Search Documents

By F. E. Harris

It has been said that carbon is "ubiquitous" with reference to iron alloys. Certainly at temperatures where carbon and iron form the solid solution, austenite, it may be readily added to, or removed from, steel surfaces. Differences in concentration potential are the sole requirements for carbon flow. To measure the rate of carbon flow, a proportionality factor, D, is arbitrarily expressed in units of (length)2 X (time)-'. If the term used for carbon concentration is weight Pet C, as is customary, then a factor must be found, changing this term to One of weight Per unit volume when the diffusion coeficient, D, is used in flow formulae. The determination of D values for carbon is complicated since D varies with the concentration itself. The Matano method has often been employed for systems involving a variant D. This method expresses all evaluation of unsteady flow whereby D is given a relationship with the numerical value of C-x slopes. The author contends that this solution is incorrect, except when D is invariant. The primary purpose of this paper is to support this contention. Here diffusion is controlled under two conditions of flow. The first part deals with the steady state; the second part considers unsteady flow under definite restrictions. Beginning with the fundamental concept, the development is continued until equations for C-x curves are obtained. The solution is then subjected to experimental data. It is realized that a great amount of reliable data is required for a rigorous proof. KO such research is claimed. Instead an attempt is made to set forth the physical significance of the diffusion mechanism, and particularly to express the factors which influence the flow of carbon in austenite. Of equal significance is the implication that gaseous media may be employed with reasonable accuracy in making these determinations. The Steady State Diffusion of Carbon in Au~tenite The fundamental experiment defining diffusion in solid metals may be readily performed for carbon in gamma iron.' For this experiment a thin plate of medium carbon steel is chosen. The surfaces of this plate may be taken as two parallel planes which may be considered infinite for points well in the Center of the planes. These two planes are held at different concentrations of carbon at a constant temperature. This temperature, 1700°F for example, is one where the single phase: carbon in solution with gamma iron, exists. When these conditions are held for a sufficient time the concentration of carbon of the different points of the solid ment down towards its steady state value. At points well removed from the ends, the concentration will remain the Same along planes parallel to the surfaces of the plate.

Jan 1, 1948

By F. E. Harris

It has been said that carbon is "ubiquitous" with reference to iron alloys. Certainly at temperatures where carbon and iron form the solid solution, austenite, it may be readily added to, or removed from, steel surfaces. Differences in concentration potential are the sole requirements for carbon flow. To measure the rate of carbon flow, a proportionality factor, D, is arbitrarily expressed in units of (length)2 X (time)-'. If the term used for carbon concentration is weight Pet C, as is customary, then a factor must be found, changing this term to One of weight Per unit volume when the diffusion coeficient, D, is used in flow formulae. The determination of D values for carbon is complicated since D varies with the concentration itself. The Matano method has often been employed for systems involving a variant D. This method expresses all evaluation of unsteady flow whereby D is given a relationship with the numerical value of C-x slopes. The author contends that this solution is incorrect, except when D is invariant. The primary purpose of this paper is to support this contention. Here diffusion is controlled under two conditions of flow. The first part deals with the steady state; the second part considers unsteady flow under definite restrictions. Beginning with the fundamental concept, the development is continued until equations for C-x curves are obtained. The solution is then subjected to experimental data. It is realized that a great amount of reliable data is required for a rigorous proof. KO such research is claimed. Instead an attempt is made to set forth the physical significance of the diffusion mechanism, and particularly to express the factors which influence the flow of carbon in austenite. Of equal significance is the implication that gaseous media may be employed with reasonable accuracy in making these determinations. The Steady State Diffusion of Carbon in Au~tenite The fundamental experiment defining diffusion in solid metals may be readily performed for carbon in gamma iron.' For this experiment a thin plate of medium carbon steel is chosen. The surfaces of this plate may be taken as two parallel planes which may be considered infinite for points well in the Center of the planes. These two planes are held at different concentrations of carbon at a constant temperature. This temperature, 1700°F for example, is one where the single phase: carbon in solution with gamma iron, exists. When these conditions are held for a sufficient time the concentration of carbon of the different points of the solid ment down towards its steady state value. At points well removed from the ends, the concentration will remain the Same along planes parallel to the surfaces of the plate.

