Search Documents

By P Marlow

Raiseboring is an attractive method of constructing shafts, being safe, fast and comparatively cheap. But this means back-reaming through weathered ground. However in the gravels and weathered near-surface rocks typical of the Western Australian goldfields, back reaming large diameter shafts through to the surface is risky and conventional sinking from surface has normally been required.An alternative construction approach has recently been used to stabilise the weak surficial materials and allow raiseboring through to the surface. The method is based on first installing rings of non-contiguous reinforced bored piles around the shaft perimeter, for temporary support, then back reaming shafts at full diameter through to the surface. Immediately after the reaming head is removed, the weak exposed materials are supported using remotely sprayed fibrecrete.The method has been successfully applied to four shafts since July 2007; 3 m and 4 m diameter shafts at Trident Mine, a 3 m diameter shaft at Wattle Dam and a 4.5 m diameter shaft at Athena Mine.Bored pile layout designs have varied from eight to 24 piles, of diameters 120 to 270 mm, in one or two rings. In one case, the top 10 m of the proposed shaft was pregrouted. Subsequent surveys have confirmed that fallout occurred in some shafts, out to the ring of piles, implying that the piles inhibited collapse.The practical implementation of the method was not always easy and many valuable lessons have been learnt. This paper documents key aspects of the method and the critical elements for its application.

Mar 21, 2011

By P Edmondson, S Narendranathan, S Setchell

The complexities of mining in current economic conditions, where ore extraction schedules are varied on a weekly basis so as to ensure constant supply to the process plant, can result in a number of scenarios that pose geotechnical challenges. This paper presents a case study where alterations in the mining schedule of a particular mine resulted in the necessity to mine under a large uncompacted embankment, ie integrated tailings and mine waste landform. To effectively ensure that ore recovery was maximised, a well-designed slope monitoring system to evaluate design performance and to provide timely warning of impending failures was imperative. In order for an appropriate slope monitoring strategy to be developed, a thorough understanding of the potential slope failure mechanisms, capabilities and limitations of available monitoring techniques is required. Communication of the monitoring results and response strategy to alarms generated by monitoring systems must also be carefully considered to maximise effectiveness. The results of preliminary stability modelling can be used to guide the design of a monitoring system, which in turn can then generate data which can be used to iteratively refine the geotechnical model. This paper illustrates the development and implementation of a slope monitoring system and associated communication system, using a case study developed at a large iron ore open pit mine in the Pilbara region of Western Australia.CITATION:Narendranathan, S, Lee, E C, Setchell, S and Edmondson, P, 2015. Modelling of an integrated waste storage facility, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 183–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By M Dusci, A Trueman, S Poos, R Baumgartner, M Brittan

The Canahuire epithermal Au-Cu-Ag deposit in southern Peru is a complex and challenging deposit for metallurgical studies. It has issues of gold locking in sulfides and non-sulfides, deleterious elements and acid rock drainage (ARD). From scoping study to feasibility study, there has been considerable improvement in the understanding of the important geometallurgical characteristics that need to be measured and modelled. This paper presents the current understanding and the requirements to continue to provide optimal models for mining studies.Significant effort has been put into understanding the genesis of the deposit. Improved spatial and temporal understanding of lithology, alteration, structure and mineralogy was used to build a geological and alteration model of the deposit.Early metallurgical programs quantified the effect of head grade on process plant recoveries, but the geometallurgical and statistical analyses did not identify other physical characteristics that influence these recoveries. The studies improved the understanding of the nature of locked gold which can occur as minute inclusions (< 5 ¦m) in sulfides (primarily pyrite with lesser arsenopyrite, pyrite being 100 times more abundant than arsenopyrite) and gangue minerals (quartz and carbonates) as well as solid solution in arsenopyrite and pyrite.The presence of pyrite and the limited buffering capacity of waste rocks increases the potential ARD, which will require mitigation costs before, during and after operations. Waste rock ARD potential has been classified and incorporated in the geometallurgical model. The current classification of waste rock at Canahuire, using international classification standards, is limited due to the complexity of the deposit.Complex deposit metallurgy necessitates a complex process flow sheet, including flotation and cyanidation. Economic recovery will be constrained by the relationships between economic variable grade, other elements and mineralogy. These constraints and inter-relationships are difficult to establish throughout the deposit with a single test. A follow-up geometallurgical program is under investigation and will attempt, with the help of additional test work, to map areas of higher and lower recoveries. It is hoped that metallurgical response can be linked to measurable parameters other than head grade. If this is possible, these factors can be incorporated into future geometallurgical models.CITATION:Baumgartner, R, Dusci, M, Trueman, A, Brittan, M and Poos, S, 2013. Building a geometallurgical model for the Canahuire Epithermal Au-Cu-Ag Deposit, Southern Peru - past, present and future, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 51-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By A Fyans, B Ghahreman-Nejad

