Search Documents

The following paper outlines the types of employment immediately available to graduates following their university degree, a discussion on mine manager requirements, mentions career advancement and time frames to achieve this as well as providing some key information regarding student vacation work. The author hopes to educate present graduates, as well as inform students of characteristics to develop the most opportunities in life.

Jan 1, 2006

By A Riles

"Three issues of relevance in a modern tailings storage facility (TSF) are:geotechnical stabilitymanaging acid rock drainage (ARD) from pyritic tailingsmanaging the tailings from cyanidation of gold ores. Drawing on examples from both copper porphyry flotation and sulfide-hosted gold ores, this paper demonstrates that giving some weight and importance to the process tails properties upfront can influence the flow sheet and not only improve tailings management effectiveness but also impact positively on economics. In the case of a typical copper porphyry ore with moderate pyrite content, the rougher tail in a conventional high pH selective flotation step is usually classified as potentially acid generating (PAG). To avoid the generation of ARD within the tailings and the requirement for a costly plastic lining, subaqueous deposition is recommended, which in turn has negative implications for tailings stability, consolidation and closure. Adopting a neutral pH rougher stage rejects silicate gangue but recovers pyritic material to the cleaners for a subsequent selective flotation stage, often after regrinding. This effectively quarantines the PAG pyritic material in a much lower volume cleaner tail, which can then be appropriately encapsulated within a larger non-lined flotation tails facility. It also facilitates cyanide leaching of the cleaner tail for gold recovery, with the encapsulated tailings facility being suitable for cyanidation tails storage. A case study from Europe is examined. For gold ores where the gold is sulfide-hosted, but not refractory, a flotation route with cyanidation of the concentrate can similarly produce the majority of tailings as a benign flotation tail and again quarantine the low volume concentrate leach tail in a small encapsulated cell with appropriate residual cyanide management measures applied. Overall economics for intensive leaching of a low volume concentrate stream can also be surprisingly positive. A feasibility study design example of the process and TSF is presented. CITATION: Riles, A, 2016. An Integrated Approach to Optimising All Concentrator Products, Including Tailings, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 341–346 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By P Dowd, A Adeli, C Xu, X Emery

Geometallurgical modelling is increasingly being incorporated into mineral resource modelling and estimation as a means of increasing efficiency, decreasing operating costs and reducing risk in mining operations. Traditional geostatistical workflows for geometallurgical modelling face several difficulties, in particular, related to the non-additivity of process response variables, to highly heterotopic data sets and/or to preferential sampling designs, all of which may explain why most attempts to estimate geometallurgical response variables from assay data and mineralogy are still based on statistics and machine learning. The aim of the work presented here is to demonstrate the applicability of geostatistics to estimate copper recovery from copper sulfide ores at the Prominent Hill Iron Oxide Copper-Gold (IOCG) deposit in Australia. As recovery is non-additive, the preferred workflow is the joint estimation of the masses of metal in the feed and in the concentrate, both of which are additive variables. While the mass of metal in the feed can be estimated from abundant online assay analyses, the mass of metal in the concentrate can only be estimated from a very limited number of laboratory-scale batch flotation tests. Traditional approaches to estimating the masses of metal in the feed and in the concentrate, such as simple and ordinary co-kriging, are described and discussed. A modified version of co-kriging is introduced, which incorporates linear relationships between the mean values of the input variables, in addition to a spatial correlation model. Co-kriging with related means is shown to outperform traditional simple and ordinary co-kriging in terms of precision, accuracy and consistency of the estimates, and offers a practical and efficient tool to deal with highly heterotopic and preferential sampling designs.

May 24, 2023

By B Chapman, B Gaida, L Drowley

The 372 MW Ulu Jelai Hydroelectric Project is a peaking power scheme located in the Cameron Highlands, Malaysia. The main features of the project include an 84 m high roller compacted concrete dam; two weirs which divert flows from adjacent catchments via transfer tunnels into the main reservoir; an underground power waterway; and an underground power station complex comprising three large caverns with connecting tunnels approximately 240 m below surface level. The project includes approximately 25 km of tunnels excavated in fresh granite rock mass with some distinct shear zones of weaker material. The majority of the tunnels are being excavated using drill and blast, with the two transfer tunnels being excavated with a tunnel boring machine (TBM).This paper focuses on the design and construction of the Telanok underground power station complex and also some aspects of the design for the headrace tunnel. Topics covered include geological site investigations including in situ measurements of rock stresses; development of a geological model and parameters for rock support design; three-dimensional modelling to assess interactions between the caverns to optimise rock support; design of a rock anchored crane beam; construction of the caverns and design of the unlined headrace tunnel taking into account hydraulic jacking and operational pressure fluctuations.CITATION:Drowley, L, Gaida, B and Chapman, B, 2014. Design and construction of large caverns in granite – Ulu Jelai Hydroelectric Project, Malaysia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 361–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By R J. Thompson

