Search Documents

By Wesley, Worner H

During the meeting of the Institute last year at Port Pirie, the opportunity was taken to sample the lead bullion coming from the blast furnace and various stages during the refining process. Also, in the desilverising section, the upper zinc rich phase was sampled as the silver content built up and in the cupellation operation a series of samples was taken as the silver content of the bullion increased. In these two cases, the samples were taken under the supervision of a member of the staff of the Broken Hill AssociatedSmelters.In the following account of the microstructure of the samples taken, only the main phases present have received attention. In this connection deduction from phase diagrams of binary alloys has been used in conjunction with the assays carried out on duplicate samples taken at the same time as those for micro examination.

Jan 1, 1938

At an early stage of the examination of most prospects, samples are taken; and the sample values obtained play an important part in determining the subsequent history of the prospect. It is, therefore, important that. eveJJy effort should be made to interpret asfully as possible the meaning of the observed results. In this connection, it is suggested that examination of the assay values of mine samples by simple statistical methods may bring to light information of considerable value, which might otherwise be missed.Although expert statisticians may derive more information from the available data, those who are, like the writer, less proficient mathematically, may also benefit by applying quite simple statistical methods. At least they will develop a useful habit of thought bywhich they become aware at all times that sampling results only provide estimates of the truth, but that an assessment of the precision of such results may be possible. The object of this paper is to provide some evidence of. the truth of these statements, by theuse of a few very elementary statistical calculations.General.The idea that any mine sample is subject to error from a variety of causes is a very familiar one. Doubt always exists with regard to the representativeness of a perfectly cut sample, and other errors may arise through imperfections of sample cutting, crushing, splitting and assaying. Some causes of error may give rise to "constant" errors, others may cause variable but one-sided "systematic" errors, and others again may bring about variable results without any tendency toward bias on the average. In statistical language, mine sample values are subject to errors which may have either assignable causes or chance causes. The former are those which can be isolated, or should be capable of isolation, while the latter are those remaining when all assignable causes have been removed. A single constant assignable cause brings about bias in all results, and one or more than one variable assignable cause brings about variation between individual results and perhaps an overall bias. The system of chance causes that would remain if all assignable causes were removed would cause variation between individual results but no overall bias. There is no sharp practical line of distinction between the two types of cause) of error; nor is it ever possible by any method of statistical analysis to be certain that there are no assign...

