Search Documents

By R. R. Goddard

By use of the frequency response method with a radioactive tracer, it was possible to determine fluid dispersion and distribution in a natural consolidated and an unconsolidated medium. Measurements were made in a linear flow system at oleic saturations of 69 per cent in the consolidated medium, and 100 per cent in both media. Dispersion and distribution were obtained by measuring the amplitude attenuation and the phase velocity of sinusoidal waves with a dual monitor apparatus. The gamma ray emissions permitted in situ measurements at any distance along the porous samples. One result of importance was that the effective diffusivity increased as the wave length increased. As a consequence, a dispersion coefficient appropriate for the injection of large slugs might exceed the value measured by use of small slugs. Since flow models based solely on fluid velocity and an effective diffusivity coefficient imply that the diffusivity should be independent of frequency, such representations were not adequate for the data of this study. A comparison was made with a capacitance model of porous media with deadend PVs, but even this model was not completely adequate. By using attenuation and phase velocity data, fluid dispersion can be predicted without postulating a differential equation satisfied by the tracer concentration, thereby eliminating the need of a complicated model to represent dispersion. INTRODUCTION The flow of similar miscible fluids through a porous medium can be fairly adequately described by two parameters: the average fluid velocity and the effective diffusivity.1-3 It has been pointed out recently, however, that significant discrepancies exist between this representation and the experimental data.4-7 An improved agreement can be obtained by introducing additional parameters based on the concept of dead-end pores. The purpose of the present investigation was to find out whether the frequency response method could be used to measure the relevant parameters. The method was used in the following form. A stream of fluid was flowed at a constant rate through a sample of porous material and the concentration of a radioactive tracer in the fluid was varied sinusoidally at a fixed frequency. The effects of flow through a porous medium are a decrease in the amplitude of the concentration wave and an increase in the velocity of the peaks of the waves above the average velocity. Attenuation and phase veIocity of the waves were measured as a function of frequency and fluid velocity. The simple two-parameter model implies that the diffusivity should be independent of frequency. Data reported in this paper show that the diffusivity decreases as the frequency increases. Hence, as shown also by many others, the two-parameter model is not completely adequate. Coats and Smith 5 used two additional parameters in their model: the volume of the dead-end pores and the rate of mass transfer between dead-end pores and the flowing stream. Their capacitance model of a porous medium containing some stagnant fluid, to which transfer occurs by molecular diffusion, did not explain the dispersion results of either the present study or of theirs. Instead, the capacitance effect can be better described as the result of extreme velocity variations within the pores of the medium, with transfer between the velocity zones by convection. EXPERIMENTAL PREPARATION OF POROUS MEDIA Data reported here were obtained with a natural Berea sandstone, and with two packings of 20/25 mesh sand. Pertinent information about these media is listed in Table 1. The sandstone core was first sealed with a non-

Jan 1, 1967

By J. R. Long, E. T. Hayes, R. S. Dean, F. S. Wartman

THE production of titanium in 15-1b. lots and with a purity sufficient to be consolidated into ductile metal, as described in a previous paper,1 has provided adequate material for a study of the : physical properties of titanium and a more thorough examination of its working qualities. Data on the physical properties reported in that paper were obtained on metal fabricated by a fixed procedure, standardized for the purpose of control of the reduction, and are representative only of material fabricated under those conditions. There are many possible variables in the working schedule, which will have significant effects on the properties of the finished material; and since the previous working methods were not necessarily the best, an investigation of the fabrication of titanium by other methods was undertaken. In this work the consolidation of the powder by pressing and sintering was conducted essentially as outlined in the report cited' and all efforts were centered on fabrication methods for those powders and the properties produced by them. Hardness, density, microstructure, and tensile properties were determined at various stages in the working and annealing; and resistivity measurements were made on a few bars and drawn wire. [ ] CONSOLIDATION OF THE POWDER The screen analysis of the available titanium powder is given in Table I. No attempt was made to alter the size distribution from that noted because this powder, although coarse by normal powder-metallurgy standards, produced acceptable compacts suitable for the present work. Because of their large specific surface, finer powders are more contaminated by oxygen and produce harder compacts, which are difficult to work. The powder as produced is soft, compresses in a normal fashion, and exhibits very little tendency to adhere to the die surfaces. Unlike aluminum and magnesium powders, it can be readily pressed without the use of die lubricants. When compacted at so tons per

