Search Documents

By A. W. Furbank

In reviewing the aerial cameras produced in different countries, it becomes apparent that in nearly all of them an attempt has been made to secure the greatest possible angle of view. This angle, of course, is determined by the objective. The objectives most commonly in use in aerial cameras have a maximum angle of 65". The objective developed for this new Zeiss camera combines freedom from distortion and brilliant definition, with an angle of 95". Aerial mapping, it is claimed, has been placed on a different economic basis, and new possibilities presented, particularly in connection with automatic stereoscopic plotting instruments, to which some short references are made. One way of enlarging the angle of view is to couple several instruments with their axes convergent, thereby producing a multilens camera. Typical of cameras of this sort in the United States is the Bagley four-lens camera, which later was developed into the five-lens camera (T3-A) of the U. S. Air Corps. More recently, in order to get away from the unfavorable Maltese cross image field of the five-lens camera, and to obtain a more practical form, two five-lens cameras were combined. By using them in tandem and rotating them by 45" relatively to each other, a ten-lens camera was produced, covering an octagonal ground area, with a total angle of view of 140". Similar designs have been evolved in other countries. In all of them, however, a number of difficulties have arisen, quite apart from their large weight and high cost. Because of their complex mechanism, numerous shutters and magazines, and the high precision with which these parts must be interadjusted and synchronized, these cameras are far from dependable. Moreover, a multilens camera by itself does not yet constitute a complete outfit for producing pictures suitable for photogrammetric survey. Because all the component pictures, except the central one, are obliques, it is always necessary to employ rectifying apparatus which transforms the marginal views to the perspective of the central one. In multilens cameras with many individual magazines, it is not convenient to

Jan 1, 1941

By Edwin S. Smith

Current research in the phenomenon of liquefaction has indicated some of the in situ material properties which should be considered in the planning of waste deposits. Practical experience in tailings disposal, however, must be combined with the results of theoretical and laboratory studies to develop the most economical and safe techniques against liquefaction failure. One of the many responsibilities of mining engineers and mill superintendents is providing for the safe and economic disposal of wastes (or tailings) that remain after a mineral has been extracted from an ore. The cost of disposal of these tailings exerts a considerable influence on the minimum grade of ore extracted from the mine. It varies to a great extent with each project and is dependent on many diverse factors, such as the local topographical, meteorological and seismological conditions together with the applicable water pollution laws of the area. The process used to extract a mineral from an ore determines the physical characteristics of the tailings and, thus, is one of the more important factors to be considered in the planning of disposal facilities. Today's trends in ore-processing operations complicate the problems of waste disposal: recently developed extraction methods result in the production of finer tailings, the use of lower grade ores produces greater volumes of wastes, and the enhanced land values in the vicinity of industrial plants preclude the former practice of spreading wastes laterally and force the expansion of waste deposits upwards to greater heights. The frequent occurrence of stability problems in waste deposits indicates that many mining organizations may not be employing current soil mechanics concepts and practices. One of the most spectacular, and often most disastrous, types of tailings dike failure is that resulting from liquefaction of the fine particles combined with a breach of the main retaining dike. TAILINGS DISPOSAL Since the many variations in site conditions, ore bodies and extraction processes dictate the general disposal procedures and mill superintendents incorporate special facilities to provide the most economical disposal method consistent with accepted safety standards, it is only natural that there are almost as many different disposal techniques as there are disposal areas. Methods used in the construction of retaining dikes include: (1) transporting granular material from an adjacent borrow pit and (2) mechanically segregating the total effluent and allowing the coarse fraction to form a retaining dike by hydraulic deposition. The location of a plant and the surrounding topography exert the greatest influence on the layout of tailings disposal facilities. Most of the above-ground waste deposits can be classified as side-hill, (Fig. 1,) cross-valley, (Fig. 2,) or stockpile deposits. Side-hill disposal areas are probably the most common type of layout because of the natural advantage of gravity flow, without the disadvantage of river diversion usually needed for tailings ponds formed behind cross-valley dikes. Stockpiles, which are placed on relatively level ground, require four retaining dikes and the effluent generally has to be pumped up into the disposal area. Changing production techniques or developments adjacent to disposal areas have produced variations or partial combinations of these three categories. In a series of articles, Lenhart describes many of the problems encountered in the disposal of tailings and certain innovations used to overcome them. He discusses weaknesses in design and layout and shows that disposal techniques are often learned the