This paper discusses the method and results of an options study into selection of the optimal form for a 130 m high tailings/water retaining dam, located in a region of high seismicity in central Iran. The proposed dam is part of a planned expansion project for Sarcheshmeh Copper Mine (SCM), which after construction will provide 550 million tonnes of additional tailings storage over the next 27 years. Geotechnical investigation at the proposed site indicated that adequate suitable low permeability materials (i.e. clay) were not available in the immediate vicinity of the dam site and would need to be imported from a distance of well over 10 km (direct). Given the magnitude of the estimated quantity of material and construction cost it was considered prudent to compare the cost of alternative dam design options for the proposed storage. A total of five dam design options are considered including a conventional rockfill embankment dam with an upstream sloping earth core (ECRD), a geomembrane face rockfill embankment dam (GFRD), a sloping asphalt core rockfill embankment dam (ACRD), a roller compacted concrete dam (RCCD), and a filter rockfill embankment dam for tailings storage together with a separate smaller earthfill core rockfill dam (ECRD) located downstream for storage of decant water. The risks, costing and design of all options are discussed in detail and the outcome of the study is presented.CITATION:Ghahreman-Nejad, B and Fyans, A, 2018. Optimum embankment design for a tailings dam, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 427–438 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By T A. J Hopper, S Mukkisa, K-O Ott, D Palmer

RIG Technologies has developed new technology that can successfully acquire high quality natural gamma ray (GR) and hole deviations, downhole while drilling, on reverse circulation drills. This technology survives the hostile downhole environment with shocks of between 400–2500 g for 7– 10 days at a time. The Logging While Drilling (LWD) service eliminates the need to run in-rod surveys, either by the driller or by wireline trucks and crews. This time saving is in the middle of the drilling process, thus enabling drills to keep drilling and increase their productivity. Additional to the natural GR and directional survey, the downhole tool is equipped with sensors to measure the downhole dynamic response of the drilling system providing insights into rock hardness, density and potentially clay types. These parameters have never been acquired behind the hammer before and coupled with surface measurements from the drills themselves, form a rich data set for trainable machine learning algorithms shortening the time to receive advanced geophysical answer products from sometimes months, to live feeds directly from drills (Hopper, 2019). Alive, high speed, two-way data link between surface data acquisition systems and downhole geophysics tools has been established and incorporates calibrated surface measurements of dynamic forces directly on the drill string to match up with those measured downhole. Receiving live streams of natural GR and hole deviation surveys as the drill is drilling allows true remote decisionmaking with live data available anywhere in the world. The combined data from surface and downhole dynamics builds a data set that could begin to enable true optimisation of autonomous drilling processes.

