Search Documents

By C Grobler, M Recklies, G Jiang, I Taylor, M Morgan, G MacDonald, L Smith

The resource estimation of lateritic deposits, such as Aurukun, presents specific issues related to the lateral changes in thickness and elevation of the various horizontal layers (or zones) within the deposit where the x and y dimensions are orders of magnitude greater than the z dimension. The objective was to develop a three-dimensional (3D) block model that retained the vertical and lateral variation inherent in deposits of this type to allow full optimisation of the production plan without prior selection of an economic portion (enriched bauxite layers) of the profile at the resource estimation stage. The Aurukun bauxite deposit is held by Chalco Australia Pty Ltd (Chalco) and forms part of the world-class Weipa bauxite province, Cape York Peninsula, Queensland, Australia. The bauxite is predominantly pisolitic with an upper boehmite-rich zone and lower gibbsite-rich zone. The bauxite consists of both in situ and reworked domains, is overlain by a thin soil horizon and has kaolinite clay as a transitional base. A portable infrared mineral analyser (PIMA) was utilised on site, in addition to elemental assay, on each drill sample to determine the mineralogy, in particular levels of boehmite, gibbsite, kaolinite and reactive silica. As part of the scope of work, a field program was undertaken using large diameter Boart Longyear sonic drilling to acquire detailed density measurements across the deposit to allow compliance with Joint Ore Reserves Committee (JORC) reporting requirements. Interpretation of the stratigraphy was conducted on a hole by hole basis with definition of the zone layering based on stratigraphy, geochemistry and mineralogy. The zone boundaries were then modelled as 3D surfaces and used to constrain a block model. The block model estimation used the ordinary kriging method, with the estimation done in unfolded space and then refolded, therefore maintaining the zones irrespective of thickness or orientation. The unfolding process converts the real-world positions for both blocks and informing samples to a scaled position relative to the roof and floor of each zone. Analysis of the data and variography were also undertaken in unfolded space. The x and y dimensions are unchanged, but the z dimension is a relative position. The effect of the unfolding and limits on number of samples per hole is to æpushÆ the informing sample search sideways but within the stratification, rather than vertically. This honours the strong vertical zonation within the bauxite profile. The JORC Code requires that the stated resource must have æreasonable prospects for economic extractionÆ. This is a qualitative rather than quantitative definition. A number of selection criteria to define a resource roof and floor were developed in consultation with the project engineers and owners to meet these criteria. The vertical selection of material to include in the resource highlights the variation in the development (and destruction) of the bauxite profile from area to area within the deposit.

Jan 1, 2009

By F K. R Klose

Malmberget is a sublevel caving mine owned and operated by Luossavaara-Kiirunavaara Aktiebolag (LKAB), a Swedish state-owned iron ore mining company, in northern Sweden. The mine has an annual iron ore production of approximately 15 Mtpa. The current strategy foresees an expansion which will increase the mine’s depth considerably. Ventilation and air conditioning modelling for the planned expansion is ongoing. One of the most influential parameters for ventilation planning anddesign for a deep mine is geothermal gradient, which is crucial for the design of the refrigeration system. It is determined through virgin rock temperature (VRT) measurements carried out at various depth below the surface. This paper details these measurements and the determination of geothermal gradient for Malmberget Mine for the expansion study, which were necessitated by thelack of information for the focus depth and area.

