Search Documents

By Malcolm F. Hawkes, Robert F. Mehl

THE rate of isothermal transformation of austenite to pearlite depends upon the rate of nucleation, N, and the rate of growth, G, of pearlite in austenite.1.2 Values of N are given in terms of the number of nuclei forming in unit time per unit grain boundary area of unreacted austenite; values of G are given in terms of the linear rate of radial growth. Variations in the isothermal rate with temperature result from variation of -N and G with temperature. Depth of hardening of a steel depends fundamentally upon values of N and G; changes in carbon and alloy content effect changes in N and G and thus affect depth of hardening. Quantitative studies are available on N and G for the formation of pearlite in plain carbon eutectoid steels.3 Systematic studies in this field are necessary if the phenomena are to be well enough known to furnish. a proper basis for full rationalization and for theory. Accordingly, the studies are continuing, both with respect to the effect of alloying elements upon the values of N and G in the formation of pearlite, and to the values of N and G for the formation of ferrite in hypoeutectoid steels. The present paper is the first relating to the effect of alloying elements upon the values of N and G for pearlite. It offers special interest since cobalt is known to have an anomalous effect upon the rate of formation of pearlite, accelerating it, whereas all other elements retard it.' It will be shown that cobalt increases both N and G for pearlite and that this effect is inherent in the Fe-Co-C system and not dependent upon factors relating to austenite heterogeneity nor upon any recognizable adventitious factor. Inasmuch as the rate of diffusion of carbon in austenite and the interlamellar spacing of pearlite are variables related to G and possibly to N (in a manner not yet certain), measurements of the "effect of cobalt upon them are also reported here. In the course of the work, measurements were made on the effect of cobalt upon the martensite temperature and these are given. COBALT AS AN ALLOYING ELEMENT IN STEEL PROPERTIES OF COBALT Cobalt resembles iron more closely than does any other chemical element. Its atomic number is 27, hence it is the element immediately following iron in the periodic system. The two differ in atomic structure only in the fact that cobalt contains seven electrons instead of six in the third, or transition, level of the third shell. The next shell, which is the

Jan 1, 1947

By Sir Lowthian Bell

WITH the exception of air and water, it is open to question whether there is any form of matter which the human race could less easily spare than iron. Short of going the length of asserting that, without this metal for an anchor or steel for the compass, the adventurous navigator could never have crossed the wide Atlantic, we may credit the locomotive' and the steamer, and hence iron, for that sequence of events which has peopled North America with the

Jan 1, 1891

By W. A. Doble

Opinions differ as to whether the water-wheel almost universally known as the Pelton type belongs to the impulse, the tangential, the reactive, the jet or the percussion class, or to a cross between two or more of these classes. The fact is, that for an almost infinitesimal part of a second the axis of the jet of water strikes the bucket of this wheel at a true tangent to its base-line. The percussion of the water, striking the bucket, imparts an impulse to the wheel, causing rotation; and generally the bucket is so shaped that the direction of the jet is

Jan 1, 1900

By W. J. Keep

We have shown in former papers the influence which aluminum exerts when added to cast-iron, and we have presented in another paper, accompanying this one, the physical properties of the metal aluminum and of some of its alloys. The present paper continues the investigation. The reader will find, in our paper on "Aluminum and Other Metals Compared,"* explanations not here repeated, which will render the diagrams in this paper intelligible. The scale of stresses is laid off on the ordinate which rises from the zero-point of the diagram. The scale of deflections is laid off on the abscissa which runs horizontally through this zero-point. By applying a given amount of stress, then running back to zero, and again applying the same stress, we describe a spring-line, in which the deflections are proportional to the stresses. Generally the deflections exceed this proportion during the original application of stress; and the excess is the permanent set. By laying off from the zero-point a line parallel to the springline, we shall generally find that this new spring-line and the diagram coincide for some distance; that is, that the test-bar is

