Search Documents

By T M. Nester, D J. Reardon, A N. Page, B J. Barsanti

The load capacity of a friction bolt has long been regarded as 4 t/m of embedment for ground support design analysis and supported by in situ pull test results. In recent years, the authors have observed lower pull test results or inconsistent results which were rarely sighted in the early 2000s. The lower pull test results indicated in some cases that reliable friction bolt capacity (≥90 per cent of results) is closer to 3 t/m of embedment with some geotechnical engineers adjusting the ground support parameters in the design work accordingly. This can be in contrast with other mines which reliably obtain 4 t/m (or greater) using the same suppliers bolt in similar ground conditions. This raised several questions: • What is the effect of poor installation (bolt twist or bolt hole deviation)? • Does the performance of friction bolts vary in different rock masses? • Does bolt performance vary between suppliers? • What effect does increased jumbo feed/percussion/rotation settings have? • Have the bolt dimensions or steel strip width changed? • Have the physical bolt properties changed? • Have the steel properties changed? This paper was aimed to answer as many of these questions as possible and discuss each variable in detail. This project included friction bolt trials at various mine sites across Australia, multiple friction bolt manufacturers, steel manufacturers and laboratory analysis. The paper also includes discussion on what the authors consider best practice for pull testing. It should be noted, the terms ‘friction stabiliser’ and ‘split set’ used in this paper are used in a generic manner and is not linked to any specific ground support supplier. Whilst its acknowledged within the industry the term split set and friction stabiliser is used interchangeably, the authors acknowledge that the term split set is a trademark of Split Set Mining Systems and has been used in context in this paper.

Nov 29, 2022

To gain further understanding of the operating efficiency of the BHP Slab and Plate Products Division (SPPD) RH vacuum degasser, physical and mathematical model studies of the process have been undertaken. The purpose was to investigate how the various process parameters affect the liquid circulation rate, to visualise the flow patterns, and to identify and eliminate the cause of localised wear in the downleg. In the physical model mixing times were measured using an acid tracer technique. The results were applied to predicting trends in times required to obtain homogenous melt composition under varying conditions. A 2-dimensional mathematical model describing the liquid metal flow has been developed using the PHOENICS fluid-flow package. The physical model results were simulated and incorporated into the mathematical treatment and an improved design for vessel geometry is proposed. The effect of rounding the downleg entrance or installing a baffle between the legs is discussed.

Jan 1, 1987

A review of all major TBM projects from 1974 to 1990 has been undertaken and the results entered into a database. A similar database was prepared from information obtained from a principal TBM manufacturer covering the period 1952 to 1990. The database includes information such as machine specifications, machine performance data, tunnel specifications and ground characteristics. The database can be used as a guide to gauge potential machine performance in a range of ground conditions and tunnel geometries. The review also indicates that current TBM technology is limited to certain ground strength conditions.

Jan 1, 1993

Various aspects concerning gold are mentioned below. These have no common theme but suggest points of interest any one of which, if warranted, could lead to development later and elsewhere. 'High level' auriferous gravels The gold deposits of Victoria are commonly classified as being either primary or secondary. Most primary occurrences comprise gold present in quartz reefs, together with other lode-like occurrences in which gold is associated with various sulphides, with or without quartz. Secondary occurrences are derived by physical release of primary gold and subsequent concen- tration of it as a constituent of sediments. Secondary gold deposits may be themselves eroded so leading to third or even fourth generation gold.

Jan 1, 1982

By Barnes R. G, Agostini A, Lewis P. C

The Mineral Resources Audit is a five-year Program established to produce a comprehensive and objective assessment of the mineral resources of New South Wales, including prospective resources. The goals of the Program are to improve planning and land use decision-making; attract exploration and minerals related investment; help the Department to identify and fill gaps in knowledge; and develop methods to identify and quantify resource potential and prospectivity. To achieve the goals of the Audit it is necessary to assemble and enhance a large amount of information and it is necessary to spatially analyse this information using computer-based Geographic Information Systems (GIS) which allow the collection, storage, transformation and display of large quantities of spatial data. An extensive range of both map-based and textual data can be employed in spatial analysis and resources and geoscience modelling. In order to use this information, data sets have to be corrected and standardised. Many data sets need to be classified. An objective of the Audit Program is the spatial analysis of the State, region-by-region, and the release of cleaned-up multiple digital data sets as packages which include upgraded mineral deposit information, 'seamless' geological map layers showing lithology, structures and stratigraphy, and processed and classified geophysical map layers. These regional packages are important reference sets for the mineral resources industry and will assist delineation of regional exploration targets.