In truck-based hauling systems, the mine haul road network is a critical and vital component of the production process. As such, underperformance of a haul road will impact immediately on mine productivity and costs. Operations safety, productivity and equipment longevity are all dependent on well-designed, constructed and maintained haul roads. With the advent of autonomous haul trucks, the haul road itself becomes all the more critical to the success of these type of operations; not only in relation to mine operators requirements for safer and more efficient and predictable haulage systems, but also in response to autonomous truck manufacturers’ requirements for a more predictable and controlled operating environment. This paper presents a brief summary of the state-of-the-art in surface mine road design and then proceeds to examine the design and technological challenges associated providing a safe, predictable and affordable road for autonomous mine haul trucks. The paper serves as a basis for evaluating the contributions that enhancements in road design and management can deliver to autonomous mining operations, an initiative that also has scope for adoption within the operating life of many mines, haul roads and haul trucks.

Nov 22, 2011

By S Graskoski

The allocation of boggers and trucks at Telfer’s sublevel cave mine is currently assigned by manual techniques, with decision-making primarily dependant on the judgement of the operators and mine control. Field observations indicate that allocation decisions could be improved by establishing a systematic approach to dispatch. An investigation into the current state of technology determined that no currently available solution would provide a tool to make optimal decisions for the Telfer dispatch challenge.In an underground sublevel cave (SLC) environment, the destination decision is fixed and the source is variable, so open pit and block cave solutions are not relevant. Newcrest underwent a development venture with an external vendor to develop a novel production dispatch algorithm and user-friendly software program to make allocation decisions in a systematic way with consideration given for the true complexity of the operation.This new production software, nicknamed Dingo (for Dispatch ‘n’ Go), is a smart way to assist forepersons and mine control operators in their day-to-day roles of planning shifts and allocating trucks and loaders to optimal locations during shifts.CITATION:S Graskoski, 2017. Dingo – an optimisation tool to solve complex short interval control at Telfer underground mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 261–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By C A. Foss, K Leslie, C Arnold

Magnetic susceptibility measurements provide rapid, non-destructive testing of drill core, but cannot directly map magnetite and/or hematite content. Combined magnetic susceptibility and magnetisation measurements provide much more diagnostic information and, with sparse calibration constraints, are able to quantify magnetite and hematite concentrations and potentially map differences in grain size and texture. We have developed a travelling three-component vector magnetometer that can be run alongside core to map its external magnetic field. The logger has been designed to operate in core sheds and at remote drill sites. It is used to rapidly scan a length of core, with each core being scanned in different rotations. The magnetic field contributions from any remanent magnetisation rotates with the core and cause differences between successive measurements, while the field contributions from any induced magnetisations with isotropic magnetic susceptibility remain constant. Deconvolution of the magnetic field data with simultaneous three-channel inversions of the multirotation data separates remanent and induced components. Interpretation of this data provides estimates of the intensities of induced and remanent magnetisations, the orientation of the remanent magnetisations and the ratios of the induced and remanent magnetisation strengths. We expect these magnetisation parameters to correlate with stratigraphy through a banded-iron formation. Furthermore, we anticipate that we will be able to use this information to map zones of oxidation and other changes along the core. This novel instrument is one component of an integrated CSIRO program to provide new capabilities for iron ore exploration and development based on studies of magnetic fields and magnetisations at scales ranging from centimetres for these core investigations to tens of kilometres for formation studies.CITATION:Foss, C A, Leslie, K and Arnold, C, 2015. Rapid logging of different magnetic phases in banded ironstones using a travelling three-component vector magnetometer, in Proceedings Iron Ore 2015, pp 271–276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By R Dunne