Jan 1, 1890

By T. M. Kegley, J. H. Frye, D. L. McElroy, M. L. Picklesimer, E. E. Stansbury

Measurements of rate of growth, thermodymmic quantities, and partitioning of Mn are reported for high-purity eutectoid Fe-C and Fe-C-Mn steels for the auistenite-pearlite reaction. Evaluztion of the cotnstants of a derived-rate equation with these data indicate that Mn additions cause the decrease observed by increasivg the activation energy and apparent activation entropy or the movenment of complexes at the interface. A diffusion-controlled mechanism is not required. Appreciable partitioning of Mn to cementite occurs entirely behind the austenite-pearlite interface for more than 30°C of subcooling. ThE growth of pearlite from austenite has been extensively studied over a period of years. but the rate-controlling step in the process is not known nor is the mechanisrn of the effect of alloying elements understood. A comprehensive review of the subject has been given by Mehl and Hagel. The present study has been concerned with further considerations of the effects of alloying elements on the rate of growth of pearlite. Analytical relatioriships for the rate of growth of pearlite have been considered by Zener.2 Turnbull,3 Machlin,4 Cahn.5 Frye,6 and Frye et a1.7 The derived expressions in each case involve the free energy of the transformation. the interlamellar spacing. and some rate term of the nature of the diffusion coefficient. mobility or frequency of occurrence of some rate-determining step. The treatments. of course. differ in detail. Further consideration is given in the present paper to the equation of Frye, Stansbury. and McElroy which was derived from modified absolute rate theory without in any way specifying the mechanism of the reaction. This equation is r=c ? T ? F exp -?E*/RT [1] where r = rate of growth in mm/sec c = a constant AT = equilibrium transformation temperature minus actual transformation temperature "C ?F = free energy per mol of austenite minus that of pearlite ?E* = activation energy R= gas constant ?F in Eq. [1] is computed from the following: ?F=?H?T/To - ?T' dT' ?T' ?CdT"/T" [2] To To where AH is the enthalpy per mol of austenite minus that of pearlite at the equilibrium temperature, To, and AC is the difference in specific heat between austenite and pearlite per mol. Subsequently, Darken, Fisher, and Galligan8 have reported that a layer of ferrite separates pearlite from austenite at the growing interface (i,e., the advancing face of Fe3C is in contact with ferrite, not austenite) and the ratio of the thickness of this layer to the spacing of the pearlite has not been found to vary with alloy content or transformation temperature. This observation does not require any alteration in the above equation: however, it may require that a different significance be attached to the factor, AT. The AT term appears in Eq. [I] as a consequence of a factor for the amount of growth per complex transformed at the interface.* It is based *This is not the sole reason for expecting such a relationship. See Ref. 7._______________________________________________________ on a l/2 ?T dependence of the interlamellar spacing. Zener2 has developed a theory which leads to Soa 1/?V where So = the pearlite interlamellar spacing. This relation is as consistent with the data on interlamellar spacing as other relationships, although, as pointed out by Mehl and Hagel,1 the data are not sufficiently precise to consider the relationship as confirmed. The work of Darken, Fisher, and Galligan8 requires that the above be written where f = the thickness of ferrite layer between austenite and pearlite. The present paper is concerned with iron-carbon-manganese eutectoid alloys and reports experimental measurements of the following kinds: 1) the effect of

Jan 1, 1961

By Robert Glass Cleland

IN SPITE of its widely ramified interests in manufacturing, mines, lumber, railroads, and real estate, Phelps, Dodge & Co. remained primarily interested in exporting and importing, in buying and selling, and William E. Dodge, the directing-partner, consistently styled himself a merchant. After 1849 the profits of the company mounted steadily for seven years until they approached the half-million mark, but in 1857 another severe panic ended the long period of national prosperity that had begun some fifteen years before. Extravagance, indebtedness, and inflation again took their costly toll; or, as the New York Herald of June 27,1857, declared: Governmental spoliations, public defaulters, paper bubbles of all descriptions, a general scramble for western lands and town and city sites, millions of dollars, made or borrowed, expended in fine houses and gaudy furniture; hundreds of thousands in the silly rivalries of fashionable parvenues, in silks, laces, diamonds and every variety of costly frippery are.only a few among the many crying evils of the day. The worst of all these evils is the moral pestilence of luxurious exemption from honest labor, which is infecting all classes of society. The country merchant is becoming a city stock-

