Search Documents

By Davies B, Rogers A, Grainger A, Todd J, Brenman R, Jones L, Horton B, Eager L

Research into the control of diesel particulates (DP) has been. conducted by BHP Coal for more than 7 years. Personal monitoring of employee exposures (n = 480 full shift samples) conducted at nine underground coal mines has indicated that the exposure of the workforce ranges from less than 0.1 to 2.2 mg/m3 of DP dependent on job type and mining operation. Approximately 50% of the mass of DP captured is elemental carbon (EC) which is the species currently being considered by some international regulatory authorities as the exposure standard. Five technologies for controlling DP were investigated in a combination of studies conducted in an above ground simulated tunnel, in a special controlled section of underground mine roadway and validated by application in standard coal mining operations at Tower Colliery. Tests conducted under controlled conditions indicate that dependent on the type of fuel in use, the introduction of low sulphur fuels can reduce DP levels in return airways by up to 50% and in actual mining situations a reduction of 20% can be achieved in exposure of the workforce. In addition, subjective responses from the workforce indicate that exhaust emissions from low sulphur fuels provide lower irritation and a more pleasant aroma. The use of water filled scrubber tanks reduces the level of DP emissions by 25%. Chemical decoking of engines resulted in a reduction of 20% in DP in return airways. A commercially available non-flammable disposable dry exhaust filter constructed from synthetic organic fibres with an operational lifetime in excess of 20 hours was found to reduce DP exhaust emissions by 80%. Investigations have indicated that the use of increased ventilation to control DP levels particularly in multiple vehicle situations does not follow a simple dilution factor and in some instances compliance with current regulatory requirements may not produce the required reduced exposure levels. The results from single component control strategies provide considerable reduction in exposure to DP, however the most efficient and cost effective control methodology is the use of a combination of individual systems modelled to operations conducted at each mine.

Jan 1, 1998

By J J. Plumb, P D. Franzmann

A study was conducted to describe the microbiology of the MICCL Monywa chalcocite heap bioleaching operation. Microorganisms were detected in the heap using culture-based techniques and cultureindependent PCR-DGGE analysis of the 16S rRNA gene. The metabolic requirements, temperature and pH optima were determined for selected strains isolated from the heap material. Six strains (BH1-BH6) were enriched and isolated from heap solids and leachate samples. Phylogenetic analysis of the 16S rRNA genes showed that strains BH3 and BH4 were closely related to the acidophilic bacterium Acidithiobacillus caldus and strains BH5 and BH6 were closely related to Leptospirillum ferriphilum. The optimum growth temperature for L. ferriphilum was 41.3¦C and the optimum pH range was 1.1 to 1.5. A new species of Archaea was isolated from the heap samples. Cells of the proposed species, Ferroplasma cyprexacervatum (æcyprusÆ L.n. meaning copper; æexacervoÆ L.v. meaning æto heap upÆ), are non-motile pleomorphic cocci, capable of chemomixotrophic growth with ferrous sulfate and yeast extract. Cells grow anaerobically on ferric iron in the presence of potassium tetrathionate and yeast extract as electron donors. Growth occurs from 14¦C to 63¦C, with an optimum temperature of 55.2¦C. The optimal pH for growth was 1.0 - 1.2. The species was phylogenetically most closely related to Ferroplasma acidiphilum with a 16S rRNA gene sequence similarity of 95 per cent. Molecular analysis of mine samples (16S rRNA PCR-DGGE) detected the above-mentioned cultured strains of microorganisms as well as species of Sulfobacillus and other unknown Proteobacteria. The microbial community of the Myanmar bioleach heaps contained similar levels of diversity to a dump bioleach operation in Chile, but contained greater amounts of biomass than another heap bioleach operation in Australia. The operating parameters of the Myanmar heaps (low pH and moderate temperature) have selected for the growth of moderately thermophilic microorganisms that are more commonly found in extremely low pH acidic mine drainage sites than in heap systems. The novel species of Ferroplasma is thought to be involved in the aerobic and anaerobic cycling of iron within the heap bioleaching environment.