Jan 1, 1946

By G. B. Walker, S. A. Falconer, S. J. Swainson, H. H. Vogel

During the past few years much interest and attention has been focused on a relatively new method of ore concentration, which utilizes the principles of sink and float and employs as the heavy medium a suspension in water of a finely ground solid, such as galena or ferrosilicon. Although a relatively recent development, much progress has already been made in applying heavy-media separation processes to a considerable number of ores. Eight plants in this country and abroad are now treating approximately 10 million tons of ore annually by heavy-media separation (sink-float) processes, including lead-zinc, lead, iron, garnet, tin and tungsten. At the annual meeting of the A.I.M.E. in 1941, three interesting papers (unpublished) dealing with heavy-media separation (sink-float) processes of ore concentration as practiced in four commercial units in the United States were presented by Victor Rakowsky, Grover Holt, Elmer Isern and Robert Ammon. These papers gave an excellent exposition of the principles of sink and float, as well as the operating practice in two iron-ore-beneficiation plants, the Harrison and the Merritt, of Butler Brothers, in Minnesota; the Central mill of the Eagle Picher Mining and Smelting Co.; and the Mascot mill, of the American Zinc, Lead and Smelting Co. Augmented by pictorial descriptions and a working model demonstrating the processes, these papers evoked a great deal of interest and discussion. In fact, in reporting the high lights of the meeting in the April 1941 issue of Mining and Metallurgy, Professor Taggart made the statement that " preconcentration by heavy suspension was Miss A.1.M.E 1941 so far as milling is concerned." Although to date the greatest application of heavy-media separation from the tonnage point of view has been for the treatment of lead, zinc and iron ores, these processes have a much wider field of usefulness. In this regard, it is to be noted that recently new heavy-media separation plants for treating cassiterite ore and garnet ore have been placed in successful operation. Moreover, numerous other types of ores have been found to respond well to these processes when tested on a semi-commercial scale, and it is expected that in the near future a considerable number of new plants will be erected. In view of the fact that heavy-media separation processes offer such attractive possibilities, particularly now, when the mining industry is being called on for an even larger production than ever before has been attempted, despite shortages of labor and supplies, it was felt that a description of some of the successful separations that have been worked out during the past year in the Ore Dressing Laboratory of the American Cyanamid Co. on a variety of ores of strategic importance would be of interest. The purpose of this paper, therefore, is to present the essential data relating to investigations of heavy-