Jan 1, 1950

By J Samosir, L Snyman

Northparkes was the first mine in Australia to use block cave mining method which relies on gravity and natural rock stresses to fragment and recover the ore. It was also the first hard rock mine to use hydraulic fracturing, in conjunction with CSIRO, to promote caving of E26 Lift 1. The technique was later used on E26 Lift 2 wedge and E48 prior to undercutting.Northparkes production is currently sourced from the E48 Lift 1 block cave mine and E26SLC. The E48 block cave contains economic ore to the north and south of the current cave footprint. To recover this ore the footprint has been extended on the north and south with two extraction drives and one extraction drive, respectively. Modelling of cavability above the additional drives indicated that the cave would not readily propagate to a sufficient height of draw to mobilise the ore and tended to arch over into the existing cave. To address the modelling results and to reduce the risk of the project, rock mass preconditioning was adopted.This fracturing campaign was performed from surface drill holes adjacent the subsidence zone angled to intersect the higher grade and higher elevation ore zones.Optical televiewer surveys, run prior to fracturing, picked intervals and fault zones to be avoided. Holes were resurveyed post-fracturing to detect newly created fractures and as a measure of success of the program.During fracturing operations water and gel fractures were run at varying depths and pumping pressure was logged for each fracture. The mine seismic system monitored significant events and dye in the fluids utilised for tracking water inflow locations during underground inspections.Towards the end of the project, guar fibres from gel were detected within the mill circuit and required treatment to resume optimum processing.CITATION:Webster, S, Snyman, L and Samosir, J, 2016. Preconditioning E48 cave extension adjacent to an active cave, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 471–478 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Residual aeolian placers (RAPs) are formed by the wind, by preferential entrainment and removal of small and low-density detritusfrom a pre-existing, typically sedimentary sequence containing heavy minerals. Heavy minerals that are resistant to chemical alteration and either soft and malleable (gold), or extremely hard (diamond, sapphire, ruby, etc), are concentrated as a residual on the wind deflation surface, typically in the interstices between larger resistant clasts. RAPs form preferentially in arid or semi arid areas, where the vegetation is sparse or absent, and where topography and surface gradients are low, but may also form on beaches and in periglacial environments. RAPs consist of a continuous or discontinuous, planar or gently undulating horizon of heavy minerals in a single-clast-thick pavement of resistant pebbles, cobbles, or boulders, which mantles the present topography or palaeo-topography. Extreme wind erosion and surface deflation may condense the full pre-existing sequence into a layer of heavy minerals only. The grade of RAPs is substantially higher than in the precursor deposit, and commonly much higher than those typically found in most other placer types. Aside from their general occurrence as a thin pavement of resistant clasts, the best indicators of residual aeolian gold placers are the presence of wind-eroded stones (ventifacts) on the pavement, and the distinctive and unique shapes of aeolian gold grains themselves. The shape of the gold grains is progressively transformed by sand blasting during placer development, from grains with thickened rims, to toroidal grains on which the rims are æsplitÆ and peened inward toward the grain centre on one or both of the grain sides, to hemispherical or sub-spherical grains that are fully encapsulated by the in-turned rims. Gold that has undergone aeolian shape transformation is difficult to entrain and transport away from the site of aeolian concentration by anything other than mass movement or glacial processes. It is also easily retained by commercial recovery plants of any configuration.

Jan 1, 2004

By T A. J Hopper, B J. Birt, K K. Trofimczyk

Nuclear magnetic resonance (NMR) has been utilised in the oil and gas industry for over 60 years. The technology was recently identified as having potential value in iron ore, where latent bound moisture may affect ore handling even after dewatering and extraction. The first step in introducing this technology to iron ore involved laboratory tests on drill core samples. These results established the parameters for a downhole borehole magnetic resonance (BMR) tool for iron-rich environments, which was subsequently developed. A major challenge involved shrinking what is a very large tool in the oil industry to a slimhole, lightweight, 1-man deployable mining tool.Of primary concern was the ability to measure the very fast transverse relaxation times (T2s) seen in the lab results on iron ore samples. Iron creates local field gradients that significantly decrease the T2 times. As a result, the BMR tool had to be able to measure T2s in the range of hundreds of microseconds, a level not required in clastic sedimentary formations. The choice of T2 cut-offs in iron ore is critical to successfully separating the free and bound fluids. The industry has typically focused on T2 cut-offs in clastics and carbonates, but not in systems with high iron content. Using core analysis results (poro-perm and NMR) we were able to verify the BMR response. The T2 cut-offs were determined from NMR core analysis and then applied to the logs so as to provide a continuous, calibrated permeability log.Field results that highlight the challenge involved in logging in iron-rich environments are presented, as well as some minimum requirements for a successful BMR log. Examples from boreholes in an active iron ore mine in the Pilbara iron ore province in Western Australia are presented, as well as explanations for how NMR data can be combined with bulk density logs to provide a continuous dry weight density log based on the original density-porosity equation from Alger et al (1963).CITATION:Hopper, T A J, Trofimczyk, K K and Birt, B J, 2017. Development of a slimhole downhole nuclear magnetic resonance tool for iron ore – some applications and limitations, in Proceedings Iron Ore 2017, pp 473–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Study on Mineral Processing for a Cassiterite Ore in Southwest China