Jan 1, 2004

By Langham B. M

A chemical study of the petrographic components of Greta (Maitland) coal, carried out by the Metropolitan Gas Co. (Melbourne), has revealed an anomaly in the composition of the durain which was thought to warrant petrological investigation.The original study, by the Metropolitan Gas Co., extended over eight shipments of coal received during the winter of 1943.The percentages of the several petrographic components were eslimated by careful handpicking of large samples of each shipment, and analyses were made of the handpicked components, which were also tested as to their gas-making and coking properties.The results are summarised in Tables 1 and 2. At first sight the components of the Greta coal bear a general resemblance in composition to those of other bituminous coals of similar rank, apart from a notable richness in volatiles, which is a distinctive feature of Greta coal. The durain has a typically higher ash content, and lower volatile content than the clarain (Table 1); and the coking behaviour of the four components is typical (Fig. 4).When, however, the analyses of Table 1 are re-calculated on a dry, ash-free basis, an anomaly appears: the clarain and the durain, on this 'pure coal' basis, have practically identical compositions, with the durain containing a slightly higher proportion of volatiles than the clarain (cf. Table 3); but the tar yield of these two components is very different (Table 1). Re-calculated on a dry, ash-free basis, the yield from the clarain is 18.9 gallons of tar per ton, while, that of the durain is 29.0 gallons per ton. The gas derived from the durain is correspondingly richer in illuminants (CH etc) and poorer in hydrogen than that from the clarain (Table 2), and is also notably richer in nitrogen.That the composition of the Greta durain is consistent is proved by the analyses of Table 3, in which the compositions of the respective durains and clarains of eight separate shipments of coal are compared. In most bituminous coals, the durain contains several per cent less volatile matter than the associated clarain, and high volatile content in a durain usually indicates a durain rich in spores.

Jan 1, 1947

At many locations in Australia the decommissioning of mining operations will require the disposal of excess water. If the water is contaminated its disposal may be restricted by government guidelines. The timing of water disposal may be critical to the schedule of close-out. The uncertainty of the annual rainfall input to the water storage and disposal system may determine the success or failure of close-out. The uncertainty associated with any outcome can be used to determine the reliability of the system, or inversely its risk. The technique of Monte Carlo simulation, using the uncertainty in annual rainfall, is applied to quantify the risks associated with water disposal as part of the requirements for close-out in two case studies. In both case studies it is assumed that water disposal is via evaporation only. The first case study is the Nabarlek operation, located about 270 km east of Darwin. This project is required to complete the engineering work associated with its close-out by December 1995. The second study investigates the situation of close-out for the Ranger Uranium Mine, about 250 km east of Darwin. It should be noted that the Ranger mine was examined as part of the annual update of its contingency rehabilitation plan and the probability of implementing the plan is extremely small. The probability of success for the Nabarlek case varied from less than ten per cent to greater than 95 per cent depending on the management strategy. Four possible strategies were investigated for the Ranger mine with the chance of success varying between 20 and 95 per cent. The estimation of the evaporation rate and the area allocated to evaporation was critical in both cases. By applying seasonally based evaporation pan coefficients determined on site, rather than an average monthly value of 0.75, the chance of success was improved by up to 35 per cent for Ranger. Simulation modelling is able to provide information on the likely response of mine water management systems and the level of risk. This information is required to efficiently plan and manage the disposal of water for close-out.

Jan 1, 1994

By A L. Hemphill

Conventional models, based on pulp kinetics, were regressed directly to steady-state data from a nine-stage platinum flotation plant, to provide a basis for optimisation studies. æFroth factorsÆ were used to characterise the froth in each stage and a ædepressant factorÆ was used for gangue minerals, to account for addition of depressant to the cleaners. These factors improved the fit, but differences between plant and model of up to 50 per cent were still present in a number of streams in the cleaning circuit. A new model was developed, which incorporated two rate constants for the recycle of particles from the froth. These parameters provided a workable approximation of the distribution of probabilities of particles being recycled in plant cells, depending upon where particles appeared at the surface. The feed streams were characterised by two pulp kinetic parameters and the above recycle parameters, for all minerals and all stages. The fit to the data was improved very significantly, when compared to the use of conventional pulp-based models with several pulp rate parameters. This relatively simple model did not require additional data from batch tests and it was suitable for plant simulations.Simulations of various strategies for plant operation were tested, allowing the simulator to vary the concentrate flows from all or some of the stages, in order to maximise platinum recovery. The simulator was imbedded in an automatic optimiser and constraints on chrome content or mass flow of final concentrate were used. The simulations of the existing circuits demonstrated that an improvement in recovery, (for a constant concentrate mass) of about 0.5 per cent was possible, by optimising all concentrate flows. A significant reduction in the flow of scavenger concentrate and an increase in the recycle flows in the cleaners were noted. The results of simulations of various changes to the circuit configuration are also discussed. An increase in recovery of 1.4 per cent (for constant concentrate mass) has been achieved in recent simulations, through circuit changes. However, it was necessary to keep the mass pull of concentrate, per unit area, within typical limits.