Nov 8, 2021

By J Light

Since 2019, the mine planning team at Olympic Dam has been establishing and maturing a shift from deterministic to probabilistic scheduling techniques. This paper outlines this journey undertaken by the mine planning team, key learnings from implementation and further work required to increase the level of planning maturity. Olympic Dam (OD) is a highly variable, polymetallic orebody with a vertically integrated value chain from operations to final product. The processing plant has a tight set of quality constraints which are managed through timing of stopes from varying parts of the orebody. Value is eroded for the operation when forecasted quality of the mine feed encounters disruptions from unplanned changes to the timing of stope starts. As production has moved from the historic Northern Mining Area into the more geologically complex Southern Mining Area, average stope size has reduced, resulting in increased mining fronts required to meet production targets. This has created a problem of increased schedule complexity and difficulties in identifying and communicating resource priorities within a large set of individual stope critical paths. The problem was approached by considering each stope as an individual project constructed by teams working across multiple projects at any one time. The operation could then be considered a multi-project environment with shared resources and enables the application of Critical Chain Project Management (CCPM) to the mine plan. Key to CCPM is the addition of time buffers to protect the critical path of a project form upstream or downstream processes. Implementation of time buffers protects the stope start date against compliance to plan variance. The monitoring of each time buffer consumption, as a proportion of total construction activities completed enables proactive prioritisation of resources. This resulted in an increase in the number of stopes starting in accordance with the mine plan, simplified communication of priorities to all levels of the operation, increased compliance to plan and a clear measure of schedule risk during planning routines.

Mar 29, 2023

By K L. Brown

The concentrations of trace metals in deep hydrothermal solutions (~1 km depth, 200 to >300¦C) from modern hydrothermal systems in the Taupo Volcanic Zone, New Zealand, and Ladolam, Lihir Island, Papua New Guinea were obtained using a purpose-built downhole fluid sampler and ICP-MS analyses. The results range widely: gold (<0.1 - 23 ppb); silver (<3 - 2400 ppb); arsenic (100 - 18 000 ppm); antimony (2 - 1200 ppm); mercury (<1 - 78 ppb) and provide the basis for quantifying the flux and fate of metals as well as assessing their sources (Simmons and Brown, 2006, 2007). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By W Lunwongsa, S Meffre, S Nuanla-ong, K Zaw, R James, A Salam

Gold and silver mineralisation at the Chatree low sulfidation deposit is hosted in andesitic volcanic and volcaniclastic rocks and characterised by multiple hydrothermal alteration assemblages and quartz-carbonate (chlorite-adularia) replacements, veins and breccias. The ore-bearing veins are influenced by intersecting structures and host rock lithologies. Emplacement of the host succession occurred at 250 ¦ 6 Ma (dated with laser ablation ICP-MS U-Pb zircon techniques), which was closely followed by mineralisation at 250.9 ¦ 0.8 Ma based on the analysis of adularia from coarse-grained quartz-sulfide (chalcopyrite-pyrite- sphalerite) veins using laser ablation Ar-Ar methods. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By R Varden

This paper summarises the process taken to simplify 35 ground support standards accounting for the multiple development profiles, dynamic geotechnical environment and the practical safety implications of a large-scale change in the ground control standards. This reduction was required after an incident involving incorrect standards being issued. The subsequent investigation identified that: • Selection of ground support standard for a mining instruction (MI) is not straightforward due to multiple standards, standards not reflecting current reinforcement used and complex geotechnical environment being encountered. Instead, site-specific ground control instructions were being issued. • Ground support standards were hard to follow and confusing, errors were present and not all standards to scale. • Ground support standards being used did not reflect what was being installed, ie bolt type incorrect and mesh orientation different. • No process or tier action response plan (TARP) for operators to follow for ground control standard noncompliance. • No justification for ground support standards being used in the current geotechnical environment. • No process for ground support standard selection and thereby no paper trail to document and assess adequacy of performance. A project was undertaken to reduce and simplify the ground support standards, produce a justification document to support ground support design and develop a process for site practitioners to identify the type of ground support standard required for the mining instruction. The exercise of rationalising the ground support was met with some challenges, including: • Technical aspects to determine the level of demand and the capacity for each ground support scheme. • Training the geotechnical engineers how to determine the level of risk for each area. • Winning over other technical services staff and the underground mining contractor of the new approach and then implementation. One of the major successes was the acceptance by the underground operators who found the system simplified their work and gave them increased confidence in management of seismicity. The rationalised ground support standards have now been successfully in place for over two years.