Jan 1, 1948

By C. P. Proctor, J. B. Morrow

With numerous plans under consideration for coal classification, and with the advent of the Bituminous Coal Code, the intelligent sampling of coal has become increasingly important. To us it is rather significant that there have been very few fundamental studies of coal sampling in American technical literature since those of E. G. Bailey, which appeared in the Journal of Industrial and Engineering Chemistry in March, 1909. He covered the subject up to that time so thoroughly and in such an excellent manner that perhaps many other later students have felt that they could add very little to his findings. The recent studies of the British Engineering Standards Association have indicated the possibility of a somewhat different interpretation of Bailey's results, permitting the taking of smaller samples, and perhaps it will now be helpful to reopen this question. C. W. H. Holmes, in an informative series of articles on coal sampling recently published in Colliery Engineering, makes two rather interesting statements, as follows: It is scarcely surprising to find a lack of interest and knowledge regarding the sampling of coal not only in the mining industry itself but also among consumers of industrial fuel: at its best coal sampling is a dirty business, regarded as a nuisance and an expense by the commercial man, and usually as a nuisance and nothing else by the chemist. The writer can conceive only two classes of people who have never experienced any difficulty in obtaining representative samples of coal from wagons; those who have never tried to, and those who have never had the necessity or desire to check the accuracy of their work. The primary purpose of this paper is to present some tabulated data of the more significant results of a sampling investigation undertaken during the last four years to obtain certain fundamental data on the variables connected with coal sampling and to point out that often assumptions have been made that are not in accordance with the facts. One of the standard sampling methods states:

Jan 1, 1936

By H. M. Ziesemer

PRIOR to 1909 that mountain of porphyry, known as. Sacramento Hill, had remained hardly touched but had always aroused suspicions as to the presence of ore within.. During that year, exploratory work was started by underground methods; drifting and raising continued until 1913. It was proved that a mineralized zone existed, the limits of which had not been determined; so, because of the lower costs of exploratory work and the greater desirability of vertical sections, it was decided to prove the extent of the ore zone by churn drills. Drilling continued until the year 1917, when it seemed almost certain that the horizontal limits of the orebodies had been determined. Ore continued in depth in one direction beyond a point where it was economical to explore by churn drilling; this extension is still being developed by underground methods. The irregularities of the boundaries of the ore zones, together with the variable grades of ore encountered, made it necessary to drill on the corners of 100-ft. squares. Two ore zones were proved, known as the East and West Orebodies. The Sacramento Hill porphyry stock intruded into the Dividend fault. The fault ran roughly east and west with a dip to the south, having pre-Cambrian schists on the north against Paleozoic limestone on, the south. This intrusion was accompanied by a silica breccia on the south periphery, along the limestone contact side. The ore lay in the silica breccia and in the porphyry, some distance from the breccia. No ore was found in the heart of the porphyry mass on the north side, along the schist contact. The West Orebody is elliptic in shape, having a major axis of 1200 ft. (366 m.) and a minor axis of 800 ft. (244 m.); these diminish with depth until, at 300. ft., the axes are 500 ft. and 300 ft., respectively. The ore consists of chalcocite, some bornite, chalcopyrite, and considerable pyrite in a silicious gangue. About 30 per cent. of the copper is caused by