Jan 1, 2005

By M Araos, I Onederra

A novel explosive formulation that substitutes the use of ammonium nitrate (AN) with hydrogen peroxide (HP) as the main oxidising agent has been developed and tested as part of an Australian Coal Industry Research Program (ACARP) project. The main objective was to provide a step-change solution that has the potential to completely eliminate NOx fumes in blasting. The development of this HP/fuel-based explosive started with a comprehensive detonation characterisation program, consisting of unconfined velocity of detonation (VOD) measurements of samples at different diameters, densities and void sensitisation techniques. VOD results showed that the HP/fuel-based explosive mixtures behaved similarly to non-ideal commercial explosives; in that way mixtures could be tailored to achieve specific detonation performance targets. The next stage of testing in this development involved preliminary confined tests to evaluate the rock breakage potential of the HP/fuel-based explosive mixtures. Fully instrumented single-hole tests were conducted in a limestone quarry. Results from these preliminary trials confirmed the rock breakage performance of HP/fuel-based explosive mixtures. The confined VOD measured in one of the tests was 5100 m/s in a 102 mm diameter blasthole at a density of 0.96 g/ml. The corresponding borehole pressure measurement of this HP charge was 2.61 GPa with a detonation temperature of 2921°C. Based on near-field accelerations, both HP and ANFO charges displayed similar attenuation characteristics in the test conditions. Post-blast observations indicated that the breakage performance of the HP mixtures clearly reflected the in-hole detonation performance measurements obtained, confirming the ability of these explosive mixtures to both fragment and effectively displace the rock mass under evaluation. Further research work continues with the future commissioning of a prototype mixing and delivery unit, the successful completion and analysis of data from multiple-hole trials, and further characterisation work associated with product stability, reliability and performance under different geotechnical conditions.CITATION:Onederra, I and Araos, M, 2015. Detonation and breakage performance of a hydrogen peroxide-based explosive formulation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 565–574 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R Berry

This paper looks at two ways to estimate the bulk mineralogy of the rocks for assay intervals. The aim is to find an efficient indicator of the most common minerals in the rock. Phase (modal) analysis has traditionally been done using visual methods such as point counting and image analysis. A modern version of this process is the X-ray point counting routine using the SEM-EDS based software. These methods are too slow and expensive for routine analysis of bulk sample mineralogy at the normal assay spacing.Two sources of data were considered that provide information that can be used to determine the mineral abundance in assay samples. The most widely applied method is (semi-) quantitative X-ray diffraction (QXRD). The QXRD method is most applicable to major minerals and has limited application to minerals at low abundance. The nominal detection limit is 0.5 per cent. Values below five per cent have large errors. A second, less common, method is calculation of mineralogy from chemical assay data. Conversion of chemical analyses to mineralogical analyses depends on the unique chemical composition of each mineral. Elements only found in one mineral are easily accounted for, but many compositions are ambiguous. Deciding on the actual mineralogy is not simple. Recalculation of mineral mode from chemical analyses is more accurate than QXRD when the correct minerals, and mineral compositions, are known.Where only a few QXRD analyses are available they can be used to setup a protocol for calculation of mineralogy from assay data. Linear programming works well in this environment. The best results are obtained when both H2O and CO2 are directly measured. Loss-on-ignition (LOI) should be included if these are not available.Where both QXRD and chemical analysis are available for all samples, the best results are obtained using the least squared method to merge the data sets assuming QXRD has much higher analytical errors than chemical assays. The combined method provides more robust results because the high abundance minerals are controlled by the QXRD measurements while the chemical assays improve the precision for low abundance minerals

Sep 5, 2011

By H Holmstr÷m, A Widerlund, M Lindvall

At the Kristineberg mine in northern Sweden sulfide-rich, poorly buffered tailings have been deposited in five impoundments located along a valley. The tailings area has been remediated by applying a combination of till cover and flooding. A new method that has been applied to parts of the tailings area is to raise the groundwater table to saturate the tailings. By increasing pH by liming, thereby reducing metal mobility, a water-covered downstream impoundment is functioning as a trap for metals released from the till-covered impoundments upstream. In this paper the efficiency of the system approach used at Kristineberg is evaluated. Progressive changes of water quality from groundwater in the upstream till-covered impoundments via surface streams within the pond system to the water in the flooded downstream pond and its outlet are described. The results show that the system approach used in the design of the remediation programme of the tailings works as planned. The sulfide oxidation rate has decreased in the till-covered impoundments, and, as predicted, there is an out-flush of old weathering products which will continue for at least five years before equilibrium is reached. The groundwater in the till-covered impoundments has high concentrations of Fe, S, Mg and Zn, but the concentrations of metals such as Cu, Cd and Pb are much lower than before the till cover was applied. The limed pond is an efficient metal trap, with concentrations as high as 2.76 per cent Zn and 0.28 per cent Cu in the calcite-gypsum sludge developed on the tailings. The outlet from the flooded pond, and thus from the whole mining area, releases small amounts of metals to the recipient in comparison to the amounts that are in movement within the mining area. During the period May to November, 13 kg dissolved Zn and 111 kg particulate Zn was released to the recipient, whereas a total of 27 000 kg was transported by surface water within the impoundment system during the same period. The results from Kristineberg show that when planning remediation of complex mining areas, it is useful to adopt a system approach in which different methods are used on different parts of the area along the flow path of the drainage water, whereas flooding of the downstream pond is the key to the performance of the entire system.