Jan 1, 1970

By George A. Grandy, D. W. Fuerstenau

Simulation of nonlinear grinding systems is discussed in the context of the size-discretized batch-grinding model. A linear approximation of environment-dependent (or nonlinear) selection functions is postulated for systems which exhibit feed grinding orders less than unity. For this, a convex linear combination of zero and first-order selection function forms is used to obtain an analytical solution that can be used for simulation. An example in which marked nonlinear behavior occurs is rod-mill grinding. Accordingly, a series of grinding experiments was carried out in a batch laboratory rod mill to test these techniques; agreement between experiment and the model was found to be very good. Recently, significant progress has been made in the simulation of linear grinding systems by using a population balance mathematical model. Herbst and Fuer-stenaul presented a parameter estimation scheme that can be used with the size-discretized batch-grinding model, and Gumtz and Fuerstenau3 have extended these techniques to the simulation of locked-cycle grinding. Grandy et aL." summarized the simulation of linear systems and noted important alternate solutions to the batch-grinding equation. Kelsall et a1.'-" discussed the dynamic simulation of linear batch grinding, as well as linear open and closed-circuit grinding. In all of these, the key word is linear, which certainly restricts the engineer trying to simulate a variety of grinding systems. This paper discusses an approach for the simulation of non-linear grinding systems, particularly those which exhibit grinding orders less than unity. Experimentally, dry rod-mill grinding is used to evaluate the technique presented. Batch Grinding Model The size-discretized batch-grinding model has been discussed in detail by Mika et al.'.' and by Herbst and Fuerstenau,' and therefore, will only be briefly developed here. The model is formulated by making a differential mass balance of each size fraction in such a manner that the equation parameters are precisely defined in terms of selection and breakage functions,' which can be either calculated'.' or estimated1 from experimental data. The model is phenomenological because it averages all stress-application events in the system and, therefore, does not distinguish the manner in which individual particles are stressed.' For this average environment, the resistance of all particles in a size fraction to breakage is defined by that size-frac-tion's selection function; and when fracture occurs from an average event, the breakage product size distribution is defined again by that size-fraction's breakage function. The model is deterministic and is derived in terms of a continuous time variable and a discretized size variable,' i.e., the n mass fractions associated with the n defined size intervals (see Table 1 for nomenclature).

Jan 1, 1971

By Martin A. Mayers

Five-sixths of all the coal that is mined in the United States is burned, without previous treatment other than screening, for the production of heat and power, so that its value is fixed by its suitability for this purpose. Nevertheless, the characteristics of individual coals that determine their fitness for use in particular pieces of combustion equipment are not yet well known. This condition is due not only to the small extent of our knowledge concerning coal itself, but also to our comparative ignorance of the nature of the combustion process. The following paper is an analysis of the combustion process as it occurs in industrial furnaces, based largely on the results of laboratory research on combustion rates. From this analysis it is possible to determine the characteristics of the fuel that limit the capacity of a given piece of combustion equipment. Limitations imposed by other factors than the attainable speed of combustion will not be considered, since they are subject to a different type of analysis involving the balancing of maintenance costs against fixed charges. In order to observe the relations among the various factors that affect the speed of combustion, representative particles of fuel will be followed through two types of furnaces. A pulverized-coal furnace will be considered first, because the independence of the individual particles facilitates the analysis of the effect of furnace conditions. The second example will be a grate-fired furnace in which ignition of the fuel takes place on the underfeed principle. This includes both underfeed and chain grate stokers, (8)† but does not include hand-fired furnaces and some overfeed stokers. The furnace will be considered to be large enough, the temperature high enough, and enough air provided, to burn the fuel completely, without, for the moment, specifying these quantities more completely. Furnaces Burning Pulverized Coal In a pulverized-coal furnace, the fuel particle is carried, in a stream of air, into the furnace, where it is subjected to radiation from the flame and from the hot walls of the furnace. The increase of particle tempera-

