Search Documents

By W. L. Saunders

This paper deals specifically with heading-driving as distinguished from the broader term tunnel-driving. A heading is a pilot or path-finder for the main tunnel. Some headings are complete tunnels in themselves; that is, conditions at times warrant driving a heading the full diameter of the proposed tunnel. A tunnel 10 ft. in diameter might be driven to advantage through a single heading, provided the nature of the material admits, but it usually pays to drive rock tunnels of large diameter through the heading-and-bench system. Much depends upon the material, as in soft ground tunnels of much larger diameter are driven in a single heading. In mines, the tunnels, drifts, cross-cuts, adits, etc., are usually of small diameter, hence the driving of headings applies to completed tunnels in mining-work, except, of course, in cases like drainage-tunnels and main entries leading into coal-mines, where conditions call for tunnels of large diameter, approximating those driven for railway-service. In building aqueducts the tunnels are driven from 6 to 8 ft. in diameter up to 15 or 20 ft., while in railway-service the dimensions vary from 18 to 30 ft. in diameter. There is no department of rock-excavation so difficult as that of heading-driving. This work also belongs to the most expensive class in rock-excavation. A heading is driven directly in the solid. There are no lines of lesser resistance towards which to direct the energy of the blast, but the material must be blown out by main force. The completion of the heading simplifies all the rest of the work of excavation. It is easy, for instance, to enlarge a heading either from above, below or on the sides, by breaking towards the open face through holes approximately at right angles to the axis of the heading; or the enlargement sometimes takes place by holes driven outside of the heading running approximately parallel with it, the rock

Jan 1, 1910

By T. Sterry Hunt

The deposit of rock-salt which is known to exist along the eastern shore of Lake Huron, in the province of Ontario, has lately been more completely explored than before, by a boring with a diamond drill, put down by Henry Attrill, Esq., of New York City, and the results obtained are so important in every way that I make no apology for presenting them to the Institute of Mining Engineers. I may be permitted to preface an account of this remarkable exploration, and of its results, with a historical sketch of the discovery and development of this salt-region. It was in December, 1865, that a boring was begun near the town of Goderich, in the hope of finding petroleum. In this the adventurers were disappointed, but, after passing through about 800 feet of limestone, they encountered a series of variegated marls, in which, at a, depth of 964 feet from the surface, a bed of rock-salt, 30 feet in thickness, was met with in May, 1866. The boring was carried to a depth of 1010 feet, ending in hard rock, and yielded, by pumping, a very pure saturated brine when examined by me in August of the same year. In the report of the Geological Survey of Canada for 1863-66, published early in 1867, I described this salt-well, with many geological details, and gave an analysis of the brine. In the next three years a considerable number of wells was sunk in and around Goderich, and numerous trials were made in various other parts of the region. Salt was found at Kincardine, thirty miles north-northeast from Goderich, at a depth of about 900 feet, and also at Clinton, thirteen miles southeast, at 1180 feet. Records of these wells, with analyses of the brine from them, were given by myself in a subsequent report of the Geological Survey, 1866-69, published in 1870 (pp. 211-244), together with accounts of various unsuccessful borings in the neighborhood, analyses of the brines from the various wells (including one analysis by Dr. Goessmann), with many details of the salt-manufacture at Goderich, at Syracuse, New York, and at Saginaw, Michigan. The geological character of the region was there discussed at length, and it was shown that the salt here occurs in the Onondaga or Salina formation, which