Jan 1, 2003

By C G. Ferguson, S L. Makin

The Cawse nickel project is a new generation pressure acid leach (PAL), solvent extraction and electrowinning process used to produce LME grade nickel metal and cobalt sulphide concentrate containing 40 per cent cobalt by treating nickel and cobalt oxide ores from a lateritic ultramafic profile. The project is located 50 kilometres NW of Kalgoorlie in Western Australia. The commercial success of the Cawse nickel operation is dependent in part upon the ability of the principal ore type to be beneficiated. A simple process of rejecting lower grade material on the basis of particle size achieves this. The process is called upgrading and allows subgrade material to become commercial ore grade and also allows higher ore grades to be processed in the early parts of the operation. The success of the upgrade process is dependent upon the physical and chemical properties of the ore being processed and the nickel grade of the ore. The upgrade ore type represents >80 per cent of the Cawse nickel resource and is hosted mostly within a limonite unit, represented by goethitic clays in the upper saprolite zone. In the upgrade processing circuit the ore is crushed and slurried. It is then passed over a series of screens that remove all material over 0.5 mm. This ensures that coarse material is removed from the main ore stream. Upgrade is reliant on selectively rejecting lower grade or barren material, which can include silica, magnesite and relict saprock. To predict leach feedgrade, the grade control estimates the head grade and upgrade percentage for all ore delivered to the run of mine ore pad. To do this reverse circulation (RC) drill holes are logged for ore type, assayed for a range of elements and undergo simulated upgrade testwork. The percentage and grade of material rejected through the upgrade circuit has the most influence on upgrade per cent. This reject is determined by the physical properties of the rock mass and drum scrubber parameters. The correlation between nickel upgrade and reject can be established to predict upgrade from the known mass reject. Parcels of upgrade ore milled to date closely follow projected correlation trends. Upgrade circuit results have been excellent, with average nickel grades upgrading by 34 per cent, cobalt by 23 per cent, with 55 per cent mass passing.

Jan 1, 2000

By A R. Gerson

Pyrite, chalcopyrite and mixed sulfide samples, with and without quartz (5 wt per cent S), were subjected to column leaching to mimic natural weathering (cyclic wetting and drying). The pH and SO4 2- concentration of the column effluent was measured over a period of 78 weeks. The pH of the pyrite-only containing column rapidly decreased and remained under pH 4 after 12 weeks of leaching. The pH calculated assuming a 2:1 ratio of H + generation and SO4 2- release was slightly lower than that measured. However, a reduced H + to SO4 2- ratio of 1:1 is predicted if the release of aqueous Fe 2+ is assumed rather than the formation of Fe(OH)3. The pH of all columns containing only chalcopyrite or a 1:1 mole ratio of chalcopyrite and pyrite remained at or above pH 5 for the duration of the leach even though significant SO4 2- was released. One column containing the same initial surface area of pyrite and chalcopyrite but only approximately 0.10 the mole fraction of S as chalcopyrite maintained a pH of greater than five for the first 56 weeks of leaching and showed sporadic acid production thereafter. It is well established that oxidation of chalcopyrite results in a surface layer of polysulfide material. It is the formation of polysulfide that neutralises the acid produced on S oxidation through to SO4 2-. Hence where polysulfide formation occurs extensively on chalcopyrite the resulting solution pH decrease will be less than that based on SO4 2- production. The oxidation rate of sulfide minerals increases with decreasing pH and hence acid formation via sulfide oxidation to SO4 2- causes the subsequent oxidation rate to increase. The addition of calcite (CaCO3)to a pyrite column not only neutralises the acid formed but also decreases the rate of release of sulfate to solution by a factor of approximately 30. This is also the case where chalcopyrite is present mixed with pyrite. The rate of release of sulfate from the mixed sulfide mineral columns (after the initial release of the sulfate already present) was between one-fifth and one-tenth that in the absence of chalcopyrite.