"Continuous improvement on metallurgical treatment plants is possible only when good data and analysis of the data are available. Good data implies appropriate and accurate mass measurement coupled with good sampling practices and accurate chemical analysis especially when carrying out monthly metallurgical metal reconciliations. Adequate characterisation of key samples (eg tailings, feed, concentrates and others) at timely intervals is an important part of a good continuous improvement program. The data from this will help identify opportunities to improve operation performance and thus profitability. Examples are provided of projects that have led to improved plant performance based on good metallurgical data collection and analysis.Citation:Dunne, R, 2016. Using Metallurgical Data to Drive Continuous Improvement, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By S Hayton

While coal seam gas is considered to be an unconventional gas, the proliferation of areas under exploration and development mean that it is rapidly becoming main stream. The potential of New Zealand's coals to produce coal seam gas has been recognised for some time. However, key market drivers have not been suitable for the progression of this potential into reality. Kenham Holdings Ltd and CRL Energy Ltd, recognising the potential for the gas in New Zealand have initiated what is the largest ever assessment of New Zealand's coal seam gas potential. The premature demise of the giant Maui field has raised the focus of new gas developments and has increased interest in what we are doing. Over the past couple of years Kenham Holdings Ltd and CRL Energy Ltd have approached the assessment of the coal seam gas potential in a staged programme. Preliminary assessment of the data on the permit areas indicates that the potential resource may be up to 500 PJ. To date, preliminary appraisals have been completed or are underway on a significant number of fields. Exploratory drilling has been completed or initiated on several of those fields, with results from this work being fed into the preliminary modelling as it has become available. Given that in many of these areas there is no pre-existing information concerning their gas potential and world wide experience with lignite is practically nonexistent, it has been a steep learning curve with many surprises. However, initial gas content results and preliminary gas flow models have been on the whole, rather pleasing, with the commerciality of some developments already apparent.

Jan 1, 2003

By A D. Strand

The Coeur dÆAlene mining district in northern Idaho, USA is the second largest producer of silver in the world. The Proterozoic Revett Formation hosts most of the mesothermal Ag-Pb-Zn vein ore in the district; it consists of informally designated lower, middle, and upper members. All three members show up to an order of magnitude of southward thickening across the regionally significant Osburn fault. Changes in thickness of the Revett Formation across the Osburn fault reflect a major, down-to-the-south, crustal-scale fault that:was active during sedimentation, was periodically reactivated during the structural and metallogenic history of the district, and likely provided first-order control over regional fluid flow during mineralization events. Where vein structures intersect favourable strata, they produce rich ore; where vein structures cross unfavourable strata, they are poorly mineralised or barren. The most favourable host rock in the district is quartzite, which accounts for the large production from the quartzite-rich Revett Formation.The district has five main types of hydrothermal alteration:feldspar destruction, hydrothermal bleaching, carbonatisation, sulfidation, and silicification. Feldspar destruction is the most extensive and pervasive type of alteration, involving the district-wide absence of feldspar from Belt Supergroup rocks. Hydrothermal bleaching results from the destruction of hematite; it forms alteration envelopes that extend for tens to hundreds of metres into the wall rocks around many of the mineralised veins. Siderite alteration is most diagnostic of mineralisation, forming alteration envelopes that extend for tens to hundreds of metres into the wall rocks around all mineralised veins. Fine-grained arsenopyrite and/or fine-grained pyrite commonly form alteration zones adjacent to high-grade ore shoots that extend for metres to tens of metres into the wall rocks. Widespread silicification is most easily recognised by the presence of numerous quartz veins.

Jan 1, 2002

By B Beale

Bow-tie analysis is a commonly used tool to identify and display risks that have the potential for an undesired hazardous event. The output of the analysis are bow-tie diagrams, which are an effective and versatile communication format that can be applied to any type of risk. Contrary to their simplicity, a proper bow-tie diagram that maintains its usefulness and clear communication is difficult to build. Over two decades assisting Major Hazard Facilities with bow-tie analysis for Safety Cases, several common mistakes have been identified. This paper aims to highlight those issues with examples and provide improvement strategies. A sample of the most common mistakes are: - overly complicated risk analysis - poorly scoped and defined terms - poor descriptions and justifications - identifying too many dependent controls. Overly complicated risk analysis leads to wasted time in obtaining data for little gain. The bow-tie diagram is only a model. Effort should be redirected into identifying and managing controls that will make a tangible difference to site risk. Broad scopes lead to enormous and confusing bow-tie diagrams for both the user and the workshop team. Defining the scope of the study, the consequence severity of interest and critical control characteristics creates focused workshops and targeted analysis. With more definitive scope, there may be more bow-tie diagrams, however, they are succinct and specific. Well described causes are imperative for clear communication to users, regulators and future bowtie review workshop groups. It is best to use common wording structures and explain the event stepby- step. Also, clearly document any likelihood calculations and use data references where applicable. Identifying all possible controls creates a false sense of security that there are many layers of protection. In reality, most controls are dependent on a single system or person and could all be compromised from a single failure. A definition of a ‘bow-tie’ control is required whereby it must be independent from other controls. Improving the bow-tie analysis process will assist operators in developing meaningful and ‘operational’ bow-tie diagrams to support risk management systems and practices.