Jan 1, 1943

By A. W. Jenike

A theory of gravity flow of bulk solids like ores, concentrates, coal is outlined and an example of design for unobstructed flow is given. Mass-flow and plug-flow patterns are defined and related to the geometry of the bin. The effect of these patterns on segregation, first in-first out flow, and caking is described. This paper is a report on the results from the AIME sponsored project "Flow of Bulk Solids" which was carried out under the author's direction at the Utah Engineering Experiment Station, University of Utah, during the period 1956-1962. The theory has been applied to the design of numerous industrial storage plants. A QUANTITATIVE METHOD OF DESIGN FOR FLOW There is hardly an industry which does not store and handle solid materials in bulk form. When the volume of the solids is large, gravity is invariably relied upon to cause the solids to flow out of storage, through channels and chemical reactors. Such materials as ore, coal, cement, flour, plastics, clay, soil, to which a general term of bulk solids is applied, flow by gravity or are expected to flow by gravity in thousands of installations and by billions of tons annually. The chemical and process industry depends on gravity flow of solids in process and out of storage. Mining relies on gravity flow in block-caving, in ore passes, as well as in storage and loading bins. Agriculture uses gravity flow in elevators, in feed plants, and in farm silos. In practice, satisfactory gravity flow is seldom attained. Such problems as doming, piping (rat-holing), lack of live capacity, segregation, deterioration in storage, harass industry. In spite of the universality of these problems, until recently, there has been no theory of solids flow, no method of predicting how a solid would behave, and how the channel, bin, or hopper should be designed. In the late nineteen forties and early fifties, the theory of plasticity came of age and simultaneously the computer became widely available. These two factors permitted the development of a theory of flow of bulk solids. The work was conducted during the years 1953-1961. In conjunction with the development of the theory a method to measure the flowability of solids was also developed1-7 and the theory was ap-plied to the design of ore pockets, storage plants,16 chemical reactors and adsorption columns. A comprehensive report of this work is given in a previous work." THEORY OF FLOW The most important question which a theory of flow has to answer is: what conditions need to be satisfied for a given solid to flow uniformly and without obstructions through a channel? First of all, the following observations are made:

Jan 1, 1967

By G. B. Walker, S. J. Swainson, S. A. Falconer, H. H. Vogel

During the past few years much interest and attention has been focused on a relatively new method of ore concentration, which utilizes the principles of sink and float and employs as the heavy medium a suspension in water of a finely ground solid, such as galena or ferrosilicon. Although a relatively recent development, much progress has already been made in applying heavy-media separation processes to a considerable number of ores. Eight plants in this country and abroad are now treating approximately 10 million tons of ore annually by heavy-media separation (sink-float) processes, including lead-zinc, lead, iron, garnet, tin and tungsten. At the annual meeting of the A.I.M.E. in 1941, three interesting papers (unpublished) dealing with heavy-media separation (sink-float) processes of ore concentration as practiced in four commercial units in the United States were presented by Victor Rakowsky, Grover Holt, Elmer Isern and Robert Ammon. These papers gave an excellent exposition of the principles of sink and float, as well as the operating practice in two iron-ore-beneficiation plants, the Harrison and the Merritt, of Butler Brothers, in Minnesota; the Central mill of the Eagle Picher Mining and Smelting Co.; and the Mascot mill, of the American Zinc, Lead and Smelting Co. Augmented by pictorial descriptions and a working model demonstrating the processes, these papers evoked a great deal of interest and discussion. In fact, in reporting the high lights of the meeting in the April 1941 issue of Mining and Metallurgy, Professor Taggart made the statement that " preconcentration by heavy suspension was Miss A.1.M.E 1941 so far as milling is concerned." Although to date the greatest application of heavy-media separation from the tonnage point of view has been for the treatment of lead, zinc and iron ores, these processes have a much wider field of usefulness. In this regard, it is to be noted that recently new heavy-media separation plants for treating cassiterite ore and garnet ore have been placed in successful operation. Moreover, numerous other types of ores have been found to respond well to these processes when tested on a semi-commercial scale, and it is expected that in the near future a considerable number of new plants will be erected. In view of the fact that heavy-media separation processes offer such attractive possibilities, particularly now, when the mining industry is being called on for an even larger production than ever before has been attempted, despite shortages of labor and supplies, it was felt that a description of some of the successful separations that have been worked out during the past year in the Ore Dressing Laboratory of the American Cyanamid Co. on a variety of ores of strategic importance would be of interest. The purpose of this paper, therefore, is to present the essential data relating to investigations of heavy-