Oct 12, 2022

By B E. Hall, J Poniewierski, A J. Hills

Following a review of life-of-asset work at MMG’s Rosebery mine in which a proposal to increase production from 0.8 Mt/a to 1.2 Mt/a was mooted, questions were raised as to the seemingly arbitrary reasoning for the production increase. They included: Did the proposal actually add value? Was the production rate from the mine sustainable? Was it the best identifiable value-adding configuration?A multiple scenario analysis study commenced to model how various cut-off grade values against mill throughput, along with associated capital expenditure, would impact on the potential value of the operation. This was carried out utilising the ‘hill of value’ approach promoted by AMC Consultants.The traditional approach to these studies uses a constant cut-off value (NSR – net smelter return) for the whole mine analysis. This was thought to potentially introduce a large amount of variability to the model as different ore types were thought to have different processing costs and different underground lenses were thought to have different mining costs. With the aim of developing a consistent value measure that would be comparable between the lenses, an alternative measure was suggested for all ore block values in this model, irrespective of lens location.The new measure used was a mine variable value (MVV). This allowed for the variable factors of final metal concentrate production to be removed from the ore value. From a mining point this was the haulage distance from ore source to run-of-mine (ROM). For the mill it was the amount of reagents required, varying based on grade together with the amount of power required for crushing, grinding and tailings handling.From the initial run of the model, preliminary results lead to a conclusion of increased value being gained by either increasing cut-off grade or increased mill throughput rate. The validity of the result was tested using alternative price scenarios, which although changed the absolute value achieved did not significantly change the identified value-adding strategies. The realisation of these value increases identified are however contingent on higher sustainable development rates being able to be achieved mine-wide, higher backfilling rates being able to be achieved and overcoming recognised ventilation constraints. Further detailed studies are being put in place to identify the practicality of overcoming these recognised constraints and achieving the higher-value strategies identified.The ongoing objective of the hill of value model built is to keep the model alive as a life-of-asset planning tool and to continue refining the foundation data, such that various mining strategies can be analysed with increased confidence.CITATION:Hills, A J, Hall, B E and Poniewierski, J, 2014. Mining scenario analysis and mine variable value, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 111–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By J Addai-Mensah, W Skinner, C Kelsey, J R. Kelly, E Baawuah

Comminution continues to be the most capital-intensive unit operation in mineral processing. The fundamental purpose of comminution is to liberate the valuable minerals so that they can be economically concentrated into saleable products. Declining ore quality characterised by lower grade and increased complexity requires significant energy consumption for comminution. Low-grade magnetite ores are typically fine-grained and require fine to ultra-fine grinding (P80 ~ 30 - 40 µm) to enhance its liberation from the typically siliceous gangue matrix. Historically, this has been achieved using multi-stage crushing and grinding technologies, which require high energy consumption with low energy efficiency. This motivated innovations in energy efficient technologies for comminution. Such technology has been developed in the IMPTEC super-fine crusher. It is an innovative, dry (with the potential to be operated wet), media-free, energy efficient crusher that can to reduce 10 mm feed particles to 19 – 30 µm with very low recycle loads. In this study, the mineralogical and physicochemical characteristics of crushed magnetite ore using the IMPTEC super-fine crusher have been investigated in comparison with those of rod milling. The super-fine crusher generated higher liberated magnetite minerals in the – 300 + 212 µm and < 45 µm size fractions compared to rod mill. Both comminution devices generated large low-grade hematite and goethite middlings. However, the rod mill produced higher locked/unliberated hematite and goethite compared to that of the super-fine crusher. Quartz mineral had the highest liberation irrespective of the comminution device used. The super-fine crusher generated higher entrapment of other minerals within the silica matrix compared to the rod mill. The breakage mechanism of the super-fine crusher which is predominantly through high compression with shear, generated improved mineral liberation in the coarse size fractions compared to the predominant abrasion and attrition breakage mechanisms of rod milling. The higher mineral liberation generated by the rod mill is potentially due to the prolonged batch milling of the ore compared to the single-pass open circuit of the super-fine crusher.CITATION:Baawuah, E, Kelsey, C, Kelly, J R, Addai-Mensah, J and Skinner, W, 2018. Mineral liberation studies of IMPTEC super-fine crusher – 130 crushed product, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 313–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By H Yuan, H Tian, Y Zhang, Z Wang, C Wang

Submerged arc welding (SAW) is one of the significant metal-joining processes for manufacturing marine vessels, steel pipes, and offshore structures with high deposition rate and engineering reliability. Welding flux serves several essential functions, including atmospheric shielding, arc stabilisation, bead morphology control and weld metal (WM) refinement. Therefore, from a thermodynamic point of view, the focus for flux design and WM compositional/microstructural modification has been placed to elucidating the transfer pathways and mechanisms of major alloying elements, such as Si, Mn, Ti and O during welding. To this end, a thermodynamic model has been established to predict alloying element contents in the WM. Such functions are enabled by the physicochemical properties of the fluxes, which are inherently rooted in the nature of the fluxes. A unique yet systematical investigation, including physicochemical property changes and structural evolution behaviours, has been conducted over the wide range of fluxes applied to actual welding of EH36 shipbuilding steels. Combined with spectroscopic methods, structural behaviours of network formers such as SiO2, Al2O3 and TiO2 and network modifiers such as MgO, MnO and CaO have been illustrated. Viscosity and ionic conductivity have been found to be positively associated with the degree of polymerisation.