Jan 2, 1922

By K. J. Rosengren

INTRODUCTION Mount Isa Mines Limited operates a major mining complex at Mount Isa in northwest Queensland, Australia. The location is arid and remote, some 600 miles distant from the nearest port of Townsville on the eastern coast (Fig. I). Current mine production is 6 million long tons per annum comprising 3.8 million tons of copper ore and 2.2 million tons of silver-lead-zinc ore. Copper ore production is scheduled to increase to 5.8 million long tons per annum by 1973 and a new silver-lead-zinc mine is being developed at Hilton, 13 miles north of Mount Isa. The Mount Isa and Hilton orebodies occur in a single stratigraphic member, termed the Urquhart Shale. This shale is conformable with several other sedimentary formations striking north-south and dipping approximately 65º west. The silver-lead-zinc orebodies occur in bands conformable with the shale bedding and tend to be of tabular shape, varying in width from a few feet to nearly 200 ft. The copper orebodies occur in breccia bodies, locally known as "silica-dolomite", within the Urquhart Shale and tend to be more irregular and massive with widths up to several hundred feet. The detailed geology is described by Bennett (1 2). At present, production comes almost entirely from underground operations with only about 25,000 tons per year of carbonate ore from open pit operations. The mining method used in the copper orebodies is sublevel open stoping with pillar recovery by pillar blast before stope filling or by sublevel caving after stope filling. A large primary sublevel caving operation was also carried out until recently in one of the orebodies. The wider lead orebodies are mined by sublevel open stoping, with or without pillar recovery, while cut and fill stoping is used in the narrower orebodies. Details of the mining methods are given by Davies (3). The company's interest in open pit mining stems from a large open pit which was mined out in 1965 and a further large open pit planned for future production. In addition, the company is currently evaluating several large ore deposits in Australia and New Guinea. All of these orebodies would be mined by open pit methods and rock mechanics studies of slope stability are now a standard feature of all open pit evaluations.

Jan 1, 1972

By T. Egleston

The origin of gold both in placer deposits ancl in veins, and especially the origin of nuggets, has been the subject of repctated discussions and investigations, which have been recently brought to my attention by several extremely interesting specinlens sent to me for examination, and mare especially by the one exhibited at the meeting of the Institute in February, 1880.* In the year 1874 I made some exan~inations of the hydraulic mines of California, and was very nluoh struck with the distribution of the gold throughout these deep placers, which were almost invariably poor on'the surface, while gradually growing richer towards the bedrock. The constant presence of fossil wood, and the large quantity of organic matter contained even low down in these beds, was also remarkable. Not being satisfied with the various theories advanced to account for the formation of these deposits, I began an investigation early in the pear 1879 on the conditions of solubility of gold and the causes of the loss in working gold ore in a large way. The researclles which I have undertaken show that gold must be considered a soluble rather than an insoluble metal, and that the conditions of solution are such as will be found anywhere where gold is likely to occur, and the solution may take place even under the ordinary circumstuncee of surfiace drainage, and may be going on freely even where the presence of gold has never been suspected, and that there are causee enough in nature to produce the solution of the gold in sufficient quantities to account for all the phenomena of both the vein and placer formations. The general theory with regard' to the formation of these placer deposits and nuggets has been that they were the result of the deatruction of pre-existing. vein-matter, which does not accord with the fitcts as sholvn in the deep placer deposits. The gold in such case would be distributed in layers of unequal richness throughout

Jan 1, 1881

By A. Hellawell

Specitlrens of the Al-Ge eutectic alloy have been frozen unidivectionally at rates between 2.5 x 10-6 and 2.5 x 10-4 cm per sec and the structure examined by optical and X-ray methods. There is no epitaxial relationship between phases, the aluminum having random orientation and the germanium a preferred (011) fiber textuve. Lamellar colonies which are BINARY eutectic alloys occur between either silicon or germanium with the metals aluminum or silver. common in this alloy are constructed from axial and nonaxial (111) plates of germanium which are related by a variety of twin configurations. Irregular or globular regions of the microstructure are composed of continuous single crystals of each phase, the germanium being heavily twinned. There is limited solid solubility in these systems, and the eutectic phases all involve diamond cubic with fcc crystal structures. In the microstructures of these eutectic mixtures the silicon and germanium crystals exhibit an almost infinite variety of shapes which are notably sensitive to