By T. Sterry Hunt

THE deposit of rock-salt which is known to exist along the eastern shore of Lake Huron, in the province of Ontario, has lately been more completely explored than before, by a boring with a diamond drill, put down by Henry Attrill, Esq., of New York City, and the results obtained are so important in every way that I make no apology for presenting them to the Institute of Mining Engineers. I may be permitted to preface an account of this remarkable exploration, and of its results, with a historical sketch of the discovery and development of this salt-region. It was in December, 1865, that a boring was begun near the town of Goderich, in the hope of finding petroleum. In this the adventurers were disappointed, but, after passing through about 800 feet of limestone, they encountered a series of variegated marls, in which, at a, depth of 964 feet from the surface, a bed of rock-salt, 30 feet in thickness, was met with in May, 1866. The boring was carried to a depth of 1010 feet, ending in hard rock, and yielded, by pumping, a very pure saturated brine when examined by me in August of the same year. In the report of the Geological Survey of Canada for 1863-66, published early in 1867, I described this salt-well, with many geological details, and gave an analysis of the brine. In the next three years a considerable number of wells was sunk in and around Goderich, and numerous trials were made in various other parts of the region. Salt was found at Kincardine, thirty miles north-northeast from Goderich, at a depth of about 900 feet, and also at Clinton, thirteen miles southeast, at 1180 feet. Records of these wells, with analyses of the brine from them, were given by myself in a subsequent report of the Geological Survey, 1866-69, published in 1870 (pp. 211-244), together with accounts of various unsuccessful borings in the neighborhood, analyses of the brines from the various wells (including one analysis by Dr. Goessmann), with many details of the salt-manufacture at Goderich, at Syracuse, New York, and at Saginaw, Michigan. The geological character of the region was there discussed at length, and it was shown that the salt here occurs in the Onondaga or Salina formation, which

Jan 1, 1877

By D. K. Crampton, H. I. Burghoff, J. T. Stacy

The effect of cold-working upon electrical conductivity of copper and of copper alloys appears not to be generally known in detail. Although several papers on the subject have been presented, showing variable effects according to alloy composition, it is often assumed that the 2 to 3 per cent lowering of the conductivity of ordinary tough-pitch copper by severe cold-working is typical for copper alloys. Because of this situation it was decided to carry out the present work upon several types of copper, copper-zinc alloys over the commercial range of brasses, other binary alloys, and numerous age-hardening alloys in the quenched, and quenched and aged conditions. The large number of alloys investigated made it impossible to study every one in the detail it may have merited. Inasmuch as several interesting points that could not be satisfactorily explained came to light, further work is contemplated by the authors. It is usually considered that the normal effect of cold-work on ductile metals and unordered alloys is to decrease conductivity slightly. In alloys that are in the ordered state, as annealed or otherwise heat-treated, cold--working tends to disorder the structure, resulting in very marked lowering of conductivity. The random state of atomic arrangement produces lower con- ductivity than the ordered state for the same composition.1 Previous Work Previous work in the authors' laboratory has shown the electrical conductivity of several copper alloys to be decreased by greater amounts than might have been expected, in view of the general knowledge on the subject, when cold-worked. Guillet and Ballay2 investigated the influence of cold-work upon the resistivity of several metals and alloys, including copper and some copper alloys. The increase of resistivity due to severe working w is less than 4 per cent for all pure metals tested, while the increases for the alloys were generally higher. In the copper-zinc alloys, they found that the increase of resistance due to drawing increased with zinc content, and reported a 21.7 per cent increase of resistance for an alloy contaiiiing 67.9 per cent Cu as severely worked. Masima and Sachs3 studied the change in electrical resistance of three brass crystals when stretched in the tensile test, obtaining increases in resistance of the order of 3 per cent for 30 to 40 per cent reduction of area of the specimens. The resistance decreased again when the cold-worked crystals were subsequently annealed. Bardenheuer and Schmidt4 found that the conductivity of copper was decreased by 3 to 4 per cent when reduced 50 per cent by working. The conductivity of 72-28