Aug 21, 2024

By Green A. D M

The establishment of the Imperial Smelting Furnace at Sulphide Coporation Pty. Limited for the smelting of zinc and lead made it necessary to design and install sintering capacity to produce approximately 500 t.p.d. of zinc-lead sinter. The updraught sintering process installed is a recent development and the plant was designed with adequate flexibility and equipment to enable operating staff to investigate the process and achieve maximum production under optimum operating conditions.Sulphur dioxide gases from the sinter machine are passed to a contact acid plant for the manufacture of sulphuric acid.

Jan 1, 1964

By S Maritsa, E K. Chiwandika, S M. Masuka

The iron and steel industry is experiencing an increase in the use of iron and steel commodities within societies, decarbonisation pressures, depletion of high iron ore grades and high energy consumption. This necessitates scrap metal recycling, low-grade ore utilisation using the induction or electric arc furnace to achieve the global target of net zero CO2 emission. The available highquality scrap metal cannot sustain the steel industry but the world has unused hematite-goethite ores. It is the aim of this research that this resource be utilised using the induction furnace to sustain the steel industry in an environmentally friendly manner. Indurated pellets prepared from the hematite-goethite ore, 5 wt per cent limestone and 5 wt per cent coal addition were smelted in the induction furnace at 1350 ± 50°C with 25 mins holding time. The effects of basicity and carbon content were also investigated to optimise the smelting parameters. The results showed that the careful control of the basicity, and iron-to-carbon ratio maximised total metal recovery. The optimal basicity ratio was determined to be 1.3 and a carbon to iron ratio of 1.4 achieved a total metal recovery of 73 per cent. The metal recovery was closely related to the estimated slag melting temperature. The basicity ratio of 1.3 achieved the lowest slag melting temperature estimated to be around 1380°C based on the CaO-SiO2-Al2O3 phase diagram. The recovered metal had a comparable chemical composition and microstructure to that products from an ITmk3 furnace.

Jun 19, 2024

By Dunlop A. C

A brief study from the Mt. Bulga prospect com- pares the chemistry and mineralogy of different soil fractions and other materials to suggest a sequence of surficial metal dispersion from adjacent gossans, which may have relevance for geochemical exploration in semi-arid terrains. v v v v v JIV-- v v v v a o v o/ v v v v 1 v v lv ./v '' 1 v 16400N ..I v 1635014 v 1630014 .:1 ò.t SILURIAN sillstone " lelsic volcanic sillstone -sandstone ORDOVICIAN Eandesite o quartz float gossanò pits doOP Iv o shalt v _--'fault v 1---1 soil traverse v v v v 0 100 200 mm e Fig. I Local geology and location of soil traverses, Mt. Bulga (compiled from Chisholm, 1976). The Mt. Bulga prospect in central New South Wales is a small but well documented volcano- genic massive sulphide occurrence (450,000t of 0.8% Cu, 1.3% Pb, 5% Zn and 0.45 g/t Au) Cambrell and Kirk (1974), and Chisholm, (1976). Mineralization is localised near the interface of felsic pyroclastics with overlying silt- stones and along adjacent faults (Fig. 1). In this area with a Koeppen type cf6 climate, soils are thin and skeletal along ridges with thicker and better differentiated profiles with a colluvial component up to 2m thick developed

Jan 1, 1988

Rather like the mythical "Economic Man" "an employer" in this context must necessarily be an abstraction, and the views possessed by such an abstraction, a composite of many views known to have been expressed. Not even the complex Conciliation and Arbitration legislation in this country provides any helpful specifications, except in one peculiar particular. The Australian Conciliation and Arbitration Act provides an almost totally tautological definition, except in that one oddity referred to above. It is this : "An employer means any employer in any industry, and includes any person who is usually an employer in an industry, and also includes a Club." No doubt there is some perfectly justifiable reason for such specific and unique particularity in an otherwise meaning- less definition. That need not trouble us in this exercise.