Jan 1, 1943

By W. A. Anderson

Recrystallization of cold-worked metals has long been known to proceed by a process of nucleation and growth.' When a cold-worked metal is heated to a temperature at which recrystallization will ensue, nuclei of new grains, essentially strain-free, appear and grow. As the process proceeds, nuclei continue to appear and to grow, until the cold-worked matrix has been entirely consumed and recrystallization has been completed (Fig. I). Conducted isothermally, a measurement of the fraction of the matrix recrystallized plotted against time, yields an isothermal recrystallization curve, showing the time course of the recrystallization process (Fig. 2).2 Evidently, then, the rate of recrystallization is determined by the rate at which nuclei form and the rate at which they grow. The rate of nucleation N is the number of nuclei that form in unit time in unit volume of the unrecrystallized matrix, and the rate of growth G is the increase in radius of the recrystallized grain per unit time. In recent years attempts have been made to determine N and G as these vary with the well-recognized variables affecting recrystallization: time, temperature, degree of deformation, etc.1 Such studies yield information that is more fundamental than that conveyed by the conventional recrystallization diagram,' since the rate of recrvstallization is thus analyzed into its two component rates3 Methods are now available by which N and G can be measured, and analytical expressions have been developed for the interrelationships among N, G, the isothermal recrystallization curve, and the final grain size, which greatly facilitate analysis.2-4 The application of these methods has been demonstrated recently for the recrystallization of silicon ferrite.2 Data on N and G in dependence upon the recognized recrystallization variables are, however, very fragmentary;" values of N and G have been determined for some metals, but the effect of temperature, which would yield the fundamentally important activation energies, has been too little studied. Thus far there has been no detailed study of the recrystallization of any one metal in terms of X and G ovcr appreciable ranges of the variables time, temperature, degree of deformation, and original grain size. It is the purpose of the present paper to provide such a study, employing aluminum.

Jan 1, 1945

By R. A. Salathiel, A. D. Kaiser, P. H. Monaghan, B. E. Morgan

The productivities of many hydrocarbon-bearing for-rnntions appear to be reduced during drilling, completing and repairing operations. The reason for these othcarwise unexplainable low productivities may be a drastic reduction of formation permeability immediately surrounding the borehole. A possible cause of the reduced permeability is swelling and dispersion of clays present in porous media when contacted by fresh water or mud filtrates. Hence, the invasion of fresh water or mud filtrate into hydrocarbon-bearing formations that contain clays may cause low productivities as a result of formation damage. Present laboratory investigations have yielded results which supplement existing literature on formation damage. An expanded-type clay, montmorillonite, way found in hydrocarbon-bearing formations not previously analyzed. When sand columns and formation cores containing montmorillonite were contacted by fresh water, their oil permeabilities were reduced. This reduction in oil permeability way restored partially but not completely by a repair procedure, i.e., flooding with kerosene containing organic agents or flooding with water containing electrolytes. Hence, where montmorillonite is present in formations, prevention of formation danzage was indicated to be the only complete solution to the problem. To prevernt formation damage, results suggested use of an approximately 1 per cent solution of calcium chloride or stronger solutions of sodium or potassium chloride. In conventional rotary drilling operations the wall of the hole is exposed to drilling mud for days, weeks, and in some instances for as long as several months. During this time, drilling mud filtrate seeps slowly into formations surrounding the hole. The permeability and stability of many formations, especially those containing clayey materials, are impaired by the mud filtrate. Often interaction between the mud filtrate and the formation causes drilling and production difficulties. Serious reduction in productivity of oil and gas formations during drilling, completing and repairing wells has been noted often in recent years. Cases are known of development wells which produced only small volumes of fluid upon completion. However, after a period had elapsed, they began to produce oil or gas in commercial quantities. In other cases, results of drill-stem tests taken during the drilling of deep wells have indicated good production should be obtained from shallow formations. Later difficulty has been experienced in obtaining production from these shallow formations which had remained in contact with drilling muds for an extended time. In yet other cases wells have failed to attain the productivities expected from previous performance after the use of drilling mud as a circulating fluid during workover operations. It is evident from the field behavior cited that the productivities of certain oil- and gas-bearing formations have been damaged by exposure to drilling muds. This reduction in well productivity, called "formation damage", causes serious consequences. In development wells, expensive remedial operations are incurred. In wildcat wells, good formations may appear to be marginal or even non-productive. The importance of formation damage has been recognized by a number of investigators1-s who have considered the effects of fresh water, saline solutions and aqueous mud filtrates on the permeabilities of formations. A general conclusion from such studies is that interaction between water and formation clays reduces permeability of reservoir rock and that the permeability decreases as salinity of the water decreases. Data in these references, however, concern the permeability change with only a single fluid present. A more pertinent and direct consideration in the production of oil and gas from wells is the permeability change when two fluids, oil and water, are present. Recognizing this, Nowak and Kreuger2 and Bertness1" considered several ways in which mud filtrates and saline solutions caused reductions in the oil permeability of formation cores. Investigations discussed here were designed to supplement information in the literature on changes in oil