Sep 13, 2010

The following brief observations on the mineral composition of the Mt. Oxide copper ore are intended to supplement the geological description of that ore-body recently published by Blanchard (2).'" The Mt. Oxide copper mine is situated about 45 miles W.N.W. of Dobbyn, in the Cloncurry district of Queensland (Fig. 1). A representative suite of specimens from the mine was obtained through the kindness of Mr. P. B. Nye, Executive Officer of the Aerial, Geological and Geophysical Survey of Northern Australia, and Mr. Jack Hall, the tributor of the Mt. Oxide mine. The specimens, as shown in Fig. 2, were nearly all from the sulphide zone, between the l04-ft. level and the 300-ft. level. Several additional specimens, together with information which will be referred to later were kindly sent to me by Mr. Roland Blanchard.MINERAL COMPOSITION OF THE COPPER OREThe mineral composition of the ore is relatively simple. It consists essentially of chalcocite, with varying, but minor figures...

Jan 1, 1940

The Golden Ridges Mine, one of the properties of New Guinea Goldfields Limited, is situated on the right bank of Nami Creek, not far from the township of Wau, in the Territory of New Guinea.The property is somewhat unique, in that the goldbearing ore-body occurs in the form of a flat seam-like deposit lying on a volcanic breccia, and covered with a mantle of overburden of decomposed porphyry. The overburden varies in thickness up to a maximum of about 65 ft.The ratio of overburden to ore is about 3 to 1. The practice developed is to strip the overburden by hydraulicking, and to mine the exposed ore under open-cut conditions, blasting to a vertical face, and using electrically operated scraper hoists for conveying the broken ore to the mill bins.The stripping of the overburden involves the boring of well-drill holes, blasting the holes and then hydraulicking the shattered material.

Jan 1, 1934

Vein swarms in metamorphic terranes such as the Otago Schist Belt, New Zealand provide evidence of past hydrothermal flow systems leading to fault initiation and reactivation. A major episode of hydrofracturing and fluid redistribution occurred during early Cretaceous exhumation of the schist belt. As a result, presently exposed lower greenschist facies greyschists in NW Otago are pervaded by abundant quartz-filled hydraulic extension fractures with associated normal faults hosting quartz¦scheelite¦gold mineralisation. Once the effects of Cenozoic folding have been removed, a regional subhorizontal schist foliation contains an aligned array of subvertical hydrofractures striking NNW, striking parallel to a set of low-slip conjugate normal faults; the array extends over an area >1500 km2 and over a depth interval >5 km. The hydrofracture array comprises a mesh of interlinked extensional-shear and pure extension veins. These veins show mutually cross-cutting relations. Extensional hydrofracturing apparently preceded the development of major throughgoing normal faults. Low-displacement normal faults are infilled with laminated quartz (¦ scheelite) veins (