Jan 1, 1936

By V. F. Parry, S. P. Burke

The presence of gas in coal mines necessitates the use of costly ventilation arrangements and the use of expensive mining methods. On the other hand, the gas itself in many instances is of considerable intrinsic value, and its separate recovery might conceivably be a profitable undertaking. This paper is concerned with a study of the movement of gas in coal strata with the object of determining the laws governing gas movement and thus making at least a preliminary step toward the solution of the more practical problem of its control or recovery. Naturally, so important a subject has received much attention from scientists and engineers. In most cases, however, the studies have been concerned with the origin1$, the amount" the composition3 and the method of retention4 of the gas in coal; or, from the more practical side, have been concerned with the phenonlena and conditions associated with outbursts5 or explosions and their control. Numerous studies also have been made of the permeability of coal to gas" of gas pressures measured in coal seams, etc. The authors are unaware, however, of any attempt to present a consistent or complete picture of the laws governing the movement of gas through the coal. Study in West Virginia A recent study conducted at this University7 gives the first presentation of the distribution of pressures in a small section of a coal seam. Holes were drilled into the coal rib to various depths and at various distances from the coal face. The location selected for study was as remote as possible from disturbing influences of mining operations, faults, "wants," etc. The pipes extending into the coal that were used to determine pressures were grouted into the borehole for the entire depth of the hole, and great precaution was taken to insure accurate pressure readings. A map of the geology of the region, a map of the probable boundary and extent of the coal seam, a current map of the mine and a

Jan 1, 1936

By John L. Boardman, C. W. Goodale

The motives behind the organization of the Bureau of Safety were twofold. First, there was the policy of the company toward its employees, which was one of fairness and consideration for their welfare and which entails the prevention of injuries; second, in order to prevent injuries, a study of their causes was essential, and this study could be made only by a thorough systematic classification of accidents, which required a special department to form and carry out the plans. The Bureau of Safety was organized to begin operation Jan. 1, 1914, hut practically all of the first year was spent in collecting data, making plans, etc. This department is semi-independent of others and reports directly to the president and general manager. It consists of the president of the company and the managers of the following departments: Mines, Washoe Reduction Works, Great Falls Reduction Works, Coal department, lumber department, B. A. & P. railway; and the chairman of the Bureau of Safety. Working under this group is the General Safety Committee consisting of the manager of mines, as chairman, the general superintendent, two assistant general superintendents, and the heads of the following departments: mechanical, geological, purchasing, sampling works, and framing plant; and also the safety engineer. Operating under the General Safety Committee are the group safety committees, consisting of the Anaconda group of mines, Boston & Montana group of mines, zinc group of mines, Washoe reduction works at Anaconda, B. & M. reduction works at Great Falls, coal department, lumber department and the R. A. & P. railway. Each of these group safety committces was in charge of the superintendent or manager of the group represented and the committee consisted of the foremen of the mine's or works that the committee served, as well as the safety engineer. These foremen and superintendents had met regularly for the purpose

Jan 1, 1923

By R. I. Jaffee, F. C. Holden, H. R. Ogden

IN a previous series of papers, the results of studies made on various types of high purity base titanium alloys were presented. Included in this work were the Ti-Mn' and Ti-Cu' alloys, representative of sluggish and active eutectoid systems, respectively. The present paper gives the results of a simi- lar study made on Ti-Mo alloys as an example of a ß-isomorphous alloy system. Experimental Procedures Alloy Preparation—Six ½-lb ingots were prepared from iodide titanium and high purity molybdenum stock. The ingots were arc melted in a water-cooled copper crucible under an argon atmosphere. Each ingot was melted at least twice to insure homogeneity and complete solution of the molybdenum. This was done by inverting the ingot in the crucible and remelting completely.

Jan 1, 1957

By P. W. Guild

DURING 1956 the application of geology and related scientific disciplines to the search for new mineral deposits went forward on an ever widening front. Spurred on by record-breaking consumption of many of the established commodities and new uses for minerals and metals that were hardly known a few years ago, the profession is figuratively leaving no stone unturned in the effort to insure that adequate raw material supplies will be avail- able for the future. More money was spent and more people were engaged along more lines of research than ever before. A huge project to map much of the Canadian Shield area by photogeologic methods stands at one extreme; application of isotope ratios to ore finding stands at the other; between them the more traditional techniques are being increasingly refined. In the Fiftieth Anniversary volume of Economic Geology, published late in 1955, Alan Bateman sketches the development of fundamental concepts as recorded in the pages of the journal over the first five decades. An additional 24 review articles cover individual aspects of the field and constitute a base for further advances.