By O?Harra B. M.

THE work here described had for its purpose the procuring of data from which some quantitative estimate might be made of the results obtainable by using oxygen-enriched air in roasting zinc ores on a commercial scale. The principal metallurgical advantages of using enriched air in roasting zinc ores would be: 1. The rate of roasting would be increased, with consequent gain in the capacity of the roasting furnace. 2. As less air would be required for roasting, the volume of hot gases leaving the furnace and the heat carried out of the furnace as sensible heat in these gases would be less per ton of ore roasted; partly for this reason and partly because of the increased quantity of heat generated in the furnace by the larger amount of ore that could be roasted, the consumption of fuel by the furnace would be lessened; and by the use of air sufficiently enriched with oxygen the necessity of using fuel might be entirely obviated. 3. Roaster gas having a higher SO2 content could be produced; this would make possible greater capacity and more economical operation of the sulfuric-acid plant. Certain phases of the application of enriched air to roasting can be worked out only by experimenting with a furnace of commercial, or at least semicommercial, size. Thus the precautions necessary to secure proper. distribution of heat in the furnace;1 the volume of enriched air; and the proportion of oxygen in this air, necessary to give the desired increase in roasting capacity of the furnace and in SO2 content of the roaster gases;; and the most desirable frequency of raking, thickness of

Jan 11, 1924

By C. W. Washburne

Recently, Messrs, Mills and Wells1 published a thorough chemical study of the waters associated with oil in parts of the Pennsylvania, Ohio, and West Virginia region. Many of their conclusions are of general application and the writer wishes to discuss some of these. Messrs. Mills and Wells show that the composition of the deep brines oi the Appalachian fields is such as would be produced by the evaporation of sea water and the precipitation of sodium chloride, combined with reactions with hydrocarbons and other substances. The brines are altered, also, by considerable mixing with meteoric water. They give good reasons for believing that the concentration of the brines was produced by evaporation in the rock pores induced by migrating gas, much of which probably escaped to the surface of the ground. This hypothesis was considered by the writer in a former paperJ2 in which main stress was laid on a second hypothesis, that the excess of chlorine in the deep brines may have been due to the entrance of solutions rich in magnesium and calcium chloride which ascended from a deep, possibly intratellurie, source. Messrs. Mills and Wells present good arguments for the first hypothesis. Underground evaporation by ascending gases probably will be accepted as the best available explanation of the concentration and composition of deep well waters. They have not considered the possibility that salt waters in deep sands may be concentrated by the diffusion of water vapor through gas into shale. The writer has given reasons3 for believing that capillary forces concentrate gas and oil in the larger openings of rock, such as the pores of sandstones embedded in shale. The gas underground must be nearly saturated with water vapor at all times, because it always is in contact with the interstitial water of enclosing shales and of the sandstone. Experimental studies of soil moisture have shown that approxi-