Jan 1, 1968

By C. A. Heiland

The Eötvös torsion balance permits the measurement of certain second derivatives of the gravity-potential, which are known as the gradients of gravity and the curvature values for an equipotential plane of gravity. These quantities are influenced on level ground by the configuration of the masses underneath. Hence, the torsion balance has gained great importance for the location of geological structures and thus indirectly for the discovery of oil and other mineral deposits. If the ground is not level, however, the measurements become more difficult, because the superficial mass-irregularities also produce more or less considerable disturbances. It is necessary, therefore, to determine the shape of the surrounding topography by leveling as well as by consulting topographic maps and to compute its influence upon the torsion balance. The correction thus determined is called, in general, the topographic correction; it is composed of two constituents, the terrain correction and the cartographic correction. The terrain correction would be that part of the topographic correction as derived from the direct leveling of the area surrounding the station, whereas the data for the computation of the cartographic correction are obtained from a topographic map, usually beginning with a radius of LOO meters, as under most circumstances it is difficult to level along a arger concentric circle about the station. Principle of Topographic Correction The principle of all topographic corrections is to assume a homogene-ous compositon of the masses around the station in regard to specific gravity as well as a mathematical shape of the topography. The results become the more accurate the closer this mathematical shape is to the actual configuration of the terrain, but naturally the amount of necessary computation also increases. If a standard correction with fixed dis-ances is adopted, the middle error of this method will, therefore, increase as the irregularity of the terrain. Hence, the application of the torsion balance in mountainous areas may be successful only if the disturbances due to heavy masses underneath the surface are so large as to exceed onsiderably the increased middle error due to rugged topography, or,

Jan 1, 1929

By Charles White Merrill, James W. Pennington

No metallurgical process developed in the 20th century compares with froth flotation in its effect on the mineral industry. Processes like gravity - concentration, amalgamation, and pyrometallurgical reduction are of ancient origin; others like cyanidation and electrolytic reduction were well established by 1900. Such metallurgical processes as heavy-media separation, ion-exchange, and solvent extraction belong to this century, but their influence is small compared with froth flotation. Data collected by the U. S. Bureau of Mines* in a canvass of 202 froth flotation plants reveal that, in 1960, 198- million tons of material was treated to recover 20-million tons of concentrates which contained approximately $1 billion in recoverable products. SIGNIFICANCE OF FLOTATION Froth flotation as described in this chapter refers to a wet process for separating properly ground mineral particles into two or more products. It involves the separation of mineral particles from each other in a liquid pulp by means of air bubbles. Finely crushed ore is agitated in water with the addition of air or other gases. Various chemicals and oils are added to cause the selected mineral particles to attach themselves to the air or gas bubbles. These bubbles, carrying the mineral particles, rise to the surface where they are removed in a froth, while the other particles remain suspended in the pulp. The earliest flotation divided the raw material into two products: a bulk concentrate that was removed as a froth and a tailing that remained in the flotation machine. The froth usually contained the valuable constituents. The successful application of such a process depended on the recovery of a single concentrate from which one or more valuable constituents could be recovered by a chemical or smelting process. With the advance of the art, however, the principle of selective flotation, by which two or more relatively pure products could be recovered from complex raw materials, was evolved. Other chapters in this volume describe the developments during the last 50

Jan 1, 1962

By Louis A. Panek

Ground movements in the zone adjoining an active cave were measured at four sites in the San Manuel Mine. Measurements were made to detect extension and inclination, basic components of displacement, which can readily be duplicated by mine personnel using relatively simple equipment. The displacements demonstrated the development of a zone of strain relief surrounding the active cave, within which the ground tends to migrate toward the cave, and extension cracks develop tangential to the cave. This expansion of the ground surrounding an active cave can be exploited to promote future caving; it also creates special problems with respect to the design of an effective ground support system for mine openings in the production area.