Jan 2, 1957

By John L. Boardman, C. W. Goodale

The motives behind the organization of the Bureau of Safety were twofold. First, there was the policy of the company toward its employees, which was one of fairness and consideration for their welfare and which entails the prevention of injuries; second, in order to prevent injuries, a study of their causes was essential, and this study could be made only by a thorough systematic classification of accidents, which required a special department to form and carry out the plans. The Bureau of Safety was organized to begin operation Jan. 1, 1914, hut practically all of the first year was spent in collecting data, making plans, etc. This department is semi-independent of others and reports directly to the president and general manager. It consists of the president of the company and the managers of the following departments: Mines, Washoe Reduction Works, Great Falls Reduction Works, Coal department, lumber department, B. A. & P. railway; and the chairman of the Bureau of Safety. Working under this group is the General Safety Committee consisting of the manager of mines, as chairman, the general superintendent, two assistant general superintendents, and the heads of the following departments: mechanical, geological, purchasing, sampling works, and framing plant; and also the safety engineer. Operating under the General Safety Committee are the group safety committees, consisting of the Anaconda group of mines, Boston & Montana group of mines, zinc group of mines, Washoe reduction works at Anaconda, B. & M. reduction works at Great Falls, coal department, lumber department and the R. A. & P. railway. Each of these group safety committces was in charge of the superintendent or manager of the group represented and the committee consisted of the foremen of the mine's or works that the committee served, as well as the safety engineer. These foremen and superintendents had met regularly for the purpose

Jan 1, 1923

By V. F. Parry, S. P. Burke

The presence of gas in coal mines necessitates the use of costly ventilation arrangements and the use of expensive mining methods. On the other hand, the gas itself in many instances is of considerable intrinsic value, and its separate recovery might conceivably be a profitable undertaking. This paper is concerned with a study of the movement of gas in coal strata with the object of determining the laws governing gas movement and thus making at least a preliminary step toward the solution of the more practical problem of its control or recovery. Naturally, so important a subject has received much attention from scientists and engineers. In most cases, however, the studies have been concerned with the origin1$, the amount" the composition3 and the method of retention4 of the gas in coal; or, from the more practical side, have been concerned with the phenonlena and conditions associated with outbursts5 or explosions and their control. Numerous studies also have been made of the permeability of coal to gas" of gas pressures measured in coal seams, etc. The authors are unaware, however, of any attempt to present a consistent or complete picture of the laws governing the movement of gas through the coal. Study in West Virginia A recent study conducted at this University7 gives the first presentation of the distribution of pressures in a small section of a coal seam. Holes were drilled into the coal rib to various depths and at various distances from the coal face. The location selected for study was as remote as possible from disturbing influences of mining operations, faults, "wants," etc. The pipes extending into the coal that were used to determine pressures were grouted into the borehole for the entire depth of the hole, and great precaution was taken to insure accurate pressure readings. A map of the geology of the region, a map of the probable boundary and extent of the coal seam, a current map of the mine and a

Jan 1, 1936

By Martin A. Mayers

Five-sixths of all the coal that is mined in the United States is burned, without previous treatment other than screening, for the production of heat and power, so that its value is fixed by its suitability for this purpose. Nevertheless, the characteristics of individual coals that determine their fitness for use in particular pieces of combustion equipment are not yet well known. This condition is due not only to the small extent of our knowledge concerning coal itself, but also to our comparative ignorance of the nature of the combustion process. The following paper is an analysis of the combustion process as it occurs in industrial furnaces, based largely on the results of laboratory research on combustion rates. From this analysis it is possible to determine the characteristics of the fuel that limit the capacity of a given piece of combustion equipment. Limitations imposed by other factors than the attainable speed of combustion will not be considered, since they are subject to a different type of analysis involving the balancing of maintenance costs against fixed charges. In order to observe the relations among the various factors that affect the speed of combustion, representative particles of fuel will be followed through two types of furnaces. A pulverized-coal furnace will be considered first, because the independence of the individual particles facilitates the analysis of the effect of furnace conditions. The second example will be a grate-fired furnace in which ignition of the fuel takes place on the underfeed principle. This includes both underfeed and chain grate stokers, (8)† but does not include hand-fired furnaces and some overfeed stokers. The furnace will be considered to be large enough, the temperature high enough, and enough air provided, to burn the fuel completely, without, for the moment, specifying these quantities more completely. Furnaces Burning Pulverized Coal In a pulverized-coal furnace, the fuel particle is carried, in a stream of air, into the furnace, where it is subjected to radiation from the flame and from the hot walls of the furnace. The increase of particle tempera-

Jan 1, 1936

By Evert Hoek

SYNOPSIS It can be shown that the properties of intact rock are relatively unimportant in rock slope stability and that failures are controlled by structural discontinuities such as bedding planes, joints and faults in the rock mass. The frequency, orientation and inclination of these discontinuities as well as their strength characteristics are important factors to be considered in any rock slope analysis and their influence will be demonstrated by means of a number of practical examples. Methods for determining the mechanical properties of discontinuities will be reviewed and the interpretation of the strength test results for use in stability computations will be discussed.