Jan 1, 2003

By R R. Lovel

In this paper, life cycle assessment methodology has been used to assess the variations in water use associated with different metal production and processing routes and provide insights into the value derived from water usage in the minerals sector. Using water consumption data derived from the literature it has been shown that the æcradle-to-gateÆ water consumption (or embodied water) for production of the various metals considered in the study ranged from 2.9 m3/t for steel up to 252 087 m3/t for gold. The results largely reflect the grade of the initial ore used to produce each metal, and can be approximated by the following equation:W = 167.7 G - 0.9039 where: W = embodied water (m3/t refined metal) G = grade of ore used to produce metal (per cent metal) The study showed that indirect water consumption in the metal production life cycle, in particular that due to electricity generation, can make a significant contribution to the embodied water value, eg aluminium production. When expressed in terms of m3/t ore, the results for all metals considered indicated that the embodied water is roughly, on average, three times the water consumption of the mining and concentration stage. It was also shown that the economic value per m3 of water consumed for the minerals industry exceeds that for the agricultural and industrial sectors, supporting the view that allocating water resources to the minerals industry has a strong underlying economic basis. Water reforms currently taking place in Australia aim to address issues such as competition for water access, reduced security of supply and increase in cost. Consequently the minerals industry, along with others, can be expected to come under increasing pressure to reduce fresh or raw water use and to integrate water use across sectors. While water recycling is an obvious candidate to help reduce water consumption in the minerals industry, issues such as water quality, among others, will influence the extent to which this can be achieved. In addition, wastewater volumes can be minimised using techniques such as pinch analysis to establish and use the minimum water requirement for the process. The use of dry or near-dry processing technologies, for which the demand for water is small or zero, may be a more radical solution to the water consumption problem; however, it is possible that the introduction of dry processing would bring with it a new set of problems, including dust.

Jan 1, 2006

By S C. Dominy

Current and proposed methods of resource classification relate to the geological, economic and technical confidence in the estimated resource. Geological confidence is, however, only vaguely defined. It is largely related to the level of drilling and sampling, to the geologistÆs perceived level of confidence in his/her work and on the continuity of the mineralisation. Rarely has any real attempt been made to assess how well a deposit has been explored, sampled and evaluated and how accurate or realistic the geological model is for the deposit. This contribution reviews the impact of two of the potential sources of error, ie sample recovery and quality. The first of these parameters is measured during logging and assaying, but is often forgotten during grade and tonnage estimation, and resource classification. Preliminary studies have shown that modelling of this parameter is a valid exercise, which should accompany the evaluation of grade and other economic parameters. The sample recovery factor for an ore block can then be used to reassess the confidence in the block. It could, for example, downgrade the status of a Measured Resource to an Indicated Resource even though standard methods might indicate that the higher classification is applicable. A method is proposed by which this recovery factor could be incorporated into current resource classifications producing a more sophisticated and comprehensive measure of sample quality. A review of the sources of error naturally leads to the assignment of scores to each stage of the evaluation process, depending on the methods used and assumptions made. Sample recovery is one important factor, which is likely to appear at several stages. These scores can then be weighted and combined in a manner resembling that used in the CSIR Rock Mass Classification. This score will then allow the resource estimate to be rated on a scale from 0 to 100 per cent to produce a Quality Control Index (QCI). However, this index must then be modified using an Evaluation Difficulty Index (EDI), which reflects the difficulty of a particular style of mineralisation to accurate resource estimation. This results in the production of a Resource Reliability Rating (RRR), which can then be linked to international classifications, such as the 1999 JORC; 2000 CIM; and 2001 EURO codes. This will permit a more precise definition of geological confidence levels or, combined with estimation error, produce a classification system in its own right. This same rating can also be used as the basis for technical audits of mineral projects.