Mar 29, 2023

By D Willis, A Shanahan, C Jacobs, T Luxner

The application of tunnel boring machines (TBM) for reef mining is a unique practice with benefits over current mining methods given the right geology and geometry of the orebody. The Stillwater Mining Company (SMC) of Nye, Montana, USA operates two mines for obtaining platinum metals. The operation is currently using a 5.5 m diameter open-type machine for further mine development, as well as another TBM that they own.The latest 7.1 km bored tunnel, known as the Blitz Tunnel, will be routed parallel to the ore deposit in igneous mafic intrusive rock, and will be used for the life of the mine operation. It will be used to map the ore deposit, and provide a rail haulage route.Detecting the reef in relation to the TBM requires careful analysis. Diamond core drilling occurs ahead, above, and alongside the machine at every 150 m. The core is drilled, logged, and interpreted on the spot, concurrent with boring. Based on the data, the TBM is readjusted so that it stays on the correct bore path.This paper will highlight the application and benefits of TBM usage for reef mining, with detailed descriptions from the mine site.CITATION:Willis, D, Jacobs, C, Luxner, T and Shanahan, A, 2014. Tunnel boring machine usage speeds up development at Stillwater Mine, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 683–690 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M Campbell, A Jeffcoate, J-C Vannay, B Perriaux

Phyllite waste rock at the Simandou Pic de Fon and Oueleba Iron Ore deposits (Guinea, West Africa) variably weather to form clay-rich rocks. This weathering modifies the mineralogical, geochemical and mechanical properties of the phyllites. Final pit walls will largely be formed in phyllite, so it is critical that the slope design takes account of the distribution and variability of weathering within this material. Phyllite intact material strength has been correlated with geochemistry (ie mineralogy) facilitating the establishment of domains of intact rock strength (IRS). In order to calibrate this geochemically-based strength model, core from diamond drilling (DD), comprising a variety of phyllite material types (from soft clay to moderate strength rock), was geotechnically logged to assess intact strength; further validation was achieved by uniaxial compression (UCS) testing and point load tests (PLT). The correlation between geochemistry and strength offers a potentially powerful tool for differentiating basic mechanical properties of the rock mass, especially at Simandou where a significant proportion of the resource drilling is done by reverse circulation (RC). Unlike DD, reliable measurements of material strength from RC samples can prove difficult, especially in clay-rich material. Therefore, gaining information from routine geochemical assay results, independent of the sampleÆs physical integrity, is a valuable and cost-effective source of reliable empirical data. Data acquired using this approach provides an opportunity to develop strength domains, which are integrated into mine planning block models. In combination with other geotechnical characteristics, this can be a valuable input to the development of geotechnical models. This technique has allowed spatially representative rock strength data to be derived and offers the potential for optimising pit slope angles in areas where hitherto conservative design criteria had been assumed.CITATION:Jeffcoate, A, Campbell, M, Vannay, J-C and Perriaux, B, 2013. Modelling intact rock strength of clay-rich rocks with geochemistry at the Simandou iron ore deposit, Guinea, West Africa, in Proceedings Iron Ore 2013 , pp 193-202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By L D. Munro, S A. Jackson

This paper provides a logical approach to developing a TSF design concept through: • Identifying key properties of tailings and containment structures; • Reviewing underlying principles for effective operation; • Showing how these apply to select an appropriate TMS; and • Demonstrating how to align the TMS to site-specific constraints and TSF design. This approach follows a path of rigorous data analysis independent of discharge parameters (whether low-density slurry, paste or cake disposal) to select the most cost-effective and sustainable approach for any given material or site.