Jan 1, 2002

By A Croll

A panel cave using LHDs for ore extraction came into production at Premier in 1990 at a depth of 630 metres below surface on the western side of the mine in the BA5 mining block. A post-undercut mining sequence was used with all development on both the undercut and production levels completed prior to the undercut being advanced over the pre-developed drawbells. Support and rock mass damage on the production level was extensive as the undercut moved overhead. Undercutting and coarse fragmentation created problems. The mining sequence was changed to an advance undercut with the minimum of development and support undertaken on the production level prior to the undercut moving overhead. Only once the abutment stresses had stabilised were drawbells developed and final support installed. The height of the undercut drill design was decreased from 18 to 13 metres. The changes resulted in markedly less rock mass and support damage on the production level. Lessons learned in the BA5 mining block on the 630 level were incorporated into planning and scheduling the BB1E mining block which came into production on the 732 metre level on the eastern side of the mine in 1996. An advance undercut mining sequence was planned, undercut height was minimised and undercutting parameters were optimised in terms of the BA5 experience. Numerous problems still occurred. As the undercut area increased in size severe spalling from the cave back resulted in vertical propagation of the cave to a height of 30 metres instead of the planned 13 metres. The resultant coarse fragmentation created secondary blasting problems and an excess of undercut ore that had to be loaded and trammed, slowed the rate of undercut advance. The planned mining sequence was compromised and considerable support and rock mass damage resulted on the production level below. Once these problems had been overcome the undercut advanced at the planned rate and continuous caving initiated at the predicted hydraulic radius. At a later stage the unexpected ingress of water hampered undercut drilling and slowed the rate of undercut advance in a section of the cave. Leads and lags between adjacent tunnels and the overall face shape could not be developed as planned. The rate of natural horizontal cave propagation exceeded the rate of undercut advance and three undercut drilling tunnels were extensively damaged. More tunnel development on the production level prior to undercutting than was planned resulted. The slow advance of the undercut and high abutment stresses caused extensive damage to installed support and the rock mass on the production level, 15 metres below. Experience in the BB1E mining block on the 732 metre level has taught that an advance undercut mining sequence reduces damage on the production level markedly. Extremely tight control on the rate of undercut advance, leads and lags between adjacent tunnels and overall undercut face shape as well as extraction ratio, tunnel development and support sequence on the production level below is required. Premier Mine plans to implement a block cave at a depth in excess of 1000 metres within the next decade. All the experience gained on current mining levels together with data collection and numerical modeling is being used to plan the proposed mining operation. The geotechnical challenge of mining at this depth in weak rock has been identified as the greatest risk to the project. Challenges centre around adopting the correct mining sequence, limiting the extent of rock mass damage associated with undercutting and effective support. The hydraulic radius needed to initiate caving, fragmentation, drawpoint spacing, secondary blasting and the possibility of seismicity are geotechnical concerns that are being addressed. Results to-date suggest that a pre-undercut mining sequence with all development and support on the production level carried out only after the undercut abutment stresses have passed overhead will have to be implemented.

Jan 1, 2000

By B S. Utting, W J. Cowie

The alluvial gold industry of New Zealand is based on the placer deposits in Otago and on the West Coast. Production from these since discovery in the 1850s has been an estimated 480 t (15 Moz) of gold. Annual output has expanded continuously since 1980 and is expected to be over 2 t of gold for 1989. Following a historical review, the characteristics of typical operations, which use hydraulic excavators and mobile trommel units are discussed. Descriptions are then given of alluvial activities in Otago and on the West Coast.

Jan 1, 1990

By Hudson S. B

With a particular electrode configuration, and a particular combination of electrode voltage and roll speed, a relatively small increase in electrode voltage, or a relatively small decrease in roll speed, resultsin a marked improvement in the separation of zircon from ilmenite. In general, fine minerals can be separated using a higher roll speed, or a lower electrode voltage, than is required to separate coarse minerals. The ionizing electrode should be reasonably close to the point at which mineral is fed on to the roll, and nearer to the roll than the non-ionizing electrode. The optimum conditions for the separation of zircon from ilmenite may not apply for the separation of other non-conductors from other conductors.INTRODUCTIONAlthough the high tension separators used in the Australian beach sand industry are efficient, this efficiency has been gained very largely by a process of trial and error, and not by a systematic study of the effects of changes in the operating variables. The optimum roll speed for a particular electrode position and electrode voltage, and the optimum electrode voltage for a particular roll speed and electrode position, can both be determined quite readily. It is not so simple to determine the optimum electrode position for a particular electrode voltage and roll speed. The reason for this is that the electrode used in high tension separators consists of two parts-an ionizing and a non-ionizing electrode respectively. The angular and radial positions of these electrodes, relative to the feed roll and to each other, affect the behaviour of conductors and non-conductors to varying degrees.