Jan 1, 2002

The link between exploration success and new ideas from research and development (R&D), although often assumed, is rarely well explained or well illustrated. One issue is understanding the role of innovative ideas in the exploration process, and another is determining the relative contributing factors to an exploration success. A useful measure of gold exploration success over an extended time period and geographic area is discovery rate (θ): Discovery rate θ = gold discovered/exploration expenditure (usefully expressed as tonnes of gold per $1 million). The total gold discovered is strongly leveraged to discovery rate, as any increase in θ typically has a positive effect on exploration expenditure. Hence, improving the discovery rate is a key driver for a sustainable mineral industry, especially for gold. There are very few ways to influence θ beyond innovative R&D ideas and breakthroughs, and well-motivated and trained staff. The Australian gold industry has experienced exceptional exploration success with 9956 tonnes of gold discovered from 1979 to 2003, inclusive. This equates to: Discovery rate θ = 0.9 t/A$1 M Two-thirds of this gold has been found in the Yilgarn craton of Western Australia (6265 tonnes Au). Without this exploration success, there would have been no platform on which to build the current gold industry and to take advantage of elevated gold prices and advances in mining and processing. Several causes of the Western Australian gold success have been proposed, and more than one may be correct. Gold price, and mining and processing advances have all had influence; but exploration success and discovery of gold were essential to add to the miniscule resource base of 1979. A comparison of the exploration methods used to search for gold in the Yilgarn craton in 1979, and 1990, highlights a small number of breakthrough ideas introduced to the industry during the 1980s, and in most cases emanating directly from local R&D. By the 1990s, these ideas were being used in most gold exploration programs in the Yilgarn craton, and are still used today. These six breakthroughs are: epigenetic timing of gold deposit formation (ie after formation of rock sequence), chemical and mechanical role of host rocks, relevance of carbonate alteration haloes, gold dispersion in the regolith, optimal sampling media, and appreciation of landforms in exploration program design. Interestingly, gold exploration science in Western Australia entered the 1980s period without rigid paradigms in place regarding gold deposit formation; there was a balance between descriptive and genetic models, there was scope to research gold deposits from microscopic to global scales and there were highly effective industry research uptake processes in place: it is suggested here that these favourable conditions contributed to the exploration success and industry growth.

Jan 1, 2007

By R Kahnt, S Jahn, D Baacke, M Eckart

Relocation into the Lichtenberg open pit mine of about 110 million m3 of sulfide-bearing and ARD-generating waste rock piled up on the surface is the most important and cost-intensive single surface restoration project conducted by WISMUT GmbH at the former Ronneburg uranium mining site. The waste rock comprises for the most part Palaeozoic shales, limestones and diabases with pyrite contents of up to seven per cent. Waste pile relocation began in 1992 and is scheduled to be completed by 2007. The approach used for relocation has been extensively described elsewhere (Jakubick et al, 1997; Hockley et al, 1997; Chapman et al, 1998; Paul, 2003). Following completion of the backfill that will be up to 60 m above the initial ground level, a dry cover will be placed on top of the backfilled mine wastes. The area to be covered amounts to about 220 ha. Design planning for the final cover placement of which is to begin in 2004 had to be based on a comprehensive cost-benefit analysis over and above compliance with legal requirements. The crucial question to be answered in this respect was to determine û in addition to the expenditure required to ensure reuse, radiation protection and soil protection û the extent to which additional time, effort and money were justified in order to minimise contaminant release from the unsaturated portion of the backfilled pit contributing to total releases into the ground water and possibly achieve savings in long-term operating costs for the on-site water treatment plant. Optimisation was based on contaminant balance modelling for the entire site reproducing dominant physical and geochemical processes. Among the specifics underlying the cover design is that contaminant release from the backfilled open pit must not be considered independently of that from the adjacent flooded underground mine and that a major part of the backfilled open pit will also be submerged. Following weighing of cover-related short- and long-term costs it was found that higher construction costs for the various cover options will not be offset by cost savings in the long-term water treatment. As a consequence of pit flooding, even a costly multiple cover including an impermeable layer will only insignificantly impact on concentrations and loads at ground water spill over points. As a result of comprehensive studies and investigations, a combined cover of cohesive soil material from on-site excavation overlain by a 0.4 m thick storage layer to restore natural soil functions for revegetation was derived and submitted for approval. Together with hydraulic measures, this approach is to meet any requirement in terms of radiology, water protection, stability, erosion protection, and reuse.