Jan 1, 1941

By R. E. Zimmerman, T. W. Guy

IN approaching the problems of sampling coal, a brief statement of certain facts that are more or less taken for granted may be helpful: 1. The coal-mine operator needs reliable data as to the physical and chemical characteristics of his coal in order to plan and control intelligently its mining, preparation, and marketing. The consumer needs such data in order to select the equipment and the coal best suited to meet his requirements, to check the quality of fuel delivered, and the efficiency of its use. Various government control agencies require such data as a basis for classifications and establishment of limits, for use in carrying out the requirements of federal, state or municipal laws. 2. All such data must be obtained by analyses, measurements, or tests made on samples, which are taken to represent the coal tested. It is now becoming generally recognized that, in accordance with statistical laws, test results from samples are not expected to represent the exact qualities of the lot or lots from which they are taken, except within statistical, or "expected" limits. Such limits are definitely specified by some present standards of the American Society for Testing Materials and the British Standards Institution. 3. Samples that give ash within satisfactory limits are usually assumed to be sufficiently accurate for other analyses, except under special conditions such as meeting close specifications for coals showing wide variability in sulphur, fusibility of ash, or other quality. 4. In modern coal sampling the increment is recognized as the basis for taking samples. For a given accuracy the number and weight of increments specified are increased with: (a) the expected ash, and (b) the top size designation of the lot to be sampled. 5. It is extremely important that every sampler recognize that: the specified number and weight of increments are minimums, and that the precautions to be used in order to take them properly are also minimums; that in the reduction of the gross sample the sizes specified for the coal after each stage of the crushing are maximum; that the quantities specified to be taken after each crushing stage are minimum; that any short cuts or failures to meet the requirements specified will reduce the statistical accuracy of the results, although it is possible that one or two checks on a few results may seem to show otherwise.

Jan 1, 1950

By George K. Foster, Charles D. Borror

THE Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest openpit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. THE ORE BODY The ore body is a serpentinized peridotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur perpendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber [ ]

Jan 1, 1946

By Murray Kaufman

Using en; 41 for a base alloy, 15 modifications were made in sheet form. The elements Al, Ti, C, Mo, Co, and Cb were varied. The effects on the phases formed and their temperature dependence, the aging characteristics, tensile and stress-rup- ture properties, and weld cracking were determined. The A1-Ti content and balance is the most important factor influencing the major sCrengthening phases [Ni,Ti and Ni,(Al, Ti)] and, consequently, mechanical properties. THE mechanical properties, fabricating and joining characteristics, dimensional stability, and so forth, of alloys containing secondary phases are largely determined by the phases present, their distribution, and their temperature dependence. The phases in the basic ternary and quaternary Ni-Cr-Al-Ti combina- tions have been investigated thoroughly.'* The phase behavior of many commercial nickel-base alloys has been determined also. In some cases, for example U500, 5 the effect on mechanical properties has been found. However, little systematic work has been done to clarify the action of each of the important alloying elements in controlling the phases formed in complex commercial alloys and their behavior. The effect of molybdenum on the carbides formed in M252 was investigated by Beattie and verSnyder.6 Application of the results provided by that work

Jan 1, 1963

By Edward Saibel

The various theories that have been advanced to explain or predict the conditions under which a metal fractures may be divided into two categories: First, there are the macroscopic theories generally used in engineering practice. These are empirical in nature and limited in application. For example, the maximum normal stress criterion, which is quite satisfactory for a mild steel in simple tension at atmospheric pressure,' no longer suffices when this steel is pulled under hydrostatic pressure.2 In all of these empirical theories, the critical condition characteristic of the material and of the loading conditions must be obtained experimentally. Secondly, there are the theories based on interatomic forces,3'4 or on the energy required to form new surfaces.5,6 These have all dealt with the theoretical evaluation of the tensile stress necessary to bring about rupture in a purely brittle manner; that is, without plastic flow preceding fracture. All of these attempts have led to values of the tensile strength of crystals or of polycrystalline bodies that are 100 to 1000 times higher than observed values. On this account, it has been thought necessary by some investigators to conceive of a microcrack structure or distribution of flaws throughout the specimen such that the resulting stress concentrations provide the factor necessary to bring about agree- ment between calculation and experiment. It has been pointed out by several observers' that this point of view is highly unrealistic, in that the weakening effect of these flaws or microstructures must be very uniform from specimen to specimen, since the fracture stresses found for various specimens of the same material tested under similar conditions are so nearly constant. Furthermore, since calculations based on atomic forces or atomic energy are for purely brittle fracture, a condition probably never satisfied in tests, agreement is hardly to be expected. Thermodynamic Theory of Fürth In order to resolve this apparent discrepancy between the theoretical cohesive strengths and the observed fracture strengths, Fürth8 advanced a thermodynamic theory of the tensile strength of isotropic bodies based on work of Born relating to the melting of crystals. Assuming an isotropic material free from imperfections and flaws, behaving elastically up to the breaking point, and assuming a connection between rupture and the melting phenomenon, Fürth obtains an expression for the rupture stress a, in the form where Q is the melting energy per unit mass, p is the density, and is Poisson's ratio. Furth compares fracture stresses computed from Eq I with the fracture stresses of metals as given in the Landolt-Bernstein Tables (1927) and in the Hand-