Jan 1, 1982

By W N. Qin, B Zhang, W Z. Huang, X S Mo

Mengzi Mining and Metallurgy Co, Ltd (MMMC) polymetallic ore contains recoverable amounts of tin, lead, zinc, pyrite and other valuable minerals. With the change in orebody, the run-of-mine (ROM) ore changed from lead zinc rich ore to tin rich ore, where the current ROM ore contains 0.45–1.25 per cent tin, 20–25 per cent sulfur, and 0.20–0.35 per cent copper. The previous processing flow sheet was designed to recover lead zinc rich ore and it is clearly not suitable for recovery of the current tin rich ore, where the tin was already overground and tin recovery was only 50.19 per cent. The Mengzi Mining Company has recently modified the concentrator circuit by incorporating rod mill and high efficient Derrick fine screen. As a result of the improved classification efficiency, the overgrinding of the tin ore was minimised and the recovery of tin was improved by 20.71 per cent, ie from 50.19–70.90 per cent. An additional $10 M revenue per annum can be achieved as a result of the modification.CITATION:Qin, W N, Huang, W Z, Mo, X S, Zhang, B and Wheeler, J, 2014. Application of high efficient fine screen to improve the recovery of tin concentrate, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 487–492 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D Wimpenny

The Bogong Power Development Project in Victoria, Australia involved the construction of a 15 m long mass concrete plug up to 9 m in diameter within the head race tunnel. The plug is critical to theperformance of the scheme as it permanently seals the head race tunnel under approximately 300 m head of water.The location of the plug in the headrace tunnel was determined by a programme of in situ rock stress testing using both hydrofracturing and over coring stress testing methods.In recognition of the importance of the plug, the Head Contract specification requires that its temperature during hydration be controlled using an embedded cooling system. In addition, contact grouting and curtain grouting around the plug cannot commence until thermal contraction was substantially complete.This paper describes the use of bespoke fi nite element software to model the temperature rise in the plug and design mitigation measures to control temperature rise in the plug. These measures include restricting the concrete placing temperature to 10°C, incorporating 39 per cent fly ash in the concrete and installing embedded cooling circuits.Site trials were undertaken to calibrate the model for the proposed concrete mix. The cooling system comprised 25 mm ID pipes forming twelve separate circuits that fed 7°C water from a single chiller unit. The cooling system reduced the peak temperature in the plug to approximately 30°C and the associated risk of early-cracking. The time before contact grouting could commence was shortened to less than two weeks from casting.

Mar 8, 2011

By G Stovpchenko, G Jianjun, L Medovar

Electroslag remelting (ESR) today and into the future, will still be the main process for producing high-quality ingots by suppressing segregation, not just refining chemical composition from impurities. This paper analyses state-of-the-art electroslag refining with a focus on ESR with consumable electrodes, and recent technology with liquid metal supply (ESR LM) in view of their refining abilities and development trends, taking into consideration that the size of the ingots required by industry continues to grow, and the composition of new materials sophisticates to withstand increasingly higher mechanical and temperature loads . The yield of suitable metal in large ingots produced by conventional casting is low due to problems of element segregation by height and crosssection. For example, conventional ingots for nuclear powerplant rotors today reach nearly 700 t in weight. Attempts to directly replace such giant ingots with big-diameter ESR ingots weighing approximately 400 t were also unsuccessful because of growing segregation. Modern ESR equipment and technologies produce 200–250 t of ingots of satisfactory quality, reaching 2.5 m in diameter, implementing the change of consumable electrodes during remelting to increase ingot length. Another way to mitigate segregation is to enlarge the smaller diameter ESR ingot by a 500– 800 mm coaxial layer to the desirable diameter by ESR in the current-supplying mould (CSM). Modelling and experiments prove that refining from impurities and non-metallic inclusions at ESR most effectively occurs at the slag bath and liquid metal pool interface because the ESR LM has provided the same desulfurisation. ESR’s special refining capabilities in CSM come from the much longer time of LM residence shown at titanium purification from hard-melting nitride inclusions that are unremovable in vacuum arc remelting (VAR) and electron beam melting (EBM). Implementation of ESR technologies in CSM, especially with LM supply, is prospective to produce heavy enlarged and hollow forging ingots with prevented development of segregation due to dividing cross-section and reducing overheat of solidifying metal.