Jan 1, 2003

By R Williams, P Kohout, J Comins

The Northside Storage Tunnel (NST) is the largest tunnelling project ever undertaken in Sydney. The tunnel extends deep underground from the western bank of the Lane Cove river to the North Head sewage treatment plant (STP), with a branch tunnel from Scotts Creek connecting to the main tunnel under Tunks Park. The aim of the tunnel is to intercept wet weather overflows from four key points along the northernsuburbs ocean outfall sewer (NSOOS) and provide short-term storage and transfer of sewage to NorthHead STP for treatment prior to discharge to the ocean through the deep ocean outfall. The project was an ambitious undertaking by an alliance between the client Sydney WaterCorporationand the engineering firms of Montgomery Watson, Connell Wagner and Transfield to design andconstruct approximately 20 kilometres of tunnel, tunnel declines and shafts in just over three years. In order to achieve this tight timeframe construction of the NST has been undertaken simultaneously at seven construction sites located across the northern suburbs of Sydney. As with most tunnelling operations, tunnel boring machines (TBMÆs) and roadheaders dominated the excavation activities. Tunks Park and North Head STP are the major tunnelling sites. An access decline was excavated using roadheaders at both of these sites to facilitate tunnelling using TBMÆs. Three TBMÆs 3.8 m, 6.0 m and 6.3 m diameter) were launched from Tunks Park and one TBM (6.5 m diameter) was launched from North Head. At the overflow interception sites of Scotts Creek, Lane Cove River and Quakers Hat Bay two vertical shafts known as drop and access/ventilation shafts were constructed. These shafts would provide the linkage between the existing sewer and the tunnel. As their names suggest the drop shaft would convey the wet weather sewage overflows to the tunnel while the access/ventilation shaft would provide access during dry weather and ventilation during a filling event. The fourth overflow site of Tunks Park would use the tunnel decline as its link to the tunnel. Originally these shafts were to be excavated using the raise bore method. This technique however, is entirely dependent on the TBMÆs reaching the shaft locations at the specified time. This was not the case at two of the three shaft excavation locations and top down methods of excavation such as, a percussive cone fracturing (PCF), blind bore, mechanical excavation and drill and blast were investigated to ensure the project met its completion schedule. Traditionally project decisions are dominated by cost and schedule objectives. The contractual arrangement of the Alliance however, required that the objectives of safety, community and environment also be considered in any decision making process. Thus each of these top down methods of excavation were assessed against these five objectives. On considering all of these factors the use of explosives was considered to be the superior technique.

Jan 1, 2001

By R B. Wanty

Historically, most investigations of biogeochemical cycling in acid rock drainage systems involved synoptic sampling over longer time periods (one sample per week or month) or intensive time series studies over a few hours or days. However, many important episodic loading events, such as seasonal meltwater and storm events occur on timescales that are rarely observed by these traditional sampling approaches. Monitoring these transient processes, which may contribute the bulk of the annual metal loading, is essential for accurate assessment in acid rock drainage areas. Recent work also has demonstrated dramatic diel (24 hour cycle) variations in trace metal concentrations in response to diel changes in temperature, pH, oxygen, and photochemical cycling (Brick and Moore, 1996; Nimick et al, in prep). To characterise a system that may respond to diel, seasonal, and episodic events, a monitoring program must sample at a frequency that captures the details of these major forcing events. We developed two novel instruments, the Zn-DigiScan and the DigiSampler to examine low and high frequency temporal changes in acid rock drainage areas. The Zn-DigiScan is a battery powered real time in situ chemical analyser designed for long-term deployments with hourly analyses of Zn. Stream physical parameters (temperature, conductivity, dissolved oxygen, pH, turbidity, etc) were measured every 15 minutes with a water quality sonde. The DigiSampler was developed for the long-term daily sampling of biogeochemically active elements and can take either discrete samples or samples integrated over 24 hours. The DigiSampler collects 2 ml samples in a Teflon coil which are separated by 0.2 ml nitrogen bubbles. The sample coil is returned to lab and the 2 ml samples are diluted 1:10 and analysed for trace metals by ICP-MS. Initial results from a three-day deployment at Fisher Creek, MT, USA have successfully demonstrated the ability of the Zn-DigiScan to record Zn concentrations at levels below 100 ¦g/L. Zinc concentrations measured at 30 minute intervals in Fisher Creek showed a diel cycle with low values of ~25 ¦g/L in the late afternoon and increasing to ~60 ¦g/L by early morning. Zn concentrations were inversely related to temperature and pH, suggesting that temperature and pH dependent adsorption was the main factor controlling diel Zn fluctuations. Initial deployment of the DigiSampler also was successful, revealing diel cycles in Zn, Cu, and Mn. Comparison of trace metal samples collected by the DigiSampler showed good agreement with samples collected by an Isco automated water sampler, demonstrating that the DigiSampler can collect clean samples for trace metal analysis at the low ¦g/L range.

Jan 1, 2003

The Kelian gold mine which was developed in East Kalimantan Indonesia in 1990 - 1992 is scheduled to complete mining and processing operations in 2004. This will have a major impact on the neighbouring communities who have benefited from the jobs, economic activity and infrastructure development which has been generated by the mine. Currently, there are no formal regulations or standards specifying the procedures for relinquishment of mining leases in Indonesia. Furthermore, a move towards regional autonomy, providing greater authority and responsibility to local (regional) areas, has recently been implemented in Indonesia and limited capacity exists in the new regional governments. Consequently, in October 2000, Kelian Equatorial Mining (KEM) initiated a partnership with the local community and government to explore sustainable post-closure options for the mine site and community development programs. The Kelian mine closure strategy seeks full involvement of all stakeholders through the Kelian Mine Closure Steering Committee (MCSC) in the development of sustainable solutions which will enable communities to secure long-term benefits and minimise post-closure risks from the KEM operations. This organisation, jointly chaired by the Head (Bupati) of the regional West Kutai government and the KEM President Director, with representatives from the local communities, governments and NGOs, has developed a Charter, a website and evaluation criteria to ensure accountability and transparency. There are four technical working groups, consisting of representatives from the mine, local community leaders, NGOs, Universities, Local, Provincial and Central Government Departments, which report to the Steering Committee. These working groups have researched, developed and recommended sustainable options to the Steering Committee. The MCSC has met quarterly to examine options in accordance with the criteria set out in the Charter and has endorsed sustainable solutions which have support from Government, Community and the mine. This paper describes the closure risks, sustainable outcomes derived through the Kelian mine closure steering committee process and outlines the methodologies used to develop and endorse sustainable solutions in a society with limited capacity undergoing enormous change and uncertainty.