Jan 1, 1921

By W. M. Peirce

ON May 16, 1871, twenty-two men met in Wilkes-Barre, Pennsylvania, and founded the American Institute of Mining Engineers.* If we could transport ourselves back to that year and survey the state of science and technology in general, and, in particular, the field of our immediate interest-nonferrous metals-we would feel a justifiable pride in what had been accomplished up to that time. These accomplishments in the metal field were at the moment in the process of documentation by an Englishman, J. A. Phillips, in a new 700-page edition of his book to be published in 1874 under the title of "Elements of Metallurgy." True, looking over his shoulder, we would smile to read that "all metals are capable of assuming a crystalline form under favorable conditions," and that tensile testing is done "by adding weights to a firmly suspended wire until it fractures," and we would find only three pages on aluminum and none on magnesium. We would, however, find an astonishing wealth of detailed knowledge on iron and steel and the then common nonferrous metals and alloys such as brass and bronze. But if we possessed a little prophetic vision as we directed our attention to the short period that had elapsed since the close of the Civil War, we

Jan 1, 1947

By James A. Barr

Phosphate rock is a natural rock containing one or more phosphate minerals usually calcium phosphate, of sufficient purity and quantity to permit its use, either directly or after beneficiation in the manufacture of commercial products.1 The principal minerals in phosphate rock have the apatite structure which may be represented by the type formula: Ca10(X2) (PO4)6 where X represents the hydroxyl group (OH), chlorine or fluorine, either singly or collectively. The calcium may be partly replaced by sodium, magnesium, and other positive ions such as manganese, strontium, lead, uranium, cerium, yttrium and other rare earths. The PO4 radical may be partly replaced by small quantities of UO4, AsO4, SiO4, CO3, SO4, or Vo4. A typical commercial rock is usually a calcium phosphate containing 3 to 4 pct fluorine, the major impurities being limonite or other iron oxides, clay, aluminum phosphates and silica as quartz sand. A little vanadium is present in most of the domestic rock deposits (except the Tennessee Brown Rock), according to Jacob, Hill, Marshall and Reynolds! A little uranium occurs in the Florida leached zone, as will be brought out later. The chemical analyses are reported as P205, or tricalcium phosphate Ca3(PO4)2, the latter often designated by the trade name BPL (bone phosphate of lime). Commercial analyses usually report iron and alumina as oxides, lime as CaO and silica or insoluble. Colony3 examined many samples of apatite, staffelite, dahlite and American phosphorites and concluded that all have identical X-ray diffraction patterns. The phosphates in the phosphate rock have very minute crystalline structures. The mineral apatite Ca3(F.Cl) (PO4) 3 is the principal primary source of the element phosphorus, and occurs widely distributed in igneous rocks but rarely in a minable mass. Only about 12 pct of the world production of phosphate rock comes from primary apatites; the remainder is derived from secondary phosphorites. These phosphorites have been formed by the alteration of sediments by solutions containing phosphoric acid. Such solutions have come from the weathering or leaching of igneous rock containing apatite, bone deposits of prehistoric animals, marine life or guano deposits. These phosphorites are mostly alterations of phosphatic limestones. The sedimentary phosphate deposits are of marine origin and may have been enriched by subsequent solution of the more soluble calcium carbonate by waters containing carbon dioxide, by physical concentration by wave action, and by redeposition of the dissolved phosphate ions. Uses of Phosphate Phosphorus is the spark of life and is the structure builder and one of the main elements of plant food (fertilizer). Without phosphorus, life cannot exist. A "complete" plant food[t] in addition to phosphorus compounds contains potash, which acts as a catalyst to convert nutrients to useful forms, nitrogen to supply the growth element and many minor elements. The cycle of supply of phosphorus is from the apatite to solution and soil, absorption of plant life, decay and return to the soil or by animal life feeding on the plants. With insufficient supply of phosphorus in vegetation, life is not prolific. If crops are removed from