Jun 19, 2024

By A Parbhakar-Fox, B G. Lottermoser, N Fox

"Determining the deportment of economic and environmentally significant elements in sulfidic mine materials (eg ore, gangue and waste) requires the use of advanced microanalytical techniques, including electron microprobe analysis (EMPA) and laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS). Sulfidic boulders were sampled from an acid rock drainage impacted ephemeral stream adjacent to historical copper-silver workings at Baal Gammon, northern Queensland. The abundance and deportment of a range of trace elements and precious metals were analysed in these samples. Whilst many of these elements represent a potential environmental risk if leached from sulfidic rocks into streams in the surficial environment, significantly some of these elements (eg In, Sb and Co) represent specialised metals that are currently considered to be in critical supply.Sulfidic waste rock material at Baal Gammon is dominated by chalcopyrite, arsenopyrite, pyrrhotite and pyrite. Microanalytical investigations revealed that chalcopyrite contains significant quantities of In, Sn, Ag and Zn either substituted directly into the crystal lattice or occurring as discrete sphalerite and stannite inclusions. Arsenopyrite, which may comprise more than 50 per cent of some boulders, is notably enriched in Sb, Co and Ni but also contains inclusions of sphalerite, chalcopyrite and stannite. In contrast, pyrrhotite contains no trace elements of economic significance, but instead represents a likely contributor to acid generation during oxidation in the surficial environment. Trace metals (eg In, Sb, Co, Ni, Zn) are liberated during sulfide oxidation of these boulders in the surficial environment, generating a metal-rich, low-pH leachate.Fe-oxides precipitated as rinds on the surface of these boulders under low pH conditions also contain abundant As, Bi, Sn, Cu and Zn. Abandoned or historical mines represent potential sources of metalliferous drainage that poses potential environmental risks to water and habitats. However, sulfide-rich historical waste rock, stockpiles and processed waste (eg tailings) at abandoned mines may also represent significant sources of critical (eg indium) or other significant metals (eg Sn) that if liberated economically could improve environmental conditions in and around abandoned and historical mines.CITATION:Fox, N, Parbhakar-Fox, A and Lottermoser, B G, 2016. Critical and Deleterious Metal Deportment in Sulfidic Waste Rocks, Baal Gammon, North Queensland, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By S Gillies, H W. Wu

A study has been undertaken into mine ventilation systems currently in use within Australian modern coal longwall (LW) extraction mines. It reviews systems and discusses evolving changes being adopted to address the more complex challenges. There is a strong move to longer panels, wider faces, greater extraction heights, increased production rates, more efficient ventilation and decreased personnel. Each of these changes is motivated by improvement in productivity and generally leads to cost reduction. In addition, mine workings are moving deeper, which results in increased ventilation control issues such as higher total and respirable dust levels, greater seam gas contents in parallel with lower in situ permeabilities, spontaneous combustion and heat management issues. A comprehensive database of Australian LW ventilation practice is analysed. Currently there are a variety of LW panel ventilation circuits used in Australian underground coal mines due to various combinations of seam characteristics, gas emission rates, spontaneous combustion, geological features and surface constraints. The main issues usually addressed in the designing and planning of ventilation circuits for LW panels are airway velocity, gas concentrations, LW cutting methods (eg Bi-di, Uni-di or half web), ventilation of control devices, pressure differentials and leakage paths and understanding gas concentrations across the length and width of the goaf. If the ventilation circuit can manage the applied contaminant load (gases, heat and dust) at an acceptable cost and circuit duty, then supplementary controls, such as gas drainage, refrigeration and dust sprays and scrubbers, may not be required. CITATION:Gillies, S and Wu, H W, 2013. Review of Australian longwall panel ventilation practices, in Proceedings The Australian Mine Ventilation Conference , pp 87-94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

The performance of the Australian Mining Industry over the past 10 years using key indicators of production, revenue, aftertax return investment, together with key cost elements, market changes and ore reserves is briefly reviewed. The elements of competitiveness are discussed forthe industry and the effects of Government charges and policies relating to existing operations are outlined. There is a demonstrated need for improvements in competitiveness in direct and indirect costs and for improved access to resources for the mining industry to continue to grow and add to Australia's economic growth.

Jan 1, 1987

By D Xiong, G Xu, L Yao, F Wang, Y Duan

The goal of this project has been to digitise and use drill parameter data from rotary drilling (measurement while drilling; MWD) for a more effective planning of the blasting process in surface mines. A more accurate and reliable digital drilling and automatic hardness identification technology was developed, which includes both a hardware and software system. In the aspect of hardware, we designed a positioning, navigation and hardness perception terminal system which consists of a global positioning system original equipment manufacturer board, programmable logic controller and sensors of measuring major parameters, and a wireless data transmission system which combines digital blasting platform and wireless transmission facilities. In the aspect of software, we developed the navigation software of locating blastholes using LabVIEW and C++, and the blasthole design software using AutoCAD ActiveX (C#) technologies. This new technology is applied at Jiangxi Dexing Copper Mine, and initially realising the digitisation of drilling and hardness identification in blasting zone.CITATION:Duan, Y, Xiong, D, Yao, L, Wang, F and Xu, G, 2015. Advanced technology for setting out of blastholes and measurement while drilling, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 593–598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J Westh, S Rashleigh, L Gallagher