Jan 1, 1952

By Theodore Simons

The rapid and comparatively recent development of flotation has opened so fascinating a field for study and research that the older processes of gravity concentration no longer receive the attention they deserve. The early work of Munroel and Richards12 and the more recent contributions by Clevenger and Coe,3 Laist and Wiggin,4 Ammon,5 Bardwell,6 Crowfoot,' and Hayden8 (to mention only some which have appeared in our own Transactions) and by Schu1z,9 have furnished so much data that to offer something new seems a difficult task. It is still possible, however, to present known facts from a different point of view, and, with this in mind, the writer has undertaken to express basic principles of gravity concentration in terms of simple mathematics and mechanics; the conclusions thus reached will be found to correspond, in general, with those obtained by experimental methods. Rittinger, in his classic Aufbereitungskunde (1867)) reached analogous conclusions by way of intricate higher mathematics, for which reason his interesting investigations have remained a sealed book to most of us. The writer hopes that a more elementary treatment of the subject, based in part on Rittinger's metheds, may arouse new interest in the study of basic principles.

Jan 1, 1923

By J. L. Sepulveda, R. F. Yap, R. Jauregui

INTRODUCTION The Third Theory of Comminution, oftentimes called the Bond Theory, was first published by Fred C. Bond in 1952. Since then, it has been widely used in the milling industry to size crushing and grinding equipment as well as to predict and evaluate their performance. Although two other comminution theories were advanced almost a century earlier, one by Rittinger, 1867, and the other by Kick, 1885, their use was limited because they did not agree with actual commercial comminution systems (Bond, 1961). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced in particle breakage, and equals the work represented by the product minus that represented by the feed. For particles of similar shape, the crack tip length is equivalent to the square root of one-half the surface area, and the new crack length is proportional to [(1/vT - vF)]; where P and F are particles diameter of product and feed, respectively. For practical calculations, the particle diameter can be expressed in terms of the 80% passing sizes, P and F, respectively. Therefore, the work input is given by, [10 _ 10', W = Wi [7P_7F(1)] Where W = the energy input to the mill, (kwh/t) Wi = Work Index, (kwh/t) P = square sieve opening which 80% of the product passes, (microns) F = square sieve opening which 80% of the feed passes, (microns) Equation (1) is the mathematical statement of the Third Theory, or the Bond equation. Numerically, the work index is the energy required in kwh/t to reduce a given material from theoretically infinite feed size to 80% passing 100 microns. The work index of a particular material is determined in the laboratory by conducting the standard Bond grindability test. Bond developed separate tests for the rod mill and the ball mill. The simplified test method described in this paper, which is used at Anaconda Research Center to approximate the work index, is an alternative procedure to the ball mill

Jan 1, 1982

By Theodore Simons

The rapid and comparatively recent development of flotation has opened so fascinating a field for study and research that the older processes of gravity concentration no longer receive the attention they deserve. The early work of Munroel and Richards12 and the more recent contributions by Clevenger and Coe,3 Laist and Wiggin,4 Ammon,5 Bardwell,6 Crowfoot,' and Hayden8 (to mention only some which have appeared in our own Transactions) and by Schu1z,9 have furnished so much data that to offer something new seems a difficult task. It is still possible, however, to present known facts from a different point of view, and, with this in mind, the writer has undertaken to express basic principles of gravity concentration in terms of simple mathematics and mechanics; the conclusions thus reached will be found to correspond, in general, with those obtained by experimental methods. Rittinger, in his classic Aufbereitungskunde (1867)) reached analogous conclusions by way of intricate higher mathematics, for which reason his interesting investigations have remained a sealed book to most of us. The writer hopes that a more elementary treatment of the subject, based in part on Rittinger's metheds, may arouse new interest in the study of basic principles.