Jan 1, 1971

By A. N. Crownover, H. T. Kennedy, E. P. Miesch, C. H. Bowman

The paper presents correlations of (l) molar volume of gaseous hydrocarbon mixtures with pressure, temperature, composition and properties of the C,-plus fraction; (2) shrinkage of oils during flash and differential liberation of gas, including the calculation of formation volume factor under various conditions; and (3) bubble-point pressure with temperature, composition and characteristics of C, plus. The data on which the correlations are based comprise 1,615 measurements on 900 hydrocarbon systems, including numerous systems containing nitrogen, hydrogen sul-fide and carbon dioxide. In each correlation, the number of data points covered and the accuracy is substantially greater than in previously available work. Thus, the equation yielding molar volumes of gases has an average deviation of 2.04 per cent, applied to mixtures having temperatures up to 313F and pressures up to 9,800 psis, compared to 2.37 per cent for the Benedict-Webb-Rubin equation applied to the same data, and 4.53 per cent for the method based on the law of corresponding states. he equations resented are all explicit in the dependent variable, and require no iteration on the digital cow puter. INTRODUCTION The ease and accuracy of determining the composition of hydrocarbon mixtures, compared to the difficulty of measuring their properties under reservoir conditions, makes it desirable to utilize composition as the key to physical behavior to the greatest possible extent. As a result, there are available correlations between composition, or easily measured characteristics dependent on composition, and practically every important engineering property of reservoir fluids. The task confronting us is one of finding more exact relationships between important variables rather than extending correlations to new properties. This paper describes new correlations of molar volumes of gases, formation volume factors, and bubble-point pressures with composition, temperature and where possible, pressure. Each correlation is obtained by employing a sufficiently large amount of data so the calculated properties are probably as least as accurate as the measurement on which they are based. MOLAR VOLUME OF GASES Although many equations of state have been proposed for pure gases, only a few methods are applicable to hydrocarbons at conditions comparable to those in petroleum reservoirs. Still fewer arc useful in describing the behavior of mixtures, with which the petroleum engineer is largely concerned. The correlation presented here involves procedures similar to those of Alani and Kennedy The van der Waals equation is modified to make a and b functions of temperature instead of being constants for each material.This is a cubic equation, which may have either one or three real roots. The lowest root corresponds to liquid volume, while the highest applies to gas. When the procedure was applied to 703 pressure-temperature points of 164 gases of known composition and volume, the average deviation was 12.08 per cent, and the standard deviation 8.15. The above calculations were made using the constants derived for liquids by Alani and Kennedy and the mixture equation developed by them. A closer approximation to measured molar volumes is obtained by employing different sets of constants for different areas on the pressure-temperature chart, and by changing the relationship between a,,, and b,,, for mixtures and the a, and b, for individual hydrocarbons. The various sets are shown in Table 1, and the areas for which they are recommended are plotted in Figs. 1 through 7. In these figures, the area designated by zero is in the critical region for pure materials, and the values obtained for them may be unreliable. For normal mixtures, however, the area may be added to any of the bounding areas without substantial error. The new relationships employed are