Jan 1, 1981

By Charles H. Behre

UNDER the caption "fault," geologists intend to include all mass movements of solid rocks over adjacent rock masses. When these are studied long after their origin, however, circumstances make it possible to recognize as "fault" only formations showing clear evidence of actual movement of one side with respect to the other. Necessarily the chief evidence consists of the offset of a vein, bed, or other key structure. Planes of movement parallel to the bedding, or nearly so, are recognized with difficulty or are overlooked and hence many important faults are wholly unrecorded. Indeed, among standard American references on structural geology, one alone emphasizes the importance of bedding-plane movements and that one only briefly1. For some time the writer, cognizant of this difficulty, has paid special attention to such movements, both as observed in the field and as recorded in the literature. It is believed that enough data are now at hand to justify a short discussion. Its purposes are fivefold. It is desired first to briefly classify and describe at least the more common kinds of bedding-plane faults, and second, to examine the causes and manner of their formation, at least in instances where the subject has not yet been well covered by other investigators. Third, certain by-products of bedding- lane movements are of such conspicuous importance to the economic geologist and mining engineer as to merit mention. Fourth, concrete illustrations should be placed before the reader in order to lend reality and to furnish a basis of comparison with his experience; such illustrations will necessarily be scattered through the text of this paper. They are only in part from the writer's own field observations. The fifth and prime objective of this paper is to direct attention to the great importance of movements on the bedding planes, in the hope that the recognition of such movements and their significance may simplify mining problems.

Jan 1, 1937

By M. H. Harris

A solution has been obtained to the problem of calculating flow into a cased and perforated well. Equations describing the idealized system were solved by numerical analysis techniques on a high-speed digital computer. Computer experimentation indicated that the results are within 3 per cent of the exact solution. Computed results are presented as an apparent skin effect, on a series of dimensionless working curves. Productivity ratios can be rapidly calculated from these data for the wide range of wellbore and reservoir properties actually encountered in field practice. Any reasonable vertical unisotropy ratio can be included in the computation. Productivities can be calculated for wells perforated in a regular pattern, a single horizontal plane or a vertical line on one side of the casing. Solutions for asymmetrical perforation patterns can he easily obtained from the working curves. Solutions for flow into sells completed with a horizontal notch are also provided. Results show that productivity can be increased by extending perforation penetration. This is especially true for shallow penetrations. The highest productivity is obtained when perforations are arranged in horizontal planes, as opposed to a vertical line on one side of the casing. Four or five perforations in one plane will approach the maximum productivity. The effect of perforation hole diameter is small, and is rioticeable only in shallow penetrations. INTRODUCTION The perforating method of well completion has been successfully and widely used in most producing areas. In the past, the desired perforation results were achieved by simply shooting numerous large holes in the casing. A perforating scheme for an area, or particular well, was established by evaluating two types of experimental data: the well flow index and the productivity ratio.' 3 The well flow index test is a means of determining the relative flow capacity of perforations in a linear system. This test also gives information on the perforation size, shape and hole damage which can be expected under well-bore conditions. However, relative flow data from this test cannot be accurately tarnsformed into the radial wellbore system. Thus, no true indication of the productive capacity of a perforated well can be obtained from the well flow index test. A well productivity ratio is derived from electrolytic models built to simulate perforated wells. Available productivity ratio data 2,3 are limited in that all important variables are not extensively evaluated. For example, data are limited to well radii of 3 and 6 in., and to maximum perforation penetration of 1 ft. Practically no information is available on the pattern of flow into a perforation. The effect of various perforation patterns on well productivity has not yet been determined and the effect of perforation diameter has not been thoroughly studied. Also, it will be shown that this type of electrolytic model data is probably in error by as much as 10 per cent or more. Modern completion techniques such as limited-entry perforating, single-plane fracturing, steam and hot air injection and chemical consolidation of incompetent formations all rely on injection and/or production from a limited type of completion. These completions may consist of several high-capacity perforations or a horizontal notch which is equivalent to an infinite number of perforations in one plane. Proper design of these new completion techniques requires, in part, accurate estimates of a well's productive capacity. Data on perforated and notched well productivity have been determined in this investigation. Results are presented as a function of the pertinent variables. Equations describing the idealized system were solved by numerical analysis techniques on a high-speed digital computer. DESCRIPTION OF PROBLEM PRACTICAL APPLICATION The computed results can be applied to wells which meet several general specifications. An external drainage radius of the well must be known or assumed, but the well need not be drilled on a regular pattern. The well must be cased and cemented through the entire producing interval. And, the casing must be perforated with one or more horizontal planes of perforations. The perforation pattern itself must conform to three geometrical requirements. 1. The perforations in a plane must divide the plane into equal angular segments (Fig. 1). Four perforations per plane would be 90" apart. 2. Perforations in a plane must be directly above or beneath perforations in adjacent planes. For two shots per plane, perforations would lie in the BB' plane (Fig. 1). 3. Horizontal planes must have equal vertical spacing and be separated from the top and bottom of the formation by one half the spacing interval. Single planes of perforations should be in the middle of the formation. This is shown in Fig. 2 where h is the formation thickness in a single plane conlpletion or the spacnig interval in a multiple plane completion. The spacing interval at the top and bottom of the formation may vary somewhat without causing an appreciable error in the productivity calculation if the formation is reasonably thick and there are many horizontal planes of perforations. A special provision has been made to calculate the productivity ratios of wells with uneven spacing intervals, or for the case where a single plane of perfora-