Jan 1, 1962

By L D. Queen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Tifalmin porphyry copper district is located in the Star Mountains roughly 35 km north-east of the Ok Tedi mine. The district is a cluster of temporally and geochemically related porphyry copper deposits and their associated skarns. It covers an area of roughly 10 × 6 km and comprises at least three intrusions (Olgal, Futik and Kum Kom) where drilling has demonstrated the presence of porphyry copper mineralisation, and another three intrusions (Rattatat, Unfin and Pad 48) where porphyry copper mineralisation is strongly suggested by surface investigations and geochemical or geophysical signatures.Copper and gold mineralisation was first discovered in the area in the 1960s as part of the regional exploration program by Kennecott that located Ok Tedi. The mineralisation is associated with poly-phase porphyritic diorites, quartz diorites and tonalites that intrude the Upper Eocene to Middle Miocene Darai limestone and underlying Cretaceous to Eocene Feing Group. Radiometric K-Ar and U-Pb zircon ages cluster between 4 and 2 Ma for both the mineralised and post-mineral intrusions. In addition to porphyry-type mineralisation, variable amounts of calc-silicate and/or magnetite skarn occur near the contact of most of the intrusions. Mineralisation in the Olgal and Futik porphyries occurs as chalcopyrite replacement of mafic minerals and in a stockwork of micro-veinlets. Mineralisation mostly occurs in the intrusions but is also observed in hornfelsed siltstones and sandstones of the Feing Group on the southern margin of the Olgal intrusive body. Quartz veining is uncommon. Secondary magnetite is commonly associated with the highest copper and gold grades. Sericitic alteration is most prominent in the mineralised hornfels. Structurally, the area is dominated by syn- to post-mineralisation thrusting from the north. At least one of the deposits (Olgal) appears to be truncated at depth by a thrust fault.CITATION:Queen, L D, 2015. The Tifalmin porphyry copper gold district, Star Mountains, Western Papua New Guinea , in Proceedings PACRIM 2015 Congress, pp 357–360 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Factors leading to the necessity for some individual testwork in solving most specific hydraulic transportation problems are listed and a description is given of a method used in determining critical flow conditions. An outline is given of the basic theory of the purpose of the testwork, and a means of applying test results for varied pipeline diamet.er and material conditions follows. Engineering and economic factors are applied to the solution of a specific hydraulic transportation problem and the use of the test results in plant practice is illustrated. The advantages of connecting pumps in series in centralised pumping stations rather than individually along the pipeline are stressed. Some notes are added on the future possibilities and economies of post pump injection of solids into high pressure pipelines.THE HYDRAULIC TRANSPORTATION OF SANDSAs well as all the classical variables involved in a pipeline installation, one must consider, when solids are to be transported, the effects of such variables as:(i) Proportion of solids in the pulp.(ii) The average specific gravity of the pulp.(iii) Specific gravity of the solid material.(iv) Solid particle average sizing and possibly shape.(v) Solids particle grading.(vi) Pipeline diameter for effects other than classically hydraulic.(vii) Pipeline material.(viii) Fluid viscosity.(ix) Pump characteristics.(x) Abrasive or corrosive properties of the pulp.Not surprisingly, the application of published data to the hydraulic transportation of a specific material is difficult if not well nigh impossible. Most hydraulic transportation investigations also involve economic and site factors vary...