Jan 1, 1966

By J. B. Austin

MEASUREMENTS of the rate of decomposition of austenite at constant temperature are commonly represented by plotting the percentage trans-formed on linear coordinates against time on either a linear or a logarith-mic scale, a method that yields a curve that in shape resembles an integral sign (Fig. 1). A graph of this kind is not always convenient because extrapolation to the beginning or end of the transformation, or even inter-polation, may be uncertain unless there are a large number of observations, which seldom happens; furthermore, the degree of consistency of a set of measurements is difficult to judge from such a curve. It is desirable therefore to find some mode of plotting, or even better to find a standard variety of graph paper, that gives a straight line instead of the integral shape. The straight line has many advantages; the number of readings required to fix the position of the curve is greatly reduced, interpolation is easy and rapid, extrapolation can be carried out with greater confidence and, finally, the consistency of the measurements is readily estimated from the scatter of the points. The last advantage is particularly valu-able when the data are obtained by direct microscopic examination alone, because they are influenced by the skill of the observer in estimating the relative size of areas, possibly also by undetected inhomogeneity of the specimen. A search for ways of representing the observations as a straight line yielded two methods which are described in this paper. The paper also includes an account of some interesting relations brought to light in applying these methods to the available experimental data. Usually the best way to derive such a method of plotting is to base it on established principles of chemistry and physics, as has been done, for example, for the temperature variation of the equilibrium constant of a chemical reaction. But so little is known of the mechanism of the decom-position of austenite, and so little is available in the way of well established background for changes of this kind, that it is simpler to rely upon purely empirical means. The general plan therefore is to study existing data with a view to finding some function of the direct observations that will

Jan 1, 1938

By Aloys IL. Wollrab

The conditions that govern the selection of a suitable type of detachable bit for the small, isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may not be able to adopt the practice of large mines because of necessary capital expenditures for equipment for detachable-bit sharpening and . shanking. The perfect detachable bit, suitable for all conditions, has not yet been developed. Conventional Drill Bit in Use That drilling speed increases as the bit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests carried out by Holman Brothers Limited1 with 7/8-in. steel show that when bit sizes are reduced from I½ in., I3/8 in., and I3/16 in-; to I3/8 in., I1/4 in.., and I1/8 in., respectively, the volume of the hole is I 5 per cent less and the drilling speed 49 per cent higher. Recent tests by the United States Bureau of Mines2,3 in hard, uniform basalt showed that a reduction in average gauge from 2.077 to I,826 in., a difference of o.25I in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and 14° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr charac1erist.i~~) by some mines4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and 14° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as call be forged economically. Shop practices and costs have been discussed in earlier paper.5,6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert. Requiremnts for Detachable. Bit for Hollinger Under these it it was appar- ent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in

Jan 1, 1943

By Aloys IL. Wollrab

The conditions that govern the selection of a suitable type of detachable bit for the small, isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may not be able to adopt the practice of large mines because of necessary capital expenditures for equipment for detachable-bit sharpening and . shanking. The perfect detachable bit, suitable for all conditions, has not yet been developed. Conventional Drill Bit in Use That drilling speed increases as the bit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests carried out by Holman Brothers Limited1 with 7/8-in. steel show that when bit sizes are reduced from I½ in., I3/8 in., and I3/16 in-; to I3/8 in., I1/4 in.., and I1/8 in., respectively, the volume of the hole is I 5 per cent less and the drilling speed 49 per cent higher. Recent tests by the United States Bureau of Mines2,3 in hard, uniform basalt showed that a reduction in average gauge from 2.077 to I,826 in., a difference of o.25I in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and 14° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr charac1erist.i~~) by some mines4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and 14° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as call be forged economically. Shop practices and costs have been discussed in earlier paper.5,6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert. Requiremnts for Detachable. Bit for Hollinger Under these it it was appar- ent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in