Jan 1, 1947

By Edward Saibel

The various theories that have been advanced to explain or predict the conditions under which a metal fractures may be divided into two categories: First, there are the macroscopic theories generally used in engineering practice. These are empirical in nature and limited in application. For example, the maximum normal stress criterion, which is quite satisfactory for a mild steel in simple tension at atmospheric pressure,' no longer suffices when this steel is pulled under hydrostatic pressure.2 In all of these empirical theories, the critical condition characteristic of the material and of the loading conditions must be obtained experimentally. Secondly, there are the theories based on interatomic forces,3'4 or on the energy required to form new surfaces.5,6 These have all dealt with the theoretical evaluation of the tensile stress necessary to bring about rupture in a purely brittle manner; that is, without plastic flow preceding fracture. All of these attempts have led to values of the tensile strength of crystals or of polycrystalline bodies that are 100 to 1000 times higher than observed values. On this account, it has been thought necessary by some investigators to conceive of a microcrack structure or distribution of flaws throughout the specimen such that the resulting stress concentrations provide the factor necessary to bring about agree- ment between calculation and experiment. It has been pointed out by several observers' that this point of view is highly unrealistic, in that the weakening effect of these flaws or microstructures must be very uniform from specimen to specimen, since the fracture stresses found for various specimens of the same material tested under similar conditions are so nearly constant. Furthermore, since calculations based on atomic forces or atomic energy are for purely brittle fracture, a condition probably never satisfied in tests, agreement is hardly to be expected. Thermodynamic Theory of Fürth In order to resolve this apparent discrepancy between the theoretical cohesive strengths and the observed fracture strengths, Fürth8 advanced a thermodynamic theory of the tensile strength of isotropic bodies based on work of Born relating to the melting of crystals. Assuming an isotropic material free from imperfections and flaws, behaving elastically up to the breaking point, and assuming a connection between rupture and the melting phenomenon, Fürth obtains an expression for the rupture stress a, in the form where Q is the melting energy per unit mass, p is the density, and is Poisson's ratio. Furth compares fracture stresses computed from Eq I with the fracture stresses of metals as given in the Landolt-Bernstein Tables (1927) and in the Hand-

Jan 1, 1947

By T. V. Falkie, D. R. Mitchell

Many operational problems in mine haulage cannot be solved economically by conventional analytic or trial and error methods. However, a method of probabilistic simulation, which is based on the fundamental assumption that many of the variables governing any physical system are probabilistic, has been adapted to certain areas of operations research in coal mine haulage. This paper attempts to illustrate how simulation can be used in basic haulage research and what kind of results can be expected. Optimization in this case is performed in terms of locomotive and car movement, as well as best utilization of men and equipment, and is approached primarily from the standpoint of scheduling of the main haulage. Many operational problems in mine haulage cannot be solved economically by conventional analytic or trial-error methods. However, a method of probabilistic simulation, which is based on the fundamental assumption that many of the variables governing any physical system are probabilistic, has been adapted to certain areas of operations research in mine haulage. In many physical cases several probability distributions interact with each other in special ways, and it is not possible to solve for their combined effect in a mathematical equation. This is often true in the case of mine haulage, where such variables as number of empties or loads per trip, travel times, and number of cars or tons produced in a given time are probabilistic. By using a simple example of one secondary haulage segment of a large underground haulage system, this paper attempts to illustrate how simulation can be used in basic haulage research and what kind of results can be expected. Optimization in this case is performed in terms of locomotive and car movement, as well as best utilization of men and equipment. This is the type of preliminary research that will be needed as a first phase in any major haulage study, whether it be a relatively simple economic analysis or a plan for complete automation. The problem of optimization has been approached primarily from the standpoint of scheduling of the main haulage. It is evident that the method of proba-