Jan 1, 1960

Jan 1, 1954

By George I. Smith

Jan 1, 1985

By Frank N. Speller

Jan 1, 1934

Jan 1, 1908

By W. R. Hicks, J. E. Pollock, E. Camp

In the oil-refining industry, steel comprises by far the greatest proportion of the materials used in construction work, but with an enormous number of alloy steels and nonferrous alloys available, and a greater knowledge of their properties and corrosion resistance, a substitution first in the "hot spots" and then in locations of moderately severe corrosive conditions will be made as the greater expense can be justified. In new construction work, advantage is taken of the experience already gained and appropriate materials used, whether for high temperatures and pressures demanding additional strength or for corrosive conditions. The locations, however, where equipment in operation constantly requires replacement will soon become evident, as will the necessity for replacement in more resistant materials, if considerable down-time is to be avoided. In what direction and how far to go in the matter of alloys then becomes a question of the highest importance. Obviously, any replacement with more costly material must be justified economically by the promise of longer life, thereby saving both material and installation costs besides the reduction of loss of production. Where the equipment is overcapacity and a regular schedule of cleaning periods is in force, the last item frequently must be ruled out and justification made on the basis of the first two only. Installation of material that will outlast the remainder of the equipment and have no recovery value must also be avoided; this is particularly important in temporary construction or in old equipment that will soon become obsolete. Test Methods Either one of two methods or a combination of both, in the absence of reliable data in similar services, may be adopted to determine to what extent replacement with other, and perhaps more expensive, materials is justified. A unit may be constructed incorporating different metals or alloys so that comparative service may be obtained under the same service conditions; this has been applied in many instances, such as condenser and tank construction, but the opportunities for inspection may be few and

Jan 1, 1935

By C. H. Mathewson, W. R. Hibbard, Robert Maddin

A satisfactory mathematical relationship between shear, elongation and change of orientation in the axial straining of a single crystalline rod or wire may be based on a simple model in which blocks, representing glide lamellae, glide over one another and rotate so as to maintain the original fixed position of the axis as the wire elongates.' Obviously such a model gives no information concerning strain-hardening or the atomic adjustments at the sliding surfaces and their influence on the internal structure of the blocks. Moreover such an operation could be conducted with rigid blocks only by using self-aligning grips or a flexible attachment which would permit the adjacent blocks to freely assume their changing orientations. There are many unsolved problems (see Andrade2) concerning the manner in which nature departs from the simple model in permitting the essentials of slip, rotation and elongation to occur along with strain-hardening and the appearance of glide lamellae of various dimensions and special characteristics, not fully appreciated at the present time. This paper describes part of an extensive investigation on the development and characteristics of glide ellipses in single crystalline alpha brass rods and is especially concerned with the observation of cross-slip in crystals oriented wholly within the range of slip on a single system according to the generalizations first presented by Taylor and Elam in 1923.³ Experimental Procedure Half-inch rods of alpha brass (nominally 70 pet Cu, 30 pet Zn)* were converted into single crystals by melting and gradual solidification in a graphite mold according to the Bridgman method.4 In order to remove any coring, the crystals were homogenized at 800°C for 16 hr and tested by etching with a 50 pet nitric acid solution. The back-reflection Laue technique as described by Greninger6 was used for determining the orientations of the crystals. Standard stereographic operations were employed to locate the specimen axis in a triangle of the Taylor and Elam3 projection so that the slip plane and direction could be predicted. The lineage structure reported by Buer-ger6 was present in the crystals used in this investigation. However, only crystals were used in which the internal differences in orientation did not exceed two degrees. Very little is known concerning the effect of the presence of a lineage structure on the detailed mechanism of plastic deformation.