Jan 1, 1923

By Franklyn W. Oatman

In order that the conditions which obtain in an oil well may be readily understood, a brief description of a typical California well and a number of the phenomena accompanying same will be given. That the necessity for the exclusion of water be realized, the effects of water intrusion, a description of methods of prevention, .and a discussion of causes of failure will be presented, followed by a summary and recommendations. Fig. 1 shows a section of a typical well which illustrates the relation of oil sands to overlying strata. It indicates a deep water sand separated from the oil sand by shale, and the proper place for the final shutting off of water. In this well a comparatively thick stratum of compact shale protected the oil from overlying water so that the operation of landing the water string was a simple matter. In some wells the protecting stratum may be only from 3 to 5 ft. thick and very careful operation is necessary in order to land the water string of casing properly and not puncture through to the oil sand. The cases just cited are common, but occasionally, after excluding overlying water, productive oil sands are drilled through in the expectation of finding more productive underlying sand, and a water-bearing stratum is tapped. In this case the problem is the reverse of the normal; water must be prevented from ascending rather than descending. A discussion of well-drilling methods is not within the scope of this paper, except such operations as pertain to shutting off of water. A brief outline of the several conditions which may accompany drilling follows. Some or all may be present in any particular case. The direct relation of these to prevention of intrusion will be discussed in detail further on. In drilling, the hole becomes more or less irregular in shape, and rough, and as the casing follows the bit into the well it does not fit snugly against the walls. As a result, water may descend between the casing and walls of the well. If a circulation pump is not used during drilling, the hole is simply punched through and the pulverized material removed from the well by means of a bailer. If circulation is maintained there is a continual flow of water down inside the casing and up around the outside between the pipe and the walls of hole. This keeps an open space around the pipe.

Jan 1, 1915

By S. A Weigand, J. W. Bolton

Production of sound bronze castings is a matter of great practical interest to users and manufacturers of high-grade non-ferrous engineering specialties. Although there has been much excellent research in this field, there still remains some confusion regarding the fundamental principles underlying production of really sound bronze. The literature of the past 20 years on this subject indicates that the prevailing opinion of metallurgists and foundrymen has been that unsoundness in bronze is due generally to oxidation. The following references are typical. Review of Literature Carpenter and Edwards1 state that when gun metal is melted the alloy dissolves gas, the amount increasing with rise in temperature and duration of the melting. The solubility of the gas diminishes during the fall in temperature and it escapes through the liquid metal. At the moment of incipient solidification there is an evolution of gas. Sperry2 says that by using charcoal a reducing atmosphere is supplied whereby oxidation is prevented, and this also prevents gases from coming in contact with the metal. Logan3 says that many of the troubles that occur in non-ferrous castings are the direct result of one thing—oxidized material. He mentions how readily copper absorbs oxygen when molten, but does not mention the harmful effects of reducing conditions as observed in overpoled copper. Guillemin and Delachana14 investigated the gases occluded in bronze and found that the better bronzes contained mostly hydrogen while the poorer ones had a larger proportion of carbon monoxide and carbon dioxide.

Jan 1, 1929

Abramovits, Charles, Student. Case School of Applied Science Cleveland, Ohio. '37 Adams, Benjamin C., Jr Address Wanted. '36 Adams, Ernest C., Student, Univ. of Illinois 908 W. Green St., Urbana, Ill. '35 Adams, George H. 4021 Walnut St., Riverside, Calif. '36 Afshar, Hodji Khan ?A. Box 2072, Norman, Okla. '35 Ahlen, Louis S., Student, Univ. of North Dakota Univ. Sta., Grand Forks, N. D. '37 Ahrenholz, Herman William, Jr., Student, Lehigh Univ Bethlehem, Pa. '35 Alger, Robert P., Student, Missouri School of Mines & Met Rolla, Mo. '36 Alkire, Robert L., Student, Univ. of Pittsburgh Pittsburgh, Pa. '37 Alleman, Virgil C., Student, South Dakota School of Mines Rapid City, S.-D. '37 Allen, C. G., Student, Case School of Applied Science Cleveland, Ohio. '37 Allen, Eugene S., Student, Univ. of California Berkeley, Calif. '37 Allen, George W., Student, Michigan College of Min. & Tech Houghton, Mich. '37 Allen, Harry Berkley, Student, Univ. of California Los Angeles, Calif. '37 Allen, Henry, Jr., Student. Univ. of Arizona Sigma Chi House, Tucson. Ariz. '37 Allen, Paul W., Student, Mass. Inst. of Tech Cambridge, Mass. '35 Allen. R. M.. Jr.. Student. Virginia Polytechnic Inst., "G" Co Blacksburg, Va. '35