Jul 1, 2021

By D Sibthorpe

The employment of a tunnel boring machine (TBM) is the default delivery method for the realisation of traffic, utility and primary resource underground space worldwide, with hundreds of kilometres completed safely each year. This is not yet the case for the mining sector in Australia, specifically underground coal mining. The safety advantages of TBM delivery when compared to New Austrian Tunnelling Method (NATM) delivery, or that of drill and blast, remains unrealised.With coal access drifts ranging between 1000?m and 3000?m in length, the construction of these facilities using TBMs could be done in a fraction of the time when compared to current practice. TBM world records currently stand at 435?m/week or 1600?m/month for the 7.0?m to 10.0?m range. Resource owners and developers should embrace the opportunity to deliver access to their orebodies in only a few months, excluding machine assembly and disassembly time.There are challenges in utilising TBMs for construction of Coal access drifts, such as; TBMs generally being bespoke design, maximising capital efficiency for drift development, and geotechnical variances between projects. This paper explores safer and more cost-effective options. This paper also provides detail of how the configuration within a completed drift could be optimised to ensure all site specific needs are met with regard to future use of the drift. The paper also includes descriptions of the engineering solutions that are available for physical and atmospheric challenges specific to coal drift applications and how the TBM manufactures are adapting to the regulatory requirements are also covered.Due to downward pressure on high cost bases and ever increasing safety requirements the popularity of TBMs in the Australian mining sector can be expected to increase and eventually become the default delivery method for coal drift construction, building them cheaper, faster and?safer.CITATION:Sibthorpe, D, 2014. Coal drift construction by tunnel boring machine, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 671–682 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J Jeffery, P G. Knott, F Velge, C Evans

A trigger action response plan (TARP) provides a structured response to escalating levels of risk. In mining, TARPs are typically applied to primary hazards such as inrush, strata failure or heating. Necessary for the creation and deployment of a TARP is a monitoring system capable of detecting deviations from normal conditions. The advent of real-time instruments capable of measuring diesel particulate matter now permit decision-making within shifts to address possible overexposure. Deploying a TARP for diesel exhaust emissions can lower the probability of a person’s average exposure (over a full shift) exceeding the exposure standard by detecting deviations of diesel particulate concentrations from normal conditions. This enables pre-emptive action to mitigate or protect. Another goal is to drive ambient air concentrations lower through the application of corrective actions as a result of instances where concentrations exceed ‘normal’.CITATION:Knott, P G, Evans, C, Velge, F and Jeffery, J, 2015. Trigger action response plans for diesel exhaust exposures, in Proceedings The Australian Mine Ventilation Conference, pp 129–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By M L. Muller, A R. O’Donnell

The Mount Isa Mines (MIM) Copper Concentrator has an extensive history of reagent trials, with different reagents coming in and out of favour over the years. The research and use of carbon depressants is particularly prevalent, as carbonaceous pyrite is a major source of concentrate dilution. Years of research led to the use of naphthalene sulphonate due to its excellent carbon depression properties. However, due to rising reagent costs carbon depression ceased in the late 1990s. This led to the loss of knowledge about the use and value of naphthalene sulphonate. Cyanide is used at the Copper Concentrator for the sole purpose of pyrite depression and over the years multiple projects have been devoted to finding alternatives to it. In 2012 the neighbouring MIM Lead-Zinc Concentrator replaced cyanide with naphthalene sulphonate which resulted in cost savings and the elimination of a hazardous reagent. In 2013, plant trials were conducted at the Copper Concentrator in hopes to replicate the outcomes obtained at the Lead-Zinc Concentrator. The results of the trials conducted at the Copper Concentrator showed that naphthalene sulphonate could not replace cyanide and this work was set aside to pursue more promising projects. Further research conducted in 2014 found that mineralogy and a better understanding of the depressing mechanism of naphthalene sulphonate held the key to improved pyrite depression at the Copper Concentrator. The findings showed that Mount Isa copper ore contains two forms of pyrite; euhedral pyrite (cubic pyrite) and framboidal pyrite (carbon rimmed spheres of pyrite), both of which require different reagents to sufficiently depress them. Naphthalene sulphonate was found to be an excellent carbon depressant, suitable for depressing graphite and framboidal pyrite, whilst cyanide specifically targets euhedral pyrite.In 2015 laboratory test work was conducted to examine the use of naphthalene sulphonate in conjunction with cyanide to selectively target both forms of pyrite. This work led to a full plant trial, the results of which showed a significant increase in plant performance, with higher copper concentrate grades and recoveries being achieved. This paper aims to focus on the benefits and importance of understanding past work and linking a detailed knowledge of feed mineralogy to reagent selection for improved plant outcomes.CITATION:O’Donnell, A R and Muller, M L, 2018. Selectively targeting hydrophobic gangue minerals at the Mount Isa Mines Copper Concentrator, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 413–421 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A Horeth, E Duggan, B Versiani, A Gooch