Jan 1, 1967

By C. M. Heath, B. W. Gonser

Soft solders are used principally in the automotive, can-making, building construction and electrical industries, but their field of usefulness extends well beyond these principal users to a vast list of miscellaneous applications where metal joints are required. The most common soft solders and the only ones considered in this discussion are those composed of lead and tin, with or without various relatively small percentages of impurities or additions. A small amount of antimony is often purposely added. As an indication of the importance of these lead-tin solders, 8620 long tons of tin were consumed in 1934 in the United States for making new solder, and during most of 1935 from 900 to 1000 long tons often were used each month. In addition, many thousands of tons of secondary solder are recirculated annually. A great many factors influence the properties of joints made with soft solders. Fluxes and the fluxing procedure used to prepare the surfaces to be joined in order to give a true metal-to-metal contact are among the most important of these factors. The temperatures used, cleanliness of the work and general soldering technique have their effect, but when results are unsatisfactory they are usually attributed to the metallic solder itself and the raw materials from which it is made. Sometimes criticism of the solder is justified. The wrong composition may be chosen for a given job, impurities may be present that ruin certain desired qualities, or uniformity may be lacking. A solder may even be looked upon with suspicion because of its ancestry, regardless of its true composition and behavior. To clarify the effect of slight differences in composition as found in commercially refined solders, a comparison of properties of solders grouped according to their origin has been undertaken. This investigation seeks to give practical information on the properties of tin-lead solders produced from virgin metals, from commercially refined secondary solder, and from an electrolytically refined crude