Jan 1, 1959

By M J. Bourassa

In addition to the geologic risk of a particular project, the criteria that an international exploration company (æIECÆ) utilises when making an investment decision in a particular country should also include a critical analysis of the political, judicial and fiscal regime of the host country. A key investment criteria of an IEC is mineral tenure and the security and continuity of that mineral tenure under the host countryÆs existing legal system as well as the host countryÆs overall legal, political and fiscal framework, the latter of which can affect the projectÆs overall economic viability in a number of ways. The authors, Steve Vaughan and Michael Bourassa of Aird & Berlis, Toronto, Canada, have taken the position that developing an understanding of a countryÆs legal tradition is a crucial first step in analysing the mineral regulatory regime of a particular country. This paper continues their efforts to overview the most recent legal trends affecting the worldÆs mineral industry and attempts to analyse, categorise, compare and contrast differing legal systems, cultural backgrounds and economic philosophies relating to the development of mineral rights in Pacrim countries and the resulting commercial, legal, and political framework which ultimately drives the relevant mineral legislation. For the convenience of organisation of this analysis, the authors have divided the Pacrim countries into four smaller groups, firstly, on the basis of their legal tradition and, secondly, by their geographic location:Common Law Countries: USA, Canada, Australia and New Zealand; Spanish Civil Code Countries: Mexico, Central America (Panama, Nicaragua, El Salvador, Guatemala), South America (Chile, Peru, Ecuador, Colombia). Communist or Former Communist Countries: Mongolia, China, Russia. Countries of the Pacific Southwest: Phillippines, Indonesia, Malaysia, Indo-China (Vietnam, Laos, Cambodia, Thailand), Papua New Guinea. The discussion starts with an analysis of the various types of legal regimes, attempts to classify or categorise them, reiterates the necessity for the rule of law and those factors which encourage mineral exploration and development and discusses and recommends the expansion of a practical country competitiveness rating system developed by the Fraser Institute. In addition to the fundamental issue of mineral tenure û what it is and how secure it is û the paper discusses how different legal systems have shaped different approaches taken by individual nations to attract foreign mineral investment. The paper analyses the best practices and experiences accumulated in different Pacrim countries with varying legal traditions and identifies a practical country competitiveness rating system which the authors believe should be expanded to cover all minerally endowed countries. This rating system will permit countries to identify their mineral regime weaknesses and adjust their legal systems to better attract mineral investment and will also permit exploration and mining companies to compare their jurisdictional choices with those selected by their competitors.

Jan 1, 1999

By Lyon R. J P

The quartz-cassiterite-wolfram veins at the Aberfoyle Tin Mine, north-eastern Tasmania, form a sheeted zone about 200 ft. wide and 1,600 ft. long in slightly contact metamorphosed shales, slates and greywackes, and are associated with a cupola of aplitic granite whose top is about 1,050 ft. below the present surface. Economic mineralization persists from the surface down to a vertical depth of 1,050 ft. to 1,100 ft., dying away in the vicinity of the cupola. Down to the 9-level there is a progressive increase in wolfram content of the veins, and a decline in cassiterite content, with increasing depth.The veins are banded or zoned, with a seivedge of muscovite on the wall. Cassiterite, wolfram and sphalerite occur inside the selvedges, projecting into a core of quartz of varying width. Other sulphides form the central part of some narrow veins, or occur as clots in the quartz. The general sequence of deposition of the ore minerals was: (1) cassiterite, wolfram; (2) arsenopyrite, pyrite, molybdenite; (3) pyrrhotite (in part); (4) blende-group minerals-chalcopyrite, sphalerite, stannite, pyrrhotite (in part)-as solid solutions; (5) galena, tetrahedrite, matildite, native bismuth, scheelite; (6) marcasite and secondary pyrite, magnetite and hematite. The sequence of deposition of the gangue minerals was: (1) fluorine-bearing minerals-muscovite topaz, apatite, triplite, fluorite-more or less contemporaneous with the cassiterite and wolfram;' (2) quartz-contemporaneous with the earlier sulphides; (3) carbonates--contemporaneous with the later sulphides. The stages overlapped somewhat.The composition of the sphalerite and heat treatment experiments with the solid solutions indicate that the blende-group sulphides were deposited at about 6000 C., and cooled rapidly, so that unmixing of the solid solutions was arrested. This accords with the likelihood that the country rock temperature was not above 2000 C. Annealing experiments at between 3500 C. and 6000 C. led to further precipitation from solid solution at the lower temperatures, and to significant segregation by solid diffusion within, a week, indicating that both deposition and cooling of the ore were rapid processes-completed in a matter of days. Since the mineralizing solutions must have lost some heat during...