Iron ore screening plant productivity is strongly affected by the performance of the shuttle operation, with the control system robustness and associated strategies having a direct impact on utilisation and throughput rates. A number of aspects intrinsic to the methods and technologies traditionally applied on the motion control of shuttles are often observed to decrease the efficiency of the ore distribution process across multiple screening modules, which ultimately impacts the plant’s production. Those include the number of operational scenarios that are unmanaged by conventional discrete control logics which may intermittently lead to undesired events, such as ‘high level alarms’ and ‘low level interlocks’ in the screening bins. This outcome usually demands excessive manual intervention by Control Room Operators. A Reinforcement Learning (RL) Artificial Intelligence (AI) solution was deployed to control the motion operation of the scalping and products screening shuttles in an iron ore handling plant. The RL algorithm was trained in advance to handle multiple operational scenarios and generate optimised outputs. In nominal operation, the shuttles are moved in a modulating and highly predictive fashion over the whole range of safely reachable bins. When the need occurs, the AI control agent deviates from that modulation behaviour, limiting its travel range or moving to other groups or clusters of available bins by employing ‘bin jumping’ or ‘ore break’ strategies. The RL platform capabilities include the ability to learn in real time to account for and auto-adapt to new operational patterns and process changes whilst applying improved strategies for shuttle dwelling times, target setting and speed control. The deployed Reinforcement Learning AI solution has better managed the existing challenges associated with the shuttle operation and control, and resulted in a more efficient ore delivery process, superior operations stability and increased production rates.

Nov 8, 2021

By P Christen, D R. Ashley, G R. Power

The Ernest Henry Mine is currently a copper-gold open pit operation situated in north-west Queensland, Australia. It is owned and operated by Xstrata Copper with a current throughput of 11 million tonnes per annum; however, open pit operations are scheduled to cease in late 2011. The deposit dips at approximately 45¦ and extends for at least another 400 vertical metres below the final 530 m deep pit design. Resource drilling from 2002 until mid 2008 has enabled an Indicated Mineral Resource to be established to 1000 m below surface. Scoping and prefeasibility studies (PFS) have been completed toward determining if this resource is suitable for underground mining and a feasibility study is currently progressing with a sublevel caving (SLC) concept. This paper briefly describes the process by which the SLC method was selected, conclusions regarding the non-selected methods, and then discusses the optimisation process used to derive the mining plan. The key optimisation parameters include the production drive spacing, level spacing, draw strategy, cut-off grade and production rate. Key risks will then be assessed and economic sensitivities studied. Final sensitivities will use Monte Carlo simulations to improve the transparency of the projectÆs risk profile. The feasibility study (FS) began in March 2008 and this paper describes the main optimisation steps at the time of writing and outlines the plan for study completion through to March 2009.