Jan 1, 1936

By L. C. Raymond

Valuations in the mineral industry differ from those of other enterprises because mines and oil wells have a definite life so cannot be considered a perpetuity. This requires that in any mineral-property evaluation the recovery of invested capital is necessary during the life of the property. Capital writeoffs for nonextractive industries are assumed to be continuously plowed back to sustain the operation and produce yields on the capital invested. The extractive or mineral industry, however, generally attempts to return to the investor both interest and principal during the life of a property. Normally this is done currently and the dividend includes both items. Where the mineral properly possesses large reserves and the life factor approximates a perpetuity, the return on investment is generally comparable to that of industrial stocks. The valuation of a mineral property, at best, is based on educated estimates and judgment factors. This is particularly true as it relates to estimating selling prices over a long term or assessing the quality of management. Also, it is possible to make various assumptions as to rapidity of working out the deposit, varying time for start-up of operations, varying earning rates, so as to obtain different results with the same basic facts. Thus it is not surprising that two engineers, irrespective of their abilities, may not agree exactly even when given the same facts, but their results should be close enough to be used in establishing a fair value for trading purposes. The valuation is no better than the source of basic data and the soundness of judgment factors. Fundamentally the basic principles of mineral valuation are similar for base metals, sulphur, oil, or any other mineral. Each mineral, however, requires an engineer to have a knowledge of such factors as its occurrence, distribution, mining and processing methods, and marketing problems in order to gather and analyze all the facts and data that have a bearing on the earning potential of the property. PRESENT VALUE OF A MINERAL PROPERTY In essence the present value of a mineral property is a sum of money in today's dollars that future earnings from the property are worth. It differs

Jan 1, 1964

By Earl C. Smith

Jan 1, 1935

By Charles H. Jacoby

During the past three decades an ever increasing number of uses for underground storage space has been developed. In some instances, the value of the space created has been so great that the host rock has been wasted. The preferential use of salt to host underground cavities is based on numerous factors, the primary two being low extraction costs and low permeability. Both dry and solution mined cavities have been created for the storage of a variety of materials. As the demand for underground storage and disposal grows, so must our selectivity of the materials to be stored.

Jan 1, 1985

By Earl C. Smith

Jan 1, 1935

By A. Blake Caldwell

Northwest frontier is here defined as Alaska, the Yukon, the Northwest Territories and northern British Columbia. The mineral potential of this area is great and will unfold in the decade ahead but now the largest single producer is the Pine Point lead-zinc mine in the NWT about 1200 km north of Edmonton, Alta., close to the south shore of Great Slave Lake. The mill, initially designed for 4540 mtpd, was expanded to 7250 mtpd in 1969. This operation is described in detail in Mining and Concentrating of Lead and Zinc, Vol.1, Chapt. 17, SME/AIME in the article by W. H. R. Gibney.

Jan 1, 1971

Jan 1, 1961

By Lester C. Uren

With the depletion of our older, and relatively shallow, oilfields and the necessity for securing new production from deeper horizons, much attention is being given to the improvement of oil-well pumps in order that they may function satisfactorily under the more difficult conditions imposed by increased depth. Until recently, practically all of the world's petroleum was secured from wells less than 3000 ft. deep, whereas horizons are now being explored to depths of from 5000 to 7000 ft. in some of the more prolific fields, and it seems probable that the greater part of the future supply must come from depths in excess of 3000 ft. While much of the early production in a new field is obtained by natural-flow methods, when the stimulus of high gas pressure fails, recourse must be had to some method of pumping. The perfection of a pump capable of economically and efficiently lifting oil from depths ranging from 3000 to 7000 ft. is therefore a matter of prime importance to the oil-producing industry. This paper is offered as an estimate of the present state of development of the oil-well plunger pump and as a review of the general principles involved in its operation in deep-well pumping. A design for a new type of oil-well pump embodying several novel features, is also described. Essential Parts of Oil-well Plungeb Pump The pump commonly used in lifting oil from wells in American practice is of the simple displacement type, in which a plunger equipped with a working, or traveling, valoe is given a vertical reciprocating motion in a stationary working barrel. The latter is suspended from the surface by tubing, submerged in the well fluid, and is equipped at its lower end with a stationary standing valve; Figs. 1 and 2 illustrate two common types of oil-well pumps. The simple cup-leather packed plunger of Pig. 1 has its counterpart in the long, hollow, cylindrical, polished steel plunger of Fig. 2; otherwise the two types are identical in the form and arrangement of their essential parts. Fig. 2 shows the additional feature of a "garbutt

Jan 1, 1927