Jan 1, 1957

By D Syme

In the middle of 2000, BHP Billiton implemented a Six Sigma Plus business improvement program known as Operating Excellence. It was developed based on a business bottom line initiative to deliver 35 - 40c/share and was one of the BHP Billiton strategies to deliver $2 earnings per share and a longer term $40 share price (BHP share price). Cannington is a silver, lead and zinc mine owned and operated by BHP Billiton. Through implementing Six Sigma Plus Cannington wanted to:have in-house capabilities to change and improve; tailor for the needs of each business unit and department; have æSharing of its KnowledgeÆ as a tool for improvement and have a competitive edge across Cannington û to be better than our competitors; learn from and leverage off the successes of improved safety and prior business improvement efforts; and ensure networking and sharing of information have common measurement systems across all assets. As with most business improvement programs û Six Sigma Plus was met with some degree of skepticism, especially given the amount of resources involved. After 18 months, much of this skepticism has been replaced with enthusiasm as peopleÆs understanding and acceptance of its fundamental concepts are being realised. The idea behind Six Sigma Plus is that it combines sound technical solutions with high acceptance by those who need to work with or implement the change. The future vision for Six Sigma Plus is that it become part of what we do at Cannington û just like safety and environment û so that Six Sigma tools and methodologies are used in our every day work.

Jan 1, 2002

Mining One (M1) is often challenged with the task of evaluating deposits considering open cut and/or underground (UG) mining methods. In many near surface deposits a combination of both methods results in the optimum economic means of exploitation. As common as it is to have open pit mines eventually develop into underground mines, theory associated with determining the optimum underground/open pit interface location continues to be subject to refinement. With recent developments in underground software packages, the generation of rudimentary underground mining stopes from basic economic inputs is not only fast, it provides a practical underground mining solution. The determination of the open pit/underground interface is not new to Gemcom's Whittle 4X (Whittle). However, its solution has only ever claimed to be indicative, mainly due the rudimentary nature of how Whittle represents any potential underground mining. The efficient generation of the aforementioned underground mining solution has provided mining engineers with a unique opportunity. Underground mining can now be represented within the Whittle environment to allow the open pit/underground mining scenario to be modelled with increased accuracy. Providing Whittle with the ability to now consider mineable underground stopes combined with the consideration of time value of money (discounting), has delivered a solution with higher credibility than ever before.This paper will elaborate on the potential value gains associated with improved accuracies in the modelling of any potential underground mining in the Whittle environment. Furthermore, it will explain the importance of incorporating time value of money in the optimisation process to provide a consistent solution through to pit selection and final analysis.

Dec 6, 2010

This paper describes the past, normal and advanced practice of optimisation in mining. It then discusses what needs to happen for the mining industry to make full use of what is now available.

Dec 6, 2010

By M A. Knackstedt

Coupling between deformation processes and rock permeability is a major factor influencing the architecture of fluid migration and the localisation of ore deposition in several types of hydrothermal ore systems in middle to upper crustal regimes. Permeability in many hydrothermal systems is controlled by a dynamic competition between deformation-induced porosity-creation processes and porosity-destruction processes. Localisation of deformation within faults, fractures and shear zones leads to flow localisation, with large-scale flow systems forming when active faults and shear zones link to create percolation networks. Numerical modelling techniques are used to explore the growth of fracture networks and evolution of network connectivity during progressive deformation. Initial results indicate that networks reach a percolation threshold at very low strains. Near the percolation threshold, flow is localised along a small proportion of the total fracture population and favours localised ore deposition. At higher strains, flow is distributed more widely throughout the fracture population and may provide reduced potential for production of high-grade deposits. The distribution of mesothermal gold deposits along a small subset of the total population of co-active faults and shear zones in the Archaean Yilgarn Craton in Western Australia indicates that some hydrothermal systems maintain themselves near the percolation threshold for a substantial part of the lifetime of the system. Fluid-driven growth of fault/fracture/shear networks may lead them to self-organise near the percolation threshold.

Jan 1, 1999