Apr 16, 2024

By R Talebi

A research project to better understand the rock mass behaviour and the seismic response has been conducted during the design and construction of the 9215 level at the E-Block sector of the Northern Star Kanowna Belle Mine. The research program was undertaken at a tunnel located 1100 m below the surface with the results applicable to feasibility studies on underground mining projects in highstress conditions, where failure can occur very soon after tunnel construction. Semi-circular excavation shapes coupled with the use of de-stress blasting techniques were designed to monitor the excavation in conditions of very high stress. The ground support was designed considering high energy dissipation ground support schemes (HED) as described by Arcaro et al (2021). The results indicate a decreased rock mass demand due to the change of excavation shape. Also, localised reduction in rock mass stiffness was achieved due to the implementation of de-stress blasting. Finally, increased ground support capacity was gained by the implementation of the high energy dissipation ground support schemes. The Kanowna Belle Mine has significant ore reserves at depths exceeding 1000 m below the surface. The results of this research will be used to optimise the extraction of the remaining E Stoping Block at depths exceeding 1350 m.

Mar 29, 2023

By M K. C Roberts, M G. Magwaza, J W. L Hanekom, P Piper, R Lousteau

Due to the perceived potential to extract the second economic manganese seam at its Black Rock Operations in the Northern Cape Province, South Africa, Assmang commissioned an investigation with respect to mining method and sequencing of the two orebodies in 2007. Based on this initial study into multiseam potential, conditions and impacts, the rock engineering aspect was expanded to determine conceptual rules to govern the extraction of both manganese seams using the normal bord-and-pillar layout implemented at this operation. This work included the theoretical analysis using basic pillar design practices and numerical modelling, including the use of Map3D, UDEC and Phase2 codes.In 2013, Assmang launched a large-scale investigation into the potential to increase mine output from all possible manganese sources at the operation. Included in this investigation was the requirement to confirm or modify the conceptual multiseam extraction rules to implementation. As part of this confirmation process, stress measurements, borehole camera audits and additional numerical modelling were performed at a particular site on the operation where a limited extraction of both seams had been undertaken. The results obtained from this process provided confidence in the conceptual extraction rules and allowed the derivation of final extraction rules that will be implemented at the operation as the multiseam mining process becomes more widespread.CITATION:Hanekom, J W L, Roberts, M K C, Magwaza, M G, Lousteau, R and Piper, P, 2014. Confirmation of multiseam extraction rules for Black Rock Manganese Operations, Assmang, Northern Cape, South Africa, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 107–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By R Winterberg

Concrete is a well established and reliable construction material for the permanent lining of tunnels, but shows some weak performance characteristics, which can be overcome by the addition of specialised fibre reinforcement. This paper addresses the particular performance design requirements of segmental linings, discussing the improvements of fi bres on concrete properties. Focus is made on the beneficial effects of fibre reinforcement on the cracking behaviour and the toughness performance, providing a safe and durable tunnel lining.Not only the mechanical performance of fibre reinforced concrete (FRC) for segmental linings, but also the durability of the linings has gained growing attention among the designers and consultants. Especially tunnel linings with exposure to media with corrosion potential, such as wastewater sewer tunnels or desalination plant outfall tunnels, have high requirements on their durability. The design of these structures must provide a comprehensive study of durability aspects. Fibre reinforcement can substantially improve the durability of concrete.Research has been carried out on the cracking behaviour of concrete. The beneficial effects of steel fibres on the cracking behaviour reduce the permeability by reducing the flow paths within the concrete. Crack bridging steel fibres create necking effects in bending cracks, leading to earlier closure of the cracks. Further, steel fibres create particular crack formations, which lead to a substantial reduction of the fl ow rates through separation cracks. The results also show that considerable cost savings can be achieved using FRC, as the thickness of the linings can be reduced.The durability design issues will be addressed and underlined by a case history on the Hobson Bay sewer tunnel in Auckland, New Zealand.