Jan 1, 1963

By J. Spotts McDowell

Preparation and Use.-Magnesite is an important refractory in open-hearth, heating, and electric furnaces for steel-making and in many of those employed in the metallurgy of copper and lead. It is sold in the form of brick, finely ground "furnace magnesite" for brick-laying, and dead-burned grains for making and repairing furnace bottoms. The latter are a mixture of granules varying in size from pieces of about 5/8 in. (1.6 cm.) diameter to very fine but sandy particles. Dead-burned magnesite results from calcining 'the crude or lightly burned mineral at a temperature that will not merely drive off practically all the CO2, but will also cause sintering of the particles. During this process the pieces shrink considerably and become hard, dense, and inert to atmospheric moisture and C02; under-burned material, on the other hand, will hydrate on exposure to the air. A small percentage of ferric oxide seems to be necessary for the production of a satisfactory sinter; from 4.5 to 8 per cent. in the dead-burned grains is considered the most desirable amount. Dolomite has been little used for brick-making in the United States, but it is prepared for use in the granular condition calcined or "double-burned" and is the principal ingredient of several materials offered for sale under various trade names for refractory purposes. Dolomitic refractories are almost wholly confined to the open-hearth and electric furnaces, where they are used for fettling and as substitutes for magnesite. Much more magnesite and dolomite are used for basic open-hearth steel-making than for all other refractory purposes. The hearth of the furnace is usually built up of magnesite brick and dead-burned grain magnesite so laid that the brick base is protected by a working bottom of the granular material. The latter is sintered into place in layers 1 to 2 in. (2.5 to 5 cm.) thick to a total depth of 12 to 18 in. (30 to 45 cm.) at the center of the furnace. After each heat, burned dolomite is thrown against the banks as high as it will stick, and all holes in the bottom are filled. At most plants such holes, at the end of each week, are also

Jan 2, 1919

By W. S. Burbank, B. S. Butler

STUDY of the ore deposits of Colorado has disclosed, in numerous places, sharp changes in both mineralogy and metal content of the primary or hypogene deposits with change in depth. A clear understanding of the meaning of these changes is requisite to form intelligent conclusions that can be applied in the exploration of such ore deposits. This paper is an attempt to set forth some of the geologic and chemical relations of minerals that bear on this problem. The effect of the differing electrode potentials of elements on the order of oxidation and on the order of displacement of one metal by another metal in supergene sulfide deposits has been studied for many years by several investigators. The results all agree rather closely with the original Shurmann series of replaceability of metal sulfides, as Wells has shown.1 So far as the writers are aware there has been little attempt from the geologist's viewpoint to correlate the electrode potentials of the elements, other than those of the common metals, with the positions and mode of combination of the elements as found in ore deposits, and in particular in hypogene deposits. Wells2 discusses electrochemical activity between solutions and certain ore minerals and mentions the possibility of its effect in precipitation reactions. The senior writer for a number of years has emphasized the importance of oxidation-reduction reactions as a factor in the formation of certain hypogene ore minerals, and as the electrode potentials are a measure of the relative Oxidizing and reducing power of the elements and their ions, it seems possible that a study of them may offer some suggestions on certain problems. The data at present available for such a line of

Jan 1, 1929

By Frank Van Horn

IT is customary to ascribe two general modes of occurrence to natural gas, namely shale. gas which, as the name indicates, is found in' shale, and reservoir gas, which occurs ill sandstone, conglomerate and dolomitic limestone. Both of these types are found in the Cleveland district. The shale gas has been produced on a small scale for a long period of years, probably dating back as far as 1883. Shale gas is a low-pressure gas, small in volume with variable pressure, and is limited to no definite horizon. It is generally independent of oil, may last for a long time, and is not dependent to any great extent on the structure of the rocks. There are many such wells in the district which range from 400 to 1,840 ft. in depth, although most have been completed at about 800 ft. This indicates that the wells pass through the Cleveland and Chagrin shales into the Huron or Portage shale of the Upper Devonian. During the last 2 years great interest has developed in a deeper-seated reservoir gas. What is commonly called reservoir gas is generally a high-pressure gas occurring in large volume at a definite horizon. Oil may, or may not, be associated with the gas, and in most regions in which reservoir gas is found, the geological structure is of great importance. This type of gas occurs in all large fields such as those of West Virginia which have been supplying Cleveland until the recent discovery of local gas at great depths in commercial amounts.