Jan 1, 1995

By S Hughes

The smelting of concentrates and secondary materials has been subject to increasing challenges in recent years due to declining grades of feed materials, increasing impurity levels and ever more stringent environmental regulations. In addition there has been a growing focus on maximising the efficiency of energy usage and recovery of values. New opportunities have been created with rising metals prices and improved systems for the collection of secondary materials, giving rise to a need for more flexible process solutions.This paper focuses on a number of specific cases where a process solution has been developed using the Outotec« Ausmelt Process to meet particular feed material challenges and overcome limitations inherent when employing traditional pyrometallurgical processes.The first case involves the development and commercial implementation of a smelting process to recover values from zinc smelting residues typically deposited into dams as a waste product. The second case describes the application of the Ausmelt process for the smelting and converting of secondary copper feed materials, including e-waste. These materials contain a wide range of metals and plastics and need to be processed appropriately to maximise the recovery of values whilst avoiding environmental problems. The third case study covers the smelting of nickel concentrates containing elevated magnesia levels as well as nickel bearing catalysts with high alumina content, neither of which can be readily processed when employing traditional pyrometallurgical technologies. CITATION:Hughes, S, 2013. Pyrometallurgical process solutions for complex raw materials, in Proceedings MetPlant 2013 , pp 519-530 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Dharmappa HB, Sivakumar M

This paper is concerned with two case histories of wastewater quality management in underground coal mines in the Illawarra region. The first investigation briefly presents an analysis of mine water discharge having an extremely high concentration of suspended solids and consistently high barium concentrations, averaging, 14.4 mg/I Barium, over the sampling period. A laboratory study of chemical precipitation processes has indicated that about 91% of barium could be removed by using ferric sulphate and lime. On the basis of the information obtained from the environmental audit process an alternative water treatment and reuse system incorporating 51% reduction in the water consumption with 32% less off-site discharge has been suggested (Thomas, 1995).The second case history is concerned with the storm water management at a mine situated in the Illawarra escarpment where only 20% of the wastewater generated in the colliery is discharged off-site. Computer modelling of the storm water system showed that 75% of the clean runoff becomes contaminated through poor management practices and causes the process wastewater treatment system to fail in wet weather. Suggested improvements include relatively simple alteration to the coal wash filtration dams which are expected to reduce the periods of inefficient operation of these dams by 95%. The use of storm water diversion channels and detention basins can reduce the overflow volumes by 70 - 100 % for a ten year ARI (Average Recurrence Interval) storm event (Wingrove 1996).

Jan 1, 1998

By Baafi EY

Open cut mining in Australia is facing the greatest challenge in its history in attempting to compete not only with other operations internationally, but also with underground operations domestically. Most flat dip and shallow depth surface-mineable coal reserves have been depleted during the last two decades and new open cut operations must extract deeper coal deposits. As open cut coal mines move into deeper areas and the stripping ratios increase, the relative cost of overburden removal also increases. It therefore becomes even more important to design the mine around the optimum overburden removal scheme. The deeper mines are usually multi-seam operations with a more complex geology and with more geotechnical and hydrological problems. Deeper mines are subjected to greater problems requiring more detailed mine planning and design, such as selection of the optimum mining method and pit layout. In planning and design of such operations, the number of alternative methods which need to be considered is consequently greater.Dragline productivity and its stripping capabilities are directly affected by the selection of digging method, strip layout and pit geometry. Every mine has a unique combination of geological conditions. The operating methods that work well at one mine may not necessarily work at another site. Selection of an optimal stripping method, strip layout and pit geometry for a given dragline must be considered with respect to the geological conditions of the mine. With increasing geological complexity of Australian strip mines, it is becoming more important to use sophisticated techniques such as computerised mine planning methods to assist in optimising dragline operations.