Mar 8, 2011

By N Johansson, D Johansson, A Beyglou, H Schunnesson

As demand for optimisation of mining processes increases, more attention is drawn to blast performance and fragmentation improvement. Fractures and discontinuities are among the most influential factors in blast results, therefore one of the initial steps towards blast optimisation is to gather information about the rock mass and integrate it in blast design. This paper presents a method for assessment of rock mass discontinuities and integrating it in production blasts in the Aitik open pit copper mine in Sweden.3D photogrammetric techniques were utilised to map discontinuities and distinguish domains of similar geologic structures in the pit. As a pilot study for a future campaign, four different initiation directions were tested through six pilot blasts in one of the domains. The results were compared in terms of swell and loading efficiency of rope shovels to identify the correlation between blast performance and initiation direction compared to major discontinuity families.It was established that in the trial domain, blasts initiated towards north or north-west yielded larger swell and better performance of loading. Comparing these blasts with discontinuity families show that there is a correlation between blast performance and initiation direction according to the dip and strike of these discontinuities. Such knowledge can be used for future blasts in the same domain to increase long-term operational efficiency through slight modifications in drill pattern and initiation design.CITATION:Beyglou, A, Schunnesson, H, Johansson, D and Johansson, N, 2015. Adjusting initiation direction to domains of rock mass discontinuities in Aitik open pit mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 385–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S L. Simpson, J Waworuntu, B M. Angel

"The Batu Hijau copper/gold mine, operated by PT Newmont Nusa Tenggara, is located in the south-western part of Sumbawa Island, Indonesia, and is situated ~10 km from the south coast at an altitude of ~450 m above sea level. The mine became fully operational by year 2000 and processes approximately 120 000 t of ore per day that contain an average of 0.53 per cent copper and 0.4 per tonne (g/t) gold. Tailings management at the mine includes a deep-sea tailings placement (DSTP) system that discharges tailings through a pipeline via an outfall located at a depth of 125 m at the head of the submarine Senunu Canyon (Figure 1).The environmental impact assessment undertaken prior to approval of the DSTP evaluated both on-land tailings storage facility (TSF) and DSTP options for tailings management. Negative attributes of the on-land TSF included removal of approximately 2300 ha of forest/agricultural land, the potential relocation of >2000 people from their communities, the high average annual rainfall (>2500 mm) and potential for earthquakes presenting challenges for water management and creating a long-term risk of failure. The final choice and Indonesian Government’s approval of DSTP was also influenced by the close proximity of the deep submarine canyon to the mine. The Batu Hijau mine is one of the larger examples of DSTP in the world and deposits tailings at the greatest depth. The depth of the main canyon increases to >2000 m within 20 km of the coast, and to >3000 m approximately 50 km from the coast.The DTSP at Batu Hijau must comply with an environment management plan (EMP) and environment monitoring plan of permit stipulation that approved its commencement in 2000; updated in 2010 and 2015. The environmental management objectives were to avoid impacts to highly productive components of the ecosystem such as coral reefs, mangroves, surface waters and fisheries, and confinement of impacts to areas of low biological productivity. In the vicinity of the DSTP outfall and within the Senunu Canyon, the management plan predicted significant adverse impacts from the DSTP on the marine ecosystem in the form of: reduction in sea water quality due to elevated turbidity and dissolved copper concentrations burial of benthic organisms a reduced habitat for demersal fish.Recovery of the pelagic and benthic ecosystem to preoperating conditions was predicted to occur within the first two years after operations cease. The CSIRO has performed due diligence studies to independently verify compliance with permits and evaluate new monitoring objectives (Apte et al, 2004; Simpson et al, 2010; Angel et al, 2015), and has performed assessments of environmental monitoring data on the tailings footprint and ore stockpile processing against the above environmental objectives (Simpson and Angel, 2015).CITATION:Angel, B M, Simpson, S L and Waworuntu, J, 2016. Long-term monitoring and targeted assessments to improve management of mine wastes – the Batu Hijau project, in Proceedings Life-of-Mine 2016 Conference, pp 81–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