Jan 1, 1943

By J. N. Anderson

Developments in reverberatory furnace practice at Noranda over the period 1928 to 1953 are described. Features of interest are increasing furnace tonnage from 700 to 2000 tons per furnace day, the use of the suspended basic roof, and improvements in furnace fuel ratio. Points of comparison and contrast between Canadian and American furnace practice are given. OPERATIONS at the Noranda smelter have been described in a series of papers published between 1930 and 1945.1-4 In the present paper the development of reverberatory furnace practice over the 25 year period from the beginning of operations up to the present time will be reviewed and current furnace practice will be described in some detail. Particular attention will be given to those features which are characteristic of Canadian practice: first, the use of the suspended basic roof; second, the deliberate driving of furnaces to give tonnages in the range of 1400 to 2000 tons of solid charge per furnace day; and third, the continuous operation of furnaces at high tonnage for many years without any extended shutdown for repairs or rebuilding. Finally, points of comparison and contrast between reverberatory furnace practice in Canada and the United States will be discussed. The Noranda smelter, which started in December 1927, was built for the reduction of ore from the Horne mine where early development had shown a comparatively small tonnage of rich cop-per-gold ore of a grade and character which would require direct smelting. The smelter was designed for a capacity of 1000 tons of ore a day and originally consisted of eight roasters, two reverberatory furnaces, and two converters, together with necessary auxiliaries. The discovery of a large new body of ore in 1928 made it necessary to increase both the size and the scope of the reduction plant. A mill which was ultimately brought to a capacity of 3000 tons a day was built for concentrating low grade ore and in addition the capacity of the smelting plant had to be greatly expanded, so that for the next fifteen years every effort in the smelter was directed toward achieving maximum tonnage. Because the layout and design of the smelter made it impracticable to add a third furnace, it was necessary to increase the tonnage on the two original furnaces by improvements in furnace design and operation, roasting and converting equipment being added as required to meet the demands of increased furnace capacity. The smelter tonnage, which reached a peak in 1941, was curtailed in 1944 when it became necessary to operate on a one-furnace basis because of a reduction in the output of the Horne mine due to a shortage of labor. Two-furnace operation at a moderate tonnage was resumed in 1949. In the early years the smelter tonnage was made up almost entirely of Noranda ores and concentrates. However, since 1937 an increasing tonnage of ores and concentrates from other mines has been treated in the smelter. In recent years, with decreased production from the Horne mine, copper concentrates from several mines in the district, treated on a custom basis, have formed an important part of the smelter tonnage. A review of developments in reverberatory furnace practice at Noranda falls naturally into the following four periods: 1—1928 to 1935, the early years; 2—1935 to 1944, the period of greatest change and development; 3—1944 to 1949, one-furnace op-

Jan 1, 1955

By R. S. Silo

A new process for leaching oxidized copper ore (CuO) is presented. Its principle advantage is that it requires low cost raw materials. For large operations the only materials used are sodium chloride (NaCl) and calcium carbonate (CaCO3). In those operations of medium size, sulfur, which is abundant in the North of Chile, is used. However the process may also be applied to small copper plants provided low cost sulfuric acid is available as a substitute for sulfur. That is, it may be applied to those small capacity plants where large additional installations for the regeneration of the leaching solution are not needed. The method is comprised of six stages, namely: Crushing, Leaching, Washing of the Solution, Precipitation, Regeneration of the Leaching Solution, and Fusion. A flow diagram for this process in a large or medium-sized plant is given. LEACHING This process requires hydrochloric acid as the leaching solution for treating copper ores. This is easily produced from sulfuric acid and sodium chloride as follows: A small excess of NaCl is advisable to avoid the presence of free sulfuric acid. The experiments reported here were performed with 36 grams of HC1 per liter of solution to obtain a free acidity equivalent to 50 gpl of H2SO4 (the usual leaching solution concentration). Hydrochloric acid leaching may be done by either of the usual methods; i.e. percolation or agitation. The method selected depends on the characteristics of the ore. No matter which method is chosen, low pressure air can be used either as an air lift for circulation of the solution, or for agitation of the pulp with "Pachuca" tanks. In either case, there are no problems with respect to oxidation. Leaching by agitation produces good recovery; but at times, the problem of high consumption of leaching solution or the overproduction of grinding slimes which interfere with contact between phases negates this advantage. The percolation method was used in this study. Percolation took place in four 15-liter containers, 11 1/2 in. diam. by 12 in. height, having hemispheric bottoms. Each container was fitted with a wooden bottom having 1/4 in- holes. The air lift was a 3/4 in. plastic tube 10 in. high. Air at 6 psi was supplied from a rotating laboratory compressor. 10 kg of ore were charged to the container and counter-current leaching was used. The leaching solutions were fed through the center pipe in order to use the ascending solutions to reject the air in the charge. The solution circulated through the air lift in order to facilitate the movement according to the increase in density produced by the reaction between the phases present. Specific observations made in this report cannot be generalized because the leaching characteristics are dependent on the nature of the ore used, the method of leaching, and the production of primary or secondary slimes while crushing or leaching.