Jan 1, 1937

By J. W. Bolton, S. A. Weigand

Production of sound bronze castings is a matter of great practical interest to users and manufacturers of high-grade non-ferrous engineering specialties. Although there has been much excellent research in this field, there still remains some confusion regarding the fundamental principles underlying production of really sound bronze. The literature of the past 20 years on this subject indicates that the prevailing opinion of metallurgists and foundrymen has been that unsoundness in bronze is due generally to oxidation. The following references are typical. Review of Literature Carpenter and Edwards1 state that when gun metal is melted the alloy dissolves gas, the amount increasing with rise in temperature and duration of the melting. The solubility of the gas diminishes during the fall in temperature and it escapes through the liquid metal. At the moment of incipient solidification there is an evolution of gas. Sperry2 says that by using charcoal a reducing atmosphere is supplied whereby oxidation is prevented, and this also prevents gases from coming in contact with the metal. Logan3 says that many of the troubles that occur in non-ferrous castings are the direct result of one thing—oxidized material. He mentions how readily copper absorbs oxygen when molten, but does not mention the harmful effects of reducing conditions as observed in overpoled copper. Guillemin and Delachana14 investigated the gases occluded in bronze and found that the better bronzes contained mostly hydrogen while the poorer ones had a larger proportion of carbon monoxide and carbon dioxide.

Jan 1, 1929

By E. R. Gilliand

KNOWLEDGE of a large number of the physical properties of the hydro-carbons is needed in the calculations and studies of the production engi-neer. Since experimental data on these properties of the individual hydrocarbons and their mixtures are available in only a relatively few cases, the use of generalized correlations has developed rapidly in the last decade. The generalized correlations of pressure, volume and tem-perature,1 enthalpy,2 and vapor-liquid equilibria,3 on the basis of reduced temperatures and pressures, are outstanding examples of this develop-ment. These correlations are of particular value to the production engineer interested in the flow of oil and gas, since they can be used to estimate the conditions under which segregation of phase occurs as well as the composition, density, and relative amounts of the phases. The technique of using the correlations for such estimations has been pub-lished by several authors¢ and will not be considered in this paper. A considerable number of data have been obtained to check the generalized pressure-volume-temperature correlations, and these data indicate that such relations hold for the hydrocarbons from methane to heptane. The accuracy is in general sufficient for most engineering pressure-volume-temperature calculations. However, the generalized correlations of enthalpy and vapor-liquid equilibria have in general been developed from the pressure-volume-temperature correlations by thermodynamic calculations and only a relatively few experimental data are available to check these calculated values. The calculations from pressure, volume and temperature are likely to lead to large errors in the calculated enthalpy and vapor-liquid equilibria. Thus, in the calculations of enthalpies, slopes of the pressure-volume-temperature data are employed, and determining these slopes can greatly amplify small errors in the original data. In the vapor-liquid equilibria calculations it is necessary to have the pressure-volume-temperature relations of the mixture, and the latter properties are much more questionable than those of pure components, particularly in the critical region. A considerable number of experimental data are

Jan 1, 1939

By M. Earl Volin, M. Adnan Goksel

The hydro thermal agglomerating process described (U.S. Pat. No. 3,235,371, 1966)* is different from the cotzventional high-temperature processes. Green pellets or briquettes made with mixtures of moist iron-ore concen- trates and burned or hydrated lime fines are hardened in an azttoclave at 198°C and under steam pressure for 112 to 5 hr, with or without previous drying. Under the neutral conditiotzs, oxidation of magnetite does not occur as in the conventional processes. The resulting azzlomerates-- are hard and resistant to abrasion and weathering, and they do not disintegrate in the Under test. The equipment required for the process is not complicated, and favorable operating costs are projected because of the low temperamre and efficient heat recuperation. A low capital investment makes the process attractive even when the annual pellet production is below a million tons.