Jan 1, 1998

By Millett R

In January 1989, Western Mining Corporation (WMC) acquired the Perseverance and Rocky's Reward orebodies and associated infrastructure from the Agnew Mining Company (AMC). AMC had closed the operation in August 1986 and it had been on care and maintenance since that time. To return the operation to full production as quickly as possible it was planned to mine the Rocky's Reward orebody by opencut mining and treat this ore whilst the underground Perseverance workings were rehabilitated. Removal of overburden from Rocky's Reward thus commenced immediately with a target of April 1989 for delivery of the first ore to the concentrator. Extensive rehabilitation and upgrading of the concentrator commenced in late January, and continued in stages for an 18 month period. The first stage consisted of overhauling all existing equipment and completing a crusher upgrade commenced by AMC prior to the mine closure. During this period, it was necessary to recruit a workforce and re-establish all the required support structure. In late April the plant commenced commissioning trials on mullock. The first ore was crushed on the 11th May 1989 and concentrate produced the following day. From May 1989 to June 1990 the plant was producing nickel concentrate whilst further upgrading continued. During this period, the flotation capacity was tripled by installation of a bank of eight Wemco 144L flotation cells in rougher-scavenger duties and two 12 metre by 2 metre diameter columns in cleaning duties. The existing vacuum drum filters were replaced by two Larox PF32 pressure filters, eliminating the need for solar drying and allowing the flash drier to be fed direct from the filters. These, along with a major borefield expansion and further work to the crusher increased the nominal plant capacity from 600,000 to 1,000,000 t/yr. The plant achieved the 1,000,000 t/yr rate in April 1990.

Jan 1, 1991

By Moxon N. T, Berndt J. R

BHP-Utah Coal Limited's Peak Downs Mine is located in Cen- tral Queensland, approximately 200 km south west of Mackay. The annual raw coal production of the mine is over 8 million tpa, requiring the removal of about 40 million cubic metres of prime overburden. This is achieved through the use of five large draglines. The large depths of overburden (up to 55 metres) encountered over half the strike length of the mine enables cast blasting to be carried out in conjunction with draglines employ- ing the chopping method of digging. The objective of cast blast- ing is to use explosive energy to move as much material directly into spoil as possible. The additional costs of drilling and blast- ing are offset by reducing dragline rehandle. Two factors which are of primary importance to the design of cast blasts are initiation control and material velocity. High speed motion picture photography is a powerful diagnostic tool to quantify these aspects of blasting (Winzer, Montenyohl and Ritter, 1979; Chiappetta et al., 1983; Anon., 1983). The objec- tives of such analysis are to: 1. Determine the burden velocity, 2. Determine the time to initial movement (that is, the inter- val between a face hole firing and the initial movement of the burden), 3. Check the accuracy of the initiation sequence. BHP Central Research Laboratories (CRL) and Peak Downs Mine monitored a cast blast in the mine's Winchester Pit on 18 August, 1988. The objectives of this exercise were to: 1. Quantify current cast blast performance, providing a base case for comparison with modified blast design. 2. Compare two orientations of angled holes within the blast. 3. Assess the effectiveness of cast blasting utilising an air-deck. 4. Check blast timing with respect to burden movement times.

Jan 1, 1989

By Ward S. C, Gardner J. H

In 1990, Alcoa of Australia Limited was elected to the Global 500 Roll of Honour of the United Nations Environment Program for the environmental management and rehabilitation of the bauxite mines in Western Australia. This award placed Alcoa in the international best practice category. The story of constant improvement spans more than 20 years from a 'trial and error' start to a strategically focussed and research driven program today. The main driving force has come from within the company, against a set of strong corporate values and a well publicised Vision based on 'excellence through quality'. Along the way public opinion, action group protests, increased legislative controls together with the professional competence of internal and external environmental resources have all played a part in arriving at the level of current environmental management and mine rehabilitation performance. There were numerous lessons learned here during the evolution and maintenance of best practice. These included: I . To work diligently in obtaining a vision or strategic intent on mine site rehabilitation and environmental management - don't be easily dissuaded.

Jan 1, 1995

By A F. Cooper

The northeast-southwest trending ~25 km2 area incorporating Bald Hill is located 18 km northeast of Haast, and 5 - 7 km west of the Alpine Fault in South Westland, New Zealand. The geology consists of Greenland Group greywacke overlain by a Cretaceous-Tertiary sedimentary sequence and fluvio-glacial/marine terrace deposits of Quaternary age. Alluvial gold in Cole Creek, draining west from the summit of Bald Hill, may be derived either from vein mineralisation in basement rocks or from fluvial or marine terraces.   This paper focuses on the potential for in situ gold and base-metal mineralisation in sporadic, siderite-rich quartz veins that cut basement greenschist facies metasediments that have been overprinted by contact metamorphism.   Throughout the area, vein compositions are dominated by quartz and commonly feature zoned plagioclase. Alteration adjacent to veining within the contact aureole is dominated by 1 - 2 mm, coarse grained biotite, with small amounts of sulphide, and is pervaded by abundant siderite veinlets. Outside the aureole, wall rock alteration to veins consists of fine grained chlorite. Trace element XRF analysis has been used to ascertain base metal concentrations within samples of vein and alteration zones collected from throughout the area. Vein and alteration zone mineral assemblages containing <5 per cent sulphide, with low concentrations of As, Cu, Pb and Zn indicate low potential for gold and base-metal mineralisation in the Bald Hill region. Contact metamorphism of Greenland Group basement in the northeast of the region, is likely due to emplacement of a poorly exposed Cr- and Ni- enriched gabbro. The presence of biotite and andalusite in hornfelses indicate contact metamorphism occurred at temperatures >350¦C and at depths <10 km. Widespread vein distribution does not appear to be related to contact metamorphism or gabbro emplacement. Further research is required in order to establish the fluid source from which the veins were precipitated.