Jan 1, 2009

By J Fewings, T McCredden, S Seet, C Fitzmaurice

"Flotation of nickel sulfide ores are generally constrained by nickel grade and impurity concentrations (notably magnesium and arsenic) in the product delivered to smelters. Being a physical separation process, flotation recoveries and grades are limited by the grade recovery curve of a particular operation, where increasing product grades are invariably associated with lower recoveries. Impurities put further pressure on this relationship, as removal of impurities from the final concentrate is almost always associated with nickel losses.Western Areas Ltd are developing a proposed expansion to its Cosmic Boy concentrator to treat an impurity stream, that is high in nickel and would otherwise report to tails. Through the use of BioHeap® technology Western Areas aims to recover the nickel and discard the arsenic to tailings. This expansion will consist of a biohydrometallurgical plant that leaches the nickel arsenic minerals, removing the arsenic as a stable iron/arsenic hydroxide, while recovering the nickel as a high-grade nickel sulfide product (at approximately 50 per cent nickel). This can then be blended with final concentrate to improve nickel grades and recoveries, while simultaneously reducing impurity levels or used to produce high value products like nickel sulfate.The introduction of a small microbial leach plant may be beneficial to base metal concentrators constrained by impurities or grade.Citation:Fewings, J, Seet, S, McCredden, T and Fitzmaurice, C, 2016. BioHeap® - Breaking the Grade/Recovery Curve for Nickel Concentrators, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 361–368 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By G P. S Resende, D E. G Oliveira, E A. S Baeta, T F. Bravin

There is currently in the mining industry, as well as in other industries, a movement seeking to increase investments in decarbonisation processes to help combat global warming. Among some initiatives taken is replacing diesel-powered mobile equipment in the mines with electricity-powered equipment, such as electric off-highway trucks or even belt conveyors in the mining operation. Samarco is a Brazilian mining company that since its conception has used a conveyor belt mining system in its mining operation, using only a small number of trucks to complement the mining process. This mining process that combines conveyor belts and trucks has brought environmental gains for the company since the environmental impact of conventional truck-only mining is greater than that of the combined system. To measure these gains, a medium-term mining plan was developed in which two fleet scenarios were detailed. One scenario contemplated a high level of detail of belt mining seeking its maximisation, while the other considered the operation performed 100 per cent by trucks, eliminating the use of conveyor belts. Through the comparison of these two scenarios, it was possible to make an inventory of atmospheric emissions and greenhouse gases for each one of them considering data such as types of equipment, diesel consumption, total distance travelled and energy consumption. The results showed that the fleet scenario with conveyor belts results in periods with up to 15 per cent less greenhouse gas emissions and 37 per cent less total particulates compared with the truck-only scenario. Therefore, the results confirm the environmental benefits of the method and the need to look for ways to even expand it in future operations through a study to identify the potential areas in the long-term mining plan.

Sep 18, 2023

By M Fitzgerald

Fimiston Open Pit is operated by Kalgoorlie Consolidated Gold Mines (KCGM) as a joint venture between Barrick Gold and Newmont Mining. Over 110 years of underground mining resulted in the development of nearly 3500 km of underground workings including backfilled and open stopes up to half a million tonnes in size. These voids significantly complicate blasting processes at KCGM, influencing blast movement direction and magnitude. Blast movement monitoring to improve mine reconciliations was identified as an improvement project in the business plan for the geology team in 2008. Following successful trials in 2008 to 2009, blast monitoring and translation of ore blocks were implemented as a permanent grade control program from late 2009 and is now part of the Management Operating System (MOS) of the mine. This paper presents a summary of results from the Blast Movement Monitoring (BMM®) data collected to date. Ore blocks at KCGM are translated primarily using BMM® data. This data is obtained from the BMM® system which measures the movement of a radio transmitter installed in a blast pattern from a preblast position to a post-blast position. The application of the data collected by the BMM® tends to be both mine site and blast specific. At KCGM, an average distance obtained from the BMM® data within a given shot is the primary method used for translation. In the case that BMM® data is unavailable, a theoretical movement vector established from Orica Shotplus with distances gained from the historical BMM® database is used. Data is presented in an ore loss and dilution exercise for a bench undertaken at KCGM to understand the potential effects on reconciliations. Improvements that have flowed from implementing blast monitoring include improved reconciliations when combined with other grade control improvement projects. The increase in liaison between the geology and blast personnel at KCGM has been a significant improvement gained from the implementation of the blast monitoring program. This has allowed a better understanding of blast movement and the effects on ore dilution and ore loss by the mine geology team. In addition, the discussion of blasting tie-in plans between geology and blasting personnel has been improved which leads to more favourable blasting practices that take ore movement into account.

Aug 22, 2011