Jan 1, 1970

By Edward Wisser

THE Pachuca silver district, situated about 100 kilometers northeast of Mexico City (Fig. 1), covers roughly the southeastern half of the Sierra de Pachuca. The latter is a mountain range with northwest trend, and forms a part of the northeastern rim of the topographic basin known FIG. 1.-LOCATION OF PACHUCA DISTRICT AND OTHER MINING CAMPS. as the Valley of Mexico. The length of the Sierra proper is about 50 km., its greatest width about 9 km., and it rises to a maximum of 600 meters above the general level of the basin floor. The Pachuca district consists of two contiguous subdistricts, the Pachuca area and the Real del Monte area. The center of the Real del

Jan 1, 1936

By R. T. Walker

GROUND waters-hot or cold-containing small amounts of the more common earth acids, such as carbonic acid, silicic acid, hydrogen sulfide, sulfurous acid and sulfuric acid, have only a very limited "solvent effect on dominantly siliceous rocks, whether of igneous or sedimentary origin, but in limestone they often form extensive cavities; and such "limestone caves" are the only openings of considerable size and continuity in rock formations that do not owe their existence directly and almost wholly to dynamic action. Limestone caves such as are developing at the present time must have been formed in all past geological ages in which limestone beds existed and where suitable conditions for the development of such caves prevailed; hence it would seem a reasonable expectation that, in the course of geological history, a certain number of ancient limestone caves must have been utilized as channels for the passage of mineralizing solutions, during portions of their course, at least, and that, in consequence, orebodies must have been deposited in such caves. Such a conception is not novel; it was proposed many years ago, but its possibilities, as explaining certain types of ore deposits, have been rather lost sight of in the development of the theory of the metasomatic replacement of rocks by minerals. It is the purpose of this article to assemble evidence to show that many of the orebodies found in limestone beds have been deposited in pre-existing caves; to discuss the criteria whereby such orebodies can be distinguished from others which have been formed along fissures and fracture zones traversing limestone, by the more common method of metasomatic replacement, analogous to orebodies in other formations; and to describe certain orebodies-particularly the "ore channels" of the Tintic district, Utah-as illustrative of the principles discussed. Limestone caves may be divided into two classes: those formed by cold, descending surface waters, which emerge again at some lower elevation as cold springs; and those formed by hot, ascending waters of deep origin or circulation, which attain the surface as thermal springs. Although these two classes are similar in many respects, there are certain characteristic and inherent differences whereby they can usually be distinguished.

Jan 1, 1928

By William Priestley

IN THE manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and elastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungsten, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured-by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. DESIGN OF GUN FORGINGS In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun are made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The elastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge.

Jan 12, 1921

By Daryl R. Tweeton, William H. Engelmann, Orin M. Peterson, Jon K. Ahlness, Gregory R. Anderson

The Bureau of Mines measured the geochemical changes as H2SO4 was used for in situ uranium leaching by Rocky Mountain Energy Company near Casper, Wyoming. Cores and ground water were analyzed before leaching. Water samples were taken from observation wells located between injection and production wells as the leach solution was brought up to full strength in several steps. Measurements were made of pH, Eh, temperature, conductivity, total dissolved solids, dissolved oxygen,HC03, U. V, Na, K, Ca, Mg,S04, CI, Mo, Mn, Fe, AI, Si, F, P, As, and Se. The data were gathered to assist in geochemical modeling of leaching and to study the potential environmental effects of acid leaching. Environmental considerations appear favorable. For example, the concentration of Se, a toxic element often found in uranium deposits, stayed below the EPA standard for drinking water.

Jan 1, 1979

By Charles M. Rolker

It is not my purpose to present a complete description, still less a thorough discussion from a theoretical stand-point, of the Leadville ore-deposits. Hence I have given to this paper the more modest name of " Notes;" since it is little more than a record of observations made three or four years ago, and now published from my original memoranda, with the view of preserving the facts rather than of

Jan 1, 1886