the most reliable. Contoured stereographic plots of oriented core data are frequently characterised by diverse pole distributions and low concentration maximums compared with line mapping data. Common sources of error producing these poor results are misinterpretation of orientation marks or imprints, inaccurate marking of the reference line, errors in the structural measurement of the defects, lack of continuity information and blind zones sub-parallel to the borehole direction which correction methods frequently do not fix. Line mapping is the preferred method of structural data collection due to the lower overall cost, availability of continuity information and higher accuracy. The projectability of field mapping data to final wall positions can be assessed with a good understanding of the regional geology and local structural patterns. Where field mapping is not possible due to a thick regolith cover, core orientation should be carried out by experienced personnel to minimise the many potential errors.A series of case studies are presented which compare oriented core with mapping and highlight the inherent problems with the technique.

Jan 1, 1992

By Mowat BA, Leach TM

The Morobe Goldfield in Papua New Guinea has produced in excess of 120 tonnes of gold from predominantly alluvial sources. Hardrock gold has been mined historically at Wau (23t) and Edie Creek (40 and geological resources have been established at Hidden Valley (780, Kerimenge (360 and Hamata (30t). Numerous prospects have also been identified within the goldfield. Primary gold mineralisation is related to intrusion of dacitic to andesitic Edie Porphyry (2.4 to 3.8 Ma), often with associated diatremes, which have intruded along major regional structures. A full spectrum of deposit styles from proximal (mesothermal) to distal (epithermal) to the porphyry source is recognised. The transition between the proximal and distal styles is recognised both between deposits and within an individual deposit. The deposit styles should be termed porphyry related gold mineralisation rather than given the generic epithermal and mesothermal labels.

Jan 1, 1995