Jan 1, 2003

By D Craw

The Macraes gold deposit is located in a low angle NE dipping (~15¦) shear zone, the Hyde Macraes Shear Zone (HMSZ) cutting greenschist facies metasediments of the Otago Schist. The shear zone is host to large volumes of mineralised schist and relatively sparse quartz veins. Early in the development of this through going shear the schist experienced an episode of hydro fracturing and fluid redistribution. As a result, presently exposed schists within the Intrashear sequence are pervaded by localised swarms of quartz filled pure extension and extensional shear fractures hosting goldscheelite mineralization. The swarms comprise networks or æstockworksÆ of veins that strike NE, are subvertical and form subperpendicular to the shear zone fabric. Vein frequency across strike is typically ~1 m-1, with most veins five to ten centimetres thick and vertically continuous for up to ~20 m. Many of the veins show delicately banded internal textures that are parallel to the vein margins. These bands/lamina indicate incremental growth and are defined by a variation in grain size or alternatively by thin slivers of wallrock schist, though typically uncommon. The majority of veins are overprinted by a weak plastic deformation, although primary structures are largely preserved. This deformation has produced subgrain structures, migration of grain boundaries with sutured margins and undulose extinction of grains. These microstructural observations possibly indicate that temperatures were around 300¦C during stockwork vein formation. In general, the mode of brittle failure that developed the stockwork veins can be directly related to lithological variation. The geometry of stockwork veins indicate that local vertical shortening and extension occurred in the Intrashear sequence of the HMSZ synkinematically with thrusting. Localised extension was mainly parallel to the structural trend; that is, it took place perpendicular to the direction of inferred thrusting. The development of lateral ramps most likely gave rise to extension in parts of the shear zone during continuous shortening to form swarms of stockwork veins.

Jan 1, 2004

By P Waters, P Hollings, M Baker, D R. Cooke

Over the last three million years, porphyry and epithermal mineralisation in the Baguio Mineral District has been driven by calc-alkaline magmatism associated with the subduction of the South China Sea plate and the Scarborough seamounts beneath northern Luzon, Philippines. Coupled with extreme uplift and exhumation rates, mineralisation in the Baguio District has been responsible for the emplacement of over 922 million grams of gold. As one of the oldest intrusive bodies associated with the Baguio District, the Black Mountain Cu-Au deposit consists of at least five intrusive phases overprinted by potassic and propylitic alteration and sulfide mineralisation. Gold ore grades are low and molybdenum grades high with respect to other porphyry Cu-Au deposits in the Baguio Mineral District. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By J Finlay, P Betts, D Milton, H Williams

The aim of this paper is to present an innovative method to help delineate potential target volumes for haematite-goethite mineralisation as opposed to more magnetic ores. This is achieved through interpretation and modelling (2.5D and 3D inversions) of ground magnetics and gravity surveys over the Koolanooka South prospect in Western Australia. The targets are assumed to be dense and weakly magnetic and hosted within banded iron formation (BIF) horizons. Geophysical interpretation (2D map) was performed using a variety of processed magnetic and gravity images (Betts et al, 2007) to determine the distribution of lithologies, to understand the structural architecture and to map out any anomalous areas of excess density (possibly indicating goethite alteration). The created geological map is used to build geological cross-sections (geometrically consistent) that were modelled (in 2.5 D) against both potential field datasets. The crosssections are consequently used as the framework to build a 3D geological model. The model defines 3D volumes of rocks including several BIF horizons. The distribution of densities and magnetic susceptibilities of the BIFs is inverted within the GOCAD«-VPmg environment to reduce the misfit between the response of the model and the observed gravity and magnetics. By combining the results of both petrophysical property distribution it is possible to map out (using classical GIS type queries in 3D) volumes of higher density and lower magnetic susceptibility.

Jan 1, 2009