Jan 1, 1917

By Stanley Herold

Considerable interest has been shown, during recent years, in the possibilities of developing oil fields in the South American Republics, now that the exhaustion of our present fields can be seen in the not very distant future. The demand for fuel oil and its products has been increasing far more rapidly than our increment of production during the last few years. Increase of consumption has been largely curtailed by the lack of sufficient supply. The main factors that have contributed to our previous neglect of the southern fields have been as follows:, (a) Lack of sufficient demand for the product. (b) Competition with producing fields, having large production, low cost, and better geographical position, such as Tampico, Mexico. (c) Greater interest in home fields with ready market at hand. (d) Our ignorance of southern economic and geologic conditions, clue to the distance between those areas and our financial centers. (e) Economic conditions in the southern countries, necessitating high costs of exploration and exploitation of the fields.

Jan 9, 1918

By Carl Henrich

Jan 1, 1890

By Howard Eavenson

EARLY in 1917, the United States Coal & Coke Co. secured options on several tracts in Harlan County, Ky., aggregating about 1.9,000 acres in area, and after careful prospecting by outcrop openings and diamond drilling, completed the purchase late in July of that year. This property is situated in the eastern end of Harlan County, south of the Poor Fork f Cumberland River, and extending across Big Black Mountain to the Clover Fork of Cumberland River, a distance of about 7 mi. (11.3 kg.). It extends from the Kentucky-Virginia line westward for about 6 mi. Looney Creek, which empties into Poor Fork, crosses the property for about 4 mi. (6.4 kg.), and as several of the seams within the property outcrop along this stream, it afforded an easy, and the logical, place for development. The property is on the northern side of the geological trough formed by the uplifting of Stone Mountain, on the southern, and Pine Mountain, on the northern side; the northern boundary along Poor Fork is practically at the base of Pine Mountain. This, area has been described in various geological reports.1 The main seam on this property is the one known variously as the "C," Benham, Keokee, Taggart, and Roda; it is, also called, by the Kentucky Geological Survey, the Kellioka seam of the western portion of Harlan County. This seam averages, in this property, about 5 ft. (1.5 m.) in thickness, although local rolls reduce this thickness considerably over small areas; and at the extreme western end of the property the seam splits. It is usually clean, although occasionally a small parting occurs within a few inches f the bottom f the seam; it is one f the best

Jan 9, 1921

By P. F. Gnirk, J. B. Cheatham

The results of combined analytical and experimental studies involving simulated multiple bit-tooth penetration into mck are incorporated into a drilling rate equation for roller-cone bits assuming rather idealized downhole conditions. In particular, it is assumed that the rock behaves statically in a ductile fashion during bit-tooth penetration and that the rock chips are instantaneously removed from the bottom of the drill hole. The general analysis demonstrates an application of plasticity theory for the rock/bit-tooth interaction to the formulation of an upper limit on rotary drilling rate. INTRODUCTION Extensive experimentation involving single and indexed bit-tooth penetration into rock in a confining pressure environment has demonstrated that the chip formation process is of a ductile, or pseudoplastic, nature at sufficiently low differential pressures so as to be of interest in rotary drilling. Coincident with the experimentation, analytical consideration has been given to the theoretical problems of single and indexed bit-tooth penetration into rock. In general, the analyses have assumed that the rock behaves statically in a rigid-plastic fashion and obeys the Mohr-Coulomb yield criterion. The quantitative comparison between experimental and calculated values of bit-tooth load required for chip formation has been remarkably good for a variety of rocks commonly encountered in drilling and at simulated differential pressures as low as 500 to 1,000 psi. Results obtained recently for indexed bit-tooth penetration indicate that the work (or energy) required to produce a unit volume of rock chip can be minimized by a proper combination of bit-tooth spacing and bit-tooth load for a given rock type and differential pressure. By utilizing this information, it is possible to formulate a drilling rate equation, at least in a preliminary fashion, for a roller-cone bit performing under rather idealized downhole conditions. In particular, through the use of characteristic dimensionless quantities pertinent to a roller-cone bit and to indexed bit-tooth penetration, interrelationships among bit weight, rotary speed, rotary power, bit diameter, rock strength and bit-tooth shape and spacing can be explicitly expressed. In the formulation of the equations, however, it is assumed that the rock chips are instantaneously removed from the bottom of the drill hole and- that the rock behaves in a ductile manner during bit-tooth penetration. In addition, the effects of bit-tooth load application and penetration by a yawed tooth at an oblique angle are neglected. Although the analysis is presented in the light of some rather restrictive conditions, it does demonstrate a method of applying fundamental rock/bit-tooth interaction data, obtained by combining the results of analysis and experiment to the formulation of a drilling rate equation for rotary drilling. JNDEXED BIT-TOOTH/ROCK INTERACTION PREVIOUS RESULTS The mechanics of bit-tooth/rock interaction under simulated conditions of borehole environment have been extensively described in a number of papers.l-ll In particular, the effects of differential pressure, mechanical properties of rock, pore fluid, bit-tooth shape and spacing, rate of bit-tooth load application and dynamic filtration below the bit-tooth have been investigated experimentally. From a sequence of experiments.1-4 it was demonstrated that, for dry rock at atmospheric pore pressure, the mode of chip formation exhibits a transition, with increasing confining pressure, from predominantly brittle to predominantly ductile. This transition