Jan 1, 1949

By C. H. Mathewson, Robert Maddin, W. R. Hibbard

A satisfactory mathematical relationship between shear, elongation and change of orientation in the axial straining of a single crystalline rod or wire may be based on a simple model in which blocks, representing glide lamellae, glide over one another and rotate so as to maintain the original fixed position of the axis as the wire elongates.' Obviously such a model gives no information concerning strain-hardening or the atomic adjustments at the sliding surfaces and their influence on the internal structure of the blocks. Moreover such an operation could be conducted with rigid blocks only by using self-aligning grips or a flexible attachment which would permit the adjacent blocks to freely assume their changing orientations. There are many unsolved problems (see Andrade2) concerning the manner in which nature departs from the simple model in permitting the essentials of slip, rotation and elongation to occur along with strain-hardening and the appearance of glide lamellae of various dimensions and special characteristics, not fully appreciated at the present time. This paper describes part of an extensive investigation on the development and characteristics of glide ellipses in single crystalline alpha brass rods and is especially concerned with the observation of cross-slip in crystals oriented wholly within the range of slip on a single system according to the generalizations first presented by Taylor and Elam in 1923.³ Experimental Procedure Half-inch rods of alpha brass (nominally 70 pet Cu, 30 pet Zn)* were converted into single crystals by melting and gradual solidification in a graphite mold according to the Bridgman method.4 In order to remove any coring, the crystals were homogenized at 800°C for 16 hr and tested by etching with a 50 pet nitric acid solution. The back-reflection Laue technique as described by Greninger6 was used for determining the orientations of the crystals. Standard stereographic operations were employed to locate the specimen axis in a triangle of the Taylor and Elam3 projection so that the slip plane and direction could be predicted. The lineage structure reported by Buer-ger6 was present in the crystals used in this investigation. However, only crystals were used in which the internal differences in orientation did not exceed two degrees. Very little is known concerning the effect of the presence of a lineage structure on the detailed mechanism of plastic deformation.

Jan 1, 1949

By J. T. Norton

As cold working is an important feature in a great many of the fabricating processes now applied, this paper presents some ideas of the nature and results of the plastic deformation produced in this operation. The art of manufacturing metal for practical uses is very old and has undergone very great development. The science of metals has also developed very rapidly recently and the various processes to which ,metals are submitted are much better understood now than they were even a short time ago. All the knowledge that can be obtained on this subject is useful because it promotes efficiency in converting metal into finished articles. ATOMIC ARRANGEMENT IN CRYSTALS In the solid state all metals are crystalline. The atoms are arranged in, a definite symmetrical configuration, which is repeated at regular intervals, and thereby defines what we may term a lattice. Presumably . the atoms exist as positive ions. The dissociated electrons place themselves between groups of positive ions, and thus define a second lattice, an "electron lattice." From such a point of view, the crystalline forces which hold a metal together are the electrostatic attractions between positive ions and negative electrons. The particular type of lattice into which a metal crystallizes depends on the number of these lattice electrons given up by each atom, and is thus connected very closely with the chemical valence of the metal.

Jan 12, 1926

By J. E. Pollock, W. R. Hicks, E. Camp

In the oil-refining industry, steel comprises by far the greatest proportion of the materials used in construction work, but with an enormous number of alloy steels and nonferrous alloys available, and a greater knowledge of their properties and corrosion resistance, a substitution first in the "hot spots" and then in locations of moderately severe corrosive conditions will be made as the greater expense can be justified. In new construction work, advantage is taken of the experience already gained and appropriate materials used, whether for high temperatures and pressures demanding additional strength or for corrosive conditions. The locations, however, where equipment in operation constantly requires replacement will soon become evident, as will the necessity for replacement in more resistant materials, if considerable down-time is to be avoided. In what direction and how far to go in the matter of alloys then becomes a question of the highest importance. Obviously, any replacement with more costly material must be justified economically by the promise of longer life, thereby saving both material and installation costs besides the reduction of loss of production. Where the equipment is overcapacity and a regular schedule of cleaning periods is in force, the last item frequently must be ruled out and justification made on the basis of the first two only. Installation of material that will outlast the remainder of the equipment and have no recovery value must also be avoided; this is particularly important in temporary construction or in old equipment that will soon become obsolete. Test Methods Either one of two methods or a combination of both, in the absence of reliable data in similar services, may be adopted to determine to what extent replacement with other, and perhaps more expensive, materials is justified. A unit may be constructed incorporating different metals or alloys so that comparative service may be obtained under the same service conditions; this has been applied in many instances, such as condenser and tank construction, but the opportunities for inspection may be few and

Jan 1, 1935