Mining companies are moving towards automated haul trucks and other equipment. One reason for this is that if automated trucks can operate in a standard pattern over and over again without variation, then human error is reduced, if not eliminated.The challenge for mining production leaders/managers is to ensure operators follow standard operating procedures for load and dump operations, with each operator doing the same thing, every time. However, operators are only human and inconsistent performance is rife at every mine site. The finger may be pointed at the operators for not doing as instructed. The clarity and variability of trainer instructions may be considered causal to the problem. Herein lies the problem. Almost all operators believe they are following the procedure very closely; moreover, they all demonstrate a strong desire to conform to instruction.Using video analysis and feedback, each operator can be shown where and by how much they differ from the benchmark set by their company. Operators, often for the first time, can see definitively what they are doing, compared to industry best practice.The technology utilised by real-time video (RTV) crews measures time, distance and angles. It can overlay the video of the operator at the load site, with video of the perfect pass. Operators are amazed when they see how near to, or how far they are from best practice.The footage and data gathered by RTV assists operators in understanding exactly what adjustments are required to increase proficiency. It also assists load and dump superintendents to identify where in the process they are losing time. When translated to overburden removal or mineral/resource extraction, the result is large production economies without the need for large capital investment in new automated technology.CITATION:Westh, J, Gallagher, L and Rashleigh, S, 2012. Improving safety and mine productivity using real-time video technology, in Proceedings International Mine Management 2012, pp 173-188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By S G. Li

Mine intelligent ventilation is an important guarantee to realise intelligent mining. It is the integration of the Internet of Things, big data, artificial intelligence, internet, cloud computing with ventilation technology, forming a complete ventilation system with intelligent perception, intelligent decisionmaking, intelligent emergency response and airflow control. In order to fully grasp the progress and trends of mine intelligent ventilation research in western China. The paper based on literature analysis and field application research, comprehensively expounds the main research and practical results of mine intelligent ventilation in western China, mainly analyses the development status of key technologies such as accurate and rapid determination of mine ventilation parameters, intelligent analysis and decision-making of ventilation and intelligent regulation of ventilation equipment, and introduces the field test or application of mine intelligent ventilation technology in western China. It lays the foundation reference for related research and improving the intelligent level of mine ventilation.

Oct 12, 2022

By B Olsson, B Reynolds, R Norman

An unprecedented growth in demand for coal exports has placed pressure on multi-user coal chains to guarantee that their capacity expansion projects will meet the required demand. These projects, however, are taking place in an increasingly complex commercial and technical environment - competing rail and coal terminal service providers as well as a myriad of competing mine operators, all needing to operate in an increasingly integrated manner to get the most out of expensive shared assets.Increasing system complexity and integration has driven the need for more holistic and sophisticated analysis tools. The capacity of coal chain subsystems, such as mine, rail and port, can no longer be determined effectively in isolation. Understanding the nature of the interactions between these subsystems, their sensitivity to uncertainty and the resultant capacity of the integrated system is the key to both maximising value and minimising risk.Recently, TSG has worked closely together with the Integrated Logistics Company and a number of key stakeholders in the Dalrymple Bay Coal Chain to develop independent system master plans. These master plans have provided a quantitative and rational assessment of coal chain capacity in its current state and a prediction of its capacity once a pipeline of committed capacity improvements is in place. This paper provides an overview of the study and a comprehensive guide to the process required to effectively achieve valuable strategic insights in a challenging multi-user stakeholder environment.CITATION:Reynolds, B, Olsson, B and Norman, R, 2012. Using independent system simulation to mitigate risk in the Dalrymple Bay Coal Chain, in Proceedings Project Evaluation 2012 , pp 77-84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By A Giblett, B Putland

This paper provides a simple guiding framework for grinding circuit optimisation, focussing on common themes in past optimisation success stories, the conditions for success and techniques that can be employed to identify and define opportunities. Many significant grinding circuit improvements have been reported for operating plants, based on recurring themes such as the optimisation of mill feed size, mill liner design, process control, critical size, grinding media and classification. The paper condenses these experiences into a set of simple questions for the operator to ask, and provides guidance towards identifying and achieving the optimisation goals.CITATION:Giblett, A and Putland, B, 2018. The basics of grinding circuit optimisation, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 129–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018