A laminar-flow furnace technique was used to study the combustion of 37-53 µm size fraction of Woodlawn copper concentrate containing 7.4 per cent zinc, 5.0 per cent lead and 22.5 per cent copper. Factors studied included the effect of time, temperature and the distribution of volatile elements between the panicles and the fume. Air was used for most of the work but a few tests were carried out using 1 per cent oxygen in nitrogen. Chemical analysis, X-ray diffraction, and scanning electron and optical microscopy of polished sections were used to characterize the reaction products.When the concentrate was combusted at low temperatures (800-900°C), the fume was rich in lead. At higher temperatures, this was diluled by increasing amounts of zinc and copper. 70 per cent of the zinc, 60 per cent of the lead and 40 per cent of the copper were found in the fume after oxidation at 1400°C. Lead, zinc and copper were present in the fume as anglesite (PbSO4), zincite (ZnO) and cuprite (Cu2O) respectively. The major phases present in the panicles were magnetite (Fe3O4) and/or cuprospinel (CuFe2O4), with some zincite and cuprite.Elemental copper was found in the particles oxidized in 1 per cent oxygen. Possible vapour species responsible for the vaporization are discussed.

Jan 1, 1985

The HYC mineral deposit at McArthur River is about 1.5 kilometres long by 1.0 kilometres wide and 55 metres thick, and contains 227 000 000 tonnes of ore of average grade 9.2% Zn, 4.1% Pb and 41 g/t Ag. Major studies have been carried out continuously since 1955 over the deposit and in the general region. This work is continuing. A small underground mine was developed by driving a decline tunnel to intersect the mineralization 80m below the surface. This provided a fully representative sample of the total deposit unaffected by weathering or oxidation, and was available for the major test program carried out in a pilot plant built to determine the full metallurgical charac- teristics of the ore. The pilot plant operations followed investigations by research institutions, both in Australia and overseas, into the problems of this ultra-fine grained ore. The ultra-fine grained nature of the ore required grinding to an average size of 95% passing 37 micro metres or 400 Tyler mesh. A major feasibility and environmental report was submitted to the government covering all aspects of a development program. The geological, engineering, metal- lurgical, economic, cultural and environmental submissions contained in this report were studied by external consult- ants employed by the government, who agreed with the conclusions that the McArthur HYC deposit is at present Uneconomic.

Jan 1, 1984

The paper describes the studies conducted to date on the short term adsorption/desorption of gases in coal from the point of view of developing techniques to predict imminent outbursting conditions in coal mines. A number of different parameters such as'dP express, K' and AV 0/60 etc. which have been effectively used overseas were studied on samples of coal from Westcliff and Leichhardt Colliery. Results indicate that these do not seem to be valid indices for predicting an outbursting condition. Based upon desorption isotherms, a new index defined as "L" has been developed which shows promising results. This index is in a position to differentiate the changes in the structures of coal and its proness to outbursts. The "LZ value determinations and its usefulness opens a new field where it would be possible to determine outbursting conditions from existing drill cores obtained during exploration studies or from long holes drilled in advance from underground workings. The index is more or less independent of the time elapsed between the extraction of a sample and the conduct of the test. The test for "L" can be conducted'on site or in the laboratory. The test is simple, easy to carry out and the "L" value for a sample can be calculated in less than 20 minutes. It could be adapted as a routine test for monitoring outburst conditions in mines.

Jan 1, 1980

Mt Todd lies towards the south end of the Pine Creek Geosyncline, sandwiched between the Cullen Batholith and the Edith Falls Basin, in an area of regionally metamorphosed sandstones, siltstones and shales. The Batman deposit, some 3 km west of Mt Todd is a sheeted quartz vein system hosted within greywackes of the Palaeoproterozoic Burrell Creek Formation (Finniss River Group). The gold-bearing quartz veins, trending 010¦-020¦ and dipping 60¦-70¦E, are commonly 0.5 to 5 cm wide and occur at intervals which are from 10 cm to 1 m apart. Gold tends to be restricted to the quartz veinlets and immediately adjacent country rock. Grade Control utilises two 4 m 'collar' samples which are collected from each 8 m production blasthole. The irregular distribution of the quartz veins and erratic gold mineralisation has resulted in a disseminated 'salt and pepper' type of gold occurrence, with only a poorly defined footwall. Delineation of ore and waste blocks for mining uses an approach which combines the smoothing effect of kriging with a pragmatic view of the raw data. Large ore blocks with simple geometry help to minimise mining dilution, reduce block variance and give good reconciliations to interpreted ore tonnes and grade. Daily mine face advance is reported against truck counts and provides continual comparison with budgeted production. All data processing uses Gemcom software, together with Lotus spreadsheets.

Jan 1, 1994