Jan 1, 2007

By Cocker A

Pre-splitting for smooth highwall formation is conducted in around 75 per cent of surface coal operations within Australia. The CMTE (Centre for Mining Technology and Equipment) in conjunction with BHPAC (BHP Australia Coal) initiated a project to look at pre-splitting and to investigate the notching of blastholes for fracture plane control. The notching was specifically for pre-split initiation and also for discing of the toe of the production holes to minimise coal loss from the top of the coal seam. There are currently a number of factors which are driving the introduction of new pre-splitting technologies and products. The first is the ever increasing bench height being employed in strip mines which require a higher quality wall with less blast damage to maintain stability. Currently depths of 55 metres are common place with depths of 70 - 80 metres fast approaching. The second factor is the introduction of new technologies or methods which require a high quality highwall produced, eg highwall mining. This paper discusses the current state-of-the-art in pre-splitting and the main issues facing successful pre-splitting in the future. The use of a blasthole notching technology to promote fracturing along the pre-split line is also analysed. The review indicates that most pre-splitting challenges in the future can be addressed through better use and developments of current drill and blast technology. It is also concluded that a blasthole notching technique may find niche applications in improving final walls within a surface coal mine, especially where a high quality wall is required. The notched blasthole method may also allow pre-splitting in ground conditions and adverse rock structure which currently cannot be pre-split by existing technology.

Jan 1, 1995

By Takagi T, Seetharam R, Sie SH, Naito K

Tin-polymetallic vein type deposits are one of the major source of metal producers in the Circum Pacific Belt. This type of deposit is of great importance for the modem electronics and medical industries because of their high content of rare metals (especially indium and bismuth). We have studied two representatives, Tosham of India (Cu-In-Bi-Sn-W-Ag-Au), and Mount Pleasant of Canada (Zn-Cu-In-Bi-Sn-W), using proton and electron microprobes in order to delineate the distribution of medical/high-tech rare metals. The electron microprobe study showed that major indium carrier in such type of deposit are roquesite (CulnSZ), sphalerite, stannite and a Cu-Zn-Fe-In-Sn-S mineral; and that indium is incorporated in sulfides by coupled substitution like Cu + In = 2(Zn + Fe). The proton microprobe showed that indium at trace levels is also present in chalcopyrite and pyrite. In addition, zinc, copper, arsenic, antimony, selenium, tin, and bismuth are common in chalcopyrite and pyrite. Arsenopyrite contains nickel, copper, zinc, silver, tin, antimony and bismuth. In chalcopyrite and pyrite, zinc, arsenic, indium, bismuth and lead are higher in Mount Pleasant ore, but silver is higher at Tosham. Also thallium and gold were found only in Tosham pyrite. The Tosham deposit is genetically related to S-type magma, while the Mount Pleasant deposit is related to A-type granite. Tosham ore contains zinc-bearing biotites that coexist with chalcopyrite in ore bodies but Mount Pleasant ore lacks such biotite. We propose that the difference in elemental abundance between the two deposits are caused by the different character of source magma and different mineral associations of the ore body.

Jan 1, 1995

The effects of process variables such as solution chemistry, flocculent type and dosage, intensity and duration of mixing, and solids type and concentration, on the performance of flocculation/clarification/thickening processes are described. System response is evaluated in terms of the specific effects on floc settling, supernatant clarity and sediment compressibility. The implications of these results with respect to industrial practice are discussed and general guidelines for direct application to plant design and operation are suggested.