Jan 1, 1967

By A. D. Rovig, D. W. McGlashan, Donald M. Podobnik

Crystal-chemical and stntctural properties of sulfide minerals are considered. The information gained is to be used to interpret (I ) freshly broken mineral surfaces, (2) modifications of the mineral surfaces, and (3) reactions at the mineral surfaces. From these basic disciplines, concepts with regard to the changes that surfaces undergo, reactions that might take place, the geometry of the interface, the state of different atoms and ions in the interface, and other physical and chemical properties of an interface must be developed, weighed and applied. The authors first deal with these conceptual considerations from which hypotheses are set forth to describe the environ men tal-interfacial relationships for several sulfide minerals. Qualitative and quantitative explanation of par-ticulate solid separations are unknown entities because of the lack of adequate models and mathematical relationships to explain the activity occurring between the solid and liquid phases. It is a transitional region in which it is difficult to ascertain the mechanisms of adsorption of ions, molecules, etc., on mineral surfaces, as well as other secondary reactions which occur in interfacial regions. Thus, in this paper the authors deal with conceptual considerations from which hypotheses are set forth to describe the environmental-interfacial relationships for sulfide minerals. GENERAL CONSIDERATIONS Interfacial Reactions:Interfacial reactions are the cruxes of flotation schemes as well as other processes such as thickening, filtration and hydrometallurgy. However, as noted by Klassen and Mokrousov: 1 "The problems concerning the surfaces of natural minerals, the laws governing simultaneous adsorption from aqueous solution on these surfaces of a whole series of reagents, the laws of the surface reactions and the properties of water layers separating the minerals, are all known to a first approximation only." An investigator has the privilege of postulating methods of solid-liquid interfacial reactions. REACTIONS WITH WATER - Water consists of hydronium (H3 O 4) and hydroxyl (OH-) ions in the ionized state. That this is so forms the basis for the postulated reaction of the hydrated hydrogen ion with net-negative mineral surfaces as depicted in Fig. 1. In this case water is bonded to mineral surfaces through hydrogen-bridge-type bonds - possibly hydrogen bonds. Although bonding of the van der Waal type may be responsible for this reaction, it is most likely that stronger bonds are involved. Once firmly bonded to the surface, the water layer is known to be quite tenacious. It is further speculated that a shear plane exists at some distance (see Fig. 1) away from the mineral surface. Exact location of this plane is not known, but in all probability it will be positioned across a weak bond of the hydrogen-bond type where the surface-attached water is coordinated to the original hydrated hydrogen ion. REACTION WITH METAL IONS - Klassen and Mokrousov ' state: "The presence of an ion in water leads to an immediate formation around that ion of a highly condensed atmosphere of water dipoles and thus to hydration of the ion." The fact is known that multivalent cations are strongly hydrated, usually by six or eight molecules of water, and that anions are not so strongly hydrated. Conceding the fact that thermodynamics, concentration, pH, and physical considerations are of utmost importance in truly explaining a mechanism of metal ions reaction with a hydrated mineral surface, it does seem logical that the mechanism illustrated in Fig. 2 is feasible. In this reaction, the metal ion (M) is coordinated in one dimension - to the mineral-surface hydration layer. Note also that explanation of this reaction requires that the shear plane move to a less stable bond configuration; that is, the shear plane has moved to a position between the metal ion and the other coordinated water molecules which are more free to dissociate. Reactions as depicted in Fig. 2 should cause the formation of an apparent mineral surface which is net-positive. Immediately, it must be noted that measurements of apparent-mineral surfaces serve - within limits - to indicate a degree of ion-surface reaction capability. The major limiting factor he re is one related

Jan 1, 1970

By C. Richard Tinsley

SUMMARY A detailed analysis of nickel, copper, and cobalt recovery from manganese nodules shows simple rates of return of 9-15% in 1985. A sulfur dioxide roast process yields a slightly better return than an ammonia leach technique. Nodule tonnage predictions tend to be over-optimistic and more conservative forecasts show that market penetrations are only significant for cobalt and manganese. However, cobalt prices are unlikely to fall to the level of nickel. Between now and 1985, cobalt is expected to be in balanced to tight availability. INTRODUCTION Deep-ocean manganese nodules are one- to two-inch concretions which cover 2040% of large areas of the ocean bottom. Commercial targets far these black, potato-like nodules are located in the North Pacific at water depths of 5,000-6,000 m. in a belt roughly midway between Hawaii and Mexico. However, good grade nodules are not solely limited to this belt as areas southwest and northwest of Hawaii, as well as in the Indian Ocean, contain concentrations of acceptable grade manganese nodules. Some 90% of the nodules are found half-buried on the deep ocean bottom. A siliceous-ooze host soil combined with low sedimentation rates, certain ocean currents, and possible geo- thermal effects are favorable factors far nodule formation. The viewpoints and analyses in this paper are the author's own and should not be attributed in any way to Amoco Minerals Co.

Jan 1, 1976