Jan 1, 1970

By Wm. Reuben Webster

Brass is an alloy of copper and zinc. The brass containing 70 per cent copper and brasses (using this term to denote all useful 30 per cent zinc. Fig. 3 shows the effect of proportions of the two constituents) are the annealing at various temperatures on the most valuable and widely employed of all same alloy. This effect is somewhat modi- nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure fied by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity —the hot hammer test. Samples 1/2 in. in diameter and 3/4 in. long are placed in a suitable furnace. These are withdrawn one at a time. at successively higher temperatures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of reduction in length of the cylinders are plotted against temperatures and give a camparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By Wm. Reuben Webster

Brass is an alloy of copper and zinc. The brass containing 70 per cent copper and brasses (using this term to denote all useful 30 per cent zinc. Fig. 3 shows the effect of proportions of the two constituents) are the annealing at various temperatures on the most valuable and widely employed of all same alloy. This effect is somewhat modi- nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure fied by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity —the hot hammer test. Samples 1/2 in. in diameter and 3/4 in. long are placed in a suitable furnace. These are withdrawn one at a time. at successively higher temperatures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of reduction in length of the cylinders are plotted against temperatures and give a camparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By Arthur S. Dwight

From the latest and best literature on lead-smelting, little can be learned concerning the present state of the art of mechanical feeding in the United States. H. O. Hofman, in his Metallurgy of Lead (5th ed., 1899), briefly describes the main features of the system in use at Pueblo, Colo., and later (p. 235) says " the only successful mechanical feeding, as far as the writer is aware, is that found at the works of the Pueblo Smelting and Refining Co." H. F. Collins, in his Metallurgy of Lead and Silver (London, 1899), covers American practice pretty thoroughly; but as to mechanical charging, he says: "The German plan of taking off the gases by means of a small iron pipe suspended in the center, and the plan of charging by means of cup and cone, as in iron blast-furnaces, have both been tried, but have not found favor, chiefly on account of the difficulty of obtaining free access to the furnace-shaft for barring, etc., with such devices."' . H. W. Hixon, in his Notes on Lead and Copper Smelting (3d ed., New York, 1900), gives a description and drawing of the Hixon feeding device, as originally installed at East Helena. Evidence that this system of feeding has passed its experimental stage, and deserves more serious consideration than it has heretofore received, is furnished by two large plants—the Pueblo and the East Helena—of the American Smelting and Refining Co., where mechanical feeding has been in continuous and successful operation for a considerable period; one new plant now erecting at Salt Lake City, Utah, and one old one belonging to the same company, the El Paso works, now being rebuilt after a disastrous fire, in both of which mechanical feeding is to be a prominent feature ; one new plant of an independent concern at Torreon, Mexico, which will adopt mechanical feeding; and a number of other smaller plants, among

Jan 1, 1902