Jan 1, 1993

By Dagbert M, Belisle J. M

Several packages for the estimation of porphyry type deposits exist and produce acceptable results. Recently, however, the need for really trying to obtain maximum information from drill holes has prompted the generation of geostatistical solutions to the problem of reserve calculation. It will be shown that an understanding of a few key points is necessary in order for these solutions (variogram analysis and kriging) to he really ptimal. The most important new fact to be ecognized in open pit ore reserve estimation is that block models do not give an accurate rediction of ore tonnage when a cut-off is pplied but often yield an overestimation of p to 25%. When checked against extensive roduction records, geostatistical methods provide a practical solution to this problem. t now seems that the model used here gives he best possible results. Inasmuch as all arge deposits present very similar geostatis- ical characteristics only a few days of work re necessary to produce a complete inventory f these. The techniques used will be demon- trated using examples from five deposits and pecial emphasis will be given to the accurate rediction of tonnages of ore and waste using he new "transfer function" technique of G.

Jan 1, 1977

By Anderson RJ

Tower Mills are used at Aberfoyle's newly commissioned Hellyer base metal sulphide concentrator. Hellyer ore is particularly fine grained. To achieve adequate liberation fine grinding is necessary. Three Tower Mills are used on regrind duties, grinding to less than 20 microns. The physical arrangement, material flows and grinding characteristics for the Hellyer Tower Mills are described. The mills have performed satisfactorily, both in size reduction and power efficiency. Wear parts must be inspected and changed more often than with ball Mills. To date, 92 per cent availability has been achieved. As parts and maintenance routines are rationalised, this is expected to improve to 96 per cent. Modifications to wear parts for the Hellyer Tower Mills are discussed.lhc Tower Mill grinding environment is highly reducing. The impact of Tower Mill regrind on downstream flotation is discussed.

Jan 1, 1991

By M Sparrow

The Victoria Park Tunnel project is an inner-city alliance project in central Auckland, New Zealand. The existing two-directional viaduct will be modified to single-direction flow, and a new northbound 440 m cut and cover tunnel will be constructed beneath Victoria Park. Three-dimensional (3D) visualisation media were used to communicate key design innovations to stakeholders and the general public. The 3D visual material has proven a useful tool for informing motorists of a new safety barrier method adopted for traffic management.This presentation will explain how 3D visualisation was incorporated in the project and will showcase the 3D visualisation media created for the project.

Mar 8, 2011

The Drake-Rivertree area lies in the far north east of the New England district of New South Wales. Drake is some 500 miles north of Sydney by road and 36 miles west of Lismore. Rivertree is situated 24 miles north of Drake.The Drake deposits were first worked in 1878 for gold which occurred in a very fine state in ferruginous gossan but at depth copper ore became more significant. The lodes at Rivertree, discovered in 1887, were worked for silver but mixed sulphides became more prominent in deeper levels.Several mines operated at each centre and each locality smelted its own ore.The mines at both centres were operated sporadically for many years though production was not particularly substantial.A number of the larger mining companies have shown a recent interest in this mining field with special emphasis on the Drake locality.GENERAL GEOLOGYThe two mining centres are situated to the north and south respectively of a belt of Permian marine sediments and volcanics similar to, and probably representing an easterly extension of, the rocks of the Emmaville district further west.E. C. Andrews (1907) recognized two stratigraphic units within what he called the Drake Series. The Lower Division consists of rhyolite flows, tuft's, breccias and agglomerates, followed by trachytic and andesitic tuft's containing cladochonns, thanmopora willcinsoni and other Permian forms.

Jan 1, 1962

High interest to basic-ultrabasic rocks is ex-plained by their specific, sutural, geotectonic po-sition and by deep level of generation of ultraba-sic magmas. These two factors allow us to treat this group of rocks as valuable source of informa-tion about the lower crust and upper mantle of the Earth. Basic-ultrabasic xenolith series is another source of information about the interior of the Earth. Detailed studies of the xenolith series give valuable material to geologists as to how endogenic deposits are fed and what is their source.Besides, the interest is explained by attempts to understand the relationship between basic-ultra-basic complexes and deposits of metalliferous and non-metalliferous mineral material.Absence of genetic boundaries in manifestation of metalliferous and non-metalliferous minerals, their temporal and spatial relationship allow us to treat the minerogenesis of ultrabasic complexes as a result of one ore-forming process manifested in Koryak-Kamchatsky, Sakhalin-Japanese, Ryukyu-Korean and Taiwan-Philippines island arc systems which re-present, in the opinion of the authors, one eastern Asian chain of the Pacific ore belt (Radkevich, 11)87).

Jan 1, 1990